Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also spur channel count and range is different for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper function would be used for AR9485.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Have it in ah->caps. This will be used during various
calibrations.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 is a single chain and single band (2.4 Ghz) chip.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar9300RateSize is not necessarily a power of 4.
Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.
ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ath_printk and ath_<level> similar to
dev_printk and dev_<level> from device.h
This allows a more gradual rename of ath_print
to to ath_dbg or perhaps ath_debug.
This basically removes debug.h leaving
only an #define ath_printk ath_dbg
there and moving all the ATH_DBG_<foo>
enums to ath.h
I do not think there's much purpose for struct
ath_common * being passed to the ath_printk
functions, but perhaps there might be.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 uses pm_qos (/dev/network_latency) in order to determine the
dynamic ps timeout (or disable the dynamic-ps at all in some cases).
commit ff616381 added a comparison for the current network_latency
against one high value (1900ms), and against the default value
(2000sec, rather than the commented 2sec).
however, the representation of 1900ms was incorrect:
1900ms = 1900000us ( != 1900000000 )
fix it by using USEC_TO_MSEC/SEC consts.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The card doesn't support MFP, so silently accept DISABLED and OPTIONAL
settings.
This avoids the following failure in wpa_supplicant logs:
State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
wpa_driver_wext_associate: assoc failed because set_auth_param(IW_AUTH_MFP) failed
Association request to the driver failed
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.
This uses the recently added generic EWMA library function.
--
v2: fix ABI breakage and change factor to be a power of 2.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call netif_napi_{add,del}() on the NAPI contexts in the new and
old channels, respectively.
Since efx_init_napi() cannot fail, make its return type void.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we are using a legacy interrupt, our IRQ may be shared and our
interrupt handler may be called even though interrupts are disabled on
the NIC. When we change ring sizes, we reallocate the event queue and
the interrupt handler may use an invalid pointer when called for
another device's interrupt.
Maintain a legacy_irq_enabled flag and test that at the top of the
interrupt handler. Note that this problem results from the need to
work around broken INT_ISR0 reads, and does not affect the legacy
interrupt handler for Falcon A1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move search_depth arrays into per-table state.
Define initialisation function efx_filter_init_rx() which sets
everything apart from the match fields.
Define efx_filter_set_{ipv4_local,ipv4_full,eth_local}() to set the
match fields. This allows some simplification of callers and later
support for additional protocols and more flexible matching using
multiple calls to these functions.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The separation between filter tables is largely an internal detail
and it may be removed in future hardware. To prepare for that:
- Merge table ID with filter index to make an opaque filter ID
- Wrap efx_filter_table_clear() with a function that clears filters
from both RX tables, which is all that the current caller requires
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add message at start of self-test and increase log level of message at
end of self-test, so that any other messages produced during the
test are clearly associated with it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Ensure that cmsg->cmsg_type value is valid for qpolicy
that is currently in use.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Whenever we add DMA descriptors to a TX ring and update the ring
pointer, the TX DMA engine must first read the new DMA descriptors and
then start reading packet data. However, all released Solarflare 10G
controllers have a 'TX push' feature that allows us to reduce latency
by writing the first new DMA descriptor along with the pointer update.
This is only useful when the queue is empty. The hardware should
ignore the pushed descriptor if the queue is not empty, but this check
is buggy, so we must do it in software.
In order to tell whether a TX queue is empty, we need to compare the
previous transmission count (write_count) and completion count
(read_count). However, if we do that every time we update the ring
pointer then read_count may ping-pong between the caches of two CPUs
running the transmission and completion paths for the queue.
Therefore, we split the check for an empty queue between the
completion path and the transmission path:
- Add an empty_read_count field representing a point at which the
completion path saw the TX queue as empty.
- Add an old_write_count field for use on the completion path.
- On the completion path, whenever read_count reaches or passes
old_write_count the TX queue may be empty. We then read
write_count, set empty_read_count if read_count == write_count,
and update old_write_count.
- On the transmission path, we read empty_read_count. If it's set, we
compare it with the value of write_count before the current set of
descriptors was added. If they match, the queue really is empty and
we can use TX push.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
It is not necessary to serialise writes to the paged 128-bit
registers. However, if we don't then we must always write the last
dword separately, not as part of a qword write.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Document exactly which registers and functions have special behaviour,
and why races on writes to descriptor pointers are safe.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Vasanthakumar Thiagarajan
John W. Linville
Joe Perches
Eliad Peller
David Kilroy
Bruno Randolf
Ben Hutchings
Rajkumar Manoharan
Senthil Balasubramanian
Felix Fietkau
Matteo Croce
Tomasz Grobelny
David S. Miller