* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI MSI: Fix MSI-X with NIU cards
PCI: Fix pci-e port driver slot_reset bad default return value
The NIU device refuses to allow accesses to MSI-X registers before MSI-X
is enabled. This patch fixes the problem by moving the read of the mask
register to after MSI-X is enabled.
Reported-by: David S. Miller <davem@davemloft.net>
Tested-by: David S. Miller <davem@davemloft.net>
Reviewed-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PAGE_MASK is 0xFFFFF000 on i386 -- even with PAE.
So it's not sufficient to ensure that you use phys_addr_t or uint64_t
everywhere you handle physical addresses -- you also have to avoid using
the construct 'addr & PAGE_MASK', because that will strip the high 32
bits of the address.
This patch avoids that problem by using PHYSICAL_PAGE_MASK instead of
PAGE_MASK where appropriate. It leaves '& PAGE_MASK' in a few instances
that don't matter -- where it's being used on the virtual bus addresses
we're dishing out, which are 32-bit anyway.
Since PHYSICAL_PAGE_MASK is not present on other architectures, we have
to define it (to PAGE_MASK) if it's not already defined.
Maybe it would be better just to fix PAGE_MASK for i386/PAE?
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current quirk doesn't include all 82576 device IDs. This update
resolves that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an upstream port reports an AER error to root port, kernel
starts error recovery procedures. The default return value of
function pcie_portdrv_slot_reset is PCI_ERS_RESULT_NONE. If all
port service drivers of the downstream port under the upstream
port have no slot_reset method in pci_error_handlers, AER recovery
would stop without resume. Below patch against 2.6.30-rc3 fixes it.
Signed-off-by: Zhang Yanmin <yanmin.zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCIe 1.1 base neither requires the endpoint to implement the entire
PCIe capability structure nor specifies default values of registers
that are not implemented by the device. So we only save and restore
registers that must be implemented by different device types if the
device PCIe capability version is 1.
PCIe 1.1 Capability Structure Expansion ECN and PCIe 2.0 requires
all registers in the PCIe capability to be either implemented or
hardwired to 0. Their PCIe capability version is 2.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add drivers/pci/*.c source files to DocBook/kernel-api.tmpl
and update those pci/*.c source files that need kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Commit 30a18d6c3f introduced a new
function to set the PCI bus resources. Unfortunately, neither the
author, nor the committers seemed to know that we already have somewhere
to do that -- pcibios_fixup_bus(). This patch moves the hook (used only
by the K8 code) into x86-specific code where it should have been in the
first place.
Cc: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Without this patch, Broadcom BCM5906 Ethernet controllers set up via MSI
cause the machine to hang. Tejun agreed that the best is to blacklist
the whole chipset and after adding it, seeing the other VIA quirks
disabling MSI, this very much looks like the right way.
Cc: <stable@kernel.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the BIOS does something obviously stupid, like claiming that the
registers for the IOMMU are at physical address zero, then print a nasty
message and abort, rather than trying to set up the IOMMU and then later
panicking.
It's becoming more and more obvious that trusting this stuff to the BIOS
was a mistake.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci_slot: grab refcount on slot's bus
PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
PCI: allow PCI core hotplug to remove PCI root bus
PCI: Fix oops in pci_vpd_truncate
PCI: don't corrupt enable_cnt when doing manual resource alignment
PCI: annotate pci_rescan_bus as __ref, not __devinit
PCI-IOV: fix missing kernel-doc
PCI: Setup disabled bridges even if buses are added
PCI: SR-IOV quirk for Intel 82576 NIC
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This issue was pointed out by Linus.
In dma_pte_clear_range() in intel-iommu.c
start = PAGE_ALIGN(start);
end &= PAGE_MASK;
npages = (end - start) / VTD_PAGE_SIZE;
In partial page case, start could be bigger than end and npages will be
negative.
Currently the issue doesn't show up as a real bug in because start and
end have been aligned to page boundary already by all callers. So the
issue has been hidden. But it is dangerous programming practice.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix this build error:
drivers/pci/intr_remapping.c: In function 'ir_parse_ioapic_scope':
drivers/pci/intr_remapping.c:617: error: invalid use of undefined type
'struct acpi_dmar_hardware_unit'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It's possible for a device in the drhd->devices[] array to be NULL if
it wasn't found at boot time, which means we have to check for that
case.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a logical hot unplug (remove) is performed on a bridge claimed
by acpiphp and then acpiphp is unloaded, we will encounter an oops.
