Commit Graph

75878 Commits

Author SHA1 Message Date
Johannes Berg a80f7c0b08 mac80211: introduce flush operation
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
 * before scanning sends the nullfunc frames
 * after scanning sends the nullfunc frames, if any
 * when going idle, to send any pending frames

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:54:51 -05:00
John W. Linville d30506e035 rtl8187: remove priv->mode
It is checked in add_interface, but there it is easily replaced with
a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

It is also checked in led_turn_on and led_turn_off, where I made the
substitutions as described above.  Of course, these checks seem to
have been incorrect since the driver was using NL80211_IFTYPE_MONITOR
to indicate no interface rather than NL80211_IFTYPE_UNSPECIFIED.
Anyway, I think these checks may be extraneous...?

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
John W. Linville 643aab6733 rtl8180: remove priv->mode
It is only checked in add_interface, and there it is easily replaced
with a check of priv->vif.  If that information should become necessary,
it is available in vif->type anyway.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
Gertjan van Wingerde 5122d89862 rt2x00: Cleanup chip handling helper functions.
Let each of them take a struct rt2x00_dev pointer as argument instead of
a mixture of struct rt2x00_chip and struct rt2x00_dev pointers.
Preparation for further clean ups in the rt2x00 chip handling, especially
for rt2800 devices.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:38 -05:00
Gertjan van Wingerde 73a2f1259e rt2x00: convert RT2800PCI_PCI and RT2800PCI_SOC Kconfig symbols to booleans.
There is no need for Kconfig symbols RT2800PCI_PCI and RT2800PCI_SOC to be
tristates, as they are only used to check whether RT2800 PCI or SOC support
is to be compiled in.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Gertjan van Wingerde ac394917f5 rt2x00: Let rt2800lib check CONFIG_RT2X00_LIB_USB instead of CONFIG_RT2800USB
rt2800lib currently checks whether RT2800USB is enabled in the configuration.
Strictly speaking this is not necessary, it only needs to know whether the
generic rt2x00usb library functions are available. Therefore check for
RT2X00_LIB_USB instead.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Gertjan van Wingerde 00e23ce219 rt2x00: Fix checks for rt2800 SOC support.
Fix checking for SOC support in rt2800pci. The wrong config (an unexisting
one) was checked.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:37 -05:00
Juuso Oikarinen 8f648c0003 wl1271: Prevent performing "join" before association
There is a minor bug in the code causing a "join" to be performed before
there is an intention to associate. Fix this.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen 04477bf095 wl1271: Check vif for NULL when indicating beacon-loss
Because the interface is started and the vif are created and destroyed
separately, there is a slim possibility beacon-loss indications occur while
there is no vif - causing a kernel-oops unless checked.

