Commit Graph

2240 Commits

Author SHA1 Message Date
Yinghai dda5654927 intel-iommu: use physfn to search drhd for VF
When virtfn is used, we should use physfn to find correct drhd

-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
     do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
     also change dmar_pci_device_match() static

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 17:00:00 +01:00
Yinghai Lu 680a752462 intel-iommu: Print out iommu seq_id
more info on system with more than one IOMMU

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 16:33:13 +01:00
Yinghai Lu 5715f0f9d3 intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 16:32:18 +01:00
Nadav Amit 78d5f0f500 intel-iommu: Avoid global flushes with caching mode.
While it may be efficient on real hardware, emulation of global
invalidations is very expensive as all shadow entries must be examined.
This patch changes the behaviour when caching mode is enabled (which is
the case when IOMMU emulation takes place). In this case, page specific
invalidation is used instead.

Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 15:54:41 +01:00
Nadav Amit 82653633b6 intel-iommu: Use correct domain ID when caching mode is enabled
In caching-mode mappings of pages (changes from non-present to present)
require invalidation.
Currently, this IOTLB flush is performed with domain ID of zero.
This is not according to the VT-d spec and causes big problems for
emulating software.
This patch uses the correct domain ID in IOTLB flushes.
Device IOTLB invalidation is performed only on present to non-present
changes. This decision is now based on explicit parameter instead of
zero domain-ID.

Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 15:39:21 +01:00
Nadav Amit 8bdd77dd4e intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel_map_sg used offset_pfn which was set to zero when invalidating the IOTLB.
intel_map_sg now uses size variable for this matter.

Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 15:38:47 +01:00
Akinobu Mita a45946abb8 intel-iommu: use for_each_set_bit()
Replace open-coded loop with for_each_set_bit().

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-04-09 15:24:11 +01:00
David Woodhouse 87d8a69709 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 2010-04-09 15:21:12 +01:00
Alexander Duyck 4352aa5bbf PCI aerdrv: use correct bit defines and add 2ms delay to aer_root_reset
While testing completion timeouts I found that hardware was not recovering.
It looks like the hot reset was never being propagated to the endpoint
devices on the bus due to the fact that we were clearing the bit too
quickly.

The documentation I have states that we should be transmitting hot reset
TS1s for 2ms.  To achieve this I have added a 2ms delay from the time we
set the secondary bus reset bit to the time we clear it.  In addition I
changed the define used for the secondary bus reset bit to match the
register define that was being used.

Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-04-08 09:24:11 -07:00
Tejun Heo 336f5899d2 Merge branch 'master' into export-slabh 2010-04-05 11:37:28 +09:00
Clemens Ladisch 5193d7a7f5 PCI quirk: RS780/RS880: disable MSI behind the PCI bridge
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines.  To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.

[rjw: Added the PCI_VENDOR_ID_AI quirk.]

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-04-02 19:47:05 -07:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Linus Torvalds b72c40949b Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/PCI: truncate _CRS windows with _LEN > _MAX - _MIN + 1
  x86/PCI: for host bridge address space collisions, show conflicting resource
  frv/PCI: remove redundant warnings
  x86/PCI: remove redundant warnings
  PCI: don't say we claimed a resource if we failed
  PCI quirk: Disable MSI on VIA K8T890 systems
  PCI quirk: RS780/RS880: work around missing MSI initialization
  PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
  PCI: complain about devices that seem to be broken
  PCI: print resources consistently with %pR
  PCI: make disabled window printk style match the enabled ones
  PCI: break out primary/secondary/subordinate for readability
  PCI: for address space collisions, show conflicting resource
  resources: add interfaces that return conflict information
  PCI: cleanup error return for pcix get and set mmrbc functions
  PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
  PCI: kill off pci_register_set_vga_state() symbol export.
  PCI: fix return value from pcix_get_max_mmrbc()
2010-03-26 16:34:29 -07:00
Bjorn Helgaas f967a44343 PCI: don't say we claimed a resource if we failed
pci_claim_resource() can fail, so pay attention and only claim success
when it actually succeeded.  If pci_claim_resource() fails, it prints a
useful diagnostic.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-25 08:51:35 -07:00
Matthew Wilcox 134b345081 PCI quirk: Disable MSI on VIA K8T890 systems
Bugzilla 15287 indicates that there's a problem with Message Signalled
Interrupts on VIA K8T890 systems.  Add a quirk to disable MSI on these
systems.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Tested-by: lh <jarryson@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-25 08:51:23 -07:00
Clemens Ladisch a5ee4eb754 PCI quirk: RS780/RS880: work around missing MSI initialization
AMD says in section 2.5.4 (GFX MSI Enable) of #43291 (AMD 780G Family
Register Programming Requirements):

  The SBIOS must enable internal graphics MSI capability in GCCFG by
  setting the following: NBCFG.NB_CNTL.STRAP_MSI_ENABLE='1'

Quite a few BIOS writers misinterpret this sentence and think that
enabling MSI is an optional feature.  However, clearing that bit just
prevents delivery of MSI messages but does not remove the MSI PCI
capabilities registers, and so leaves these devices unusable for any
driver that attempts to use MSI.

Setting that bit is not possible after the BIOS has locked down the
configuration registers, so we have to manually disable MSI for the
affected devices.

