commit 6e0fdf9af2 upstream.
Commit b0d278b7d3 ("powerpc/perf_event: Reduce latency of calling
perf_event_do_pending") added a check for CONFIG_PMAC were a check for
CONFIG_PPC_PMAC was clearly intended.
Fixes: b0d278b7d3 ("powerpc/perf_event: Reduce latency of calling perf_event_do_pending")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d73320a96 upstream.
commit 8f9c0119d7 (compat: fs: Generic compat_sys_sendfile
implementation) changed the PowerPC 64bit sendfile call from
sys_sendile64 to sys_sendfile.
Unfortunately this broke sendfile of lengths greater than 2G because
sys_sendfile caps at MAX_NON_LFS. Restore what we had previously which
fixes the bug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4cad90f9e upstream.
We had a mix & match of flags used when creating legacy ports
depending on where we found them in the device-tree. Among others
we were missing UPF_SKIP_TEST for some kind of ISA ports which is
a problem as quite a few UARTs out there don't support the loopback
test (such as a lot of BMCs).
Let's pick the set of flags used by the SoC code and generalize it
which means autoconf, no loopback test, irq maybe shared and fixed
port.
Sending to stable as the lack of UPF_SKIP_TEST is breaking
serial on some machines so I want this back into distros
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09567e7fd4 upstream.
We have a bug in our hugepage handling which exhibits as an infinite
loop of hash faults. If the fault is being taken in the kernel it will
typically trigger the softlockup detector, or the RCU stall detector.
The bug is as follows:
1. mmap(0xa0000000, ..., MAP_FIXED | MAP_HUGE_TLB | MAP_ANONYMOUS ..)
2. Slice code converts the slice psize to 16M.
3. The code on lines 539-540 of slice.c in slice_get_unmapped_area()
synchronises the mm->context with the paca->context. So the paca slice
mask is updated to include the 16M slice.
3. Either:
* mmap() fails because there are no huge pages available.
* mmap() succeeds and the mapping is then munmapped.
In both cases the slice psize remains at 16M in both the paca & mm.
4. mmap(0xa0000000, ..., MAP_FIXED | MAP_ANONYMOUS ..)
5. The slice psize is converted back to 64K. Because of the check on line 539
of slice.c we DO NOT update the paca->context. The paca slice mask is now
out of sync with the mm slice mask.
6. User/kernel accesses 0xa0000000.
7. The SLB miss handler slb_allocate_realmode() **uses the paca slice mask**
to create an SLB entry and inserts it in the SLB.
18. With the 16M SLB entry in place the hardware does a hash lookup, no entry
is found so a data access exception is generated.
19. The data access handler calls do_page_fault() -> handle_mm_fault().
10. __handle_mm_fault() creates a THP mapping with do_huge_pmd_anonymous_page().
11. The hardware retries the access, there is still nothing in the hash table
so once again a data access exception is generated.
12. hash_page() calls into __hash_page_thp() and inserts a mapping in the
hash. Although the THP mapping maps 16M the hashing is done using 64K
as the segment page size.
13. hash_page() returns immediately after calling __hash_page_thp(), skipping
over the code at line 1125. Resulting in the mismatch between the
paca->context and mm->context not being detected.
14. The hardware retries the access, the hash it generates using the 16M
SLB entry does NOT match the hash we inserted.
15. We take another data access and go into __hash_page_thp().
16. We see a valid entry in the hpte_slot_array and so we call updatepp()
which succeeds.
17. Goto 14.
We could fix this in two ways. The first would be to remove or modify
the check on line 539 of slice.c.
The second option is to cause the check of paca psize in hash_page() on
line 1125 to also be done for THP pages.
We prefer the latter, because the check & update of the paca psize is
not done until we know it's necessary. It's also done only on the
current cpu, so we don't need to IPI all other cpus.
Without further rearranging the code, the simplest fix is to pull out
the code that checks paca psize and call it in two places. Firstly for
THP/hugetlb, and secondly for other mappings as before.
Thanks to Dave Jones for trinity, which originally found this bug.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54f112a383 upstream.
In pseries_eeh_get_state(), EEH_STATE_UNAVAILABLE is always
overwritten by EEH_STATE_NOT_SUPPORT because of the missed
"break" there. The patch fixes the issue.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18dd78c427 upstream.
NFS_INO_INVALID_DATA cannot be ignored, even if we have a delegation.
