Commit Graph

47 Commits

Author SHA1 Message Date
Andrew Morton aa738adf89 natsemi: section fix
gcc-3.4.4 on powerpc:

drivers/net/natsemi.c:245: error: natsemi_pci_info causes a section type conflict

Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-09 23:41:08 -08:00
Mark Brown 6344f0521a natsemi: Update locking documentation
The documentation regarding synchronisation at the head of the natsemi
driver was badly bitrotted so replace it with a general statement about
the techniques used which is less likely to bitrot.

Also remove the note saying these chips are uncommon - it makes little
difference but they were used in a number of laptops and at least one mass
market PCI ethernet card.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-03 04:28:42 -08:00
David S. Miller 4ec2411980 [NET]: Do not check netif_running() and carrier state in ->poll()
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.

Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:09 -08:00
Ingo Molnar bbbab5ca83 natsemi: fix oops, link back netdevice from private-struct
* Andrew Nelless <andrew@nelless.net> wrote:

> Hi,
>
> I booted up 2.6.24-rc1 this morning [Real early over a brew ;-)] and
> was having a problems with multiple ~5 second hangs on SATA/drive init
> (Something to do with "EH" something-or-other and resets but I'll
> email in separately about it later unless its fixed by the time I get
> the chance).
>
> Anyway, I went to fire up netconsole to get a decent log dump and hit
> across the following nasty. Netconsole works fine in 2.6.23.1 with a
> similar config and the same kernel parameters.
>
> A shot of the screen is the only method I could come up with to
> capture the log, I hope that is OK, it is pretty readable.
>
>
> The nasty:
> http://andotnet.nfshost.com/linux/2.6.24-rc1-netconsole-nullderef.jpg

the NULL dereference is here:

 (gdb) list *0xffffffff804a9504
 0xffffffff804a9504 is in natsemi_poll (drivers/net/natsemi.c:717).
 712             return count;
 713     }
 714
 715     static inline void __iomem *ns_ioaddr(struct net_device *dev)
 716     {
 717             return (void __iomem *) dev->base_addr;
 718     }
 719

which is this code from natsemi.c:

 2227            struct net_device *dev = np->dev;
 2228            void __iomem * ioaddr = ns_ioaddr(dev);
 2229            int work_done = 0;

seems like the NAPI changes in -rc1 added an np->dev field but forgot to
initialize it ...

does the patch below fix the oops for you?

	Ingo

-------------------->
Subject: natsemi: fix oops, link back netdevice from private-struct
From: Ingo Molnar <mingo@elte.hu>

this commit:

  commit bea3348eef
  Author: Stephen Hemminger <shemminger@linux-foundation.org>
  Date:   Wed Oct 3 16:41:36 2007 -0700

      [NET]: Make NAPI polling independent of struct net_device objects.

added np->dev to drivers/net/natsemi.c's struct netdev_private, but
forgot to initialize that new field upon driver init. The result was
a predictable NULL dereference oops the first time the hardware
generated an interrupt.

Reported-by: Andrew Nelless <andrew@nelless.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-25 03:31:14 -04:00
Rolf Eike Beer 405bbe9fa3 Typo: depricated -> deprecated
Typo: depricated -> deprecated

Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-20 03:10:57 +02:00
Mark Brown a8a935dae5 natsemi: Check return value for pci_enable_device()
pci_enable_device() is __must_check so do that in natsemi_resume().

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 14:20:45 -04:00
Mark Brown 0e5d5442cb natsemi: Use round_jiffies() for slow timers
Unless we have failed to fill the RX ring the timer used by the natsemi
driver is not particularly urgent and can use round_jiffies() to allow
grouping with other timers.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 14:20:45 -04:00
Mark Brown f2cade1337 natsemi: Use NATSEMI_TIMER_FREQ consistently
The natsemi driver has a define NATSEMI_TIMER_FREQ which looks like it
controls the normal frequency of the chip poll timer but in fact only
takes effect for the first run of the timer.  Adjust the value of the
define to match that used by the timer and use the define consistently.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:55:29 -07:00
Stephen Hemminger ddfce6bb43 network drivers: sparse warning fixes
Fix some of the easy warnings in network device drivers.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:55:27 -07:00
Joe Perches 0795af5729 [NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()
This is nicer than the MAC_FMT stuff.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:42 -07:00
Ralf Baechle 10d024c1b2 [NET]: Nuke SET_MODULE_OWNER macro.
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it.  The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.