This fixes the codec communication errors in the HDA driver when
accessing the HDMI audio device, and allows us to get rid of the
overcautious quirk in radeon_irq_kms.c.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Alex Deucher <alexdeucher@gamil.com>
Cc: <stable@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:38 -07:00
Tim Yamin ca84639263 PCI quirk: only apply CX700 PCI bus parking quirk if external VT6212L is present
Apply the CX700 quirk only when an external VT6212L is present (which
is the case for the errant hardware the quirk was written for), don't
touch the settings otherwise -- Hauppage PVR-500 tuners need PCI Bus
Parking in order to work and when that's turned on everything seems
to behave fine.

I guess the underlying problem is a combination of an external VT6212L
and the CX700 rather than the CX700's PCI being broken completely for
all cases...

Reported-by: Jeroen Roos <jeroen@roosnl.com>
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:37 -07:00
Bjorn Helgaas c519a5a7da PCI: complain about devices that seem to be broken
If we can tell that a device isn't working correctly, we should tell
the user to make debugging easier.  Otherwise, it can take a lot of
work to determine whether the problem is in the driver, PCMCIA, PCI,
hardware, etc., as in http://bugzilla.kernel.org/show_bug.cgi?id=12006

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:36 -07:00
Bjorn Helgaas e1944c6b0f PCI: print resources consistently with %pR
No functional change; just print resources in the conventional style.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:36 -07:00
Bjorn Helgaas 7b8ff6da02 PCI: make disabled window printk style match the enabled ones
No functional change; this just tweaks the changes from 349e1823a405
so the new printks for disabled PCI-to-PCI bridge windows match the
ones for the enabled windows.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:35 -07:00
Bjorn Helgaas 99ddd552fe PCI: break out primary/secondary/subordinate for readability
No functional change; just add names for the primary/secondary/subordinate
bus numbers read from config space rather than repeatedly masking/shifting.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:35 -07:00
Bjorn Helgaas 966f3a7570 PCI: for address space collisions, show conflicting resource
With request_resource_conflict(), we can learn what the actual conflict is,
so print that info for debugging purposes.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-24 13:21:34 -07:00
Linus Torvalds 2eb645e7b5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  driver core: numa: fix BUILD_BUG_ON for node_read_distance
  driver-core: document ERR_PTR() return values
  kobject: documentation: Update to refer to kset-example.c.
  sysdev: the cpu probe/release attributes should be sysdev_class_attributes
  kobject: documentation: Fix erroneous example in kobject doc.
  driver-core: fix missing kernel-doc in firmware_class
  Driver core: Early platform kernel-doc update
  sysfs: fix sysfs lockdep warning in mlx4 code
  sysfs: fix sysfs lockdep warning in infiniband code
  sysfs: fix sysfs lockdep warning in ipmi code
  sysfs: Initialised pci bus legacy_mem field before use
  sysfs: use sysfs_bin_attr_init in firmware class driver
2010-03-19 13:39:42 -07:00
Dean Nelson 7c9e2b1c47 PCI: cleanup error return for pcix get and set mmrbc functions
pcix_get_mmrbc() returns the maximum memory read byte count (mmrbc), if
successful, or an appropriate error value, if not.

Distinguishing errors from correct values and understanding the meaning of an
error can be somewhat confusing in that:

	correct values: 512, 1024, 2048, 4096
	errors: -EINVAL  			-22
 		PCIBIOS_FUNC_NOT_SUPPORTED	0x81
		PCIBIOS_BAD_VENDOR_ID		0x83
		PCIBIOS_DEVICE_NOT_FOUND	0x86
		PCIBIOS_BAD_REGISTER_NUMBER	0x87
		PCIBIOS_SET_FAILED		0x88
		PCIBIOS_BUFFER_TOO_SMALL	0x89

The PCIBIOS_ errors are returned from the PCI functions generated by the
PCI_OP_READ() and PCI_OP_WRITE() macros.

In a similar manner, pcix_set_mmrbc() also returns the PCIBIOS_ error values
returned from pci_read_config_[word|dword]() and pci_write_config_word().

Following pcix_get_max_mmrbc()'s example, the following patch simply returns
-EINVAL for all PCIBIOS_ errors encountered by pcix_get_mmrbc(), and -EINVAL
or -EIO for those encountered by pcix_set_mmrbc().

This simplification was chosen in light of the fact that none of the current
callers of these functions are interested in the specific type of error
encountered. In the future, should this change, one could simply create a
function that maps each PCIBIOS_ error to a corresponding unique errno value,
which could be called by pcix_get_max_mmrbc(), pcix_get_mmrbc(), and
pcix_set_mmrbc().

Additionally, this patch eliminates some unnecessary variables.

Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-19 12:41:48 -07:00
Dean Nelson bdc2bda7c4 PCI: fix access of PCI_X_CMD by pcix get and set mmrbc functions
An e1000 driver on a system with a PCI-X bus was always being returned
a value of 135 from both pcix_get_mmrbc() and pcix_set_mmrbc(). This
value reflects an error return of PCIBIOS_BAD_REGISTER_NUMBER from
pci_bus_read_config_dword(,, cap + PCI_X_CMD,).