We're still having some problems with data corruption when multiple
clients are appending to a file and those clients are being granted
write delegations on open.
To reproduce:
Client A:
vi /mnt/`hostname -s`
while :; do echo "XXXXXXXXXXXXXXX" >>/mnt/file; sleep $(( $RANDOM % 5 )); done
Client B:
vi /mnt/`hostname -s`
while :; do echo "YYYYYYYYYYYYYYY" >>/mnt/file; sleep $(( $RANDOM % 5 )); done
What's happening is that in nfs_update_inode() we're recognizing that
the file size has changed and we're setting NFS_INO_INVALID_DATA
accordingly, but then we ignore the cache_validity flags in
nfs_write_pageuptodate() because we have a delegation. As a result,
in nfs_updatepage() we're extending the write to cover the full page
even though we've not read in the data to begin with.
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a914722f33 upstream.
Otherwise the kernel oopses when remounting with IPv6 server because
net is dereferenced in dev_get_by_name.
Use net ns of current thread so that dev_get_by_name does not operate on
foreign ns. Changing the address is prohibited anyway so this should not
affect anything.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com>
Cc: linux-nfs@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit abbec2da13 upstream.
The addition of lockdep code to write_seqcount_begin/end has lead to
a bunch of false positive claims of ABBA deadlocks with the so_lock
spinlock. Audits show that this simply cannot happen because the
read side code does not spin while holding so_lock.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43b6535e71 upstream.
Fix a bug, whereby nfs_update_inode() was declaring the inode to be
up to date despite not having checked all the attributes.
The bug occurs because the temporary variable in which we cache
the validity information is 'sanitised' before reapplying to
nfsi->cache_validity.
Reported-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12337901d6 upstream.
Note nobody's ever noticed because the typical client probably never
requests FILES_AVAIL without also requesting something else on the list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c789102c20 upstream.
If the accept() call fails, we need to put the module reference.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60e1751cb5 upstream.
Avoid that closing /dev/infiniband/umad<n> or /dev/infiniband/issm<n>
triggers a use-after-free. __fput() invokes f_op->release() before it
invokes cdev_put(). Make sure that the ib_umad_device structure is
freed by the cdev_put() call instead of f_op->release(). This avoids
that changing the port mode from IB into Ethernet and back to IB
followed by restarting opensmd triggers the following kernel oops:
general protection fault: 0000 [#1] PREEMPT SMP
RIP: 0010:[<ffffffff810cc65c>] [<ffffffff810cc65c>] module_put+0x2c/0x170
Call Trace:
[<ffffffff81190f20>] cdev_put+0x20/0x30
[<ffffffff8118e2ce>] __fput+0x1ae/0x1f0
[<ffffffff8118e35e>] ____fput+0xe/0x10
[<ffffffff810723bc>] task_work_run+0xac/0xe0
[<ffffffff81002a9f>] do_notify_resume+0x9f/0xc0
[<ffffffff814b8398>] int_signal+0x12/0x17
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=75051
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8ec0a0e6b5 upstream.
Avoid leaking a kref count in ib_umad_open() if port->ib_dev == NULL
or if nonseekable_open() fails.
Avoid leaking a kref count, that sm_sem is kept down and also that the
IB_PORT_SM capability mask is not cleared in ib_umad_sm_open() if
nonseekable_open() fails.
Since container_of() never returns NULL, remove the code that tests
whether container_of() returns NULL.
Moving the kref_get() call from the start of ib_umad_*open() to the
end is safe since it is the responsibility of the caller of these
functions to ensure that the cdev pointer remains valid until at least
when these functions return.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ydroneaud@opteya.com: rework a bit to reduce the amount of code changed]
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
[ nonseekable_open() can't actually fail, but.... - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 024ca90151 upstream.
Avoid that the loops that iterate over the request ring can encounter
a pointer to a SCSI command in req->scmnd that is no longer associated
with that request. If the function srp_unmap_data() is invoked twice
for a SCSI command that is not in flight then that would cause
ib_fmr_pool_unmap() to be invoked with an invalid pointer as argument,
resulting in a kernel oops.
Reported-by: Sagi Grimberg <sagig@mellanox.com>
Reference: http://thread.gmane.org/gmane.linux.drivers.rdma/19068/focus=19069
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e6d3e5c70 upstream.
