The V4L2_CID_PAN_SPEED and V4L2_CID_TILT_SPEED controls allow to move the
camera by setting its rotation speed around its axis.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In many cases the test pattern has selectable values for each colour
component. Implement controls for raw bayer components. Additional controls
should be defined for colour components that are not covered by these
controls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 958c7c7e65 ("[media] v4l2-ctrls: fix corner case in round-to-range code") broke
controls that use a negative range.
The cause was a s32/u32 mixup: ctrl->step is unsigned while all others are signed. So
the result type of the expression '(ctrl)->maximum - ((ctrl)->step / 2)' became unsigned,
making 'val >= (ctrl)->maximum - ((ctrl)->step / 2)' true, since '((u32)-128) > 128'
(if val = -128, maximum = 128 and step = 1).
So carefully cast (step / 2) to s32.
There was one cast of step to s32 where it should have been u32 because both offset and
step are unsigned, so casting to signed makes no sense there. You do need a cast to u32
there, because otherwise architectures that have no 64-bit division start complaining
(step is a u64).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The radio-miropcm20 driver has firmware that decodes the RDS signals. So in that
case the RDS data becomes available in the form of controls.
Add support for these controls to the control framework, allowing the miro driver
to use them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The si4713 supports several RDS features not yet implemented in the driver.
This patch adds the missing RDS functionality to the list of RDS controls.
The ALT_FREQS control is a compound control containing an array of up
to 25 (the maximum according to the RDS standard) frequencies. To support
that the V4L2_CTRL_TYPE_U32 was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than always having to use a v4l2_ext_control struct to set
a control value from within a driver, switch to just setting the
new value. This is faster and it makes it possible to set more
complex types such as a string control as is added by this
patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If you have a maximum that is at the limit of what the type supports,
and the step is > 1, then you can get wrap-around errors since the
code assumes that the maximum that the type supports is
ctrl->maximum + ctrl->step / 2.
In practice this is always fine, but in artificially crafted ranges
you will hit this bug. Since this is core code it should just work.
This bug has always been there but since it doesn't cause problems in
practice it was never noticed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement unlocked variants of v4l2_ctrl_s_ctrl() and
v4l2_ctrl_s_ctrl_int64(). As drivers need to set controls as they access
driver internal state elsewhere than in the control framework unlocked
variants of these functions become handy.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Drivers may use the v4l2_ctrl_modify_range() internally as part of other
operations that need to be both serialised using a driver's lock which can
also be used to serialise access to the control handler. Provide an unlocked
version of the function, __v4l2_ctrl_modify_range() which then may be used
by drivers for the purpose.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0ba2aeb6da increased the internal control ranges
to 64 bit, but that caused problems in drivers that use the minimum/maximum/step/default_value
control values in a division or modulus operations since not all architectures support
those natively.
Luckily, in almost all cases it is possible to just cast to 32 bits (the control value
is known to be 32 bits, so it is safe to cast). Only in v4l2-ctrls.c was it necessary to
use do_div in one function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the 'Detect' control class and the new motion detection controls.
Those controls will be used by the solo6x10 and go7007 drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Various comments referred to videodev2.h, but the control definitions have
been moved to v4l2-controls.h.
Also add the same reminder message to each class of controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These are needed by the upcoming patches for the motion detection
matrices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
copy_to/from_user returns the number of bytes not copied, it does not
return a 'normal' linux error code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When getting a string and the size given by the application is too
short return the max length the string can have (elem_size) instead
of the string length + 1. That makes more sense.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Extend the control type operations to handle N-dimensional array elements.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add core support for N-dimensional arrays.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add dims, nr_of_dims and elems fields to the core control structures in preparation
for N-dimensional array support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When setting a control the control's new value is compared to the current
value twice: once by new_to_cur(), once by cluster_changed(). Not a big
deal when dealing with simple values, but it can be a problem when dealing
with compound types or arrays. So fix this: cluster_changed() sets the
has_changed flag, which is used by new_to_cur() instead of having to do
another compare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In order to implement array support and (for the future) configuration stores
we need to have more generic copy routines that all operate on the v4l2_ctrl_ptr
union. So instead of e.g. using ctrl->cur.string it uses ptr.p_char. This makes
e.g. cur_to_user generic so it can be used to copy any v4l2_ctrl_ptr value to
userspace, not just the (hardcoded) current value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since compound controls can have non-standard types we need to be able to do
type-specific checks etc. In order to make that easy type operations are added.
