There was a use after free in __unregister_request that would trigger
whenever the request map held the last reference. This appears to have
triggered an oops during 'umount -f' when requests are being torn down.
Signed-off-by: Sage Weil <sage@newdream.net>
For the boot, enable_mmu() is called from setup_arch() but we don't call
setup_arch() for any of the other cpus. So turn on the non-boot cpu's
mmu inside of start_secondary().
I noticed this bug on an SMP board when trying to map I/O memory
(smsc911x registers) into the kernel address space. Since the Address
Translation bit in MMUCR wasn't set, accessing the virtual address where
the smsc911x registers were supposedly mapped actually performed a
physical address access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ensure that the aux table is properly initialized, even when optional
features are missing. Without this, the FDPIC loader did not work.
Signed-off-by: Andrew Stubbs <ams@codesourcery.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is ipv6 variant of the commit 5e016cbf6.. ("ipv4: Don't drop
redirected route cache entry unless PTMU actually expired")
by Guenter Roeck <guenter.roeck@ericsson.com>.
Remove cache route entry in ipv6_negative_advice() only if
the timer is expired.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a20b2a44ec.
As requested by David Fries. This makes CDROMs which are slave drives
on a ribbon without a master disappear and causes other similar kinds
of badness.
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Stephen Rothwell.
drivers/net/tulip/uli526x.c: In function 'uli526x_rx_packet':
drivers/net/tulip/uli526x.c:861: warning: assignment makes pointer from integer without a cast
Signed-off-by: David S. Miller <davem@davemloft.net>
do_logfs_journal_wl_pass() must call freeseg(), thereby clear
PagePrivate on all pages of the current journal segment.
Signed-off-by: Joern Engel <joern@logfs.org>
A comment in the old code read:
/* The math in this function can surely use some love */
And indeed it did. In the case that area->a_used_bytes is exactly
4096 bytes below segment size it fell apart. pad_wbuf is now split
into two helpers that are significantly less complicated.
Signed-off-by: Joern Engel <joern@logfs.org>
The comment was correct, so make the code match the comment. As the
new comment indicates, we might be able to do a little less work. But
for the current -rc series let's keep it simple and just fix the bug.
Signed-off-by: Joern Engel <joern@logfs.org>
A CPU has VFPv3 hardware if the FPSID[19:16] bits are 2 or more.
Currently Linux was only checking for 3 or more.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using VT6410/6415/6330 chips on some VIA's platforms, the HDD
connection to VT6410/6415/6330 cannot be detected.
It is because the driver detects wrong via_isa_bridge ID, and then
causes this issue to happen.
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use set_cpus_allowed_ptr rather than set_cpus_allowed.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2;
@@
- set_cpus_allowed(E1, cpumask_of_cpu(E2))
+ set_cpus_allowed_ptr(E1, cpumask_of(E2))
@@
expression E;
identifier I;
@@
- set_cpus_allowed(E, I)
+ set_cpus_allowed_ptr(E, &I)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is quite similar to b39fe41f48
though said registers are not even documented as 64-bit registers
- as opposed to the initial TxDescStartAddress ones - but as single
bytes which must be combined into 32 bits at the MMIO read/write
level before being merged into a 64 bit logical entity.
Credits go to Ben Hutchings <ben@decadent.org.uk> for the MAR
registers (aka "multicast is broken for ages on ARM) and to
Timo Teräs <timo.teras@iki.fi> for the MAC registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs:
*add new id (Allied Telesis LM33-PCM-T Lan&Modem multifunction card)
*use PROD_ID for LA-PCM.(because LA-PCM and LM33-PCM-T use the same MANF_ID).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Round-robin (mode 0) does nothing to ensure that any multicast traffic
originally destined for the host will continue to arrive at the host when
the link that sent the IGMP join or membership report goes down. One of
the benefits of absolute round-robin transmit.
Keeping track of subscribed multicast groups for each slave did not seem
like a good use of resources, so I decided to simply send on the
curr_active slave of the bond (typically the first enslaved device that
is up). This makes failover management simple as IGMP membership
reports only need to be sent when the curr_active_slave changes. I
tested this patch and it appears to work as expected.
Originally reported by Lon Hohberger <lhh@redhat.com>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Lon Hohberger <lhh@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qla1280 driver acquires its firmware via udev. During boot the firmware
is located in the initrd. If, after root is mounted, the adapter needs to
reload firmware (host reset), the firmware load may fail if the root device
is on the adapter being reset. This patch modifies qla1280 to retain the
firmware loaded via the initial request_firmware() for use during error
recovery.
[jejb: fix up checkpatch issues]
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All of the SCSI transport classes are suddenly spitting lockdep
warnings. According to Eric Biderman this is because lockdep needs
static initialisers and the attribute container way of doing things
end up with dynamic sysfs attributes. Fix this by calling
sysfs_attr_init which sets the lockdep key correctly.
Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On newer kernels users of advansys module are reporting system hang when
trying to load it without firmware files present. After looking closely
at description on https://qa.mandriva.com/show_bug.cgi?id=53220, I think
this is related to commit "[SCSI] advansys: use request_firmware". The
problem is that after switch to request_firmware, asc_dvc->err_code
isn't being set when firmware files aren't found or loading fails.
err_code is used by the driver to judge if there was a fatal error or
not, as can be seen for example on advansys_board_found, which will only
return -ENODEV when err_code is set. Because err_code isn't being set
when request_firmware fails, this is a change of behaviour of the code
before request_firmware addition, making it continue to load and it
fails later as the firmware wasn't really loaded.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fix prevents application path from sending get-firmware-state mbx command
during as isp reset.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
On specific platforms, MSI is unreliable on some of the QLA24xx chips, resulting
in fatal I/O errors under load, as reported in <http://bugs.debian.org/572322>
and by some RHEL customers.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The logic is changed to detect this condition based on following
1) both module parameters are off (ql2xmaxqueues and ql2xmultique_tag).
2) both module parameters are on (ql2xmaxqueues and ql2xmultique_tag).
3) The HBA does not support multi queue.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Checks should only be done for NPIV-capable ISPs. Original code
could result in PORT_UPDATEs being missed on non-NPIV-capable
ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We now enable/disable "Additional Receive Credits" in f/w based on nvram
parameter "Extended_BB_Credits" bit (i.e. Enhanced-Features: at offset 0x196).
This is applicable only for GEN2 CNAs.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
blk_end_request doesn't complete a bidi request
successfully
The unfinished request eventually triggers a panic in
timeout handling routine fc_bsg_job_timeout as
req->special is NULL
Use blk_end_request_all to end the request unconditionally
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We could be failing/stopping a connection due to libiscsi starting
recovery/cleanup, but the xmit path or scsi eh thread path
could be dropping the connection at the same time.
As a result the session->state gets set to failed instead of in
recovery. We end up not blocking the session
and so the replacement timeout never gets started and we only end up
failing the IO when scsi_softirq_done sees that the
cmd has been running for (cmd->allowed + 1) * rq->timeout secs.
We used to fail the IO right away so users are seeing a long
delay when using dm-multipath. This problem was added in
2.6.28.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports
seen at half duplex. This had the effect of overriding user set values
on link change/reset. Testing shows that adjusting only the timeout
factor is sufficient to prevent Tx hang reports at half duplex.
This patch removes all instances of tx_queue_len in the driver.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cache is unresolved, c->mf[6]c_parent is set to 65535 and
minvif, maxvif are not initialized, hence we must avoid to
parse IIF and OIF.
A second problem can happen when the user dumps a cache entry
where a VIF, that was referenced at creation time, has been
removed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the offline diagnostic tests check to see if any VFs are
online. If so then only run the link test. This is necessary because
the VFs running in guest VMs aren't aware of when the PF is taken
offline for a diagnostic test. Also put a message to the system log
telling the system administrator to take the VFs offline manually if
(s)he wants to run a full diagnostic. Return 1 on each of the tests
not run to alert the user of the condition.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igb was previously checking the wrong bits in the MANC register to determine
if managability was enabled. As a result it was incorrectly powering down and
resetting the phy when it didn't need to.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings:
be_ethtool.c:493: warning: integer constant is too large for 'long' type
be_ethtool.c:493: warning: integer constant is too large for 'long' type
Signed-off-by: Zhitong Wang <zhitong.wangzt@alibaba-inc.com>
Acked-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new flag MSG_WAITFORONE for the recvmmsg() syscall.
When this flag is specified for a blocking socket, recvmmsg()
will only block until at least 1 packet is available. The
default behavior is to block until all vlen packets are
available. This flag has no effect on non-blocking sockets
or when used in combination with MSG_DONTWAIT.
Signed-off-by: Brandon L Black <blblack@gmail.com>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the first superblock is wrong and the second gets written, there
will still be a mismatch on next mount. Write both to make sure they
match.
Signed-off-by: Joern Engel <joern@logfs.org>
Intel SSDs have a limit of 0xffff as queue_max_hw_sectors(q). Such a
limit may make sense from a hardware pov, but it causes bio_alloc() to
return NULL.
Signed-off-by: Joern Engel <joern@logfs.org>
This patch avoids unbalanced enable/disable messages for the DMA
interrupts when running the 5200 platform SCLPC/BestComm driver in DMA
mode.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Define a binding for embedding a QE firmware blob into the device tree. Also
define a new property for the QE node that links to a firmware node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
NOPs within the property section are skipped, but NOPs between
OF_DT_END_NODE and OF_DT_BEGIN_NODE were not. My firmware NOPs out
entire nodes depending on various environment parameters.
of_scan_flat_dt already handles NOP more generally.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
This patch removes all instances of tx_queue_len in the driver.
Originally reported and patched by Franco Fichtner
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sage Weil
Matt Fleming
Andrew Stubbs
Julia Lawall
Yusuke Goda
YOSHIFUJI Hideaki / 吉藤英明
David S. Miller
Joern Engel
Catalin Marinas
JosephChan@via.com.tw
Francois Romieu
Ken Kawasaki
Andy Gospodarek
Michael Reed
James Bottomley
Herton Ronaldo Krzesinski
Giridhar Malavali
Santosh Vernekar
Ben Hutchings
Michael Hernandez
Andrew Vasquez
Sarang Radke
Mike Christie
Rob Landley
Joe Perches
Emil Tantilov
Nicolas Dichtel
Greg Rose
Alexander Duyck
wzt wzt
Brandon L Black
Roman Fietze
Timur Tabi
Jason Gunthorpe
Pavel Emelyanov