We can only use the madc to check for 'ac' availability if the madc has
been compiled in. If not: assume always using USB.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neil@brown.name>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Access to the BQ24190's configurable charge type property (none, trickle,
fast) is being masked by an incorrect power_supply_property entry. After
applying this patch a new 'charge_type' property will appear in the
bq24190-charger sysfs folder backed up by getters/setters already
present in the driver.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The USB Battery Charging spec (BC1.2) suggests a dedicated
charging port can deliver from 0.5 to 5.0A at between 4.75 and 5.25
volts.
To choose the "correct" current voltage setting requires a trial
and error approach: try to draw current and see if the voltage drops
too low.
Even with a configured Standard Downstream Port, it may not be possible
to reliably pull 500mA - depending on cable quality and source
quality I have reports of charging failure due to the voltage dropping
too low.
To address both these concerns, this patch introduce incremental
current setting.
The current pull from VBUS is increased in steps of 20mA every 100ms
until the target is reached or until the measure voltage drops below
4.75V. If the voltage does go too low, the target current is reduced
by 20mA and kept there.
This applies to currents selected automatically, or to values
set via sysfs. So setting a large value will cause the maximum
available to be used - up to the limit of 1.7A imposed by the
hardware.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This allows AC charging to be turned off, much like usb charging.
"continuous" mode is not available though.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add a 'continuous' option for usb charging which enables
the "linear" charging mode of the twl4030.
Linear charging does a good job with not-so-reliable power sources.
Auto mode does not work well as it switches off when voltage drops
momentarily. Care must be taken not to over-charge.
It was used with a bike hub dynamo since a year or so. In that case
there are automatically charging stops when the cyclist needs a break.
Original-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'off' or 'auto' to
/sys/class/power/twl4030_usb/mode
will now enable or disable charging from USB port. Normally this is
enabled on 'plug' and disabled on 'unplug'.
Unplug will still disable charging. 'plug' will only enable it if
'auto' if selected.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'max_current' sysfs attributes are created which allow the
max to be set.
Whenever a current source changes, the default is restored.
This will be followed by a uevent, so user-space can decide to
update again.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 charger has two current sources, 'USB' and 'AC'
(presumably "Accessory Charger" because it isn't Alternating Current).
If 'AC' is providing current, we should set the current limit
differently to when it isn't (and so USB is used).
So split 'cur' into 'usb_cur' and 'ac_cur' and use accordingly.
Now we must review the current setting on any interrupt or USB
event which might indicate that the charger-source has changed.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 allows control of the incoming current.
Part of this control is a 'CGAIN' setting which doubles
the range for half the precision. This control affects
several different current setting, so all need to be updated
at once when CGAIN is changed.
With this patch, all of these current setting are managed
by the driver, but most are left at their default settings.
The current drawn is set to 500mA if the allow_usb module parameter is
set, and to 100mA otherwise.
More fine control will appear in later patches.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
We will need this calculation in other places, so
create functions to map between register value and uA value.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The usb phy driver already determines when VBUS is available,
so repeating the test in the charger driver is pointless duplication.
On probe, process the last event from the phy, and from then on,
do whatever the phy tells us without double-checking.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Now that twl4030_bci_probe can safely return -EPROBE_DEFER,
do so when devm_usb_get_phy_by_node returns that error.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Drivers using module_platform_driver_probe cannot return
EPROBE_DEFER from the probe function, which makes them rather useless
these days...
Convert to module_platform_driver() so EPROBE_DEFER can be used.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The twl4030 usb phy needs to be active while we are using
the USB VBUS as a current source for charging.
In particular, the usb3v1 regulator must be enabled and the
PHY_PWR_PHYPWD bit must be set to keep the phy powered.
commit ab37813f40
twl4030_charger: Allow charger to control the regulator that feeds it
gave the charger control over the regulator, but didn't resolve
the PHY_PWR_PHYPWD issue.
Now that both of these are controlled by runtime_pm in
phy-twl4030-usb, we can simply take a runtime_pm reference to the USB
phy whenever the charger wants to use it as a current source.