This is because for a dword, the following portion of the PCI_OP_READ()
macro:

	if (PCI_##size##_BAD) return PCIBIOS_BAD_REGISTER_NUMBER;

expands to:

	if (pos & 3) return PCIBIOS_BAD_REGISTER_NUMBER;

And is always true for 'cap + PCI_X_CMD', which is 0xe4 + 2 = 0xe6. ('cap' is
the result of calling pci_find_capability(, PCI_CAP_ID_PCIX).)

The same problem exists for pci_bus_write_config_dword(,, cap + PCI_X_CMD,).
In both cases, instead of calling _dword(), _word() should be called.

Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-19 12:40:22 -07:00
Paul Mundt ded1d8f29b PCI: kill off pci_register_set_vga_state() symbol export.
When pci_register_set_vga_state() was made __init, the EXPORT_SYMBOL() was
retained, which now leaves us with a section mismatch.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Mike Travis <travis@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-19 12:38:18 -07:00
Dean Nelson 25daeb550b PCI: fix return value from pcix_get_max_mmrbc()
For the PCI_X_STATUS register, pcix_get_max_mmrbc() is returning an incorrect
value, which is based on:

	(stat & PCI_X_STATUS_MAX_READ) >> 12

Valid return values are 512, 1024, 2048, 4096, which correspond to a 'stat'
(masked and right shifted by 21) of 0, 1, 2, 3, respectively.

A right shift by 11 would generate the correct return value when 'stat' (masked
and right shifted by 21) has a value of 1 or 2. But for a value of 0 or 3 it's
not possible to generate the correct return value by only right shifting.

Fix is based on pcix_get_mmrbc()'s similar dealings with the PCI_X_CMD register.

Cc: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-19 12:36:51 -07:00
Mel Gorman 6757eca348 sysfs: Initialised pci bus legacy_mem field before use
PPC64 is failing to boot the latest mmotm due to an uninitialised pointer in
pci_create_legacy_files(). The surprise is that machines boot at all and it
would appear to affect current mainline as well.  This patch fixes the problem.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19 07:12:11 -07:00
Linus Torvalds 722874465e Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (27 commits)
  microblaze: entry.S use delay slot for return handlers
  microblaze: Save current task directly
  microblaze: Simplify entry.S - save/restore r3/r4 - ret_from_trap
  microblaze: PCI early support for noMMU system
  microblaze: Fix dma alloc and free coherent dma functions
  microblaze: Add consistent code
  microblaze: pgtable.h: move consistent functions
  microblaze: Remove ancient Kconfig option for consistent mapping
  microblaze: Remove VMALLOC_VMADDR
  microblaze: Add define for ASM_LOOP
  microblaze: Preliminary support for dma drivers
  microblaze: remove trailing space in messages
  microblaze: Use generic show_mem()
  microblaze: Change temp register for cmdline
  microblaze: Preliminary support for dma drivers
  microblaze: Move cache function to cache.c
  microblaze: Add support from PREEMPT
  microblaze: Add support for Xilinx PCI host bridge
  microblaze: Enable PCI, missing files
  microblaze: Add core PCI files
  ...
2010-03-18 16:57:24 -07:00
Thomas Weber 8839316121 Fix typos in comments
[Ss]ytem => [Ss]ystem
udpate => update
paramters => parameters
orginal => original

Signed-off-by: Thomas Weber <swirl@gmx.li>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-03-16 11:47:56 +01:00
Len Brown ec28dcc6b4 Merge branches 'battery-2.6.34', 'bugzilla-10805', 'bugzilla-14668', 'bugzilla-531916-power-state', 'ht-warn-2.6.34', 'pnp', 'processor-rename', 'sony-2.6.34', 'suse-bugzilla-531547', 'tz-check', 'video' and 'misc-2.6.34' into release 2010-03-14 21:30:17 -04:00
Shaohua Li d060705091 acpiphp: Execute ACPI _REG method for hotadded devices
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.

Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
2010-03-14 16:40:50 -04:00
FUJITA Tomonori 5f3cd1e0bb dma-mapping: pci: move pci_set_dma_mask and pci_set_consistent_dma_mask to pci-dma-compat.h
We can use pci-dma-compat.h to implement pci_set_dma_mask and
pci_set_consistent_dma_mask as we do with the other PCI DMA API.

We can remove HAVE_ARCH_PCI_SET_DMA_MASK too.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:42 -08:00
FUJITA Tomonori 6a1961f49e dma-mapping: dma-mapping.h: add dma_set_coherent_mask
dma_set_coherent_mask corresponds to pci_set_consistent_dma_mask.  This is
necessary to move to the generic device model DMA API from the PCI bus
specific API in the long term.

dma_set_coherent_mask works in the exact same way that
pci_set_consistent_dma_mask does.  So this patch also changes
pci_set_consistent_dma_mask to call dma_set_coherent_mask.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:42 -08:00
FUJITA Tomonori e3c4bccaba dma-mapping: pci: convert pci_set_dma_mask to call dma_set_mask
This changes pci_set_dma_mask to call the generic DMA API, dma_set_mask.

pci_set_dma_mask (in drivers/pci/pci.c) does the same things that
dma_set_mask does on all the architectures that use pci_set_dma_mask;
calls dma_supprted and sets dev->dma_mask.  So we safely change
pci_set_dma_mask to simply call dma_set_mask.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:42 -08:00
Michal Simek a6475c1322 microblaze: Enable PCI, missing files
There are two parts of changes. The first is just enable
PCI in Makefiles and in Kconfig. The second is the rest of
missing files. I didn't want to add it with previous patch
because that patch is too big.

