This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
When using CP15 cache operations (c7), we make sure that Rd (r0)
is actually 0 as ARM 926 TRM is saying.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For power management at91_pm_enter() routine, use the cpu_do_idle() for a
rock solid "wait for interrupt" implementation.
For AT91SAM9 ARM 926 based chips, we can exceed the cache line length as
we can access RAM even while in self-refresh mode.
We keep plain access to CP15 for at91rm9200 as this feature is not
available: instructions have to be in a single cache line.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.
For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().
Rename at91sam9g20_reset.S to generalize to several chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system
Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The patch below updates broken web addresses in the arch directory.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
According to Atmel, their 926T processors (AT91 post RM9200) requires
'Wait for Interrupt' mode be entered right after disabling the processor clock
in order to minimise current consumption when idle, so do both provided we're
not running on a 920T (an RM9200).
Furthermore, get rid of the #ifndef CONFIG_DEBUG_KERNEL, since arch_idle()
can be turned off completely with the kernel parameter 'nohlt'.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many Atmel SOC are embedding a MACB controller. This patch removes the long
dependency line for this Atmel MACB ethernet driver configuration entry.
The HAVE_NET_MACB configuration option is located in the net Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: David Miller <davem@davemloft.net>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
The simpler AT91x40 processors do not have the same power management
controller as the new AT91 devices. They do have a simpler power
controller module that we can use to disable the CPU clock at idle
time. Add code to support that.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MTD nand driver for Atmel chips is atmel_nand and not at91_nand anymore.
Change wrong configuration variables that were remaining.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Today the board use 2 machines id AT91SAM9G45EKES and AT91SAM9M10G45EK
now will use only AT91SAM9M10G45EK.
The other boards revision will be specified via system_rev.
for 9g45ekes, m10g45ekes and m10g45ek boards and revisions
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds support for Flexibity Connect platform from
http://www.flexibity.com/ (AT91SAM9260 based).
Signed-off-by: Maxim Osipov <maxim.osipov@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use a correct udelay value to get bus speed around 100KHz. The udelay
value was most likely copied from the older devices, but the 9g45
is signicantly faster (400MHz, DDR, ..), so a udelay of 2 gives a
bus speed of around 190KHz, which is too fast for some devices.
A udelay value of 5 gives a bus speed of around 90KHz here.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sd/mmc data structure is not used if SPI is selected. The configuration
of PIO on the board prevent from using both interfaces at the same time
(board dependent).
Remove the warnings at compilation time adding a preprocessor condition.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add information in dm9000 mac/phy chip initialization:
- irq resource details
- platform data details
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Without this patch you will not be able to register the first block
because of the second association call on at91_add_device_tc().
Signed-off-by: Fabian Godehardt <fg@emlix.com>
[nicolas.ferre@atmel.com: change tcb1_clk to fake child clock of tcb0_clk]
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
While registering clock allow to set parent clock other
than mck. It is useful for clocks than can be seen as
child clock of a peripheral.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 12/19] ARM: cam60: don't use __init for cam60_spi_{flash_platform_data,partitions}
Date: Thu, 5 Aug 2010 16:08:46 +0200
Message-Id: <1281017333-5563-12-git-send-email-u.kleine-koenig@pengutronix.de>
These two structs are referenced by cam60_spi_devices. The latter is
copied at init time to kmalloced memory and so the copy isn't freed after
booting. So it must not contain references to .init memory.
This isn't noticed by modpost as cam60_spi_devices is in .init.data, too.
Noticed-and-Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cam60_spi_devices is passed to at91_add_device_spi which calls
spi_register_board_info. The latter makes a copy of it, so living in
.init.data is OK.
This fixes the following warning in cam60_defconfig:
WARNING: vmlinux.o(.data+0x2a00): Section mismatch in reference from the variable cam60_spi_devices to the (unknown reference) .init.data:(unknown)
The variable cam60_spi_devices references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the vbus signal to optionally use polling. This is required if
the vbus signal is connected to an non-interrupting io expander for
example. If vbus is in polling mode, then it is assumed that the vbus
gpio may sleep. Also add an option to have vbus be an active low
signal. Both options are set in the platform data for the device.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Bluewater Systems Snapper 9260/9G20 modules
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add definition for NR_BUILTIN_GPIO for AT91 family
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This rework allows to address tow memory controllers. AT91SAM9263 and
AT91SAM9G45 family have tow SDRAM or DDR/SDRAM controllers. Power management
should take care of this.
This patch modify the way RAM IP header files are implemented to allow
access to registers of both controllers ; it also adds some macros.
We also modify the power management files to use those modified header files.
Slow clock (assembly) and regular power management functions are synchronized
for setting of RAM self-refresh procedure:
(lpr & ~AT91_DDRSDRC_LPCB) | AT91_DDRSDRC_LPCB_SELF_REFRESH
Note that AT91RM9200 is not impacted by this modification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the basic support for at91sam9g46, at91sam9m10 and at91sam9m11. Those
are just very basic cpu macros and clock definition.
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/board-sam9m10g45ek.c: mach/hardware.h is included more than once
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Final version of the patch that adds support for RS485 communications to the atmel_serial driver.
The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.
Many people collaborated to improve and test the code:
Tested-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: Bernhard Roth <br@pwrnet.de>
Reviewed-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Rick Bronson <rick@efn.org>
Signed-off-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the processor clock when the CPU is idle.
This saves much more power than merely entering 'Wait for Interrupt' mode.
Since JTAG-debugging doesn't work when the processor clock is switched off,
make it conditional on CONFIG_DEBUG_KERNEL.
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bit in the at91sam9g10 identification number changed between Engineering
Sample and final product. This patch will identify both as being at91sam9g10.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both boards share the same board file, as the PortuxG20 is basically an
SBC based on the Stamp9G20.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Julien Langer <julien.langer@gmail.com>
AT91: when turning off the PLLs during suspend, don't wait for the lock
flag to be set. Previously the code would always run into the loop
limitation of 1000 iterations because the flag is never set when turning
the PLLs off.
Comments from Anders Larsen:
(in http://marc.info/?l=linux-kernel&m=127058929724193&w=2)
Signed-off-by: Julien Langer <julien.langer@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
at91 slow-clock resume: Don't wait for a disabled PLL to lock.
We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