[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:51:13 -07:00
Stephen Hemminger bea3348eef [NET]: Make NAPI polling independent of struct net_device objects.
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.

In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.

The signature of the ->poll() call back goes from:

	int foo_poll(struct net_device *dev, int *budget)

to

	int foo_poll(struct napi_struct *napi, int budget)

The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract).  The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.

The napi_struct is to be embedded in the device driver private data
structures.

Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler.  Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.

With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.

Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.

[ Ported to current tree and all drivers converted.  Integrated
  Stephen's follow-on kerneldoc additions, and restored poll_list
  handling to the old style to fix mutual exclusion issues.  -DaveM ]

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-10-10 16:47:45 -07:00
Andrew Morton c76720cf7b natsemi: fix netdev error acounting
When a detailed netdev error is counted, we also must account for it in the
aggregated error count.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106

Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chongfeng Hu <loveminix@yahoo.com.cn>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-14 01:36:39 -04:00
Jeff Garzik f6c4286590 [netdrvr] natsemi: Fix device removal bug
This episode illustrates how an overused warning can train people to
ignore that warning, which winds up hiding bugs.

The warning

drivers/net/natsemi.c: In function ‘natsemi_remove1’:
drivers/net/natsemi.c:3222: warning: ignoring return value of
‘device_create_file’, declared with attribute warn_unused_result

is oft-ignored, even though at close inspection one notices this occurs
in the /remove/ function, not normally where creation occurs.  A quick
s/create/remove/ and we are fixed, with the warning gone.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-17 16:17:59 -04:00
David S. Miller 8c7b7faaa6 [NET]: Kill eth_copy_and_sum().
It hasn't "summed" anything in over 7 years, and it's
just a straight mempcy ala skb_copy_to_linear_data()
so just get rid of it.

Signed-off-by: David S. Miller <davem@davemloft.net>
2007-07-10 22:08:12 -07:00
Gregory Haskins d41f2d17f8 natsemi irq flags
The spinlock irq flags should be a unsigned long to properly support 64 bit

Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-20 19:15:04 -04:00
Markus Dahms 2c2a8c531e remove broken URLs from net drivers' output
Remove broken URLs (www.scyld.com) from network drivers' logging output.
URLs in comments and other strings are left intact.

Signed-off-by: Markus Dahms <dahms@fh-brandenburg.de>
Acked-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
igned-off-by: Adrian Bunk <bunk@stusta.de>
2007-05-09 08:58:18 +02:00
Mark Brown 1a14780960 Subject: natsemi: Allow users to disable workaround for DspCfg reset
The natsemi driver contains a workaround for broken hardware which can
partially reset the chip at unpredictable times, detected by checking for
spontaneous changes in the DspCfg register.  The effects of the hardware
bug appear to be variable and can range from minor problems like small
numbers of corrupted packets to major ones such as the chip becoming
non-functional.  In the case of minor problems the chip reconfiguration
required to work around the hardware can cause more problems than the bug
itself.

Since we have no way of automatically determining how badly the problem
manifests on any given system provide an option in sysfs allowing users to
disable the workaround at runtime and provides a module option to set the
default.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-08 01:15:35 -04:00
Mark Brown d0ed48640e natsemi: Improve diagnostics for DspCfg workaround
The natsemi driver has a workaround for broken hardware which resets itself
from time to time.  There is a diagnostic message for this workaround but
it is not printed by default, making the driver behavior more obscure than
it needs to be.  Make the message be displayed by default.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-08 01:15:35 -04:00
Arnaldo Carvalho de Melo 4c13eb6657 [ETH]: Make eth_type_trans set skb->dev like the other *_type_trans
One less thing for drivers writers to worry about.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2007-04-25 22:24:30 -07:00
broonie@sirena.org.uk d2a900365b natsemi: Avoid IntrStatus lossage if RX state machine resets.
This patch fixes the poll routine for the natsemi driver so that if the
driver detects an RX state machine lockup then no interrupts will be
lost while the driver recovers from that.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-15 10:59:54 -04:00
broonie@sirena.org.uk 069f825636 natsemi: Fix NAPI for interrupt sharing
The interrupt status register for the natsemi chips is clear on read and
was read unconditionally from both the interrupt and from the NAPI poll
routine, meaning that if the interrupt service routine was called (for
example, due to a shared interrupt) while a NAPI poll was scheduled
interrupts could be missed.  This patch fixes that by ensuring that the
interrupt status register is only read by the interrupt handler when
interrupts are enabled from the chip.

