New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=FxNN
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanups for the 4.8 cycle.
New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
Adding missing indio_dev->dev.of_node references to allow iio consumers
to access the device channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the pointer to the device tree node of the ADC so that iio
consumers can reference the respective channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds the necessary device tree binding to allow DT probing of
currently supported parts.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds basic driver implementation for Broadcom's
static adc controller used in iProc SoC's family.
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Lja
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
The driver supports MAX11644, MAX11645, MAX11646 and MAX11647 parts. But
the corresponding i2c_device_id are missing. Add them!
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add ACPI device ID matching for TI ADC081C/ADC101C/ADC121C ADCs.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently the ad7266 driver treats any failure to get vref as though the
regulator were not present but this means that if probe deferral is
triggered the driver will act as though the regulator were not present.
Instead only use the internal reference if we explicitly got -ENODEV which
is what is returned for absent regulators.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad7266 driver attempts to support deciding between the use of internal
and external power supplies by checking to see if an error is returned when
requesting the regulator. This doesn't work with the current code since the
driver uses a normal regulator_get() which is for non-optional supplies
and so assumes that if a regulator is not provided by the platform then
this is a bug in the platform integration and so substitutes a dummy
regulator. Use regulator_get_optional() instead which indicates to the
framework that the regulator may be absent and provides a dummy regulator
instead.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All regulator_get() variants return either a pointer to a regulator or an
ERR_PTR() so testing for NULL makes no sense and may lead to bugs if we
use NULL as a valid regulator. Fix this by using IS_ERR() as expected.
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Hq1a
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
Fix the code formatting to use the kernel preferred style
of using the actual variables to determize the size using
the sizeof() operator.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode and trying to lock it, but
left a gap where mode could change before the desired operation.
Use iio_device_claim_direct_mode() to guarantee device stays in
direct mode.
Refactor function to clarify look-up followed by lock sequence.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode and trying to lock it, but
left a gap where mode could change before the desired operation.
Use iio_device_claim_direct_mode() to guarantee device stays in
direct mode.
Refactor function to clarify look-up followed by lock sequence.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace the code that guarantees the device stays in direct mode
with iio_device_claim_direct_mode() which does same.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Driver was checking for direct mode but not locking it down.
Use iio_device_claim_direct_mode() to guarantee device stays
in direct mode.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add datasheet names for ADC channels to allow iio consumers access.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Nuvoton NAU7802 ADC is able to adjust its gain but prior knowledge of
its possible values was required to adjust it. Users had to guess the
possible gain values based on the ADC datasheet or on this driver's code.
This exposes the possible values in the in_voltage_scale_available file of
each nau7802 ADC device. The gain is set for the whole ADC and is therefore
not configurable by channel. Thus, there exists only one
in_voltage_scale_available file for each nau7802 ADC device even if it has
two separate channels.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
TI ADS1115 is a 16-bit resolution ADC that is register map
compatible with the ADS1015 device.
Signed-off-by: Matt Ranostay <matt.ranostay@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Disabling of the touchscreen IRQs should be done in
mxs_lradc_disable_ts. So disable only the masked virtual channels
in mxs_lradc_hw_stop and finally remove the unused function
mxs_lradc_irq_en_mask.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
After using devm_input_allocate_device for registration
the function mxs_lradc_ts_unregister isn't necessary anymore
since mxs_lradc_ts_close already does the job.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch simplifies the TS registration of mxs-lradc by
using devm_input_allocate_device.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zzV9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
This patch moves the STMP reset out of ADC init function so as to remove
the possiblity of an error return which will be necessary for PM ops support
patches to follow.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch moves the touchscreen type configuration into
a more suitable function. Btw this simplifies PM ops later.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set INPUT_PROP_DIRECT to indicate that it is a touchscreen on the
device to help userspace classify it.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Using this requires software triggers like CONFIG_IIO_HRTIMER_TRIGGER.
The device can be configured to do internal periodic sampling but does not
offer some sort of interrupt on data ready. Interrupts can only trigger when
values get out of a specific range.