This patch addresses an issue where the legacy diagpacket is sent in
from the user, but the driver operates on only the extended
diagpkt. This patch specifically initializes the extended diagpkt
based on the legacy packet.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 911eccd284 upstream.
The code used a literal 1 in dispatching an IB_EVENT_PKEY_CHANGE.
As of the dual port qib QDR card, this is not necessarily correct.
Change to use the port as specified in the call.
Reported-by: Alex Estrin <alex.estrin@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 43bc889380 upstream.
The i386 ABI disagrees with most other ABIs regarding alignment of
data type larger than 4 bytes: on most ABIs a padding must be added at
end of the structures, while it is not required on i386.
So for most ABIs struct mlx5_ib_create_srq gets implicitly padded to be
aligned on a 8 bytes multiple, while for i386, such padding is not
added.
Tool pahole could be used to find such implicit padding:
$ pahole --anon_include \
--nested_anon_include \
--recursive \
--class_name mlx5_ib_create_srq \
drivers/infiniband/hw/mlx5/mlx5_ib.o
Then, structure layout can be compared between i386 and x86_64:
# +++ obj-i386/drivers/infiniband/hw/mlx5/mlx5_ib.o.pahole.txt 2014-03-28 11:43:07.386413682 +0100
# --- obj-x86_64/drivers/infiniband/hw/mlx5/mlx5_ib.o.pahole.txt 2014-03-27 13:06:17.788472721 +0100
# @@ -69,7 +68,6 @@ struct mlx5_ib_create_srq {
# __u64 db_addr; /* 8 8 */
# __u32 flags; /* 16 4 */
#
# - /* size: 20, cachelines: 1, members: 3 */
# - /* last cacheline: 20 bytes */
# + /* size: 24, cachelines: 1, members: 3 */
# + /* padding: 4 */
# + /* last cacheline: 24 bytes */
# };
ABI disagreement will make an x86_64 kernel try to read past
the buffer provided by an i386 binary.
When boundary check will be implemented, the x86_64 kernel will
refuse to read past the i386 userspace provided buffer and the
uverb will fail.
Anyway, if the structure lay in memory on a page boundary and
next page is not mapped, ib_copy_from_udata() will fail and the
uverb will fail.
This patch makes create_srq_user() takes care of the input
data size to handle the case where no padding was provided.
This way, x86_64 kernel will be able to handle struct mlx5_ib_create_srq
as sent by unpatched and patched i386 libmlx5.
Link: http://marc.info/?i=cover.1399309513.git.ydroneaud@opteya.com
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapter")
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a8237b32a3 upstream.
The i386 ABI disagrees with most other ABIs regarding alignment of
data type larger than 4 bytes: on most ABIs a padding must be added at
end of the structures, while it is not required on i386.
So for most ABI struct mlx5_ib_create_cq get padded to be aligned on a
8 bytes multiple, while for i386, such padding is not added.
The tool pahole can be used to find such implicit padding:
$ pahole --anon_include \
--nested_anon_include \
--recursive \
--class_name mlx5_ib_create_cq \
drivers/infiniband/hw/mlx5/mlx5_ib.o
Then, structure layout can be compared between i386 and x86_64:
# +++ obj-i386/drivers/infiniband/hw/mlx5/mlx5_ib.o.pahole.txt 2014-03-28 11:43:07.386413682 +0100
# --- obj-x86_64/drivers/infiniband/hw/mlx5/mlx5_ib.o.pahole.txt 2014-03-27 13:06:17.788472721 +0100
# @@ -34,9 +34,8 @@ struct mlx5_ib_create_cq {
# __u64 db_addr; /* 8 8 */
# __u32 cqe_size; /* 16 4 */
#
# - /* size: 20, cachelines: 1, members: 3 */
# - /* last cacheline: 20 bytes */
# + /* size: 24, cachelines: 1, members: 3 */
# + /* padding: 4 */
# + /* last cacheline: 24 bytes */
# };
This ABI disagreement will make an x86_64 kernel try to read past the
buffer provided by an i386 binary.
When boundary check will be implemented, a x86_64 kernel will refuse
to read past the i386 userspace provided buffer and the uverb will
fail.
Anyway, if the structure lies in memory on a page boundary and next
page is not mapped, ib_copy_from_udata() will fail when trying to read
the 4 bytes of padding and the uverb will fail.
This patch makes create_cq_user() takes care of the input data size to
handle the case where no padding is provided.
