Commit Graph

450 Commits

Author SHA1 Message Date
Emilio López 2bf420a768 net: sun4i: fix timeout check
The current timeout check is comparing two constant values, so it won't
ever detect a timeout. This patch reworks the affected code a bit so it
has a chance at detecting timeouts correctly.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-24 17:04:20 -07:00
Linus Torvalds be9c6d9169 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
 "Just a bunch of small fixes and tidy ups:

   1) Finish the "busy_poll" renames, from Eliezer Tamir.

   2) Fix RCU stalls in IFB driver, from Ding Tianhong.

   3) Linearize buffers properly in tun/macvtap zerocopy code.

   4) Don't crash on rmmod in vxlan, from Pravin B Shelar.

   5) Spinlock used before init in alx driver, from Maarten Lankhorst.

   6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
      Kravkov.

   7) Dummy and ifb driver load failure paths can oops, fixes from Tan
      Xiaojun and Ding Tianhong.

   8) Correct MTU calculations in IP tunnels, from Alexander Duyck.

   9) Account all TCP retransmits in SNMP stats properly, from Yuchung
      Cheng.

  10) atl1e and via-rhine do not handle DMA mapping failures properly,
      from Neil Horman.

  11) Various equal-cost multipath route fixes in ipv6 from Hannes
      Frederic Sowa"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
  ipv6: only static routes qualify for equal cost multipathing
  via-rhine: fix dma mapping errors
  atl1e: fix dma mapping warnings
  tcp: account all retransmit failures
  usb/net/r815x: fix cast to restricted __le32
  usb/net/r8152: fix integer overflow in expression
  net: access page->private by using page_private
  net: strict_strtoul is obsolete, use kstrtoul instead
  drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
  drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
  drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
  net/usb: add relative mii functions for r815x
  net/tipc: use %*phC to dump small buffers in hex form
  qlcnic: Adding Maintainers.
  gre: Fix MTU sizing check for gretap tunnels
  pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
  pkt_sched: sch_qfq: improve efficiency of make_eligible
  gso: Update tunnel segmentation to support Tx checksum offload
  inet: fix spacing in assignment
  ifb: fix oops when loading the ifb failed
  ...
2013-07-13 17:42:22 -07:00
Linus Torvalds d144746478 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
 "MIPS updates:

   - All the things that didn't make 3.10.
   - Removes the Windriver PPMC platform.  Nobody will miss it.
   - Remove a workaround from kernel/irq/irqdomain.c which was there
     exclusivly for MIPS.  Patch by Grant Likely.
   - More small improvments for the SEAD 3 platform
   - Improvments on the BMIPS / SMP support for the BCM63xx series.
   - Various cleanups of dead leftovers.
   - Platform support for the Cavium Octeon-based EdgeRouter Lite.

  Two large KVM patchsets didn't make it for this pull request because
  their respective authors are vacationing"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
  MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
  MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
  MIPS: SEAD3: Disable L2 cache on SEAD-3.
  MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
  MIPS: BCM63xx: Add SMP support to prom.c
  MIPS: define write{b,w,l,q}_relaxed
  MIPS: Expose missing pci_io{map,unmap} declarations
  MIPS: Malta: Update GCMP detection.
  Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
  MIPS: APSP: Remove <asm/kspd.h>
  SSB: Kconfig: Amend SSB_EMBEDDED dependencies
  MIPS: microMIPS: Fix improper definition of ISA exception bit.
  MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
  MIPS: Declare emulate_load_store_microMIPS as a static function.
  MIPS: Fix typos and cleanup comment
  MIPS: Cleanup indentation and whitespace
  MIPS: BMIPS: support booting from physical CPU other than 0
  MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
  MIPS: GIC: Fix gic_set_affinity infinite loop
  MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
  ...
2013-07-13 14:52:21 -07:00
Helmut Schaa ce9a1bf8e6 drivers: net: phy: at803x: Add missing mdio device id
at803x supports Atheros 8030, 8031 and 8035 PHYs. 8031 was missing from
the mdio device id table.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-11 11:54:19 -07:00
Linus Torvalds 496322bc91 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "This is a re-do of the net-next pull request for the current merge
  window.  The only difference from the one I made the other day is that
  this has Eliezer's interface renames and the timeout handling changes
  made based upon your feedback, as well as a few bug fixes that have
  trickeled in.

