Improve the Kconfig help text of the follwing i2c drivers:
* busses/i2c-pca-isa.c
* chips/pcf8574.c
* chips/pcf8591.c
These are hard to detect and building them into the kernel
results in long delays at boot.
March 2006, thread "I2C_PCA_ISA causes boot delays"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114360399415744&w=2
April 2006, thread "i2c-related 1-minute hang during bootup"
http://marc.theaimsgroup.com/?l=linux-kernel&m=114640992330721&w=2
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the ST m41t81 and m41t85 i2c rtc chips
to the existing m41t00 driver.
Since there is no way to reliably determine what type of rtc chip
is in use, the chip type is passed in via platform_data. The i2c
address and square wave frequency are passed in via platform_data
as well. To accommodate the use of platform_data, a new header
file include/linux/m41t00.h has been added.
The m41t81 and m41t85 chips halt the updating of their time registers
while they are being accessed. They resume when a stop condition
exists on the i2c bus or when non-time related regs are accessed.
To make the best use of that facility and to make more efficient
use of the i2c bus, this patch replaces multiple i2c_smbus_xxx calls
with a single i2c_transfer call.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch does some cleanup to the m41t00 i2c/rtc driver including:
- use BCD2BIN/BIN2BCD instead of BCD_TO_BIN/BIN_TO_BCD
- use strlcpy instead of strncpy
- some whitespace cleanup
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the bitmasks used when writing to the M41T00 registers.
The original code used a mask of 0x7f when writing to each register,
this is incorrect and probably the result of a copy-paste error. As a
result years from 1980 to 1999 will be read back as 2000 to 2019.
Signed-off-by: David Barksdale <amatus@ocgnet.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The m41t00 i2c/rtc driver currently uses a tasklet to schedule
interrupt-level writes to the rtc. This patch causes the driver
to use a workqueue instead.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A tasklet is not suitable for what the ds1374 driver does: neither sleeping
nor mutex operations are allowed in tasklets, and ds1374_set_tlet may do
both.
We can use a workqueue instead, where both sleeping and mutex operations
are allowed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, completely optional, removes from drivers/i2c/chips all the
drivers that are implemented in the new RTC subsystem.
It should be noted that none of the current driver is actually integrated,
i.e. usable without further patches.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop unused rogue i2c driver ID and nonsensical i2c class.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below converts a few i2c semaphores to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the miscellaneaous i2c chip drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate of BCD macros.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add code to handle case where board firmware does not start the
RTC.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix BCD value errors when month=9, moving the increment inside the
BIN2BCD macro.
Fix similar code for the weekday value, just for consistency.
This bug was reported by Michael Burian <dynmail1@gassner-waagen.at>.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix functions declared static and then implemented
without the static in drivers/i2c/chips.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eeprom_detect is first declared static and then when
the function is actually implemented, there is no static.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all remaining i2c bus and
chip drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New driver for the Xicor X1205 RTC chip.
Signed-off-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the .owner field for various struct xxxx_driver variables,
other than pci_driver.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DF_NOTIFY is an i2c_driver flag, using it as an i2c_client flag
doesn't make any sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop I2C_SMBUS_I2C_BLOCK_MAX, use I2C_SMBUS_BLOCK_MAX instead.
I2C_SMBUS_I2C_BLOCK_MAX has always been defined to the same value as
I2C_SMBUS_BLOCK_MAX, and this will never change: setting it to a lower
value would make no sense, setting it to a higher value would break
i2c_smbus_data compatibility. There is no point in changing
i2c_smbus_data to support larger block transactions in SMBus mode, as
no SMBus hardware supports more than 32 byte blocks. Thus, for larger
transactions, direct I2C transfers are the way to go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts kcalloc(1, ...) calls to use the new kzalloc() function.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
first one, so as to limit the risk that another command is issued on
the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
at least three times already, which proves how hard it is to get it
right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
as module parameters, virtually every i2c chip driver would need the
protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for kind-forced addresses to i2c_probe, like i2c_detect
has for (essentially) hardware monitoring drivers.
Note that this change will slightly increase the size of the drivers
using I2C_CLIENT_INSMOD, with no immediate benefit. This is a
requirement if we want to merge i2c_probe and i2c_detect though, and
seems a reasonable price to pay in comparison with the previous
cleanups which saved much more than that (such as the i2c-isa cleanup
or the i2c address ranges removal.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.
normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an unused local variable and change the subclient name.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the inline function kobj_to_i2c_client() from max6875.c to i2c.h.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an update to the max6875 driver.