This way, x86_64 kernel will be able to handle struct
mlx5_ib_create_cq as sent by unpatched and patched i386 libmlx5.
Link: http://marc.info/?i=cover.1399309513.git.ydroneaud@opteya.com
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapter")
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde92cf455 upstream.
Peter Wu noticed the following splat on his machine when updating
/proc/sys/kernel/watchdog_thresh:
BUG: sleeping function called from invalid context at mm/slub.c:965
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: init
3 locks held by init/1:
#0: (sb_writers#3){.+.+.+}, at: [<ffffffff8117b663>] vfs_write+0x143/0x180
#1: (watchdog_proc_mutex){+.+.+.}, at: [<ffffffff810e02d3>] proc_dowatchdog+0x33/0x110
#2: (cpu_hotplug.lock){.+.+.+}, at: [<ffffffff810589c2>] get_online_cpus+0x32/0x80
Preemption disabled at:[<ffffffff810e0384>] proc_dowatchdog+0xe4/0x110
CPU: 0 PID: 1 Comm: init Not tainted 3.16.0-rc1-testing #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x4e/0x7a
__might_sleep+0x11d/0x190
kmem_cache_alloc_trace+0x4e/0x1e0
perf_event_alloc+0x55/0x440
perf_event_create_kernel_counter+0x26/0xe0
watchdog_nmi_enable+0x75/0x140
update_timers_all_cpus+0x53/0xa0
proc_dowatchdog+0xe4/0x110
proc_sys_call_handler+0xb3/0xc0
proc_sys_write+0x14/0x20
vfs_write+0xad/0x180
SyS_write+0x49/0xb0
system_call_fastpath+0x16/0x1b
NMI watchdog: disabled (cpu0): hardware events not enabled
What happened is after updating the watchdog_thresh, the lockup detector
is restarted to utilize the new value. Part of this process involved
disabling preemption. Once preemption was disabled, perf tried to
allocate a new event (as part of the restart). This caused the above
BUG_ON as you can't sleep with preemption disabled.
The preemption restriction seemed agressive as we are not doing anything
on that particular cpu, but with all the online cpus (which are
protected by the get_online_cpus lock). Remove the restriction and the
BUG_ON goes away.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9e0436b30 upstream.
Use the prescaler index, rather than its value, to configure the watchdog.
This will prevent a mismatch with the prescaler used to calculate the cycles.
Signed-off-by: Per Gundberg <per.gundberg@icomera.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23afeb613e upstream.
On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.
The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.
Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 938626d96a upstream.
Implementation of ->set_timeout() is supposed to set 'timeout' field of 'struct
watchdog_device' passed to it. sp805 was rather setting this in a local
variable. Fix it.
Reported-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72abc8f4b4 upstream.
I hit the same assert failed as Dolev Raviv reported in Kernel v3.10
shows like this:
[ 9641.164028] UBIFS assert failed in shrink_tnc at 131 (pid 13297)
[ 9641.234078] CPU: 1 PID: 13297 Comm: mmap.test Tainted: G O 3.10.40 #1
[ 9641.234116] [<c0011a6c>] (unwind_backtrace+0x0/0x12c) from [<c000d0b0>] (show_stack+0x20/0x24)
[ 9641.234137] [<c000d0b0>] (show_stack+0x20/0x24) from [<c0311134>] (dump_stack+0x20/0x28)
[ 9641.234188] [<c0311134>] (dump_stack+0x20/0x28) from [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs])
[ 9641.234265] [<bf22425c>] (shrink_tnc_trees+0x25c/0x350 [ubifs]) from [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs])
[ 9641.234307] [<bf2245ac>] (ubifs_shrinker+0x25c/0x310 [ubifs]) from [<c00cdad8>] (shrink_slab+0x1d4/0x2f8)