  Highlights:

   1) Low latency device polling, eliminating the cost of interrupt
      handling and context switches.  Allows direct polling of a network
      device from socket operations, such as recvmsg() and poll().

      Currently ixgbe, mlx4, and bnx2x support this feature.

      Full high level description, performance numbers, and design in
      commit 0a4db187a9 ("Merge branch 'll_poll'")

      From Eliezer Tamir.

   2) With the routing cache removed, ip_check_mc_rcu() gets exercised
      more than ever before in the case where we have lots of multicast
      addresses.  Use a hash table instead of a simple linked list, from
      Eric Dumazet.

   3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
      Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
      Marek Puzyniak, Michal Kazior, and Sujith Manoharan.

   4) Support reporting the TUN device persist flag to userspace, from
      Pavel Emelyanov.

   5) Allow controlling network device VF link state using netlink, from
      Rony Efraim.

   6) Support GRE tunneling in openvswitch, from Pravin B Shelar.

   7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
      Daniel Borkmann and Eric Dumazet.

   8) Allow controlling of TCP quickack behavior on a per-route basis,
      from Cong Wang.

   9) Several bug fixes and improvements to vxlan from Stephen
      Hemminger, Pravin B Shelar, and Mike Rapoport.  In particular,
      support receiving on multiple UDP ports.

  10) Major cleanups, particular in the area of debugging and cookie
      lifetime handline, to the SCTP protocol code.  From Daniel
      Borkmann.

  11) Allow packets to cross network namespaces when traversing tunnel
      devices.  From Nicolas Dichtel.

  12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
      manner akin to how we monitor real network traffic via ptype_all.
      From Daniel Borkmann.

  13) Several bug fixes and improvements for the new alx device driver,
      from Johannes Berg.

  14) Fix scalability issues in the netem packet scheduler's time queue,
      by using an rbtree.  From Eric Dumazet.

  15) Several bug fixes in TCP loss recovery handling, from Yuchung
      Cheng.

  16) Add support for GSO segmentation of MPLS packets, from Simon
      Horman.

  17) Make network notifiers have a real data type for the opaque
      pointer that's passed into them.  Use this to properly handle
      network device flag changes in arp_netdev_event().  From Jiri
      Pirko and Timo Teräs.

  18) Convert several drivers over to module_pci_driver(), from Peter
      Huewe.

  19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
      O(1) calculation instead.  From Eric Dumazet.

  20) Support setting of explicit tunnel peer addresses in ipv6, just
      like ipv4.  From Nicolas Dichtel.

  21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.

  22) Prevent a single high rate flow from overruning an individual cpu
      during RX packet processing via selective flow shedding.  From
      Willem de Bruijn.

  23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
      Dumazet.

  24) Don't just drop GSO packets which are above the TBF scheduler's
      burst limit, chop them up so they are in-bounds instead.  Also
      from Eric Dumazet.

  25) VLAN offloads are missed when configured on top of a bridge, fix
      from Vlad Yasevich.

  26) Support IPV6 in ping sockets.  From Lorenzo Colitti.

  27) Receive flow steering targets should be updated at poll() time
      too, from David Majnemer.

  28) Fix several corner case regressions in PMTU/redirect handling due
      to the routing cache removal, from Timo Teräs.

  29) We have to be mindful of ipv4 mapped ipv6 sockets in
      upd_v6_push_pending_frames().  From Hannes Frederic Sowa.