It no longer does any detection, so the address must be forced on module load.
It only makes available the user EEPROM (read-only).
This patch is based off 2.6.13-rc2-mm2.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.
I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
DS1339 manual, page 6, chapter Date and time operation:
The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
hours register is defined as the 12-hour or 24-hour mode-select bit.
When high, the 12-hour mode is selected.
Patch below makes ds1337 driver work as documented in manual.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Part 2: Move the driver files themselves.
Note that the patch "adds trailing whitespace", because it does move the
files as-is, and some files happen to have trailing whitespace.
From: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Thu, Jun 30, 2005 at 11:47:09PM +0200, Sebastian Pigulak wrote:
> I've tried patching linux-2.6.13-RC1 with patch-2.6.13-rc1-git2 and
> building atxp1(it allows Vcore voltage changing) into the kernel.
> Unfortunately, the kernel compilation stops with:
>
> LD init/built-in.o
> LD vmlinux
> drivers/built-in.o(.text+0x92298): In function `atxp1_detect':
> : undefined reference to `i2c_which_vrm'
> drivers/built-in.o(.text+0x921ae): In function `atxp1_attach_adapter':
> : undefined reference to `i2c_detect'
> make: *** [vmlinux] B??d 1
> ==> ERROR: Build Failed. Aborting...
>
> Could someone have a look at the module and possibly fix it up?
SENSORS_ATXP1 must select I2C_SENSOR.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simple patch drops an out-of-date comment in the eeprom i2c chip
driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a simple path fixing an incorrect kfree in the m41t00 i2c chip
driver. The current code happens to work by accident, but the freed
pointer isn't the one which was allocated in the first place, which
could cause problems later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a proposed Kconfig update for the new max6875 i2c chip driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After a careful code analysis on the new max6875 driver
(drivers/i2c/chips/max6875.c), I have come to the conclusion that this
driver may cause EEPROM corruptions if used on random systems.
The EEPROM part of the MAX6875 chip is accessed using rather uncommon
I2C sequences. What is seen by the MAX6875 as reads can be seen by a
standard EEPROM (24C02) as writes. If you check the detection method
used by the driver, you'll find that the first SMBus command it will
send on the bus is i2c_smbus_write_byte_data(client, 0x80, 0x40). For
the MAX6875 it makes an internal pointer point to a specific offset of
the EEPROM waiting for a subsequent read command, so it's not an actual
data write operation, but for a standard EEPROM, this instead means
writing value 0x40 to offset 0x80. Blame Philips and Intel for the
obscure protocol.
Since the MAX6875 and the standard, common 24C02 EEPROMs share two I2C
addresses (0x50 and 0x52), loading the max6875 driver on a system with
standard EEPROMs at either address will trigger a write on these
EEPROMs, which will lead to their corruption if they happen not to be
write protected. This kind of EEPROMs can be found on memory modules
(SPD), ethernet adapters (MAC address), laptops (proprietary data) and
displays (EDID/DDC). Most of these are hopefully write-protected, but
not all of them.
For this reason, I would recommend that the max6875 driver be
neutralized, in a way that nobody can corrupt his/her EEPROMs by just
loading the driver. This means either deleting the driver completely, or
not listing any default address for it. I'd like this to be done before
2.6.13-rc1 is released.
Additionally, the max6875 driver lacks the 24RF08 corruption preventer
present in the eeprom driver, which means that loading this driver in a
system with such a chip would corrupt it as well.
Here is a proposed quick patch addressing the issue, although I wouldn't
mind a complete removal if it makes everyone feel safer. I think Ben
has plans to replace this driver by a much simplified one anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This includes various small cleanups and fixes to the TPS 6501x driver that
came mostly from review feedback by Jean Delvare; thanks Jean! Also some
goofy whitespace gets fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Wednesday 22 June 2005 08:17, Greg KH wrote:
> [PATCH] I2C: Coding style cleanups to via686a
>
> The via686a hardware monitoring driver has infamous coding style at the
> moment. I'd like to clean up the mess before I start working on other
> changes to this driver. Is the following patch acceptable? No code
> change, only coding style (indentation, alignments, trailing white
> space, a few parentheses and a typo).
>
> Signed-off-by: Jean Delvare <khali@linux-fr.org>
> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Nice.