Add checking for the vif.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen 38ad2d87d4 wl1271: Add support for acx_pm_config
This acx configures host clock parameters in correspondence with the clock
request line - the settling time of the clock, and whether fast wake-up is
supported.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:36 -05:00
Juuso Oikarinen 71449f8d70 wl1271: Change booleans in struct wl1271 into a flags bitmask
For cleaner implementation, change the bunch of booleans in the struct wl1271
structure into a flags bitmask.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen 830fb67b8e wl1271: Fix supported rate management
Previously, only basic rates were used for data transmission - resulting in
reduced transfer rates. This patch takes enables the firmware to take advantage
of the full set of data rates supported by the AP.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen ec078d943b wl1271: Change rates configured for templates
Previously a "firmware chooses" value was used for the rates of all control
message templates set to the firmware. This resulted in a too high rate to be
chosen to transmit those messages. Change this by configuring a fixed low rate
for the templates.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen e0d8bbf0d2 wl1271: Add rudimentary ad-hoc support
This patch adds rudimentary a-hoc support for the driver. It will allow
setting up ad-hoc, and for other devices to scan and join. The beacon and probe
response template setting is slightly dirty, and need to be properly
implemented with support from mac80211. Also, the SSID is not configured to the
firmware - the FW will not be able to respond to probe requests autonomously.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen 26a63f6af5 wl1271: Remove beacon-loss-ind from PSM entry failure handling
Remove the beacon-loss indication to stack from PSM entry failure handling -
this will cause more problems than it will solve due to the design of the
mac80211.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:35 -05:00
Juuso Oikarinen 01ac17ecb6 wl1271: Add pre-power-on sleep
This patch adds a short delay before powering on the wl1271. Normally, it is
not needed, but if the wl1271 has been powered off shortly before, for reliable
firmware-booting this small stabilization delay is required.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen 9ccd921792 wl1271: Implement chipset boot retry
The wl1271 has a hardware bug which causes it to randomly (very infrequently)
to fail powering up properly. This patch implements retry for the chipset boot
sequence, to work around the hardware problem.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen af5e084b32 wl1271: prevent power save entry while not associated
The mac80211 sometimes requests power save entry while not associated - this
will cause problems, so prevent it if not associated. Go to powersave once
association is complete.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen 13f2dc52c6 wl1271: Fix event acknowledging functionality
In reference source, events are acknowledged separately - fix the driver to
do the same.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:34 -05:00
Juuso Oikarinen a6fe231361 wl1271: Use slow rates for association messages
While not associated, default the data rates to 1 and 2mbps, so that only
those rates will be used for association related message transfer. Once
associated, configure the full rate-set supported by the AP.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Juuso Oikarinen 018b171c40 wl1271: Remove smart reflex ACX
Remove the smart-reflex ACX - the associated parameters are now configured
in the radio parameters config.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Juuso Oikarinen 149e38789f wl1271: Configure smart-reflex paramter values.
Configure correct values to be used with the smart-reflex configuration of the
firmware.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Luciano Coelho 94210897e2 wl1271: use channel 1 when configuring the data path
In the data path configuration, one of the parameters is the channel.  We
have been setting it to wl->channel, which is not correct in this case.  This
channel has nothing to do with the channel we're currently tuned to, since it
is only used for calibration during this phase.  Hardcoded the channel to 1,
according to the reference driver.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:33 -05:00
Luciano Coelho 3ed8f2c614 wl1271: some new configuration values according to new reference
In the new reference driver, some of the firmware configuration values have
been changed.  This patch changes them in the wl1271 driver accordingly.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho 8cf5e8e509 wl1271: upload only the first 468 bytes from the NVS file
We were uploading the whole NVS file, but that is wrong, because the same
file also contains the initialization values.  For the latest firmwares, we
should upload only the initial 468 bytes from the file.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho 98b2a68473 wl1271: add gpio_power file in debugfs to power the chip on and off
Some debugging tools require the chip to be powered on before they can work.
With these tools, we shouldn't upload the firmware nor boot the firmware
ourselves, so this debufs file is provided.  It always contains the gpio
power setting (0 = off, 1 = on).  To change the power setting, just write 0
or 1 to the file.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho 1b38ea8858 wl1271: fix one typo in the rx_rssi_and_proc_compens values
There was a typo in one of the values in the rx_rssi_and_proc_compens elemt
of the Radio Parameters struct.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:32 -05:00
Luciano Coelho 6e92b416b0 wl1271: implement dco itrim parameters setting
Newer firmwares require the dco itrim parameters to be set during
initialization.  This patch implements the new ACX function and calls it.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho ac9b40fac6 wl1271: use the correct macro when setting the basic rates
We were using CONF_TX_RATE_MASK_ALL when calling wl1271_acx_rate_policies()
during init.  We should use WL1271_DEFAULT_BASIC_RATE_SET instead.  The
values are the same, but the latter is just the correct macro to use.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho bdcbbb947b wl1271: set null data template when BSSID is known
The call to wl1271_cmd_build_null_data() was missing when we got associated,
this was causing PS to fail.  This patch adds the call and now PS seems to
work.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:31 -05:00
Luciano Coelho cd264769f7 wl1271: check result code from the join command
We were not checking the return value from the call to wl1271_cmd_join().
Added a check to make things more reliable.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:30 -05:00
Luciano Coelho a2d0e3f130 wl1271: limit TX power to 25dBm for every channel
The wl1271 firmware supports maximun 25.5dBm, so the driver was returning
-EINVALID to anything above that.  This patch uses the channel max_power
option to limit the TX power to 25dBm.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:30 -05:00
Luciano Coelho 9cf25fed6a wl1271: remove workaround for disconnection
Now we're using a the idle information coming from mac80211 to decide when to
disconnect.  If we have joined (ie. we're listening to a channel), whenever
the interface goes to idle, we will issue a disconnect command.  So the
workaround to send a disconnect command before joining is not needed anymore.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:30 -05:00
Luciano Coelho c7f43e451b wl1271: use join command with dummy BSSID
When we need to change the channel before association, we have to send a join
command with a valid BSSID.  With this patch we use 0baddeadbeef as the
BSSID.  There are ongoing discussions with TI to get this done in a cleaner
way.