  30) Fix L2TP sequence number handling bugs, from James Chapman."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
  drivers/net: caif: fix wrong rtnl_is_locked() usage
  drivers/net: enic: release rtnl_lock on error-path
  vhost-net: fix use-after-free in vhost_net_flush
  net: mv643xx_eth: do not use port number as platform device id
  net: sctp: confirm route during forward progress
  virtio_net: fix race in RX VQ processing
  virtio: support unlocked queue poll
  net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
  Documentation: Fix references to defunct linux-net@vger.kernel.org
  net/fs: change busy poll time accounting
  net: rename low latency sockets functions to busy poll
  bridge: fix some kernel warning in multicast timer
  sfc: Fix memory leak when discarding scattered packets
  sit: fix tunnel update via netlink
  dt:net:stmmac: Add dt specific phy reset callback support.
  dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
  dt:net:stmmac: Allocate platform data only if its NULL.
  net:stmmac: fix memleak in the open method
  ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
  net: ipv6: fix wrong ping_v6_sendmsg return value
  ...
2013-07-09 18:24:39 -07:00
Linus Torvalds f317ff9eed Merge branch 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
 "Surprisingly, Lai and I didn't break too many things implementing
  custom pools and stuff last time around and there aren't any follow-up
  changes necessary at this point.

  The only change in this pull request is Viresh's patches to make some
  per-cpu workqueues to behave as unbound workqueues dependent on a boot
  param whose default can be configured via a config option.  This leads
  to higher processing overhead / lower bandwidth as more work items are
  bounced across CPUs; however, it can lead to noticeable powersave in
  certain configurations - ~10% w/ idlish constant workload on a
  big.LITTLE configuration according to Viresh.

  This is because per-cpu workqueues interfere with how the scheduler
  perceives whether or not each CPU is idle by forcing pinned tasks on
  them, which makes the scheduler's power-aware scheduling decisions
  less effective.

  Its effectiveness is likely less pronounced on homogenous
  configurations and this type of optimization can probably be made
  automatic; however, the changes are pretty minimal and the affected
  workqueues are clearly marked, so it's an easy gain for some
  configurations for the time being with pretty unintrusive changes."

* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  fbcon: queue work on power efficient wq
  block: queue work on power efficient wq
  PHYLIB: queue work on system_power_efficient_wq
  workqueue: Add system wide power_efficient workqueues
  workqueues: Introduce new flag WQ_POWER_EFFICIENT for power oriented workqueues
2013-07-02 19:53:30 -07:00
David Daney 9ddebc46e7 MIPS: OCTEON: Rename Kconfig CAVIUM_OCTEON_REFERENCE_BOARD to CAVIUM_OCTEON_SOC
CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON.  This
allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC.

Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can
get the same configuration with CAVIUM_OCTEON_SOC.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
Cc: devel@driverdev.osuosl.org
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/5295/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2013-06-10 18:01:25 +02:00
David S. Miller 6bc19fb82d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.

This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge.  Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-05 16:37:30 -07:00
Mugunthan V N 05d7cce8fe drivers: net: phy: at803x: add support for AT8031
This patch adds support for Atheros 8031 phy driver.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04 14:17:22 -07:00
Mugunthan V N 1ca6d1b1ae drivers: net: phy: at803x: add interface mode support
This patch adds support for RGMII TX delay configuration on Atheros 803X,
this can be enabled in debug registers. With this patch,
PHY_INTERFACE_MODE_RGMII_TXID modes are now supported.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04 14:17:21 -07:00
Mugunthan V N ea13c9ee85 drivers: net: phy: at803x: seperate wol specific code to wol standard apis
WOL is initilized in phy config_init, but there are standard apis
(set_wol/get_wol) for WOL in phy frame work. So this patch moves
WOL specific code from config_init to wol standard apis.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04 14:17:21 -07:00
Mugunthan V N 317420ab23 drivers: net: phy: at803x code cleanup on register and unregister driver
Make use of phy_drivers_register/phy_drivers_unregister to register/unregister
multiple phy drivers in a single module.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04 14:17:21 -07:00
Maxime Ripard 4bdcb1dd9f net: Add MDIO bus driver for the Allwinner EMAC
This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 17:23:07 -07:00
Michal Simek 10e24caa98 phy: Add Marvell 88E1510 phy ID
Add support for this new phy ID.

Signed-off-by: Rick Hoover <RHoover@digilentinc.com>
Signed-off-by: Steven Wang <steven.wang@digilentinc.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 00:48:22 -07:00
Michal Simek 3da09a5154 phy: Add Marvell 88E1116R phy ID
This phy is on Xilinx ZC702 zynq development board.

