Since the first version of this driver, the remote controller
code is disabled, adding an early return inside vp702x_rc_query().
Let's disable the code with #if 0, to remove this warning:
drivers/media/usb/dvb-usb/vp702x.c:268 vp702x_rc_query() info: ignoring unreachable code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/gspca/zc3xx.c:5994 transfer_update() info: ignoring unreachable code.
That happens because there's a return that it is never called,
as the work queue runs an infinite loop, except when the device is
put to sleep or an error happens.
When an error happens, a break statement is enough to go out of
the loop. So, let's remove the goto, as break is the typical
instruction used to end a loop.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/usb/go7007/go7007-driver.c:452 frame_boundary() warn: variable dereferenced before check 'vb' (see line 449)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* patchwork: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Add support for the new VIDIOC_QUERY_EXT_CTRL ioctl. Since uvc doesn't use
the control framework, support for this ioctl isn't automatic.
This is makes v4l2-compliance happy as well.
[Added blank lines for improved readability]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2-compliance tool expects that if VIDIOC_CROPCAP is defined, then
VIDIOC_G_SELECTION for TGT_CROP_BOUNDS/DEFAULT is also defined (or COMPOSE
in the case of an output device).
In fact, all that a driver has to do to implement cropcap is to support
those two targets since the v4l2 core will implement cropcap and fill in
the pixelaspect to 1/1 by default.
Implementing cropcap is only needed if the pixelaspect isn't square.
So implement g_selection instead of cropcap in uvc to fix the v4l2-compliance
failure.
[Added blank lines for improved readability]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add Leadtek WinFast DTV2000DS Plus device based on Realtek RTL2832U.
I have not tested the remote, but it is the Y04G0051 model.
Signed-off-by: Christian Dale <kernel@techmunk.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ID 1b80:d3a4 Afatech
Simply added the PID (0xd3a4) of this DVB-T USB device to the list of rtl2832u-supported devices. VID (0x1b80) is same as KWORLD2.
Tested and verified to work in amd64 with kernels 3.13.0 and 3.16.0.
Signed-off-by: Dimitris Lampridis <dlampridis@logikonlabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use enum to represent table offsets rather than hard-coding numbers to avoid
problems with the numbers becoming out of sync with the table.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fixing a few checkpatch errors of type: space required after that ','
Signed-off-by: Luis de Bethencourt <luis.bg@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no usb_put_dev() on failure paths in usbvision_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed the video_device struct to simplify the error handling and in
order to (eventually) get rid of video_device_alloc/release.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change ts2022 driver to ts2020 driver. ts2020 driver supports
both tuner chip models.
That affects TechnoTrend TT-connect S2-4600 DVB-S/S2 device, which
Olli just added.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change ts2022 driver to ts2020 driver as ts2020 driver now supports
both models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TechnoTrend TT-connect S2-4600 is a USB2.0 DVB-S/S2 tuner using the popular
Montage M88DS3103/M88TS2022 demod/tuner.
The demodulator needs a firmware. Antti posted a firmware when releasing
support for PCTV 461e, available here:
http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare the dw2102 driver for tuner drivers that are implemented as I2C
drivers (such as m88ts2022). The I2C client is stored in to the state
and released at disconnect.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Two separate state structs are defined for different devices inside the
dw2102. Combine them, as both only contain one element.
This will also make it easier to further cleanup the driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Astrometa device has issues with i2c transfers. Lowering the
poll time somehow makes these errors disappear.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All uses of the v4l2_clk API so far only register one clock with a fixed
name. This allows us to get rid of it, which also will make CCF and DT
integration easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit c5036d61e0 ("media: au0828: drop
vbi_buffer_filled() and re-use buffer_filled()") broke video and vbi streaming.
The vb2_buffer struct was copied instead of taking a pointer to it, but
vb2_buffer_done() needs the real object, not a copy, since it is hooking
the buffer into a different list.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return success for FE callback on case we don't have any special
implementation. fc0013 tuner driver calls that callback in order to
switch antenna input, even we don't provide antenna switch.