You missed some. This one is on top of your patch:
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am using the atxp1 module to change vcore on my NForce2 via userspace
daemon (see punnoor.de).
Currently the atxp1 module will write to the log on every vcore change,
thus filling up my log - which I don't want. I am no kernel coder, but
I guess, this one-liner will change this behaviour in a wanted way, ie
output will be made for debug purposes only.
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the support for the W83697HF and W83627THF chips from
the w83781d driver. These chips have no I2C/SMBus interface and are
better supported by the Super-I/O-based w83627hf driver. Documentation
was updated to reflect the support drop.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for Maxim/Dallas DS1374 Real-Time Clock Chip
This change adds support for the Maxim/Dallas DS1374 RTC chip. This chip
is an I2C-based RTC that maintains a simple 32-bit binary seconds count
with battery backup support.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is an i2c driver for the Philips PCA9539 (16 bit I/O port).
It uses the new i2c-sysfs interfaces.
The patch includes documentation.
It depends on the patch that renames "i2c-sysfs.h" to "hwmon-sysfs.h"
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the new linux/i2c-sysfs.h header file to
linux/hwmon-sysfs.h. This names seems to be more appropriate since this
file defines macros and structures not related to i2c but to hardware
monitoring drivers. The patch also updates the five hardware monitoring
driver which include that header file already.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the MAX6875/MAX6874 chips.
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies the it87 hardware monitoring driver to take benefit
of the new sysfs callback features introduced by Yani Ioannou, making
the code much clearer and the resulting driver significantly smaller.
From: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I updated the lm63 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I updated the lm83 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I updated the lm90 hardware monitoring driver to take benefit of Yani
Ioannou's new sysfs callback capabilities.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I found a possible cleanup in the pcf8574 driver. We don't need to store
the read value in our private data structure, as we then never use it
again. I asked Aurelien and he is fine with the change. Please apply,
thanks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Following patch removes EXPERIMENTAL flag from some of I2C bus and chip
drivers. It is removed when the driver is in kernel at least from
2.6.3 and I generally think there is no problem with it.
Also this patch adds SiS 745 to help option of sis96x and it
also fixes nForce2 driver entry to reflect current state.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds an I2C driver for the TPS6501x series of power management chips.
It's used on many OMAP based boards, and this driver has been widely used
in the Linux-OMAP trees over the last year or so.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch kills another macro abuse in the via686a hardware monitoring
driver. Using a macro just to alias an array is quite useless, isn't it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are some corrections for drivers/i2c/chips/Kconfig.
Signed-off-by: Alexey Fisher <fishor@gmx.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes die_code from adm1021 as nothing within the
driver uses it.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The via686a hardware monitoring driver has infamous coding style at the
moment. I'd like to clean up the mess before I start working on other
changes to this driver. Is the following patch acceptable? No code
change, only coding style (indentation, alignments, trailing white
space, a few parentheses and a typo).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch kills a common macro abuse in i2c chip drivers: defining
ALARMS_FROM_REG returning its argument unchanged. Dropping the macro
makes the code somewhat more readable IMHO.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch includes jiffies.h in two i2c drivers.
(jiffies.h is needed for the time_after function.)
Signed-off-by: Dominik Hackl <dominik@hackl.dhs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an info print of detected VRM stolen from Sebastian
Witt's atxp1 sriver. ADM9240 already has vrm accessor removed.
Write no-op and whitespace fixes removed :)
Couple of comments changed, tested on 2.6.11.9.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This small patch changes two drivers, adm1025 and adm1026, to
report vid as cpu0_vid sysfs name as used by the other drivers.
Added duplicated names and six month warning for old names to
be removed as requested. Compile tested.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jarkko Lavinen provided patch to fix: "couldn't set the divisor 128
through fan1_div sysfs entry even though the chip supports it and
setting divisors 1..64 worked. This was due to POWER_TO_REG() only
checking 2's powers 0 till 5 but not 6."
This patch applies that fix to w83627hf and w83781d drivers.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In my cross-reference checking of sysfs names, the via686a needs
special case treatment as it the only driver expands S_IWUSR to
00200 with gcc -E. (00200 is the correct value for S_IWUSR).
This is caused by the driver including <linux/delay.h>, it compiles
fine without that header but I am unable to test drive the change.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This simple patch adds support for the SMSC LPC47M15x and LPC47M192
chips to the smsc47m1 hardware monitoring driver. These chips are
compatible with the other ones already supported by the driver, so I see
no reason not to support them, especially when the Linux 2.4 version of
the driver does already.