Current Microblaze toolchain has problem with weak symbols
that's why is necessary to apply this changes to be possible
to compile pci support.
Xilinx knows about this problem.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-03-11 14:04:27 +01:00
Linus Torvalds 522dba7134 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI/PM Runtime: Make runtime PM of PCI devices inactive by default
2010-03-08 16:10:29 -08:00
Greg Kroah-Hartman 8e9394ce24 Driver core: create lock/unlock functions for struct device
In the future, we are going to be changing the lock type for struct
device (once we get the lockdep infrastructure properly worked out)  To
make that changeover easier, and to possibly burry the lock in a
different part of struct device, let's create some functions to lock and
unlock a device so that no out-of-core code needs to be changed in the
future.

This patch creates the device_lock/unlock/trylock() functions, and
converts all in-tree users to them.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <len.brown@intel.com>
Cc: Magnus Damm <damm@igel.co.jp>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Alex Chiang <achiang@hp.com>
Cc: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Yu Zhao <yu.zhao@intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wolfram Sang <w.sang@pengutronix.de>
Cc: CHENG Renquan <rqcheng@smu.edu.sg>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:52 -08:00
Stephen Rothwell 62e877b893 sysfs: fix for thinko with sysfs_bin_attr_init()
After merging the final tree, today's linux-next build (powerpc
allyesconfig) failed like this:

drivers/pci/pci-sysfs.c: In function 'pci_create_legacy_files':
drivers/pci/pci-sysfs.c:645: error: lvalue required as unary '&' operand
drivers/pci/pci-sysfs.c:658: error: lvalue required as unary '&' operand

Caused by commit "sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on
dynamic attributes" interacting with commit "sysfs: Use one lockdep
class per sysfs attribute") both from the driver-core tree.

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:52 -08:00
Eric W. Biederman a07e4156a2 sysfs: Use sysfs_attr_init and sysfs_bin_attr_init on dynamic attributes
These are the non-static sysfs attributes that exist on
my test machine.  Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate.   It simply requires
making a sysfs attribute present to see this.  So this
is a little bit tedious but otherwise not too bad.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:51 -08:00
Emese Revfy 52cf25d0ab Driver core: Constify struct sysfs_ops in struct kobj_type
Constify struct sysfs_ops.

This is part of the ops structure constification
effort started by Arjan van de Ven et al.

Benefits of this constification:

 * prevents modification of data that is shared
   (referenced) by many other structure instances
   at runtime

 * detects/prevents accidental (but not intentional)
   modification attempts on archs that enforce
   read-only kernel data at runtime

 * potentially better optimized code as the compiler
   can assume that the const data cannot be changed

 * the compiler/linker move const data into .rodata
   and therefore exclude them from false sharing

Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: David Teigland <teigland@redhat.com>
Acked-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-07 17:04:49 -08:00
Linus Torvalds 322aafa664 Merge branch 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-mrst-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  x86, mrst: Fix whitespace breakage in apb_timer.c
  x86, mrst: Fix APB timer per cpu clockevent
  x86, mrst: Remove X86_MRST dependency on PCI_IOAPIC
  x86, olpc: Use pci subarch init for OLPC
  x86, pci: Add arch_init to x86_init abstraction
  x86, mrst: Add Kconfig dependencies for Moorestown
  x86, pci: Exclude Moorestown PCI code if CONFIG_X86_MRST=n
  x86, numaq: Make CONFIG_X86_NUMAQ depend on CONFIG_PCI
  x86, pci: Add sanity check for PCI fixed bar probing
  x86, legacy_irq: Remove duplicate vector assigment
  x86, legacy_irq: Remove left over nr_legacy_irqs
  x86, mrst: Platform clock setup code
  x86, apbt: Moorestown APB system timer driver
  x86, mrst: Add vrtc platform data setup code
  x86, mrst: Add platform timer info parsing code
  x86, mrst: Fill in PCI functions in x86_init layer
  x86, mrst: Add dummy legacy pic to platform setup
  x86/PCI: Moorestown PCI support
  x86, ioapic: Add dummy ioapic functions
  x86, ioapic: Early enable ioapic for timer irq
  ...

Fixed up semantic conflict of new clocksources due to commit
17622339af ("clocksource: add argument to resume callback").
2010-03-07 15:59:39 -08:00
Joerg Roedel b146a1c9f7 VT-d: Change {un}map_range functions to implement {un}map interface
This patch changes the iommu-api functions for mapping and
unmapping page ranges to use the new page-size based
interface. This allows to remove the range based functions
later.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2010-03-07 18:01:11 +01:00
Joerg Roedel 4abc14a733 iommu-api: Rename ->{un}map function pointers to ->{un}map_range
The new function pointer names match better with the
top-level functions of the iommu-api which are using them.
Main intention of this change is to make the ->{un}map
pointer names free for two new mapping functions.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
2010-03-07 18:01:11 +01:00
Maxim Levitsky 03cd8f7ebe ricoh_mmc: port from driver to pci quirk
This patch solves nasty problem original driver has.