There are four operations:
- equal: check if two values are equal
- init: initialize a value
- log: log the value
- validate: validate a new value
The v4l2_ctrl struct adds p_new and p_cur unions at the end of the struct.
This union provides a standard way of accessing control types through a pointer,
which greatly simplifies internal control processing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch implements initial support for compound types.
The changes are fairly obvious: basic support for is_ptr types, the
type_is_int function is replaced by a is_int bitfield, and
v4l2_query_ext_ctrl is added.
Note that this patch does not yet add support for N-dimensional
arrays, that comes later. So v4l2_query_ext_ctrl just sets elems to
1 and nr_of_dims and dims[] are all zero.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While VIDIOC_QUERYCTRL is limited to 32 bit min/max/step/def values
for controls, the upcoming VIDIOC_QUERY_EXT_CTRL isn't. So increase
the internal representation to 64 bits in preparation.
Because of these changes the msi3101 driver has been modified slightly
to fix a formatting issue (%d becomes %lld), vivi had to be modified
as well to cope with the new 64-bit min/max values and the PIXEL_RATE
control in a few sensor drivers required proper min/max/def values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add volatile boolean control to indicate if tuner frequency synthesizer
is locked to requested frequency. That means tuner is able to receive
given frequency. Control is named as "PLL lock", since frequency
synthesizers are based of phase-locked-loop. Maybe more general name
could be wise still?
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners has one or more adjustable filters on
signal path, in order to filter noise from desired radio channel.
Add channel bandwidth control to tell the driver which is radio
channel width we want receive. Filters could be then adjusted by
the driver or hardware, using RF frequency and channel bandwidth
as a base of filter calculations.
On automatic mode (normal mode), bandwidth is calculated from sampling
rate or tuning info got from userspace. That new control gives
possibility to set manual mode and let user have more control for
filters.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Modern silicon RF tuners used nowadays has many controllable gain
stages on signal path. Usually, but not always, there is at least
3 gain stages. Also on some cases there could be multiple gain
stages within the ones specified here. However, I think that having
these three controllable gain stages offers enough fine-tuning for
real use cases.
1) LNA gain. That is first gain just after antenna input.
2) Mixer gain. It is located quite middle of the signal path, where
RF signal is down-converted to IF/BB.
3) IF gain. That is last gain in order to adjust output signal level
to optimal level for receiving party (usually demodulator ADC).
Each gain stage could be set rather often both manual or automatic
(AGC) mode. Due to that add separate controls for controlling
operation mode.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adding V4L2 controls for horizontal and vertical search range in pixels
for motion estimation module in video encoder.
Signed-off-by: Swami Nathan <swaminath.p@samsung.com>
Signed-off-by: Amit Grover <amit.grover@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add v4l2 controls to set desired profile for VP8 encoder.
Acceptable levels for VP8 encoder are
0: Version 0
1: Version 1
2: Version 2
3: Version 3
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds v4l2 controls to set MIN, MAX QP values and
I, P frame QP for vp8 encoder.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Remove the redundant 'const' qualifiers from the function
signature and from the qmenu_int arrays' declarations.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Prevent following build warning:
drivers/media/v4l2-core/v4l2-ctrls.c: In function v4l2_ctrl_new_std_menu:
drivers/media/v4l2-core/v4l2-ctrls.c:1768:15: warning: 'qmenu_int_len' may be used uninitialized in this function
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The patch modifies the helper function v4l2_ctrl_new_std_menu
to accept integer menu controls with standard menu items.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The radio filter function that filters controls that are valid for a radio
device should also accept V4L2_CTRL_CLASS_FM_RX controls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a menu option to the V4L2_CID_EXPOSURE_METERING
control for multi-zone metering.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit introduces new class of standard controls
V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls
pertaining to FM receiver chips. Also, two controls belonging to said
class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and
V4L2_CID_RDS_RECEPTION.