So this patch reverts the above commit, and adds the necessary
runtime_pm calls.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
For compatibility between board code and DT, set battery name to same value.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant sysfs binary file boundary check while
reading eeprom content from userspace, the check is done on caller
side in fs/sysfs/file.c, if binary attribute size is not zero.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant calculation of left space on eeprom while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The change removes redundant sysfs binary file boundary checks while
reading or writing "param_eeprom" or "user_eeprom", the checks are not
needed, since this task is done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use managed resource functions like devm_kasprintf and
devm_power_supply_register in bq24735_charger_probe. To be
compatible with the change, replace various gotos by direct
returns and drop unneeded labels.
Also, remove bq24735_charger_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Including ARM related header file cause build failure
in i386 build because COMILE_TEST also involve building
zx driver. Remove the unnecessary include file.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Remove space before tab.
Remove unnecessary line continuations.
Add braces to else statement.
Remove unnecessary parentheses.
Remove unneeded blank lines.
Remove unnecessary 'out of memory' message.
Add missing line after declarations.
Change use of printk to pr_err.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix the alignment of function parameters on new lines.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Shorted lines over 80 characters long by reducing tab count.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add the manufacturer property to the bq27x00 driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Register with kernel restart handler instead of setting arm_pm_restart
directly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Make it possible to set the name of the supply from the devicetree.
Like other power supply drivers just use the node name. This makes
the code smaller as well, as it doesn't need to allocate memory to
hold the name and allocate a unique ID.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Final allocations/registrations are now managed by devres.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This simplifies the error paths.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch introduces a new compatible string: "atmel,sama5d3-rstc" and
new reset function for sama5d3 and later chips.
As in sama5d3 or later chips, we don't have to shutdown the DDR
controller before reset. Shutdown the DDR controller before reset is a
workaround to avoid DDR signal driving the bus, but since sama5d3 and
later chips there is no such a conflict.
So in this patch:
1. the sama5d3 reset function only need to write the rstc register
and return.
2. we can remove the code related with sama5d3 DDR controller as
we don't use it at all.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Charging events this patch refers to are:
- charger is connected to/disconnected from the power source
- battery is reconnected to the charger, after it was absent.
When the charger is connected to/disconnected from the power source, CHRVPI
interrupt occurs and PWR_RDY bit is either set or cleared. PWR_RDY bit is
updated after 1-2 seconds CHRVPI interrupt has occurred.
power_supply_changed() should be called after PWR_RDY bit is updated.
/sys/class/power_supply/rt9455-charger/online file displays the value of
PWR_RDY bit.
This way, if the userspace is notified that a charging event has occurred
and the userspace reads /sys/class/power_supply/rt9455-charger/online file,
this file is properly updated when the userspace reads it.
This is the reason why power_supply_changed() is called in
rt9455_pwr_rdy_work_callback(), instead of being called in interrupt
handler.
Since no interrupt is triggered when the battery is reconnected to the
charger, the userspace is never notified that the battery is reconnected.
This is why power_supply_changed() is called in
rt9455_max_charging_time_work_callback(), so that the userspace is notified
that the battery is reconnected.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WLBw
-----END PGP SIGNATURE-----
Merge tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_platform_driver replacement from Paul Gortmaker:
"Replace module_platform_driver with builtin_platform driver in non
modules.
We see an increasing number of non-modular drivers using
modular_driver() type register functions. There are several downsides
to letting this continue unchecked:
- The code can appear modular to a reader of the code, and they won't
know if the code really is modular without checking the Makefile
and Kconfig to see if compilation is governed by a bool or
tristate.
- Coders of drivers may be tempted to code up an __exit function that
is never used, just in order to satisfy the required three args of
the modular registration function.
- Non-modular code ends up including the <module.h> which increases
CPP overhead that they don't need.
- It hinders us from performing better separation of the module init
code and the generic init code.