Signed-off-by: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 00:48:22 -07:00
Michal Simek f5e1cabf46 phy: Use macros instead of hardcoded values in marvell phy driver
Use macros from linux/marvell_phy.h instead of duplicate
magic phy ID in the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 00:48:22 -07:00
Michal Simek 5a1cebd8f4 phy: Add Vitesse 8211 phy ID
Phy is compatible with Vitesse 8221.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 00:48:22 -07:00
Michal Simek 2a8626d1ef phy: Clean coding style in vitesse phy
- Remove trailing white space
- Remove spaces before tag
- Fix comments

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-31 00:48:22 -07:00
Giuseppe CAVALLARO 9a9c56cb34 net: phy: fix a bug when verify the EEE support
The phy_init_eee has to exit with an error when the
local device and its link partner both do not support EEE.
So this patch fixes a problem when verify this.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27 23:30:09 -07:00
Sachin Kamat 1a9561a3bd net/phy: Use module_spi_driver in spi_ks8995.c
module_spi_driver() removes some boilerplate and makes the code
simpler.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27 23:24:29 -07:00
Florian Fainelli 50ab731e96 phy: bcm63xx: report Broadcom BCM63xx PHYs as internal
The Broadcom BCM63xx PHY driver is for the SoC internal PHYs, flag these
as internal PHY devices.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27 22:42:50 -07:00
Florian Fainelli 4284b6a535 phy: allow drivers to flag a PHY device as internal
libphy currently always reports a PHY as an external transceiver from
the ethtool output. This is inaccurate, because some drivers should be
able to tell that a PHY device is an internal transceiver of an Ethernet
MAC. Add a new flag (PHY_IS_INTERNAL) which can be set by PHY drivers
just like other flags, and a corresponding helper: phy_is_internal()
which can be used by networking drivers to query if a given
PHY device is internal.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-27 22:42:50 -07:00
Florian Fainelli 5ea94e7686 phy: add phy_mac_interrupt() to use with PHY_IGNORE_INTERRUPT
There is currently no way for an Ethernet MAC driver servicing PHY link
interrupts to notify this to the PHY state machine without defining its
own state machine. Since most drivers are not so special, introduce a
helper: phy_mac_interrupt() which can be called from a link up/down
interrupt routine to update the PHY state machine. To avoid code
duplication some refactoring has been done to expose the workqueue and
its corresponding callback internally.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-20 14:13:08 -07:00
Florian Fainelli 2c7b49212a phy: fix the use of PHY_IGNORE_INTERRUPT
When a PHY device is registered with the special IRQ value
PHY_IGNORE_INTERRUPT (-2) it will not properly be handled by the PHY
library:

- it continues to poll its register, while we do not want this
  because such PHY link events or register changes are serviced by an
  Ethernet MAC
- it will still try to configure PHY interrupts at the PHY level, such
  interrupts do not exist at the PHY but at the MAC level
- the state machine only handles PHY_POLL, but should also handle
  PHY_IGNORE_INTERRUPT similarly

This patch updates the PHY state machine and initialization paths to
account for the specific PHY_IGNORE_INTERRUPT. Based on an earlier patch
by Thomas Petazzoni, and reworked to add the missing bits. Add a helper
phy_interrupt_is_valid() which specifically tests for a PHY interrupt
not to be PHY_POLL or PHY_IGNORE_INTERRUPT and use it throughout the
code.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-05-20 14:13:08 -07:00
Viresh Kumar bbb47bdeae PHYLIB: queue work on system_power_efficient_wq
Phylib uses workqueues for multiple purposes. There is no real dependency of
scheduling these on the cpu which scheduled them.

On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.

This patch replaces system_wq with system_power_efficient_wq for PHYLIB.

Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
2013-05-14 10:50:06 -07:00
Linus Torvalds 5647ac0ad4 Removal of GENERIC_GPIO for v3.10
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
 cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
 possible to do so which has been causing confusion and breakage. This
 branch does the work to completely eliminate GENERIC_GPIO.
 
 However, it is not trivial to just create a branch to remove it. Over
 the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
 added to linux-next that conflicts with this branch. The following must
 be done to resolve the conflicts when merging this branch into mainline:
 
 * "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
   replaced with CONFIG_GPIOLIB
 * "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
   documentation.
 * Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
 * definitions of the option in architecture Kconfig code should be deleted.
 