This is because acpiphp will access the bridge's subordinate bus,
which was released by the user's prior hot unplug.
The solution is to grab a reference on the subordinate PCI bus.
This will prevent the bus from release until acpiphp is unloaded.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reported-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is no reason to prevent removal of root bus devices. A subsequent
rescan will find them just fine.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes breakage of of enable_cnt in quirk_resource_alignment.
Currently, quirk_resource_alignment calls pci_disable_device.
pci_disable_device decrements enable_cnt, so that enable_cnt becomes -1.
The patch disables memory decoding, writing command register directly.
So enable_cnt is not broken.
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_rescan_bus was annotated as __devinit, which is wrong,
because it will never be part of device initialization.
Howevever, we can't simply drop the annotation, because then we
get section warnings about calling pci_scan_child_bus (which is
correctly marked as __devinit).
pci_rescan_bus will only get built when CONFIG_HOTPLUG is set,
meaning that __devinit is a nop, so we know that pci_scan_child_bus
has not been freed.
Annotate as __ref to silence modpost.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix PCI iov kernel-doc warning:
Warning(drivers/pci/iov.c:638): No description found for parameter 'nr_virtfn'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-cpumask: (36 commits)
cpumask: remove cpumask allocation from idle_balance, fix
numa, cpumask: move numa_node_id default implementation to topology.h, fix
cpumask: remove cpumask allocation from idle_balance
x86: cpumask: x86 mmio-mod.c use cpumask_var_t for downed_cpus
x86: cpumask: update 32-bit APM not to mug current->cpus_allowed
x86: microcode: cleanup
x86: cpumask: use work_on_cpu in arch/x86/kernel/microcode_core.c
cpumask: fix CONFIG_CPUMASK_OFFSTACK=y cpu hotunplug crash
numa, cpumask: move numa_node_id default implementation to topology.h
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
cpumask: remove x86 cpumask_t uses.
cpumask: use cpumask_var_t in uv_flush_tlb_others.
cpumask: remove cpumask_t assignment from vector_allocation_domain()
cpumask: make Xen use the new operators.
cpumask: clean up summit's send_IPI functions
cpumask: use new cpumask functions throughout x86
x86: unify cpu_callin_mask/cpu_callout_mask/cpu_initialized_mask/cpu_sibling_setup_mask
cpumask: convert struct cpuinfo_x86's llc_shared_map to cpumask_var_t
cpumask: convert node_to_cpumask_map[] to cpumask_var_t
x86: unify 32 and 64-bit node_to_cpumask_map
...
We were comparing {bus,devfn} and assuming that a match meant it was the
same device. It doesn't -- the same {bus,devfn} can exist in
multiple PCI domains. Include domain number in device identification
(and call it 'segment' in most places, because there's already a lot of
references to 'domain' which means something else, and this code is
infected with ACPI thinking already).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the DMAR table identifies that a PCI-PCI bridge belongs to a given
IOMMU, that means that the bridge and all devices behind it should be
associated with the IOMMU. Not just the bridge itself.
This fixes the device_to_iommu() function accordingly.
(It's broken if you have the same PCI bus numbers in multiple domains,
but this function was always broken in that way; I'll be dealing with
that later).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
interrupt remapping must be enabled before enabling x2apic, but
interrupt remapping doesn't depend on x2apic, it can be used
separately. Enable interrupt remapping in init_dmars even x2apic
is not supported.
[dwmw2: Update Kconfig accordingly, fix build with INTR_REMAP && !X2APIC]
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If queue invalidation is disabled after it's already initialized,
dmar_enable_qi won't re-enable it due to iommu->qi is allocated.
It may result in system hang when use queue invalidation. Add this
check to avoid this case.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
When extended interrupt mode (x2apic mode) is not supported in a
system, it must set compatibility format interrupt to bypass
interrupt remapping, otherwise compatibility format interrupts
will be blocked.
This will be used when interrupt remapping is enabled while x2apic
is not supported.