Returning error caused fc0013 driver given up tuning.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If CONFIG_VIDEO_CX231XX_RC is undefined, then these compiler warnings
are generated:
In file included from drivers/media/usb/cx231xx/cx231xx-cards.c:23:0:
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_release_resources’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1158:2: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_init_dev’:
drivers/media/usb/cx231xx/cx231xx.h:981:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_init(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1351:2: note: in expansion of macro ‘cx231xx_ir_init’
cx231xx_ir_init(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1705:2: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_disconnect’:
drivers/media/usb/cx231xx/cx231xx.h:982:30: warning: statement with no effect [-Wunused-value]
#define cx231xx_ir_exit(dev) (0)
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1754:3: note: in expansion of macro ‘cx231xx_ir_exit’
cx231xx_ir_exit(dev);
^
Fix by using static inlines instead of defines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The available (i.e. not used) buffers are returned by stk1160_clear_queue(),
on the stop_streaming() path. However, this is insufficient and the current
buffer must be released as well. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Frame intervals exposed as an interval and step (so-called step-wise)
are restricted by the V4L2 API to a single enumeration entry. Return an
error when the index is not zero.
Reported-by: Alexey Smirnoff <fling@member.fsf.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[mchehab@osg.samsung.com: add a missing collon at the end of the return
statement, in order to avoid compilation breakage]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device is based on an Aveo chipset, implements UVC but advertises a
vendor-specific class on all interfaces.
Support it by listing the USB VID:PID explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
videobuf2 has long been subject to AB-BA style deadlocks due to the
queue lock and mmap_sem being taken in different orders for the mmap and
get_unmapped_area operations. The problem has been fixed by making those
two operations callable without taking the queue lock, using an
mmap_lock internal to videobuf2.
The uvcvideo driver still calls the mmap and get_unmapped_area
operations with the queue lock held, resulting in a potential deadlock.
As the operations can now be called without locking the queue, fix it.
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch will add basic support for the Elgato EyeTV Hybrid INT
2008 USB Stick.
Signed-off-by: Gilles Risch <gilles.risch@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Embed video_device structs vdev and vbi_dev in au0828_dev.
With this change, dynamic allocation and error path logic
in au0828_analog_register() is removed as it doesn't need
to allocate and handle allocation errors. Unregister path
doesn't need to free the now static video_device structures,
hence, changed video_device.release in au0828_video_template
to point to video_device_release_empty.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vbi_buffer_filled() and buffer_filled() did the same functionality
except for incrementing the buffer sequence, this patch drops the
vbi_buffer_filled() and re-uses buffer_filled() for vbi buffers
as well by adding the check for vb2-queue type while incrementing
the sequence numbers. Along side this patch aligns the input parameters
of buffer_filled() function appropriately.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hauppauge HVR-955Q is a ATSC/QAM USB tuner with LGDT3306A demodulator and SiLabs Si2157-A30 tuner.
Only digital TV has been tested (both ATSC and QAM256).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several (15) drivers in media/usb/gspca use IF_ENABLED(CONFIG_INPUT)
to decide if they should call input* interfaces, but those drivers
do not build successfully when CONFIG_INPUT=m and the gspca drivers
are builtin (=y). Making USB_GSPCA depend on INPUT || INPUT=n
fixes the build dependencies and allows all of them to build
cleanly.
Fixes these build errors (selections, not all are listed):
drivers/built-in.o: In function `gspca_disconnect':
(.text+0x32ed0f): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `sd_isoc_irq':
konica.c:(.text+0x333098): undefined reference to `input_event'
konica.c:(.text+0x3330ab): undefined reference to `input_event'
drivers/built-in.o: In function `sd_stopN':
konica.c:(.text+0x3338d3): undefined reference to `input_event'
konica.c:(.text+0x3338e5): undefined reference to `input_event'
drivers/built-in.o: In function `ov51x_handle_button':
ov519.c:(.text+0x335ddb): undefined reference to `input_event'
drivers/built-in.o:ov519.c:(.text+0x335ded): more undefined references to `input_event' follow
pac7302.c:(.text+0x336ea1): undefined reference to `input_event'
pac7302.c:(.text+0x336eb3): undefined reference to `input_event'
drivers/built-in.o: In function `sd_pkt_scan':
spca561.c:(.text+0x338fd8): undefined reference to `input_event'
drivers/built-in.o:spca561.c:(.text+0x338feb): more undefined references to `input_event' follow
t613.c:(.text+0x33a6fd): undefined reference to `input_event'
drivers/built-in.o:t613.c:(.text+0x33a70f): more undefined references to `input_event' follow
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By using struct v4l2_fh both the prio handling and the linked list
implementation in pvrusb2 can be removed since both are now done in
the v4l2 core if you use struct v4l2_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As far as I can tell pvrusb2 does its own locking, so there is
no need to use .ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video_unregister_device() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cos table used at fixp-arith.h has only 8 bits of precision.