 Stephen has 3 merge fixup patches[1] that do the above. They are currently
 applicable on mainline as of May 2nd.
 
 [1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJRifUnAAoJEEFnBt12D9kBs2YP/0U6+ia+xYvkVaJc28PDVIzn
 OReZNcJOYU8D5voxz0voaRD0EdcPwjbMu9Kp9aXMHlk4VxevF+8jCc/us0bIjtO1
 VcB5VmSCIhMhxdnBlum11Mk7Vr5MCweyl9NBsypnPt8cl4obMBZHf2yzoodFktNb
 wtyYlOb6FALtc6iDbOO6dG3w9F7FAOLvskUFzdv89m8mupTsBu9jw9NqFDbJHOex
 rxq0Sdd+kWF/nkJVcV5Y6jIdletRlhpipefMJ9diexreHvwqh+c4kJEYZaXgB5+m
 ha95cPbReK1d+RqzM3A8d4irzSVSmq4k7ijI6QkFOr48+AH7XsgKv5so885LKzMN
 IIXg2Phm9i0H8+ecEvhcc4oIYBHJiEKK54Y0qUD9dqbFoDGPTCSqMHdSSMbpAY+J
 bIIXlVzj1En3PPNUJLPt8q8Qz6WxCT9mDST3QSGYnD4o90HT+1R9j92RxGL6McOq
 rUOyJDwmzFvpBvKK4raGdOU435M+ps2NPKKNIRaIGQPPY9rM1kN4YqvhXukEsC9L
 3a3+3cQLh7iKxBHncxeQsJfethP1CPkJnzvF9r+ZZLf2rcPH4pbQIE2uO0XnX/nd
 5/DKi0nGgAJ//GMMzdo3RiOA5zGFjIZ/KMvfhQldpP6qFJRhqdGi6FPlAcwr1z1n
 YnCByPwwlvfC4LTXFOGL
 =xodc
 -----END PGP SIGNATURE-----

Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux

Pull removal of GENERIC_GPIO from Grant Likely:
 "GENERIC_GPIO now synonymous with GPIOLIB.  There are no longer any
  valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
  is possible to do so which has been causing confusion and breakage.
  This branch does the work to completely eliminate GENERIC_GPIO."

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
  gpio: update gpio Chinese documentation
  Remove GENERIC_GPIO config option
  Convert selectors of GENERIC_GPIO to GPIOLIB
  blackfin: force use of gpiolib
  m68k: coldfire: use gpiolib
  mips: pnx833x: remove requirement for GENERIC_GPIO
  openrisc: default GENERIC_GPIO to false
  avr32: default GENERIC_GPIO to false
  xtensa: remove explicit selection of GENERIC_GPIO
  sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
  powerpc: remove redundant GENERIC_GPIO selection
  unicore32: default GENERIC_GPIO to false
  unicore32: remove unneeded select GENERIC_GPIO
  arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
  arm: remove redundant GENERIC_GPIO selection
  mips: alchemy: require gpiolib
  mips: txx9: change GENERIC_GPIO to GPIOLIB
  mips: loongson: use GPIO driver on CONFIG_GPIOLIB
  mips: remove redundant GENERIC_GPIO select
2013-05-09 09:59:16 -07:00
Alexandre Courbot 76ec9d18b8 Convert selectors of GENERIC_GPIO to GPIOLIB
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.

Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
2013-04-16 18:47:14 +09:00
David Daney 775ae9b264 netdev/phy: Implement ieee802.3 clause 45 in mdio-octeon.c
The Octeon SMI/MDIO interfaces can do clause 45 communications, so
implement this in the driver.

Also fix some comment formatting to make it consistent and to comply
with the netdev style.

Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07 17:12:01 -04:00
Jingoo Han 5d5f18460f net: phy: spi_ks8995: use spi_get_drvdata() and spi_set_drvdata()
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-07 16:48:19 -04:00
Kirill Kapranov a33e6112d9 phy: Elimination the forced speed reduction algorithm.
In case of fixed speed set up for a NIC (e.g. ethtool -s eth0 autoneg off speed
100 duplex full) with an ethernet cable plugged off, the mentioned algorithm
slows down a NIC speed, so further cable hook-up leads to nonoperable link state.