This patch is based on the code found in the patch by Manjunatha Halli [1]
[1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.html
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Control whether video sequence headers should be repeated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When calling v4l2_ctrl_add_handler(), lockdep would detect a potential
recursive locking problem on a situation that is by design intended and
not a recursive lock. This happened because all struct
v4l2_ctrl_handler.lock mutexes were created as members of the same lock
class in v4l2_ctrl_handler_init(), and v4l2_ctrl_add_handler() takes the
hdl->lock on two different v4l2_ctrl_handler instances.
This change breaks the large lockdep lock class for struct
v4l2_ctrl_handler.lock and breaks it into v4l2_ctrl_handler
instantiation specific lock classes with meaningful class names.
This will validly eliminate lockdep alarms for v4l2_ctrl_handler locking
validation, as long as the relationships between drivers adding v4l2
controls to their own handler from other v4l2 drivers' control handlers
remains straightforward.
struct v4l2_ctrl_handler.lock lock classes are created with names such
that the output of cat /proc/lockdep indicates where in the v4l2 driver
code v4l2_ctrl_handle_init() is being called on instantiations:
ffffffffa045f490 FD: 10 BD: 8 +.+...: cx2341x:1534:(hdl)->lock
ffffffffa0497d20 FD: 12 BD: 2 +.+.+.: saa7115:1581:(hdl)->lock
ffffffffa04ac660 FD: 14 BD: 2 +.+.+.: msp3400_driver:756:(hdl)->lock
ffffffffa0484b90 FD: 12 BD: 1 +.+.+.: ivtv_gpio:366:(&itv->hdl_gpio)->lock
ffffffffa04eb530 FD: 11 BD: 2 +.+.+.: cx25840_core:1982:(&state->hdl)->lock
ffffffffa04fbc80 FD: 11 BD: 3 +.+.+.: wm8775:246:(&state->hdl)->lock
Some lock chains, that were previously causing the recursion alarms, are
now visible in the output of cat /proc/lockdep_chains:
irq_context: 0
[ffffffffa0497d20] saa7115:1581:(hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04ac660] msp3400_driver:756:(hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa0484b90] ivtv_gpio:366:(&itv->hdl_gpio)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04eb530] cx25840_core:1982:(&state->hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
irq_context: 0
[ffffffffa04fbc80] wm8775:246:(&state->hdl)->lock
[ffffffffa045f490] cx2341x:1534:(hdl)->lock
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
[hans.verkuil@cisco.com: keep mutex_init in v4l2_ctrl_handler_init_class]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It has been over 3 years since the V4L2_CID_[HV]CENTER were deprecated.
Clean up the DocBook and remove the V4L2_CID_VCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED control related paragraphs.
Remove the V4L2_CID_[HV]CENTER controls definitions from v4l2-controls.h,
these controls are not used by any driver in the mainline now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sometimes platform/bridge drivers need to be notified when a control from
a sub-device changes value. In order to support this a notify callback was
added.
[dheitmueller@kernellabs.com: fix merge conflict in v4l2-ctrls.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vincent Palatin
Sakari Ailus
Hans Verkuil
Hans Verkuil
Antti Palosaari
Amit Grover
Kiran AVND
Arun Kumar K
Jonathan McCrohan
Sylwester Nawrocki
Joe Perches
Sylwester Nawrocki
Andrey Smirnov
Andy Walls