[ 9641.234327] [<c00cdad8>] (shrink_slab+0x1d4/0x2f8) from [<c00d03d0>] (do_try_to_free_pages+0x300/0x544)
[ 9641.234344] [<c00d03d0>] (do_try_to_free_pages+0x300/0x544) from [<c00d0a44>] (try_to_free_pages+0x2d0/0x398)
[ 9641.234363] [<c00d0a44>] (try_to_free_pages+0x2d0/0x398) from [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8)
[ 9641.234382] [<c00c6a60>] (__alloc_pages_nodemask+0x494/0x7e8) from [<c00f62d8>] (new_slab+0x78/0x238)
[ 9641.234400] [<c00f62d8>] (new_slab+0x78/0x238) from [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c)
[ 9641.234419] [<c031081c>] (__slab_alloc.constprop.42+0x1a4/0x50c) from [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188)
[ 9641.234459] [<c00f80e8>] (kmem_cache_alloc_trace+0x54/0x188) from [<bf227908>] (do_readpage+0x168/0x468 [ubifs])
[ 9641.234553] [<bf227908>] (do_readpage+0x168/0x468 [ubifs]) from [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs])
[ 9641.234606] [<bf2296a0>] (ubifs_readpage+0x424/0x464 [ubifs]) from [<c00c17c0>] (filemap_fault+0x304/0x418)
[ 9641.234638] [<c00c17c0>] (filemap_fault+0x304/0x418) from [<c00de694>] (__do_fault+0xd4/0x530)
[ 9641.234665] [<c00de694>] (__do_fault+0xd4/0x530) from [<c00e10c0>] (handle_pte_fault+0x480/0xf54)
[ 9641.234690] [<c00e10c0>] (handle_pte_fault+0x480/0xf54) from [<c00e2bf8>] (handle_mm_fault+0x140/0x184)
[ 9641.234716] [<c00e2bf8>] (handle_mm_fault+0x140/0x184) from [<c0316688>] (do_page_fault+0x150/0x3ac)
[ 9641.234737] [<c0316688>] (do_page_fault+0x150/0x3ac) from [<c000842c>] (do_DataAbort+0x3c/0xa0)
[ 9641.234759] [<c000842c>] (do_DataAbort+0x3c/0xa0) from [<c0314e38>] (__dabt_usr+0x38/0x40)
After analyzing the code, I found a condition that may cause this failed
in correct operations. Thus, I think this assertion is wrong and should be
removed.
Suppose there are two clean znodes and one dirty znode in TNC. So the
per-filesystem atomic_t @clean_zn_cnt is (2). If commit start, dirty_znode
is set to COW_ZNODE in get_znodes_to_commit() in case of potentially ops
on this znode. We clear COW bit and DIRTY bit in write_index() without
@tnc_mutex locked. We don't increase @clean_zn_cnt in this place. As the
comments in write_index() shows, if another process hold @tnc_mutex and
dirty this znode after we clean it, @clean_zn_cnt would be decreased to (1).
We will increase @clean_zn_cnt to (2) with @tnc_mutex locked in
free_obsolete_znodes() to keep it right.
If shrink_tnc() performs between decrease and increase, it will release
other 2 clean znodes it holds and found @clean_zn_cnt is less than zero
(1 - 2 = -1), then hit the assertion. Because free_obsolete_znodes() will
soon correct @clean_zn_cnt and no harm to fs in this case, I think this
assertion could be removed.
2 clean zondes and 1 dirty znode, @clean_zn_cnt == 2
Thread A (commit) Thread B (write or others) Thread C (shrinker)
->write_index
->clear_bit(DIRTY_NODE)
->clear_bit(COW_ZNODE)
@clean_zn_cnt == 2
->mutex_locked(&tnc_mutex)
->dirty_cow_znode
->!ubifs_zn_cow(znode)
->!test_and_set_bit(DIRTY_NODE)
->atomic_dec(&clean_zn_cnt)
->mutex_unlocked(&tnc_mutex)
@clean_zn_cnt == 1
->mutex_locked(&tnc_mutex)
->shrink_tnc
->destroy_tnc_subtree
->atomic_sub(&clean_zn_cnt, 2)
->ubifs_assert <- hit
->mutex_unlocked(&tnc_mutex)
@clean_zn_cnt == -1
->mutex_lock(&tnc_mutex)
->free_obsolete_znodes
->atomic_inc(&clean_zn_cnt)
->mutux_unlock(&tnc_mutex)
@clean_zn_cnt == 0 (correct after shrink)
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 691a7c6f28 upstream.