Signed-off-by: Kirill Kapranov <kapranoff@inbox.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-27 13:10:43 -04:00
Sachin Kamat 9fad0c941a net: mdio-octeon: Use module_platform_driver()
module_platform_driver macro removes some boilerplate and
simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-20 13:25:37 -04:00
Sachin Kamat f8e5fc8c20 net: mdio-gpio: Use module_platform_driver()
module_platform_driver macro removes some boilerplate and
simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-20 13:25:37 -04:00
Michael Stapelberg 3871c3876f mv643xx_eth with 88E1318S: support Wake on LAN
This has been tested on a qnap TS-119P II. Note that enabling WOL with
"ethtool -s eth0 wol g" is not enough; you also need to tell the PIC
microcontroller inside the qnap that WOL should be enabled by sending
0xF2 with qcontrol(1) and you have to disable EUP ("Energy-using
Products", a European power-saving thing) by sending 0xF4.

Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-12 11:40:54 -04:00
Michael Stapelberg 42e836eb45 phy: add set_wol/get_wol functions
This allows ethernet drivers (such as the mv643xx_eth) to support
Wake on LAN on platforms where PHY registers have to be configured
for Wake on LAN (e.g. the Marvell Kirkwood based qnap TS-119P II).

Signed-off-by: Michael Stapelberg <michael@stapelberg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-12 11:40:53 -04:00
Hector Palacios b6bb4dfcb1 phy/micrel: move flag handling to function for common use
The flag MICREL_PHY_50MHZ_CLK is not of exclusive use of KSZ8051
model. At least KSZ8021 and KSZ8031 models also use it.
This patch moves the handling of this and future flags to a
separate function so that the different PHY models can call it on
their init function, if needed.

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-12 06:50:59 -04:00
Hector Palacios b818d1a7f7 phy/micrel: Add support for KSZ8031
Micrel PHY KSZ8031 is similar to KSZ8021 and also requires the special
initialization of "Operation Mode Strap Override" in reg 0x16
introduced in 212ea99 (phy/micrel: Implement support for KSZ8021).

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-12 06:50:58 -04:00
stephen hemminger baec126cf6 phy: vitesse make vsc824x_add_skew static
Function is only used in this file, should be static and not
an exported symbol.

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-09 16:09:17 -05:00
stephen hemminger 199453339d Supject: phy: make local function static
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-09 16:09:17 -05:00
Vlastimil Kosar 32fcafbcd1 net/phy: micrel: Disable asymmetric pause for KSZ9021
Phyter KSZ9021 has hardware bug. If asymmetric pause is enabled,
then it is necessary to disconnect and then reconnect the ethernet
cable to get the phyter working. The solution is to disable the
asymmetric pause.

Signed-off-by: Vlastimil Kosar <ikosar@fit.vutbr.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-28 15:37:30 -05:00
Petr Malat b2a431915d phy: Fix phy_device_free memory leak
Fix memory leak in phy_device_free() for the case when phy_device*
returned by phy_device_create() is not registered in the system.

Bug description:
phy_device_create() sets name of kobject using dev_set_name(), which
allocates memory using kvasprintf(), but this memory isn't freed if
the underlying device isn't registered properly, because kobject_cleanup()
is not called in that case. This can happen (and actually is happening on
our machines) if phy_device_register(), called by mdiobus_scan(), fails.

Patch description:
Embedded struct device is initialized in phy_device_create() and it
counterpart phy_device_free() just drops one reference to the device,
which leads to proper deinitialization including releasing the kobject
name memory.

Signed-off-by: Petr Malat <oss@malat.biz>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-28 15:37:30 -05:00
Linus Torvalds 81ec44a6c6 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 update from Martin Schwidefsky:
 "The most prominent change in this patch set is the software dirty bit
  patch for s390.  It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
  the page_test_and_clear_dirty primitive which makes the common memory
  management code a bit less obscure.