When we go back to idle, we issue a CMD_DISCONNECT to make sure the firmware
stops listening to the channel and cleans things up internally.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:30 -05:00
Luciano Coelho cf18be4467 wl1271: added radio parameters configuration values newer firmwares
Add new radio parameters for new structures based on firmware revision
6.1.0.0.288.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:29 -05:00
Luciano Coelho a3e84847b0 wl1271: update radio and general parameters values
There were some changes in the values we have to use for these settings.  This
patches updates them.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:29 -05:00
Luciano Coelho 76c0f8d396 wl1271: updated general parameters structure for newer firmwares
In revision 6.1.0.0.288 the general parameters structure has changed.  This
patch updates the driver code accordingly.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:29 -05:00
Luciano Coelho 937a67e75a wl1271: updated radio parameters structure for newer firmwares
In revision 6.1.0.0.288 the radio parameters structure has changed.  This
patch updates the driver code accordingly.

Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:28 -05:00
Larry Finger b02914af4d b43: Allow PIO mode to be selected at module load
If userencounter the "Fatal DMA Problem" with a BCM43XX device, and
still wish to use b43 as the driver, their only option is to rebuild
the kernel with CONFIG_B43_FORCE_PIO. This patch removes this option and
allows PIO mode to be selected with a load-time parameter for the module.
Note that the configuration variable CONFIG_B43_PIO is also removed.

Once the DMA problem with the BCM4312 devices is solved, this patch will
likely be reverted.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:28 -05:00
Lennert Buytenhek 7dc6a7a763 mwl8k: remove duplicate local per-vif copy of ieee80211_bss_conf
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:28 -05:00
Lennert Buytenhek 9747478295 mwl8k: remove unused mwl8k_vif::priv
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:27 -05:00
Lennert Buytenhek 89a91f4f4c mwl8k: fix up AP vs. STA firmware image receive descriptor handling
The receive descriptor ops that are currently marked as being for
8687 only are actually used for all STA firmware images, whereas the
receive descriptor ops marked as 8366 are only used on 8366 when an
AP firmware image is in use.

Rename the receive descriptor ops to reflect this, use the STA ops
unconditionally if the firmware image loaded reported the STA ready
code, and rename the mwl8k_device_info::rxd_ops member to ap_rxd_ops
to indicate that it should only be used if we are running on AP
firmware.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:27 -05:00
Lennert Buytenhek be695fc4f0 mwl8k: do rx/tx ring initialisation after loading firmware
Whether the firmware we have loaded is AP or STA firmware decides
which receive descriptor format we have to use.  Therefore, move
rx/tx ring initialisation to be after firmware loading.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:27 -05:00
Lennert Buytenhek 22be40d9c5 mwl8k: get rid of the struct mwl8k_firmware abstraction
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:26 -05:00
Lennert Buytenhek 647ca6b01a mwl8k: add 2.4GHz channels 12, 13 and 14
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:26 -05:00
Lennert Buytenhek 49eb691c8f mwl8k: initialize the mwl8k_info_tbl table using the MWL* enums
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:26 -05:00
Lennert Buytenhek e0493a8dd6 mwl8k: inline qos field manipulation functions
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:25 -05:00
Lennert Buytenhek 74726e7292 mwl8k: get rid of the AMSDU check in the transmit path
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:25 -05:00
Lennert Buytenhek 99200a992e mwl8k: hw is never NULL in mwl8k_set_radio_preamble()
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:24 -05:00
Lennert Buytenhek 55489b6ed6 mwl8k: firmware command code cleanup
Sort firmware commands by command code, get rid of the 802_11 substring
in all command names, and make sure that the command functions match the
firmware command names.

Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28 16:31:24 -05:00