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the errors reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: code indent should use tabs where possible
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: space prohibited before that ',' (ctx:WxW)
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the error reported by checkpatch.pl:
ERROR: switch and case should be at the same indent
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=j/qV
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.6 cycle.
This lot are either dependent on patches from the merge window or just came
in recently enough that they ended up in this tree.
* core
- The watermark for the buffers was given a value that meant that it was
impossible to actually set the watermark to anything sensible.
* at91_adc
- Fix a build config dependency on HAS_IOMEM
* bmc150
- Fix wrong output on big endian systems
* bmg160
- Fix wrong output on big endian systems
- Fix an issue in which the regmap return value was stored to the buffer
rather than the value actually being read in a bulk read.
* inv_mpu6050
- Fix an indirect build config dependency on HAS_IOMEM
* max30100
- Fix an error in fifo check condition that leads to a double read of the
final reading.
* st_magn
- Make sure ST_MAGN_TRIGGER_SET_STATE is always defined to avoid a build
error for relatively obscure config combinations.
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Bfg6
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.6a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into usb-linus
Jonathan writes:
First round of IIO fixes for the 4.6 cycle.
Again I've ended up with two early fix sets, depending on whether they are
dependent on elements of the merge window or simply came in after I had
patches with that dependency already, vs older fixes that were just too
late for the last cycle. This first set is for the older ones.
- max1353
* Add a missing adc to max1363_id - the driver has supported the
max11644-11647 for a while, but as they weren't in the id table there
was no way of actually initializing it.
* Fix a wrong reference voltage for the above models. Given you couldn't
initialize the driver for these parts without patching, no one noticed
that the reference voltage used in computing the scaling was wrong.
- apds9960
* The fifo last enelement was read twice (and hence pushed out twice) due
to a small logic bug.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXAYogAAoJEFSFNJnE9BaIhtsQAK9hsojCFC4EmcE0LdlC7A6r
h/Any+ehurHSQIZmAZ1mn8QDBedf6Afpj+jl/qt/DADQk3e3u+TO1TbVHHUDB8Na
ynvt1eibnUPAKxjbetUnPfOTaksp2GN8oScjPqk/3xmP1ip/uP3l2DM+jBOspW2K
44UDpKE/aeulyCeG8wBHLY0ySuipQ8ZJyebETM3E94UrNdMHiuMyRA+SEbhcG+0T
GyHYrlmPScFlk3xlhuYk7kS6gJQG0xg6u/qyuaBlQMKY1KXMGknU8sxSmqxRmCNn
pJ3MeHZY6hFe3PNTgd30z+xbXN4JAifyUBHT2foRF86+f0BJSNIZJo/ynfCPli4z
Rl+4M9NziYxw4V6osjKtPBquvk8UV6G/1tcgrr5pNFJor4dk6xRg/xCotYsqZuMX
ypWOMuvkPQq+mqf68uJYlE++/A3xHP7aHdOlsXMgM8605KH1aSecbUP2dhRbHdRs
u8XTt8Xj6uumQnxUnKjDZGIsDaxyw5JwarjhiNdJaCRgAgFw2qmNiFWYNkBaxxOt
BheQBceoHLHDk/qTDsi0b5KDLqvArrbY8L6WBR+gW21isFpho5VDMgBSfNfdObGB
nYaYTBcdx6sXm1SC1bMwVcgMnd3Bs4eWJRw79VFz/pFtTOc5Xpj4uVvnNCzuomqb
MygKzQb48Gx23saBy4Za
=SgQo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.7 cycle.
New core support
* UV light modifier (for intensity)
* UV light index channel type.
New device support
* hp206c barometer and altimeter
- new driver.
* mcp4131 potentiometer
- new driver supporting lots of parts from Microchip.
* mma8452
- FXLS8471Q support
- NXP LPC18XX SOC ADC
- new driver.
- NXP LPC18XX SOC DAC
- new driver.
- rockchip_saradc
- support rk3399
* st accel
- h3lis331dl support
Staging driver removals
* adis16204
- obsolete part making it hard to get parts to test the driver in order
to clean it up.
* adis16220
- obsolete part making it hard to get the parts test the driver in order
to clean it up.