So here we introduce similar macros for builtin drivers. Then we
convert builtin drivers (controlled by a bool Kconfig) by making the
following type of mapping:
module_platform_driver() ---> builtin_platform_driver()
module_platform_driver_probe() ---> builtin_platform_driver_probe().
The set of drivers that are converted here are just the ones that
showed up as relying on an implicit include of <module.h> during a
pending header cleanup. So we convert them here vs adding an include
of <module.h> to non-modular code to avoid compile fails. Additonal
conversions can be done asynchronously at any time.
Once again, an unused module_exit function that is removed here
appears in the diffstat as an outlier wrt all the other changes"
* tag 'module-builtin_driver-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
drivers/clk: convert sunxi/clk-mod0.c to use builtin_platform_driver
drivers/power: Convert non-modular syscon-reboot to use builtin_platform_driver
drivers/soc: Convert non-modular soc-realview to use builtin_platform_driver
drivers/soc: Convert non-modular tegra/pmc to use builtin_platform_driver
drivers/cpufreq: Convert non-modular s5pv210-cpufreq.c to use builtin_platform_driver
drivers/cpuidle: Convert non-modular drivers to use builtin_platform_driver
drivers/platform: Convert non-modular pdev_bus to use builtin_platform_driver
platform_device: better support builtin boilerplate avoidance
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Caused by commit 843735b788 ("power: axp288_charger: axp288 charger
driver") from the battery tree interacting with commit 046050f6e6
("extcon: Update the prototype of extcon_register_notifier() with enum
extcon") from the extcon tree.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
* New charger drivers: BQ24257, BQ25890, AXP288, RT9455
* MAX17042 battery: add health & temperature support
* BQ2415x charger: add ACPI support
* misc. fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=192M
-----END PGP SIGNATURE-----
Merge tag 'for-4.2' of git://git.infradead.org/battery-2.6
Pull power supply and reset updates from Sebastian Reichel:
- new charger drivers: BQ24257, BQ25890, AXP288, RT9455
- MAX17042 battery: add health & temperature support
- BQ2415x charger: add ACPI support
- misc fixes and cleanups
* tag 'for-4.2' of git://git.infradead.org/battery-2.6: (32 commits)
power_supply: Correct kerneldoc copy paste errors
wm831x_power: Fix off-by-one at free_irq()
power_supply: rt9455_charger: Fix error reported by static analysis tool
power_supply: bq24257: use flags argument of devm_gpiod_get
power_supply: bq25890: use flags argument of devm_gpiod_get
sbs-battery: add option to always register battery
power: Add devm_power_supply_get_by_phandle() helper function
power_supply: max17042: Add OF support for setting thresholds
power_supply: sysfs: Bring back write to writeable properties
power_supply: rt9455_charger: Check if CONFIG_USB_PHY is enabled
power: reset: gpio-restart: increase priority slightly
power_supply: bq25890: make chip_id int
power_supply: Add support for Richtek RT9455 battery charger
Documentation: devicetree: Add Richtek RT9455 bindings
of: Add vendor prefix for Richtek Technology Corporation
power_supply: 88pm860x_charger: Do not call free_irq() twice
power: bq24190_charger: Change first_time flag reset condition
power: axp288_charger: axp288 charger driver
power: max17042_battery: add HEALTH and TEMP_* properties support
power_supply: Add support for TI BQ25890 charger chip
...
This file depends on Kconfig options all of which are a bool, so
we use the appropriate registration function, which avoids us
relying on an implicit inclusion of <module.h> which we are
doing currently.
While this currently works, we really don't want to be including
the module.h header in non-modular code, which we'd be forced
to do, pending some upcoming code relocation from init.h into
module.h. So we fix it now by using the non-modular equivalent.
