Commit Graph

4 Commits

Author SHA1 Message Date
Krishna Gudipati 10a0737924 [SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
- If flash controller is halted unconditionally, this results in
  illegal write access to flash controller register domain. Since
  flash controller registers are only accessible once s_clk is started
  - added logic to check for WGN status and halt flash controller only
  if it is already running.
- Added check to wait for flash controller halt to be completed before
  proceeding with s_clk/l_clk initializations.
- Removed unnecessary reset logic for PMM 1T memory and moved memory
  initialization after flash access enable.
- Disable Brocade-1860 asic MBOX interrupt before PLL initialization.
- Remove reset enable for S_CLK/L_CLK after both PLL initializations
  are complete.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 16:59:59 -05:00
Krishna Gudipati 8b070b4a02 [SCSI] bfa: Brocade-1860 Fabric Adapter 16Gbs support and flash controller fixes.
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
  when asic blck is programmed flash controller's continuous access
  blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
  initialization, since not doing so will cause LPU to be
  uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 15:50:50 -05:00
Krishna Gudipati 775c7742ad [SCSI] bfa: IOC and PLL init changes for Brocade-1860 Fabric Adapter.
- Introduced IOC poll mechanism which replaces current interrupt
  based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
  register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
  1. Use the queue_process flag to see if iocfc configuration is done
     in INTX mode.
  2. Split the MSIX handler installation in two - one for IOC intr
     handler and the other for cpe/rme queue handler - and delay
     assigning queue handlers until iocfc config is done in MSIX mode.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 15:46:19 -05:00
Krishna Gudipati 111892082e [SCSI] bfa: Brocade-1860 Fabric Adapter Hardware Enablement
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
  only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
  firmware response.
- Removed queue register offset initializations and added register offsets
  to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
  mailbox interfaces.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 15:31:31 -05:00