Features
* core
- convenience functions to claim / release direct access to the device.
Makes more consistent handling of this corner easier. Used in ad7192 driver.
* ak8975
- power regulator support.
* at91-sama5d2
- differential channel support.
* mma8452
- runtime pm support
- drop device specific autosleep and use the runtime pm one instead.
* ms5611
- DT bindings
- oversampling ratio support
Cleanups and minor fixes
* MAINTAINERS
- Peter got married - hence name change!
* Documentation
- Fix a typo in in_proximity_raw description.
- Add some missing docs for iio_buffer_access_funcs.
* Tools
- update iio_event_monitor names to match new stuff.
- make generic_buffer look for triggers ending in -trigger as we let these in
for a number of drivers a long time back and now it is a fairly common
option.
Drivers
* staging wide
- convert bare unsigned usage to unsigned int to comply with coding style.
* non staging wide:
- since boiler plate gpio handling of interrupts has been moved into the
ACPI core we don't need to include gpio/consumer.h in a load of drivers so
drop it.
* ad7606
- fix an endian casting sparse warning.
* ak8975
- fix a possible unitialized warning from gcc.
- drop and unused field left over from earlier cleanups
- fix a missing regulator_disable on exit.
* at91-sama5d2
- typo and indentation
- missing IOMEM dependency.
- cleanup mode register usage by avoidling erasing whole thing when changing
the sampling frequency.
* bmc150
- use the core demux and available_scan_masks to simplify buffer handling
- optimize the transfers in the trigger handler now we have a magic function
to emulate bulk reads (under circumstances met here). This matters with some
rather dumb i2c adapters in particular.
- use a single regmap_conf for all bus types as they were all the same.
* bmg160
- use the core demux and available_scan_masks to simplify the buffer handling
- optimize the transfers in the trigger handler now we have a magic funciton
to emulate bulk rads (under circumstances met here).
- drop gpio interrupt probing from the driver (ACPI) as now handled by the
ACPI core.
* ina2xx-adc
- update the CALIB register when RShunt changes.
- fix scale for VShunt - in reality this error canceled out when used.
* isl29028
- use regmap to retrieve the struct device instead of carrying a second
copy of it around.
* kxcjk-1013
- use core demux
- optimize i2c transfers in the trigger handler.
* mcp4531
- refactor to use a pointer to access model parameters instead of indexing
into the array each time.
* mma8452
- style fixes
- avoid swtiching to active whenever the config changes
- add missin i2c_device_id for mma8451
* mpu6050
- fix possible NULL dereference.
- fix the name / chip_id used when ACPI used (otherwise reports as NULL).
* ms5611
- fix a missing regulator_disable that left the regulator on during removal.
* mxc4005
- drop gpio interrupt handling for ACPI case from driver as the core now
handles this case.
* st-sensors
- note that there are only ever a maximum of 3 axis on current st-sensors
so just allocate a fixed sized buffer big enough for that.
* tpl0102
- change the i2c_check_functionality condition to bring it inline with other
IIO users as EOPNOTSUPP.
* tsl2563
- replace deprecated flush_scheduled_work
The scale would result in uV instead of expected mV.
Mostly cosmetic, since the value of 'Power' was computed OK.
Signed-off-by: Marc Titinger <marc.titinger@baylibre.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add signed differential channels and update the voltage scale for
differential conversions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Do not erase previous configuration of the mode register when setting
the sampling frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devres.o gets linked if HAS_IOMEM is present so on ARCH=um
allyesconfig (COMPILE_TEST) failed with:
drivers/built-in.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x48f548): undefined reference to `devm_ioremap_resource'
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Greg Kroah-Hartman
Matt Ranostay
Florian Vaussard
Raveendra Padasalagi
Gregor Boirie
Dan O'Donovan
Mark Brown
Andrew F. Davis
Alison Schofield
Matt Ranostay
Quentin Schulz
Stefan Wahren
Marek Vasut
Ksenija Stanojevic
Crestez Dan Leonard
Slawomir Stepien
Marc Titinger
Ludovic Desroches
Krzysztof Kozlowski