It also reverts a workaround for this problem from the netpoll hook and
improves the trace for interrupt events.

Thanks to Sergei Shtylyov <sshtylyov@ru.mvista.com> for spotting the
issue, Mark Huth <mhuth@mvista.com> for a simpler method and Simon
Blake <simon@citylink.co.nz> for testing resources.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-15 10:59:54 -04:00
broonie@sirena.org.uk 14fdd90ef2 natsemi: Consistently use interrupt enable/disable functions
The natsemi drivers include functions for enabling and disabling
interrupts from the chip but these are not used in all code paths.  This
patch changes the code paths that touch the interrupt enable register to
use the functions.  In all cases this adds an extra PCI read to post the
operation but since none of these are in fast paths this shouldn't be
too much of a problem.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-15 10:59:54 -04:00
Sergei Shtylyov 6006f7f517 natsemi: netpoll fixes
Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-06 06:10:01 -05:00
Mark Brown 36c843d5e3 natsemi: Fix detection of vanilla natsemi cards
Bob Tracy <rct@gherkin.frus.com> reported that the addition of support
for Aculab E1/T1 cPCI carrier cards broke detection of vanilla natsemi
cards.  This patch fixes that: the problem is that the driver-specific
ta in the PCI device table is an index into a second table and this
had not been updated for the vanilla cards.

This patch fixes the problem minimally.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27 04:30:43 -05:00
Mark Brown 6aab44475a natsemi: Support Aculab E1/T1 PMXc cPCI carrier cards
Aculab E1/T1 PMXc cPCI carrier card cards present a natsemi on the cPCI
bus with an oversized EEPROM using a direct MII<->MII connection with no
PHY.  This patch adds a new device table entry supporting these cards.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-20 11:18:13 -05:00
Mark Brown 68c90166e4 natsemi: Add support for using MII port with no PHY
This patch provides code paths which allow the natsemi driver to use the
external MII port on the chip but ignore any PHYs that may be attached to it.
The link state will be left as it was when the driver started and can be
configured via ethtool.  Any PHYs that are present can be accessed via the MII
ioctl()s.

This is useful for systems where the device is connected without a PHY
or where either information or actions outside the scope of the driver
are required in order to use the PHYs.

Signed-Off-By: Mark Brown <broonie@sirena.org.uk>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-20 11:18:13 -05:00
David Howells 7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
Jeff Garzik 7282d491ec drivers/net: const-ify ethtool_ops declarations
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13 14:30:00 -04:00
Jeff Garzik 6aa20a2235 drivers/net: Trim trailing whitespace
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-13 13:24:59 -04:00
Jeff Garzik 4e83b7fad8 Merge branch 'tmp' into upstream 2006-09-12 11:45:33 -04:00
Andy Gospodarek d5b20697ca [PATCH] Remove more unnecessary driver printk's
As I promised last week, here is the first pass at removing all
unnecessary printk's that exist in network device drivers currently in
promiscuous mode.  The duplicate messages are not needed so they have
been removed.  Some of these drivers are quite old and might not need an
update, but I did them all anyway.

I am currently auditing the remaining conditional printk's and will send
out a patch for those soon.

Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-09-12 11:45:19 -04:00
Jeff Garzik 299176206b drivers/net: Remove deprecated use of pci_module_init()
From: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>

Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-08-19 17:48:59 -04:00
Jeff Garzik 03a8c6611a [netdrvr] Remove Linux-specific changelogs from several Becker template drivers
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code.  These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.

Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9".  These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.

Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-07-05 13:40:49 -04:00
Thomas Gleixner 1fb9df5d30 [PATCH] irq-flags: drivers/net: Use the new IRQF_ constants
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-02 13:58:51 -07:00
Jörn Engel 6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Jeff Garzik a2b524b2ec [netdrvr] natsemi: minor cleanups
* make eeprom size a variable, prepping for future patch
* eliminate unused PCI_xxx stuff left over from Becker driver template
* convert a few #defines to enum
* mark PCI table const, __devinitdata
* don't bother with named constant for PCI device id

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26 22:48:38 -04:00
Jeff Garzik 5a40f09baa [netdrvr] natsemi: Separate out media initialization code
This makes it easier to merge an upcoming patch, and overall makes the
code a bit more clean.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-06-26 22:24:03 -04:00
Herbert Xu 932ff279a4 [NET]: Add netif_tx_lock
Various drivers use xmit_lock internally to synchronise with their
transmission routines.  They do so without setting xmit_lock_owner.
This is fine as long as netpoll is not in use.