Original goal of the ricoh_mmc was to disable this device because then,
mmc cards can be read using standard SDHCI controller, thus avoiding
writing of yet another driver.

However, the act of disablement, makes other pci functions that belong to
this controller (xD and memstick) shift up one level, thus pci core has
now wrong idea about these devices.

To fix this issue, this patch moves the driver into the pci quirk section,
thus it is executes before the pci is enumerated, and therefore solving
that issue, also same sequence of commands is performed on resume for same
reasons.

Also regardless of the above, this way is cleaner.  You still need to set
CONFIG_MMC_RICOH_MMC to enable this quirk

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Philip Langdale <philipl@overt.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-06 11:26:36 -08:00
Rafael J. Wysocki bb910a7040 PCI/PM Runtime: Make runtime PM of PCI devices inactive by default
Make the run-time power management of PCI devices be inactive by
default by calling pm_runtime_forbid() for each PCI device during its
initialization.  This setting may be overriden by the user space with
the help of the /sys/devices/.../power/control interface.

That's necessary to avoid breakage on systems where ACPI-based
wake-up is known to fail for some devices.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-03-05 15:09:39 -08:00
Linus Torvalds a626b46e17 Merge branch 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
  early_res: Need to save the allocation name in drop_range_partial()
  sparsemem: Fix compilation on PowerPC
  early_res: Add free_early_partial()
  x86: Fix non-bootmem compilation on PowerPC
  core: Move early_res from arch/x86 to kernel/
  x86: Add find_fw_memmap_area
  Move round_up/down to kernel.h
  x86: Make 32bit support NO_BOOTMEM
  early_res: Enhance check_and_double_early_res
  x86: Move back find_e820_area to e820.c
  x86: Add find_early_area_size
  x86: Separate early_res related code from e820.c
  x86: Move bios page reserve early to head32/64.c
  sparsemem: Put mem map for one node together.
  sparsemem: Put usemap for one node together
  x86: Make 64 bit use early_res instead of bootmem before slab
  x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
  x86: Make early_node_mem get mem > 4 GB if possible
  x86: Dynamically increase early_res array size
  x86: Introduce max_early_res and early_res_count
  ...
2010-03-03 08:15:05 -08:00
Linus Torvalds 6d6b89bd2e Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
  virtio_net: remove forgotten assignment
  be2net: fix tx completion polling
  sis190: fix cable detect via link status poll
  net: fix protocol sk_buff field
  bridge: Fix build error when IGMP_SNOOPING is not enabled
  bnx2x: Tx barriers and locks
  scm: Only support SCM_RIGHTS on unix domain sockets.
  vhost-net: restart tx poll on sk_sndbuf full
  vhost: fix get_user_pages_fast error handling
  vhost: initialize log eventfd context pointer
  vhost: logging thinko fix
  wireless: convert to use netdev_for_each_mc_addr
  ethtool: do not set some flags, if others failed
  ipoib: returned back addrlen check for mc addresses
  netlink: Adding inode field to /proc/net/netlink
  axnet_cs: add new id
  bridge: Make IGMP snooping depend upon BRIDGE.
  bridge: Add multicast count/interval sysfs entries
  bridge: Add hash elasticity/max sysfs entries
  bridge: Add multicast_snooping sysfs toggle
  ...

Trivial conflicts in Documentation/feature-removal-schedule.txt
2010-03-02 07:55:08 -08:00
Linus Torvalds bc53515413 Merge branch 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: replace acpi_integer by u64
  ACPICA: Update version to 20100121.
  ACPICA: Remove unused uint32_struct type
  ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
  ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
  ACPICA: Predefined name repair: fix NULL package elements
  ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
  ACPICA: Update all ACPICA copyrights and signons to 2010
  ACPICA: Update for new gcc-4 warning options
2010-03-01 10:36:22 -08:00
Yinghai Lu 9a928660c9 pci: don't reassign to ROM res if it is not going to be enabled
A ROM resource that doesn't fit should not cause us to try to re-assign
all the bus resources.  Nobody generally cares, and re-assigning is
going to just cause way more troubles than it tries to solve.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-01 07:41:55 -08:00
David S. Miller 47871889c6 Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Conflicts:
	drivers/firmware/iscsi_ibft.c
2010-02-28 19:23:06 -08:00
Linus Torvalds c7e15899d0 Merge branch 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Enable NMI on all cpus on UV
  vgaarb: Add user selectability of the number of GPUS in a system
  vgaarb: Fix VGA arbiter to accept PCI domains other than 0
  x86, uv: Update UV arch to target Legacy VGA I/O correctly.
  pci: Update pci_set_vga_state() to call arch functions
2010-02-28 10:59:18 -08:00
Matt Carlson 4067a8541d pci: Add helper to search for VPD keywords
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:33 -08:00
Matt Carlson b55ac1b226 pci: Add helper to find a VPD resource data type
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:32 -08:00
Rafael J. Wysocki a1e4d72cd3 PM: Allow PCI devices to suspend/resume asynchronously
Set power.async_suspend for all PCI devices and PCIe port services,
so that they can be suspended and resumed in parallel with other
devices they don't depend on in a known way (i.e. devices which are
not their parents or children).