Signed-off-by: Weidong Han <weidong.han@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch enables suspend/resume for interrupt remapping. During suspend,
interrupt remapping is disabled. When resume, interrupt remapping is enabled
again.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements the suspend and resume feature for Intel IOMMU
DMAR. It hooks to kernel suspend and resume interface. When suspend happens, it
saves necessary hardware registers. When resume happens, it restores the
registers and restarts IOMMU by enabling translation, setting up root entry, and
re-enabling queued invalidation.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Fix address wrap on 32-bit kernel.
intel-iommu: Enable DMAR on 32-bit kernel.
intel-iommu: fix PCI device detach from virtual machine
intel-iommu: VT-d page table to support snooping control bit
iommu: Add domain_has_cap iommu_ops
intel-iommu: Snooping control support
Fixed trivial conflicts in arch/x86/Kconfig and drivers/pci/intel-iommu.c
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (88 commits)
PCI: fix HT MSI mapping fix
PCI: don't enable too much HT MSI mapping
x86/PCI: make pci=lastbus=255 work when acpi is on
PCI: save and restore PCIe 2.0 registers
PCI: update fakephp for bus_id removal
PCI: fix kernel oops on bridge removal
PCI: fix conflict between SR-IOV and config space sizing
powerpc/PCI: include pci.h in powerpc MSI implementation
PCI Hotplug: schedule fakephp for feature removal
PCI Hotplug: rename legacy_fakephp to fakephp
PCI Hotplug: restore fakephp interface with complete reimplementation
PCI: Introduce /sys/bus/pci/devices/.../rescan
PCI: Introduce /sys/bus/pci/devices/.../remove
PCI: Introduce /sys/bus/pci/rescan
PCI: Introduce pci_rescan_bus()
PCI: do not enable bridges more than once
PCI: do not initialize bridges more than once
PCI: always scan child buses
PCI: pci_scan_slot() returns newly found devices
PCI: don't scan existing devices
...
Fix trivial append-only conflict in Documentation/feature-removal-schedule.txt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PCI PM: Make pci_prepare_to_sleep() disable wake-up if needed
radeonfb: Use __pci_complete_power_transition()
PCI PM: Introduce __pci_[start|complete]_power_transition() (rev. 2)
PCI PM: Restore config spaces of all devices during early resume
PCI PM: Make pci_set_power_state() handle devices with no PM support
PCI PM: Put devices into low power states during late suspend (rev. 2)
PCI PM: Move pci_restore_standard_config to pci-driver.c
PCI PM: Use pci_set_power_state during early resume
PCI PM: Consistently use variable name "error" for pm call return values
kexec: Change kexec jump code ordering
PM: Change hibernation code ordering
PM: Change suspend code ordering
PM: Rework handling of interrupts during suspend-resume
PM: Introduce functions for suspending and resuming device interrupts
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
dma-debug: make memory range checks more consistent
dma-debug: warn of unmapping an invalid dma address
dma-debug: fix dma_debug_add_bus() definition for !CONFIG_DMA_API_DEBUG
dma-debug/x86: register pci bus for dma-debug leak detection
dma-debug: add a check dma memory leaks
dma-debug: add checks for kernel text and rodata
dma-debug: print stacktrace of mapping path on unmap error
dma-debug: Documentation update
dma-debug: x86 architecture bindings
dma-debug: add function to dump dma mappings
dma-debug: add checks for sync_single_sg_*
dma-debug: add checks for sync_single_range_*
dma-debug: add checks for sync_single_*
dma-debug: add checking for [alloc|free]_coherent
dma-debug: add add checking for map/unmap_sg
dma-debug: add checking for map/unmap_page/single
dma-debug: add core checking functions
dma-debug: add debugfs interface
dma-debug: add kernel command line parameters
dma-debug: add initialization code
...
Fix trivial conflicts due to whitespace changes in arch/x86/kernel/pci-nommu.c
If the device is not supposed to wake up the system, ie. when
device_may_wakeup(&dev->dev) returns 'false', pci_prepare_to_sleep()
should pass 'false' to pci_enable_wake() so that it calls the
platform to disable the wake-up capability of the device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device. Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device. For symmetry, introduce __pci_start_power_transition().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
At present the configuration spaces of PCI devices that have no
drivers or no PM support in the drivers (either legacy or through a
pm object) are not saved during suspend and, consequently, they are
not restored during resume. This generally may lead to the state of
the system being slightly inconsistent after the resume, so it's
better to save and restore the configuration spaces of these devices
as well.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