With netpoll it is possible for deadlocks to occur if xmit_lock_owner
isn't set.  This is because if a printk occurs while xmit_lock is held
and xmit_lock_owner is not set can cause netpoll to attempt to take
xmit_lock recursively.

While it is possible to resolve this by getting netpoll to use
trylock, it is suboptimal because netpoll's sole objective is to
maximise the chance of getting the printk out on the wire.  So
delaying or dropping the message is to be avoided as much as possible.

So the only alternative is to always set xmit_lock_owner.  The
following patch does this by introducing the netif_tx_lock family of
functions that take care of setting/unsetting xmit_lock_owner.

I renamed xmit_lock to _xmit_lock to indicate that it should not be
used directly.  I didn't provide irq versions of the netif_tx_lock
functions since xmit_lock is meant to be a BH-disabling lock.

This is pretty much a straight text substitution except for a small
bug fix in winbond.  It currently uses
netif_stop_queue/spin_unlock_wait to stop transmission.  This is
unsafe as an IRQ can potentially wake up the queue.  So it is safer to
use netif_tx_disable.

The hamradio bits used spin_lock_irq but it is unnecessary as
xmit_lock must never be taken in an IRQ handler.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2006-06-17 21:30:14 -07:00
Randy Dunlap e19360f294 [PATCH] net drivers: fix section attributes for gcc
If CONFIG_HOTPLUG=n, gcc doesn't like some __initdata to be const (rodata)
and other __initdata not const, so make the non-const __initdata const.

gcc errors:
drivers/net/bnx2.c:66: error: version causes a section type conflict
drivers/net/starfire.c:338: error: version causes a section type conflict
drivers/net/typhoon.c:137: error: version causes a section type conflict
drivers/net/natsemi.c:241: error: version causes a section type conflict

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-04-12 18:08:45 -04:00
Mark Brown a8b4cf42cf [PATCH] natsemi: Support oversized EEPROMs
The natsemi chip can have a larger EEPROM attached than it itself uses for
configuration.  This patch adds support for user space access to such an
EEPROM.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-29 17:34:02 -05:00
Mark Brown e72fd96e8e [PATCH] natsemi: NAPI and a bugfix
As documented in National application note 1287 the RX state machine on
the natsemi chip can lock up under some conditions (mostly related to
heavy load).  When this happens a series of bogus packets are reported
by the chip including some oversized frames prior to the final lockup.

This patch implements the fix from the application note: when an
oversized packet is reported it resets the RX state machine, dropping
any currently pending packets.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-04 12:14:56 -05:00
Mark Brown b27a16b7c4 [PATCH] natsemi: NAPI and a bugfix
This patch converts the natsemi driver to use NAPI.  It was originally
based on one written by Harald Welte, though it has since been modified
quite a bit, most extensively in order to remove the ability to disable
NAPI since none of the other drivers seem to provide that functionality
any more.

Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-03-04 12:14:56 -05:00
Arjan van de Ven f71e130966 Massive net driver const-ification. 2006-03-03 21:33:57 -05:00
David S. Miller 689be43945 [NET]: Remove gratuitous use of skb->tail in network drivers.
Many drivers use skb->tail unnecessarily.

In these situations, the code roughly looks like:

	dev = dev_alloc_skb(...);

	[optional] skb_reserve(skb, ...);

	... skb->tail ...

But even if the skb_reserve() happens, skb->data equals
skb->tail.  So it doesn't make any sense to use anything
other than skb->data in these cases.

Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers.  It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.

Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge.  In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
2005-06-28 15:25:31 -07:00
Herbert Xu 760f86d78d [PATCH] Fw: [Bugme-new] [Bug 4482] New: natsemi: incorrect initialization of IPv6 Neighbor-discovery multicast
On Wed, Apr 13, 2005 at 05:36:42PM +0000, Andrew Morton wrote:
>            Summary: natsemi: incorrect initialization of IPv6 Neighbor-
>                     discovery multicast

I've got a pair of FA312 cards and this problem has bothered me
for ages.  This has finally prompted me to do something about it :)

Turns out that somebody wasn't following the documentation.  We were
doing 16-bit writes to 32-bit registers which led to some addresses
working and others not so lucky.

This patch should fix the problem.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2005-05-15 18:18:56 -04:00
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00