This only affects the "regular" suspend and resume stages, which
means in particular that the restoration of the PCI devices' standard
configuration registers during resume will still be carried out
synchronously (at the "early" resume stage).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-02-26 20:39:12 +01:00
Bjorn Helgaas 2fe2abf896 PCI: augment bus resource table with a list
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge.  We've increased this size
several times when the table overflowed.

But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.

This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode.  Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.

I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture.  This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:37 -08:00
Bjorn Helgaas 89a74ecccd PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
No functional change; this converts loops that iterate from 0 to
PCI_BUS_NUM_RESOURCES through pci_bus resource[] table to use the
pci_bus_for_each_resource() iterator instead.

This doesn't change the way resources are stored; it merely removes
dependencies on the fact that they're in a table.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:31 -08:00
Bjorn Helgaas 2adf75160b PCI: read bridge windows before filling in subtractive decode resources
No functional change; this fills in the bus subtractive decode resources
after reading the bridge window information rather than before.  Also,
print out the subtractive decode resources as we already do for the
positive decode windows.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:25 -08:00
Bjorn Helgaas fa27b2d108 PCI: split up pci_read_bridge_bases()
No functional change; this breaks up pci_read_bridge_bases() into separate
pieces for the I/O, memory, and prefetchable memory windows, similar to how
Yinghai recently split up pci_setup_bridge() in 68e84ff3bdc.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-23 09:43:17 -08:00
Kenji Kaneshige b16694f70c PCIe PME: use pci_pcie_cap()
Use pci_pcie_cap() instead of pci_find_capability() to get PCIe
capability offset. This reduces redundant search in PCI configuration
space.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:21:21 -08:00
Rafael J. Wysocki 6cbf82148f PCI PM: Run-time callbacks for PCI bus type
Introduce run-time PM callbacks for the PCI bus type.  Make the new
callbacks work in analogy with the existing system sleep PM
callbacks, so that the drivers already converted to struct dev_pm_ops
can use their suspend and resume routines for run-time PM without
modifications.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:21:19 -08:00
Kenji Kaneshige 552be54cc4 PCIe PME: use pci_is_pcie()
Use pci_is_pcie() instead of looking at obsolete is_pcie field in
struct pci_dev.

Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:21:10 -08:00
Rafael J. Wysocki b67ea76172 PCI / ACPI / PM: Platform support for PCI PME wake-up
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel.  If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.

Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited.  The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.

Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
  handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
  pci_platform_pm_ops allowing us to enable/disable the platform to
  generate wake-up events for given device.  Implemet this callback
  for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
  make the PCI-ACPI binding code register wake-up notifiers for all
  PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
  check if given device is capable of generating wake-up events at
  run time.

Developed in cooperation with Matthew Garrett <mjg@redhat.com>.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:21:02 -08:00
Rafael J. Wysocki c39fae1416 PCI PM: Make it possible to force using INTx for PCIe PME signaling
Apparently, some machines may have problems with PCI run-time power
management if MSIs are used for the native PCIe PME signaling.  In
particular, on the MSI Wind U-100 PCIe PME interrupts are not
generated by a PCIe root port after a resume from suspend to RAM, if
the system wake-up was triggered by a PME from the device attached to
this port.  [It doesn't help to free the interrupt on suspend and
request it back on resume, even if that is done along with disabling
the MSI and re-enabling it, respectively.]  However, if INTx
interrupts are used for this purpose on the same machine, everything
works just fine.

For this reason, add a kernel command line switch allowing one to
request that MSIs be not used for the native PCIe PME signaling,
introduce a DMI table allowing us to blacklist machines that need
this switch to be set by default and put the MSI Wind U-100 into this
table.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:20:39 -08:00
Rafael J. Wysocki c7f486567c PCI PM: PCIe PME root port service driver
PCIe native PME detection mechanism is based on interrupts generated
by root ports or event collectors every time a PCIe device sends a
PME message upstream.

Once a PME message has been sent by an endpoint device and received
by its root port (or event collector in the case of root complex
integrated endpoints), the Requester ID from the message header is
registered in the root port's Root Status register.  At the same
time, the PME Status bit of the Root Status register is set to
indicate that there's a PME to handle.  If PCIe PME interrupt is
enabled for the root port, it generates an interrupt once the PME
Status has been set.  After receiving the interrupt, the kernel can
identify the PCIe device that generated the PME using the Requester
ID from the root port's Root Status register. [For details, see PCI
Express Base Specification, Rev. 2.0.]

Implement a driver for the PCIe PME root port service working in
accordance with the above description.

Based on a patch from Shaohua Li <shaohua.li@intel.com>.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:20:31 -08:00
Rafael J. Wysocki 58ff463396 PCI PM: Add function for checking PME status of devices
Add function pci_check_pme_status() that will check the PME status
bit of given device and clear it along with the PME enable bit.  It
will be necessary for PCI run-time power management.

Based on a patch from Shaohua Li <shaohua.li@intel.com>

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:20:24 -08:00
Yinghai Lu 9958610552 PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
Make pci_bridge_check_ranges() store the PCI_PREF_RANGE_TYPE_64 in
addition to IORESOURCE_MEM_64.  Just like pci_read_bridge_bases().