  Heiko fixed most of the PCI related fallout, more often than not
  missing GENERIC_HARDIRQS dependencies.  Notable is one of the 3270
  patches which adds an export to tty_io to be able to resize a tty.

  The rest is the usual bunch of cleanups and bug fixes."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
  s390/module: Add missing R_390_NONE relocation type
  drivers/gpio: add missing GENERIC_HARDIRQ dependency
  drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
  s390/cleanup: rename SPP to LPP
  s390/mm: implement software dirty bits
  s390/mm: Fix crst upgrade of mmap with MAP_FIXED
  s390/linker skript: discard exit.data at runtime
  drivers/media: add missing GENERIC_HARDIRQS dependency
  s390/bpf,jit: add vlan tag support
  drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
  iucv: fix kernel panic at reboot
  s390/Kconfig: sort list of arch selected config options
  phylib: remove !S390 dependeny from Kconfig
  uio: remove !S390 dependency from Kconfig
  dasd: fix sysfs cleanup in dasd_generic_remove
  s390/pci: fix hotplug module init
  s390/pci: cleanup clp page allocation
  s390/pci: cleanup clp inline assembly
  s390/perf: cpum_cf: fallback to software sampling events
  s390/mm: provide PAGE_SHARED define
  ...
2013-02-21 17:54:03 -08:00
Linus Torvalds 06991c28f3 Driver core patches for 3.9-rc1
Here is the big driver core merge for 3.9-rc1
 
 There are two major series here, both of which touch lots of drivers all
 over the kernel, and will cause you some merge conflicts:
   - add a new function called devm_ioremap_resource() to properly be
     able to check return values.
   - remove CONFIG_EXPERIMENTAL
 
 If you need me to provide a merged tree to handle these resolutions,
 please let me know.
 
 Other than those patches, there's not much here, some minor fixes and
 updates.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
 weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
 =yWAQ
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core patches from Greg Kroah-Hartman:
 "Here is the big driver core merge for 3.9-rc1

  There are two major series here, both of which touch lots of drivers
  all over the kernel, and will cause you some merge conflicts:

   - add a new function called devm_ioremap_resource() to properly be
     able to check return values.

   - remove CONFIG_EXPERIMENTAL

  Other than those patches, there's not much here, some minor fixes and
  updates"

Fix up trivial conflicts

* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
  base: memory: fix soft/hard_offline_page permissions
  drivercore: Fix ordering between deferred_probe and exiting initcalls
  backlight: fix class_find_device() arguments
  TTY: mark tty_get_device call with the proper const values
  driver-core: constify data for class_find_device()
  firmware: Ignore abort check when no user-helper is used
  firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
  firmware: Make user-mode helper optional
  firmware: Refactoring for splitting user-mode helper code
  Driver core: treat unregistered bus_types as having no devices
  watchdog: Convert to devm_ioremap_resource()
  thermal: Convert to devm_ioremap_resource()
  spi: Convert to devm_ioremap_resource()
  power: Convert to devm_ioremap_resource()
  mtd: Convert to devm_ioremap_resource()
  mmc: Convert to devm_ioremap_resource()
  mfd: Convert to devm_ioremap_resource()
  media: Convert to devm_ioremap_resource()
  iommu: Convert to devm_ioremap_resource()
  drm: Convert to devm_ioremap_resource()
  ...
2013-02-21 12:05:51 -08:00
Linus Torvalds a0b1c42951 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking update from David Miller:

 1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
    timestamp offset.  From Andrey Vagin.

 2) VMWARE VM VSOCK layer, from Andy King.

 3) Much improved support for virtual functions and SR-IOV in bnx2x,
    from Ariel ELior.

 4) All protocols on ipv4 and ipv6 are now network namespace aware, and
    all the compatability checks for initial-namespace-only protocols is
    removed.  Thanks to Tom Parkin for helping deal with the last major
    holdout, L2TP.

 5) IPV6 support in netpoll and network namespace support in pktgen,
    from Cong Wang.

 6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
    Protocol (MVRP) support, from David Ward.

 7) Compute packet lengths more accurately in the packet scheduler, from
    Eric Dumazet.