That causes problems if it is reused on other drivers.
As some media drivers require a higher precision sin/cos
implementation, replace the current implementation by one that
will provide 32 bits precision.
The values generated by the new implementation matches the
32 bit precision of glibc's sin for an angle measured in
integer degrees.
It also provides support for fractional angles via linear
interpolation. On experimental calculus, when used a table
with a 0.001 degree angle, the maximum error for sin is
0.000038, which is likely good enough for practical purposes.
There are some logic there that seems to be specific to the
usage inside ff-memless.c. Move those logic to there, as they're
not needed elsewhere.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The if and the else code are identical - so the condition has no effect
on the effective code.
This patch removes the condition and the duplicated code.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the media controller (MC) is not enabled, it will compile
fine, but will fail at the linkedition:
ERROR: "media_device_unregister" [drivers/media/usb/siano/smsusb.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is really a simple function, but using it avoids to have
if's inside the drivers.
Also, the kABI becomes a little more clearer.
This shouldn't generate any overhead, and the type check
will happen when compiling with MC DVB enabled.
So, let's do it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function ‘dvb_usbv2_adapter_dvb_exit’:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:531:25: warning: unused variable ‘d’ [-Wunused-variable]
struct dvb_usb_device *d = adap_to_d(adap);
^
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:403:13: warning: ‘dvb_usbv2_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usbv2_media_device_register(struct dvb_usb_adapter *adap)
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:97:13: warning: ‘dvb_usb_media_device_register’ defined but not used [-Wunused-function]
static void dvb_usb_media_device_register(struct dvb_usb_adapter *adap)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using media_dev argument for dvb_create_media_graph(),
use the adapter.
That allows to create a stub for this function, if compiled
without DVB support, avoiding to add extra if's at the drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of assuming just one adapter, change the code to store
one media controller per adapter.
This works fine for dvb-usb, as, on all drivers here, it is not
possible to write a media graph that would mix resources between
the two different adapters.
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a struct media_device and add it to the dvb adapter.
Please notice that the tuner is not mapped yet by the dvb core.
[mchehab@osg.samsung.com: use config option MEDIA_CONTROLLER_DVB due to a rebase]
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to initialize the media controller earlier, as the core
will call the smsdvb hotplug during register time. Ok, this is
an async operation, so, when the module is not loaded, the media
controller works.
However, if the module is already loaded, nothing will be
registered at the media controller, as it will load too late.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All siano modules have a sms_dbg parameter. Now that we're using
the standard pr_debug() macro, we can get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On most cases, sms_info() should actually be pr_debug(), but,
on other places, it should be pr_info().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to use a macro here. Just replace everything,
and let those debug messages to be activated via dynamic printk.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Originally, sms_err() would be also displaying the line where
the error occurs, but the messages are clear enough. Also,
the function is always printed. So, no need for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason for a sms' own sms_warn macro. Just replace
it by the standard pr_warn().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of defining its own set of printk functions, let's
use the common Kernel debug logic provided by pr_foo functions.
As a first step, let's just define the existing macros as the
Kernel ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding support for the media controller for a pure DVB device
is simple: just create a struct media_device and add it to the
dvb adapter. After creating all DVB devices, we need to call
the DVB core, for it to create the media graph.