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:25 -08:00
Yinghai Lu 32180e402f PCI: pciehp: second try to get big range for pcie devices
Handle the case where the slot bridge that doesn't get a pre-allocated
resource big enough to handle its child resources..  For example pcie
devices need 256M, but the bridge only gets 2M preallocated.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:25 -08:00
Yinghai Lu 9789ac979b PCI: pciehp: cleanup flow in pciehp_configure_device
Move bus_size_bridges and assign resources out of pciehp_add_bridge()
and do them all together, one time, including slot bridge, to avoid to
calling assign resources several times when there are several bridges
under the slot bridge.  Using pci_assign_unassigned_bridge_resources.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:24 -08:00
Yinghai Lu 6841ec681a PCI: introduce pci_assign_unassigned_bridge_resources
For use by pciehp.

pci_setup_bridge() will not check enabled for the slot bridge, otherwise
update res is not updated to bridge BAR.  That is, bridge is already
enabled for port service.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:23 -08:00
Yinghai Lu 977d17bb17 PCI: update bridge resources to get more big ranges in PCI assign unssigned
BIOS separates IO ranges between several IOHs, and on some slots, BIOS assigns
resources to a bridge, but stops assigning resources to the device under that
bridge, because the device needs a big resource.

So:
  1. allocate resources and record the failed device resources
  2. clear the BIOS assigned resources of the parent bridge of failing device
  3. go back and call pci assign unassigned
  4. if it still fails, go up the tree, clear more bridges. and try again

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:22 -08:00
Yinghai Lu d65245c329 PCI: don't shrink bridge resources
When clearing leaf bridge resources, trying to get a big enough one, we
could shrink the bridge if there is no resource under it.  Confirm
against the old resource side to make sure we're increasing the
allocation.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:21 -08:00
Yinghai Lu cd81e1ea1a PCI: reject mmio ranges starting at 0 on pci_bridge read
We already track unassigned resources in struct resource, and this
prevents us from overwriting resource flags and info in the unassigned
case.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:21 -08:00
Yinghai Lu 568ddef873 PCI: add failed_list to pci_bus_assign_resources
This allows us to track failed allocations for later re-trying with
reallocation.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:20 -08:00
Yinghai Lu 5009b46025 PCI: add pci_bridge_release_resources and pci_bus_release_bridge_resources
We use this in later patches to free resrouce ranges for reassignment in
an effort to support a wider variety of PCI topologies.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:19 -08:00
Andrew Morton ba02b242bb PCI hotplug: check ioremap() return value in ibmphp_ebda.c
check ioremap() return value.

Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:19 -08:00
Randy Dunlap 939fdc6735 PCI hotplug: fix ibmphp build error
Add header file to fix build error:

drivers/pci/hotplug/ibmphp_hpc.c:135: error: implicit declaration of function 'init_MUTEX'
drivers/pci/hotplug/ibmphp_hpc.c:136: error: implicit declaration of function 'init_MUTEX_LOCKED'
drivers/pci/hotplug/ibmphp_hpc.c:797: error: implicit declaration of function 'down'
drivers/pci/hotplug/ibmphp_hpc.c:807: error: implicit declaration of function 'up'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:18 -08:00
Matthew Wilcox 4fb88c1a28 PCI: Make pci_scan_slot more robust
Yinghai pointed out that the new pci_scan_slot() crashes when called
on an ARI-capable slot that is empty.  Fix this by exiting early from
pci_scan_slot if there is no device in the slot.

Also make next_ari_func() robust against devices not existing in case
the ARI capability is corrupt.  ARI also requires that the devices be
listed in order, so if we find a function listed that is out of order,
stop scanning to prevent loops.

Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:17 -08:00
Jiri Slaby 0bf01c3c86 PCI: hotplug/cpcihp, fix pci device refcounting
Stanse found an ommitted pci_dev_put on one error path in
cpcihp_generic_init. The path is taken on !dev, but also when
dev->hdr_type != PCI_HEADER_TYPE_BRIDGE. However it omits to
pci_dev_put on the latter.

As it is fine to pass NULL to pci_dev_put, put it in there
uncoditionally.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Scott Murray <scott@spiteful.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:02 -08:00
Tilman Schmidt 41a68a748b PCI: push deprecated pci_find_device() function to last user
The ISDN4Linux HiSax driver family contains the last remaining users
of the deprecated pci_find_device() function. This patch creates a
private copy of that function in HiSax, and removes the now unused
global function together with its controlling configuration option,
CONFIG_PCI_LEGACY.

Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:01 -08:00
Yinghai Lu 7c9342b8dd PCI: don't dump resource when bus resource flags indicates unused
Don't print out resources without flags to avoid cluttering up the debug
output.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:17:00 -08:00
Yinghai Lu 7cc5997d1d PCI: separate pci_setup_bridge to small functions
This is a good cleanup in itself, and makes it easier to modify specific
resource types in later code.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:16:59 -08:00
Chandru b0fc889c43 PCI hotplug: ibmphp: read the length of ebda and map entire ebda region
ibmphp driver currently maps only 1KB of ebda memory area into kernel address
space during driver initialization. This causes kernel oops when the driver is
modprobe'd and it accesses memory beyond 1KB within ebda segment. The first
byte of ebda segment actually stores the length of the ebda region in
Kilobytes. Hence make use of the length parameter and map the entire ebda
region.