 8) Use per-task page fragment allocator in skb_append_datato_frags(),
    also from Eric Dumazet.

 9) Add support for connection tracking labels in netfilter, from
    Florian Westphal.

10) Fix default multicast group joining on ipv6, and add anti-spoofing
    checks to 6to4 and 6rd.  From Hannes Frederic Sowa.

11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
    times, rearrange inet frag datastructures for better cacheline
    locality, and move more operations outside of locking.  From Jesper
    Dangaard Brouer.

12) Instead of strict master <--> slave relationships, allow arbitrary
    scenerios with "upper device lists".  From Jiri Pirko.

13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
    Pirko.

14) Add a BPF filter netfilter match target, from Willem de Bruijn.

15) Orphan and delete a bunch of pre-historic networking drivers from
    Paul Gortmaker.

16) Add TSO support for GRE tunnels, from Pravin B SHelar.  Although
    this still needs some minor bug fixing before it's %100 correct in
    all cases.

17) Handle unresolved IPSEC states like ARP, with a resolution packet
    queue.  From Steffen Klassert.

18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
    Hemminger.  This was long overdue.

19) Support SO_REUSEPORT, from Tom Herbert.

20) Allow locking a socket BPF filter, so that it cannot change after a
    process drops capabilities.

21) Add VLAN filtering to bridge, from Vlad Yasevich.

22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
    the ipv6 routes, from YOSHIFUJI Hideaki.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
  ipv6: fix race condition regarding dst->expires and dst->from.
  net: fix a wrong assignment in skb_split()
  ip_gre: remove an extra dst_release()
  ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
  atl1c: restore buffer state
  net: fix a build failure when !CONFIG_PROC_FS
  net: ipv4: fix waring -Wunused-variable
  net: proc: fix build failed when procfs is not configured
  Revert "xen: netback: remove redundant xenvif_put"
  net: move procfs code to net/core/net-procfs.c
  qmi_wwan, cdc-ether: add ADU960S
  bonding: set sysfs device_type to 'bond'
  bonding: fix bond_release_all inconsistencies
  b44: use netdev_alloc_skb_ip_align()
  xen: netback: remove redundant xenvif_put
  net: fec: Do a sanity check on the gpio number
  ip_gre: propogate target device GSO capability to the tunnel device
  ip_gre: allow CSUM capable devices to handle packets
  bonding: Fix initialize after use for 3ad machine state spinlock
  bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
  ...
2013-02-20 18:58:50 -08:00
Heiko Carstens 870a2b5e4f phylib: remove !S390 dependeny from Kconfig
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2013-02-14 15:55:18 +01:00
Grant Likely e80beb27d2 gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.

v2: Split GPIO portion into a separate patch

Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
2013-02-13 10:11:53 +00:00
Michał Mirosław 9f3b795a62 driver-core: constify data for class_find_device()
All in-kernel users of class_find_device() don't really need mutable
data for match callback.

In two places (kernel/power/suspend_test.c, drivers/scsi/osd/osd_uld.c)
this patch changes match callbacks to use const search data.

The const is propagated to rtc_class_open() and power_supply_get_by_name()
parameters.

Note that there's a dev reference leak in suspend_test.c that's not
touched in this patch.

Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-02-06 12:18:56 -08:00
Joe Perches e68ed8f0d8 drivers:net:misc: Remove unnecessary alloc/OOM messages
alloc failures already get standardized OOM
messages and a dump_stack.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-04 13:22:35 -05:00
David S. Miller f1e7b73acc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-29 15:32:13 -05:00
David J. Choi 7ab59dc15e drivers/net/phy/micrel_phy: Add support for new PHYs
Summary of changes:
.Newly added phys
	-KSZ8081/KSZ8091, which has some phy ids.
	-KSZ8061
	-KSZ9031, which is Gigabit phy.
	-KSZ886X, which has a switch function.
	-KSZ8031, which has a same phy ids with KSZ8021.

Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-28 18:42:10 -05:00
Giuseppe CAVALLARO ef3d90491a net: phy: realtek: add rtl8211e driver
This patch adds the minimal driver to manage the
Realtek RTL8211E 10/100/1000 Transceivers.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-01-28 18:34:53 -05:00