More work is needed for pure DVB tuners, but this is hidden
at the Siano driver, just like several others non-hybrid
devices. So, this is streight forward.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
buf_prepare callback is called for every queued buffer. This is
an overkill. Call it at buf_setup, as this should be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two problems at the comment:
- it is badly idented;
- its comment doesn't mean anything.
Fix it.
Requested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/cx231xx/cx231xx-cards.c: In function ‘cx231xx_usb_probe’:
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:15: error: ‘struct v4l2_device’ has no member named ‘mdev’
dev->v4l2_dev.mdev = dev->media_dev;
^
drivers/media/usb/cx231xx/cx231xx-cards.c:1589:26: error: ‘struct cx231xx’ has no member named ‘media_dev’
dev->v4l2_dev.mdev = dev->media_dev;
^
scripts/Makefile.build:257: recipe for target 'drivers/media/usb/cx231xx/cx231xx-cards.o' failed
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cx231xx is simple with regards to DVB: all boards have just one
DVB adapter. So, we can use the default DVB helper function to
create the DVB media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have entities and pads, let's create media links
between them, for analog setup.
We may not have all the links for digital yet, as the dvb extention
may not be loaded yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's add media controller support for this driver and register it
for both V4L and DVB.
The media controller on this driver is not mandatory, as it can fully
work without it. So, if the media controller register fails, just print
an error message, but proceed with device registering.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by Peter Kovar, there's a potential risk of a division by
zero on calls to jpeg_set_qual() when quality is zero.
As quality can't be 0 or lower than that, add an extra clause to cover
this special case.
Signed-off-by: Luis de Bethencourt <luis.bg@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This allows calling the original functions providing the streaming is off.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create dm04_read_status to check lock through either interrupt values
or directly by the call back.
When the device is not streaming the frontends original call back is
used. When streaming has started it turns off I2C messaging by
setting st->i2c_talk_onoff to zero. I2C can only be turn on again
by one of the other allowed frontend calls.
All old code is removed from lme2510_msg and this function only needs
to set st->i2c_talk_onoff to 1.
The lock status is saved and when the frondend is locked is maintained
by lme2510_int_response who will now just kill the lock.
The call back for rs2000 tuner is nologer required.
All frontend types have been tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create call backs dm04_read_signal_strength, dm04_read_snr and
move dm04_read_ber and dm04_read_ucblocks for all frontends
Removing the I2C filtering from lme2510_msg and the old rs2000 callbacks.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A quirk of some older firmwares that report endpoint pipe type as PIPE_BULK
but the endpoint otheriwse functions as interrupt.
Check if usb_endpoint_type is USB_ENDPOINT_XFER_BULK and set as usb_rcvbulkpipe.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ocassionally the device fails to report back an interrupt urb status which
results in false no lock trigger on the RS2000 demodulator.
Increase time from 60 msecs to 200 msecs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As complained by smatch:
drivers/media/usb/dvb-usb-v2/rtl28xxu.c:1159 rtl2832u_tuner_attach() info: 'pdata' is not actually initialized (unreached code).
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use rtl28xxu_ prefix for all register access routine names.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As all the callbacks are already same we could merge device
properties struct too and save space.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Merge all chip type specific prefixed (rtl2831u_ and rtl2832u_)
callback to top level callback prefixed as rtl28xxu_.
rtl2831u_foo() => rtl28xxu_foo()
rtl2832u_foo() => rtl28xxu_foo()
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Detect automatically whether chip is old RTL2831U or newer
RTL2832U/RTL2832P. Detection is based I2C command that is found only
from newer RTL2832U models.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Buffer needed for USB control message is small so move it to state
and get rid of alloc/free used for each control message.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pass correct device pointer to dev_* logging in order to print
module name and bus id correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I prefer dev over priv and I want keep all my drivers in line with
that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver, rtl28xxu, offers frontend service for rtl2832_sdr
module, thus we are producer and rtl2832_sdr module is consumer.