I also modified the info printks to name the chips by their real name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are the fixes for the bug you spotted in my new w83627ehf driver:
- Explicit division by 0.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a new hardware monitoring driver, w83627ehf, which supports the
Winbond W83627EHF Super-I/O chip. The driver is not complete, but
already usable. It only implements fan speed and temperature monitoring,
while the chip also supports voltage inputs with VID, PWM output and
temperature sensor selection. I have no more time to work on this, but
anyone with supported hardware could add the missing functionalities
later.
This driver is largely derived from the w83627hf driver.
Thanks to Leon Moonen and Steve Cliffe for tesing the preliminary
versions of my driver and reporting the problems they encountered.
Thanks to Grant Coady for noticing and fixing various corner cases in
the fan management. This third version of the driver hopefully addresses
all the issues the original version had.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Completion of Michiel Rook's port of adm9240 to 2.6 with addition
of auto fan clock divider based on Jean Delvare's algorithm, and
replaces scaling macros with static inlines.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Files that don't use CONFIG_* stuff shouldn't include config.h
Files that use CONFIG_* stuff should include config.h
It's that simple. ;-)
Signed-off-by: Alexey Dobriyan <adobriyan@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Wed, May 04, 2005 at 12:07:11PM +0200, Jean Delvare wrote:
> Additionally, I would welcome an additional patch documenting the fact
> that the ds1337 driver will work fine with the Dallas DS1339 real-time
> clock chip.
Document the fact that ds1337 driver works also with DS1339 real-time
clock chip.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Chip is searched by bus number rather than its own proprietary id.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_transfer returns number of sucessfully transfered messages. Change
error checking to accordingly. (ds1337_set_datetime never returned
sucess)
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make time format consistent with other RTC drivers.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_{dbg,err} functions should print client's device name. data->id can
be dropped from message, because device is determined by bus it hangs on
(it has fixed address).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use correct macros to convert between bdc and bin. See linux/bcd.h
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use i2c_transfer to send message, so we get proper bus locking.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for the Attansic ATXP1 I2C device, found on some x86
plattforms to change CPU and other voltages. Depends on the previous
i2c-vid.h patch.
Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some months ago, you killed the address ranges mechanism from all
sensors i2c chip drivers (both the module parameters and the in-code
address lists). I think it was a very good move, as the ranges can
easily be replaced by individual addresses, and this allowed for
significant cleanups in the i2c core (let alone the impressive size
shrink for all these drivers).
Unfortunately you did not do the same for non-sensors i2c chip drivers.
These need the address ranges even less, so we could get rid of the
ranges here as well for another significant i2c core cleanup. Here comes
a patch which does just that. Since the process is exactly the same as
what you did for the other drivers set already, I did not split this one
in parts.
A documentation update is included.
The change saves 308 bytes in the i2c core, and an average 1382 bytes
for chip drivers which use I2C_CLIENT_INSMOD, 126 bytes for those which
do not.
This change is required if we want to merge the sensors and non-sensors
i2c code (and we want to do this).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Index: gregkh-2.6/Documentation/i2c/writing-clients
===================================================================
Finally (phew!) this patch demonstrates how to adapt the adm1026 to
take advantage of the new callbacks, and the i2c-sysfs.h defined
structure/macros. Most of the other sensor/hwmon drivers could be
updated in the same way. The odd few exceptions (bmcsensors for
example) however might be better off with their own custom attribute
structure.
Signed-off-by: Yani Ioannou <yani.ioannou@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jörn Engel
Jean Delvare
Mark A. Greer
David Barksdale
Alessandro Zummo
Alexey Dobriyan
Ingo Molnar
Arjan van de Ven
Russell King
Greg Kroah-Hartman
Laurent Riffard
Nicolas Kaiser
Michael Burian
Linus Torvalds
Russell King
James Chapman
Ben Dooks
Deepak Saxena
Alessandro Zummo
Pekka Enberg
bgardner@wabtec.com
Ladislav Michl
Adrian Bunk
david-b@pacbell.net
Denis Vlasenko
Prakash Punnoor
Andrew Morton
Randy Vinson
R.Marek@sh.cvut.cz
Grant Coady
Dominik Hackl
Steven Cole
Alexey Dobriyan
Sebastian Witt
Clemens Koller
Yani Ioannou