Before sending a command to the ASIC, set version properly.
This is necessary for the ARM firmware to send correct data to the driver.
This also fixes a bug in certain skews of the ASIC where the statistics
are misreported.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pages are posted to the rxq in such a way that more than one frag
can share the page. The last frag that uses the page unmaps the
page. In the case when a page is not fully used (due to lack of space in rxq)
the last frag that uses the page is not being set as a "last_page_user";
instead, the next frag in the rxq is incorrectly being set.
The fix has also been tested on ppc64 with 64k pages...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to return correct values for transceiver and supported in
ethtool get_settings function.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change ensures that loopback test command gives up after 4 seconds when
the hardware is not responsive. This could happen if the ports are connected
properly in loopback mode.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are certain skews of the NIC which have multiple bits set in
adapter->cap. Use & instead of == to process rx completions.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool selftest.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a firmware command fails, only the failure codes are printed.
It is difficult to co-relate this to the actual command that has failed.
These changes will now print the command code that has failed.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every time while doing ethtool->get_settings we are accessing
the hardware to get link status and port information.
This is not necessary. We now use the cached copy for this info
and update it when the link status changes.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add be_rx_polls to count number of times NAPI called rx poll function.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port identification/beaconing is failing if device open has not been done.
Fixing it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow only valid ether addresses to be assigned and used for the interface.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
patch to initialize netdev->vlan_features appropriately.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can run out of mccq wrbs when completions don't arrive
due to an unresponsive card. This must not hit a BUG_ON(); instead
log a msg and return an error.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling msix was missing when probe fails after enabling msix.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These cmds are issued to the fw in probe/resume and remove/suspend
paths to help fw execute some initialization and cleanup code.
This change needed the be_hw_up() code to be refactored as be_get_config().
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To send upto 64 addresses in the multicast-set cmd, the non-embeeded cmd format
that provides for a bigger buffer is used instead of an embedded format.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please apply patch to update redboot section while firmware update. Code
checks if section needs to be updated before actually doing it.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending config commands to be2 hardware before netdev_register is
completed, is sometimes causing the async link notification to arrive
even before the driver is ready to handle it. The commands for vlan
config and flow control settings can infact wait till be_open.
This patch takes care of that.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If be2 goes into suspend after a user changes the flow control settings,
we are not programming them back after resume. This patch takes care of it.
We now get the flow control settings before going to suspend mode and
then apply them during resume.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PCI IDs for the next generation chip to the
PCI_DEVICE_ID table.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ethtool get_settings function to:
- get current link speed settings from controller
- get port transceiver type from controller
- fill appropriate values for supported, phy_address
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new PCI ids to support next generation of BladeEngine device.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before issuing any cmds to the FW, the driver must first wait
till the fW becomes ready. This is needed for PCI hot plug when
the driver can be probed while the card fw is being initialized.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter doesnot need to maintain a copy of net_device_stats.
Use the one already available in net_device. This patch takes care of the same.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for a bug which was a result of wrong use of checksum offload flag.
The status of tx-checksumming was not changed from on to off
after a 'ethtool -K <ifname> tx off' operation.
Use the proper checksum offload flag NETIF_F_HW_CSUM instead of
NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Patch is against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCC_STATUS_NOT_SUPPORTED should be decimal 66 not hex 66.
This patch fixes this typo. Patch against net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While updating the statistics to be passed via the get_stats,
tx multicast frames were being accounted instead of rx multicast frames.
This patch fixes the bug. This patch is against the net-2.6 tree.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that got introduced in commit 76998bc7.
During preparation of mcc wrb, req was being wrongly overwritten
and the flash operation was failing.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde
Sathya Perla
David S. Miller
Ajit Khaparde
Sarveshwar Bandi
Linus Torvalds
Jiri Kosina
André Goddard Rosa
Suresh R
Joe Perches
Alexander Duyck
Eric Dumazet