There is a race condition in UBIFS:
Thread A (mmap) Thread B (fsync)
->__do_fault ->write_cache_pages
-> ubifs_vm_page_mkwrite
-> budget_space
-> lock_page
-> release/convert_page_budget
-> SetPagePrivate
-> TestSetPageDirty
-> unlock_page
-> lock_page
-> TestClearPageDirty
-> ubifs_writepage
-> do_writepage
-> release_budget
-> ClearPagePrivate
-> unlock_page
-> !(ret & VM_FAULT_LOCKED)
-> lock_page
-> set_page_dirty
-> ubifs_set_page_dirty
-> TestSetPageDirty (set page dirty without budgeting)
-> unlock_page
This leads to situation where we have a diry page but no budget allocated for
this page, so further write-back may fail with -ENOSPC.
In this fix we return from page_mkwrite without performing unlock_page. We
return VM_FAULT_LOCKED instead. After doing this, the race above will not
happen.
Signed-off-by: hujianyang <hujianyang@huawei.com>
Tested-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ab6c15bc66 upstream.
Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:
CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c
Kernel panic - not syncing: Attempted to kill the idle task!
This patch fixes the problem
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91ad11d7cc upstream.
On MIPS calls to _mcount in modules generate 2 instructions to load
the _mcount address (and therefore 2 relocations). The mcount_loc
table should only reference the first of these, so the second is
filtered out by checking the relocation offset and ignoring ones that
immediately follow the previous one seen.
However if a module has an _mcount call at offset 0, the second
relocation would not be filtered out due to old_r_offset == 0
being taken to mean that the current relocation is the first one
seen, and both would end up in the mcount_loc table.
This results in ftrace_make_nop() patching both (adjacent)
instructions to branches over the _mcount call sequence like so:
0xffffffffc08a8000: 04 00 00 10 b 0xffffffffc08a8014
0xffffffffc08a8004: 04 00 00 10 b 0xffffffffc08a8018
0xffffffffc08a8008: 2d 08 e0 03 move at,ra
...
The second branch is in the delay slot of the first, which is
defined to be unpredictable - on the platform on which this bug was
encountered, it triggers a reserved instruction exception.
Fix by initializing old_r_offset to ~0 and using that instead of 0
to determine whether the current relocation is the first seen.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7098/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af5ded8ccf upstream.
In module exit, dfs_parent and it's subtree were removed before
unregistering with pci. When debugfs entry for each device is attempted
to remove in pci_remove() context, they don't exist, as dfs_parent and
its children were already ripped apart.
Modified to first unregister with pci and then remove dfs_parent.
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1e714db81 upstream.
A hardware quirk in P320h/P420m interfere with PCIe transactions on some
AMD chipsets, making P320h/P420m unusable. This workaround is to disable
ERO and NoSnoop bits in the parent and root complex for normal
functioning of these devices
NOTE: This workaround is specific to AMD chipset with a PCIe upstream
device with device id 0x5aXX
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Sam Bradshaw <sbradshaw@micron.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67ebd8140d upstream.
3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
added the "flags & PCI_VGA_STATE_CHANGE_DECODES" condition to an existing
WARN_ON(), but used bitwise AND (&) instead of logical AND (&&), so the
condition is never true. Replace with logical AND.
Found by Coverity (CID 142811).
Fixes: 3448a19da4 "vgaarb: use bridges to control VGA routing where possible"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7c82126a94 upstream.
After a CPU upgrade while keeping the same mainboard, we faced "spurious
interrupt" problems again.
It turned out that the new CPU also featured a new GPU with a different PCI
ID.
Add this PCI ID to the quirk table. Probably all other Intel GPU PCI IDs
are affected, too, but I don't want to add them without a test system.
See f67fd55fa9 ("PCI: Add quirk for still enabled interrupts on Intel
Sandy Bridge GPUs") for some history.
[bhelgaas: add f67fd55fa9 reference, stable tag]
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb4f8f568a upstream.
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd9e83e275 upstream.
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d49cb7aeeb upstream.
commit 421e08c41f fixed the reported min/max for the X and Y axis,
but unfortunately, it broke the resolution of those same axis.
On the t540p, the resolution is the same regarding X and Y. It is not
a problem for xf86-input-synaptics because this driver is only interested
in the ratio between X and Y.
Unfortunately, xf86-input-cmt uses directly the resolution, and having a
null resolution leads to some divide by 0 errors, which are translated by
-infinity in the resulting coordinates.
Reported-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81a9c5e72b upstream.
