This reverts commit 555b1b651a.
Let's try this again for 3.13. It's required for proper
interaction with alsa. Was disabled previously in 3.12
to be on the safe side since it caused problems on older
asics.
The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.
However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).
Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.
Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.
Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.
Example affected EDID from Onkyo TX-SR674 specifying 192kHz stereo
support and 96kHz 8-channel support (and other 8-channel compressed
formats):
00ffffffffffff003dcb010000000001
ffff0103800000780a0dc9a057479827
12484c00000001010101010101010101
010101010101011d8018711c1620582c
2500c48e2100009e011d007251d01e20
6e285500c48e2100001e000000fc0054
582d53523637342020202020000000fd
00313d0f2e08000a202020202020019b
02032f724f8504030f0e07069413121e
1d1615012f097f070f1f071707503707
503f07c0834f000066030c00ffff808c
0ad08a20e02d10103e9600c48e210000
18011d80d0721c1620102c2580c48e21
00009e011d00bc52d01e20b8285540c4
8e2100001e8c0ad090204031200c4055
00c48e210000180000000000000000a8
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Andre Heider <a.heider@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Use the driver calculated CTS and N values rather than
having hardware generate them. This allows us to use
the modeline pixel clock rather than the actual pll clock
when setting up the dto for audio. Fixes problems with
audio playback rate on certain asics if the pll clock
does not match the pixel clock exactly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the hw generated values rather than calculating
them in the driver. There may be some older r6xx
asics where this doesn't work correctly. This remains
to be seen.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE6/8.
v2: remove unused variables
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Do it before enabling audio channels (in AFMT_AUDIO_PACKET_CONTROL2
register).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to DCE4/5, but supports multiple audio pins
which can be assigned per afmt block.
v2: rework the driver to handle more than one audio
pin.
v3: try different dto reg
v4: properly program dto
v5 (ck): change dto programming order
v6: program speaker allocation block
v7: rebase
v8: rebase on Rafał's changes
v9: integrated Rafał's comments, update to latest
drm_edid_to_speaker_allocation API
v10: add missing line break in error message
v11: add back audio enabled messages
v12: fix copy paste typo in r600_audio_enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to set the dto source before setting the
dividers otherwise we may get stability problems
with the dto leading to audio playback problems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
- remove adding 2 to checksum, this is incorrect.
This was incorrectly introduced in:
92db7f6c86http://lists.freedesktop.org/archives/dri-devel/2011-December/017717.html
However, the off by 2 was due to adding the version twice.
From the examples in the URL above:
[Rafał Miłecki][RV620] fglrx:
0x7454: 00 A8 5E 79 R600_HDMI_VIDEOINFOFRAME_0
0x7458: 00 28 00 10 R600_HDMI_VIDEOINFOFRAME_1
0x745C: 00 48 00 28 R600_HDMI_VIDEOINFOFRAME_2
0x7460: 02 00 00 48 R600_HDMI_VIDEOINFOFRAME_3
===================
(0x82 + 0x2 + 0xD) + 0x1F8 = 0x289
-0x289 = 0x77
However, the payload sum is not 0x1f8, it's 0x1f6.
00 + A8 + 5E + 00 +
00 + 28 + 00 + 10 +
00 + 48 + 00 + 28 +
00 + 48 =
0x1f6
Bits 25:24 of HDMI_VIDEOINFOFRAME_3 are the packet version, not part
of the payload. So the total would be:
(0x82 + 0x2 + 0xD) + 0x1f6 = 0x287
-0x287 = 0x79
- properly emit the AVI infoframe version. This was not being
emitted previous which is probably what caused the issue above.
This should fix blank screen when HDMI audio is enabled on
certain monitors.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Cc: Rafał Miłecki <zajec5@gmail.com>
Avoids overflows on DCE2.x devices. Also clarify the calculation
on other asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This allows audio (alsa) driver to read them and have a clue about audio
capabilities of connected receiver. This has been verified to be
compatible with fglrx behaviour for Onkyo TX-SR605 and Denon 1912.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Register audio callbacks for asic where we support
audio. Cleans up the code and makes it easier to
add support for newer asics.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split into DCE2/3 and DCE4/5 variants. Still todo is to
calculate the DTO dividers properly. Add proper formula
to the comments.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver fglrx setups audio and ACR packets after basic initialization,
which sounds sane, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Closed source driver fglrx seems to enable infoframes and audio packets
at the end, which makes sense, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the generic HDMI infoframe helpers to get rid of the duplicate
implementation in the radeon driver.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher
Anssi Hannula
Dave Airlie
Rafał Miłecki
Thierry Reding
David Howells