Cc: Sebastian Reichel <sre@kernel.org>
Acked-By: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
An error handling in wm831x_power_probe() mistakenly frees a failed-to-
request irq as well as other irqs. I added missing decrement of the loop
counter.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The result of container_of macro cannot be NULL, so there is no need to
check whether info is NULL.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Simplify driver accordingly. Furthermore this is one caller less that
stops us making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Commit a22b41a31e ("sbs-battery: Probe should try talking to the
device") introduced a step in probing the SBS battery, that tries to
talk to the device before actually registering it, saying:
this driver doesn't actually try talking to the device at probe
time, so if it's incorrectly configured in the device tree or
platform data (or if the battery has been removed from the system),
then probe will succeed and every access will sit there and time
out. The end result is a possibly laggy system that thinks it has a
battery but can never read status, which isn't very useful.
Which is of course reasonable. However, it is also very well possible
for a device to boot up on wall-power and be connected to a battery
later on. This is a scenario that the driver supported before said patch
was applied, and even easily achieved by booting up with the battery
attached and removing it later on. sbs-battery's 'present' sysfs file
can be used to determine if the device is available or not.
So with automated device detection lacking for now, in some cases it is
possible that one wants to register a battery, even if none are attached
at the moment. To facilitate this, add a module parameter that can be
used to configure forced loading module loading time. If set, the battery
will always be registered without checking the sanity of the connection.
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds a resource-managed version of the
power_supply_get_by_phandle() function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The commit edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.
This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab0559 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The fix for NULL pointer exception related to calling uevent for not
finished probe caused to set all writeable properties as non-writeable.
This was caused by checking if property is writeable before the initial
increase of power supply usage counter and in the same time using
wrapper over property_is_writeable(). The wrapper returns ENODEV if the
usage counter is still 0.
The call trace looked like:
device probe:
power_supply_register()
use_cnt = 0;
device_add()
create sysfs entries
power_supply_attr_is_visible()
power_supply_property_is_writeable()
if (use_cnt == 0) return -ENODEV;
use_cnt++;
Replace the usage of wrapper with direct call to property_is_writeable()
from driver. This should be safe call during device probe because
implementations of this callback just return 0/1 for different
properties and they do not access any of the driver's internal data.
Fixes: 8e59c7f234 ("power_supply: Fix NULL pointer dereference during bq27x00_battery probe")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
If CONFIG_USB_PHY is not enabled, struct notifier_block is not defined and
compilation fails. Therefore, the functions that process USB event
notifications are defined only if CONFIG_USB_PHY is enabled.
There is no need to define these functions if CONFIG_USB_PHY is not
enabled, since no USB notifications are received in this case.
Also, since rt9455_set_boost_voltage_before_boost_mode() function is
called only if USB_EVENT_ID notification is received, this function should
also be defined only if CONFIG_USB_PHY is enabled.
Signed-off-by: Anda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
gpio-restart uses a priority of 128 and currently most soc-level restart
mechanisms use the same - with some exceptions even using 192.
But while the soc-level restarts are provided by the soc itself,
gpio-restarts will most of the time be board-specfic and be used
when some special board condition makes the soc-level restart
only a second choice.
The problem at hand manifested itself on the rk3288-veyron devices.
While the soc-level restart can sucessfully restart all other rockchip
boards I have, the veyron devices use an external restart mechanism that
seems to not only reset the soc but also some external needed components.
With both restart handlers having priority 128 in my tests the soc-specific
variant took precedent in all cases. While it could restart the soc
sucessfully in all cases, firmware then got an issue when talking to an
external component, resulting in the device being put into recovery mode.
So, give the board-specific restart handler a slight push and move it
to priority 129 to make it more important than the generic soc-specific
restart-handler.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
NeilBrown
Andreas Dannenberg
Geert Uytterhoeven
Javier Martinez Canillas
Pavel Machek
Pali Rohár
Vladimir Zapolskiy
Vaishali Thakkar
Jun Nie
Andrew F. Davis
Mike Looijmans
NeilBrown
Josh Wu
Krzysztof Kozlowski
Anda-Maria Nicolae
Linus Torvalds
Stephen Rothwell
Bjorn Andersson
Paul Gortmaker
Takeshi Yoshimura
Uwe Kleine-König
Frans Klaver
Hans de Goede
Heiko Stübner