On uniprocessor preemptible kernel, target core deadlocks on unload. The
following events happen:
* iscsit_del_np is called
* it calls send_sig(SIGINT, np->np_thread, 1);
* the scheduler switches to the np_thread
* the np_thread is woken up, it sees that kthread_should_stop() returns
false, so it doesn't terminate
* the np_thread clears signals with flush_signals(current); and goes back
to sleep in iscsit_accept_np
* the scheduler switches back to iscsit_del_np
* iscsit_del_np calls kthread_stop(np->np_thread);
* the np_thread is waiting in iscsit_accept_np and it doesn't respond to
kthread_stop
The deadlock could be resolved if the administrator sends SIGINT signal to
the np_thread with killall -INT iscsi_np
The reproducible deadlock was introduced in commit
db6077fd0b, but the thread-stopping code was
racy even before.
This patch fixes the problem. Using kthread_should_stop to stop the
np_thread is unreliable, so we test np_thread_state instead. If
np_thread_state equals ISCSI_NP_THREAD_SHUTDOWN, the thread exits.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 683497566d upstream.
This patch adds a explicit memset to the login response PDU
exception path in iscsit_tx_login_rsp().
This addresses a regression bug introduced in commit baa4d64b
where the initiator would end up not receiving the login
response and associated status class + detail, before closing
the login connection.
Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 97c99b47ac upstream.
This patch changes iscsit_check_dataout_hdr() to dump the incoming
Data-Out payload when the received ITT is not associated with a
WRITE, instead of calling iscsit_reject_cmd() for the non WRITE
ITT descriptor.
This addresses a bug where an initiator sending an Data-Out for
an ITT associated with a READ would end up generating a reject
for the READ, eventually resulting in list corruption.
Reported-by: Santosh Kulkarni <santosh.kulkarni@calsoftinc.com>
Reported-by: Arshad Hussain <arshad.hussain@calsoftinc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83ff42fcce upstream.
This patch fixes a left-over se_lun->lun_sep pointer OOPs when one
of the /sys/kernel/config/target/$FABRIC/$WWPN/$TPGT/lun/$LUN/alua*
attributes is accessed after the $DEVICE symlink has been removed.
To address this bug, go ahead and clear se_lun->lun_sep memory in
core_dev_unexport(), so that the existing checks for show/store
ALUA attributes in target_core_fabric_configfs.c work as expected.
Reported-by: Sebastian Herbszt <herbszt@gmx.de>
Tested-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e6015c1f8a upstream.
This change places MDMA1 in disabled node for Exynos5420.
If MDMA1 region is configured with secure mode, it makes
the boot failure with the following on smdk5420 board.
("Unhandled fault: imprecise external abort (0x1406) at 0x00000000")
Thus, arndale-octa board don't need to do the same thing anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783ee43118 upstream.
In generic_id the long int timestamp is multiplied by 100000 and needs
an explicit cast to u64.
Without that the id in the resulting pstore filename is wrong and
userspace may have problems parsing it, but more importantly files in
pstore can never be deleted and may fill the EFI flash (brick device?).
This happens because when generic pstore code wants to delete a file,
it passes the id to the EFI backend which reinterpretes it and a wrong
variable name is attempted to be deleted. There's no error message but
after remounting pstore, deleted files would reappear.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6b4a144a92 upstream.
In cross-build environment, we expect to use the cross-compiler objcopy
instead of the host objcopy.
It fixes following build failures:
objcopy --only-keep-debug lib/modules/3.14/kernel/net/ipv6/xfrm6_mode_tunnel.ko /srv/build/linux/debian/dbgtmp/usr/lib/debug/lib/modules/3.14/kernel/net/ipv6/xfrm6_mode_tunnel.ko
objcopy: Unable to recognise the format of the input file `lib/modules/3.14/kernel/net/ipv6/xfrm6_mode_tunnel.ko'
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
Fixes: 810e843746 ('deb-pkg: split debug symbols in their own package')
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ebe06187bf upstream.
This fixes use-after-free of epi->fllink.next inside list loop macro.
This loop actually releases elements in the body. The list is
rcu-protected but here we cannot hold rcu_read_lock because we need to
lock mutex inside.
The obvious solution is to use list_for_each_entry_safe(). RCU-ness
isn't essential because nobody can change this list under us, it's final
fput for this file.
The bug was introduced by ae10b2b4eb ("epoll: optimize EPOLL_CTL_DEL
using rcu")
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Jason Baron <jbaron@akamai.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 554086d85e upstream.
The bad syscall nr paths are their own incomprehensible route
through the entry control flow. Rearrange them to work just like
syscalls that return -ENOSYS.