Signed-off-by: Chandru Siddalingappa <chandru@linux.vnet.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:16:58 -08:00
Jiri Slaby 6fcaf17ac7 PCI hotplug: fix memory leaks
Stanse found a cut&pasted memory leak in pciehp_queue_pushbutton_work
and shpchp_queue_pushbutton_work. info is not freed/assigned on all
paths. Fix that.

Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:16:57 -08:00
Dominik Brodowski 3b7a17fcda resource/PCI: mark struct resource as const
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:16:57 -08:00
Dominik Brodowski b26b2d494b resource/PCI: align functions now return start of resource
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.

Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:16:56 -08:00
Rafael J. Wysocki 93177a748b PCI: Clean up build for CONFIG_PCI_QUIRKS unset
Currently, drivers/pci/quirks.c is built unconditionally, but if
CONFIG_PCI_QUIRKS is unset, the only things actually built in this
file are definitions of global variables and empty functions (due to
the #ifdef CONFIG_PCI_QUIRKS embracing all of the code inside the
file).  This is not particularly nice and if someone overlooks
the #ifdef CONFIG_PCI_QUIRKS, build errors are introduced.

To clean that up, move the definitions of the global variables in
quirks.c that are always built to pci.c, move the definitions of
the empty functions (compiled when CONFIG_PCI_QUIRKS is unset) to
headers (additionally make these functions static inline) and modify
drivers/pci/Makefile so that quirks.c is only built if
CONFIG_PCI_QUIRKS is set.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:21 -08:00
Jesse Barnes 3804259475 PCI hotplug: remove obsolete usage of get_bus_speed from rpaphp hotplug ops
No longer needed and causes build breakage.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:20 -08:00
Matthew Wilcox 9dfd97fe12 PCI: Add support for reporting PCIe 3.0 speeds
Add the 8.0 GT/s speed.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:19 -08:00
Matthew Wilcox 45b4cdd57e PCI: Add support for AGP in cur/max bus speed
Take advantage of some gaps in the table to fit in support for AGP speeds.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:19 -08:00
Matthew Wilcox 9be60ca049 PCI: Add support for detection of PCIe and PCI-X bus speeds
Both PCIe and PCI-X bridges report their secondary bus speed in their
respective capabilities.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:18 -08:00
Matthew Wilcox 3749c51ac6 PCI: Make current and maximum bus speeds part of the PCI core
Move the max_bus_speed and cur_bus_speed into the pci_bus.  Expose the
values through the PCI slot driver instead of the hotplug slot driver.
Update all the hotplug drivers to use the pci_bus instead of their own
data structures.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:17 -08:00
Matthew Wilcox 536c8cb49e PCI: Unify pcie_link_speed and pci_bus_speed
These enums must not overlap anyway, since we only have a single
pci_bus_speed_strings array.  Use a single enum, and move it to
pci.h.  Add 'SPEED' to the pcie names to make it clear what they are.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:17 -08:00
Matthew Wilcox f07852d644 PCI: Rewrite pci_scan_slot
The Alternate Routing-ID Interpretation capability allows a single device
to have up to 256 functions.  They can be populated sparsely, so the
current technique of scanning every eighth function is not guaranteed
to find them all.  By introducing a 'next_fn' function pointer, we can
use the linked list of functions in the ARI capability to scan all the
functions which exist.

We can then speed up the pci_scan_slot by skipping the scan of subsequent
devfns for PCIe devices which are the direct children of Root Ports or
Downstream Ports.  These devices are only permitted to implement device
0, unless they are ARI devices, in which case they'll be scanned by the
ARI code above.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
2010-02-22 16:15:16 -08:00
Alexander Duyck 7a0deb6bcd pci: add support for 82576NS serdes to existing SR-IOV quirk
This patch adds support for the 82576NS Serdes adapter to the existing pci
quirk for 82576 parts.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:33 -08:00
Jesse Barnes cf4c43dd43 PCI: Add pci_bus_find_ext_capability
For use by code that needs to walk extended capability lists before
pci_dev structures are set up.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <43F901BD926A4E43B106BF17856F07559FB80CFD@orsmsx508.amr.corp.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
2010-02-19 16:12:26 -08:00
Len Brown 0e2ecbaefd Merge branches 'bugzilla-14886', 'bugzilla-15000', 'bugzilla-15040', 'bugzilla-15108', 'pdc', 'hotplug-null-ref' and 'thinkpad' into release 2010-02-18 03:51:04 -05:00
David S. Miller 2bb4646fce Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-02-16 22:09:29 -08:00
Williams, Mitch A fb8a0d9d1b pci: Add SR-IOV convenience functions and macros
Add and export pci_num_vf to allow other subsystems to determine how many
virtual function devices are associated with an SR-IOV physical function
device.
Add macros dev_is_pci, dev_is_ps, and dev_num_vf to make it easier for
non-PCI specific code to determine SR-IOV capabilities.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-12 16:56:07 -08:00
H. Peter Anvin c85e4aae69 ibmphp: Rename add_range() to add_bus_range() to avoid conflict
Rename add_range() to add_bus_range() to avoid conflict with the
naming of the generic range manipulation functions.

LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
2010-02-10 17:45:09 -08:00