This fixes an OOPS in the audit code when fast-path auditing is
enabled and sysenter gets a bad syscall nr (CVE-2014-4508).
This has probably been broken since Linux 2.6.27:
af0575bba0 i386 syscall audit fast-path
Cc: Roland McGrath <roland@redhat.com>
Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/e09c499eade6fc321266dd6b54da7beb28d6991c.1403558229.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4148c1f67a upstream.
There is one other possible overrun in the lz4 code as implemented by
Linux at this point in time (which differs from the upstream lz4
codebase, but will get synced at in a future kernel release.) As
pointed out by Don, we also need to check the overflow in the data
itself.
While we are at it, replace the odd error return value with just a
"simple" -1 value as the return value is never used for anything other
than a basic "did this work or not" check.
Reported-by: "Don A. Bailey" <donb@securitymouse.com>
Reported-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1895442be upstream.
We are currently allocating space_info objects in an array when we
allocate space_info. When a user does something like:
# btrfs balance start -mconvert=raid1 -dconvert=raid1 /mnt
# btrfs balance start -mconvert=single -dconvert=single /mnt -f
# btrfs balance start -mconvert=raid1 -dconvert=raid1 /
We can end up with memory corruption since the kobject hasn't
been reinitialized properly and the name pointer was left set.
The rationale behind allocating them statically was to avoid
creating a separate kobject container that just contained the
raid type. It used the index in the array to determine the index.
Ultimately, though, this wastes more memory than it saves in all
but the most complex scenarios and introduces kobject lifetime
questions.
This patch allocates the kobjects dynamically instead. Note that
we also remove the kobject_get/put of the parent kobject since
kobject_add and kobject_del do that internally.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed55b6ac07 upstream.
When encountering memory pressure, testers have run into the following
lockdep warning. It was caused by __link_block_group calling kobject_add
with the groups_sem held. kobject_add calls kvasprintf with GFP_KERNEL,
which gets us into reclaim context. The kobject doesn't actually need
to be added under the lock -- it just needs to ensure that it's only
added for the first block group to be linked.
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.14.0-rc8-default #1 Not tainted
---------------------------------------------------------
kswapd0/169 just changed the state of lock:
(&delayed_node->mutex){+.+.-.}, at: [<ffffffffa018baea>] __btrfs_release_delayed_node+0x3a/0x200 [btrfs]
but this lock took another, RECLAIM_FS-unsafe lock in the past:
(&found->groups_sem){+++++.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&found->groups_sem);
local_irq_disable();
lock(&delayed_node->mutex);
lock(&found->groups_sem);
<Interrupt>
lock(&delayed_node->mutex);
*** DEADLOCK ***
2 locks held by kswapd0/169:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff81159e8a>] shrink_slab+0x3a/0x160
#1: (&type->s_umount_key#27){++++..}, at: [<ffffffff811bac6f>] grab_super_passive+0x3f/0x90
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3e2426bd0e upstream.
If this condition in end_extent_writepage() is false:
if (tree->ops && tree->ops->writepage_end_io_hook)
we will then test an uninitialized "ret" at:
ret = ret < 0 ? ret : -EIO;
The test for ret is for the case where ->writepage_end_io_hook
failed, and we'd choose that ret as the error; but if
there is no ->writepage_end_io_hook, nothing sets ret.
Initializing ret to 0 should be sufficient; if
writepage_end_io_hook wasn't set, (!uptodate) means
non-zero err was passed in, so we choose -EIO in that case.
Signed-of-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Bolle
Anton Blanchard
Benjamin Herrenschmidt
Michael Ellerman
Gavin Shan
Scott Mayhew
Mateusz Guzik
Trond Myklebust
Christoph Hellwig
J. Bruce Fields
Bart Van Assche
Dennis Dalessandro
Mike Marciniszyn
Yann Droneaud
Don Zickus
gundberg
Gabor Juhos
Viresh Kumar
hujianyang
Markos Chandras
Alex Smith
Asai Thambi S P
Bjorn Helgaas
Thomas Jarosch
Hans de Goede
Benjamin Tissoires
Mikulas Patocka
Nicholas Bellinger
Seungwon Jeon
Greg Kroah-Hartman
Andrzej Zaborowski
Fathi Boudra
Konstantin Khlebnikov
Andy Lutomirski
Jeff Mahoney
Eric Sandeen