Due to that, reference counting should be done in way rtl2832_sdr
takes refrence to rtl28xxu. Remove wrong refcount.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Logic is so simple that there is no idea to separate tuner selection to
own function, instead do it in a callback and get rid of one function.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
DVB FE callback functionality went broken after I moved tuners to
demod muxed I2C adapter. That happens because driver state was
carried by I2C adapter and when mux is used there is one adapter
more in a chain.
USB adapter <-> I2C adapter <-> muxed I2C adapter
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both mn88472 and mn88473 slave demods are connected to master I2C
bus, not the bus behind master demod I2C gate like tuners. Use
correct bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
RTL2832 demod integrated into RTL2832U has PID filter. PID filtering
is provided by rtl2832 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners are connected to demod I2C adapter. Use that muxed adapter
for each tuner. That allows us to get rid of hackish FE gate control
solution.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use platform data configuration for rtl2832 demod driver. Old
configuration are still left as it is used for rtl2832_sdr driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch demod resource use from exported symbols to callbacks its
provides.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
RTL2830 demod integrated to RTL2831U has PID filter. PID filtering
is provided by rtl2830 demod driver. Add support for it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rtl2830 driver supports now I2C model too. Start using it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Top level pointer on USB probe is struct usb_interface *. Add that
pointer to struct dvb_usb_device that drivers could use it, for
dev_* logging and more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert au0828 to use videobuf2. Tested with NTSC.
Tested video and vbi devices with xawtv, tvtime,
and vlc. Ran v4l2-compliance to ensure there are
no failures.
Video compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 18
Vbi compliance test results summary:
Total: 75, Succeeded: 75, Failed: 0, Warnings: 0
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828 picked up UNSET from videobuf-core.h and fails to compile
if videobuf-core.h isn't included. Change it to use -1U instead
to fix the problem.
drivers/media/usb/au0828/au0828-cards.c:47:17: error: ‘UNSET’ undeclared here (not in a function)
.tuner_type = UNSET,
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828_analog_register() frees au0828_dev when it fails to
locate isoc endpoint. au0828_usb_probe() continues with dvb
and rc probe and registration assuming dev is still valid.
When au0828_analog_register() fails to locate isoc endpoint,
it should return without free'ing au0828_dev. Otherwise, the
probe will fail as dev is null when au0828_dvb_register() is
called.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The USB and MMC front-ends to the siano driver both only make
sense when combined with the SMS_SIANO_MDTV driver. That driver
already requires RC_CORE to not be a module, so we also need
to add that dependency here.
drivers/built-in.o: In function `smssdio_remove':
:(.text+0x155bd8): undefined reference to `smscore_putbuffer'
:(.text+0x155bdc): undefined reference to `smscore_unregister_device'
drivers/built-in.o: In function `smssdio_interrupt':
:(.text+0x155e4c): undefined reference to `smsendian_handle_rx_message'
:(.text+0x155e50): undefined reference to `smscore_onresponse'
:(.text+0x155e54): undefined reference to `smscore_getbuffer'
:(.text+0x155e58): undefined reference to `smscore_putbuffer'
drivers/built-in.o: In function `smssdio_sendrequest':
:(.text+0x155f20): undefined reference to `smsendian_handle_tx_message'
drivers/built-in.o: In function `smssdio_probe':
:(.text+0x15610c): undefined reference to `sms_get_board'
:(.text+0x156114): undefined reference to `smscore_register_device'
:(.text+0x156118): undefined reference to `smscore_set_board_id'
:(.text+0x156128): undefined reference to `smscore_unregister_device'
:(.text+0x156140): undefined reference to `smscore_start_device'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is only an API consolidation and should make things more readable
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 5eeb301482 added a fixup at the error check
code. However, it introduced a new error:
drivers/media/usb/cx231xx/cx231xx-cards.c:1586 cx231xx_usb_probe() error: we previously assumed 'dev' could be null (see line 1430)
This happens when dev = kmalloc() fails. So, instead of relying
on it to succeed, just change the parameter of clear_bit() from
'dev->devno' to 'nr'.
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit b7085c0864 ("cx231xx: convert from pr_foo to dev_foo")
moves usb_get_dev(interface_to_usbdev(interface)) to the beginning
of cx231xx_usb_probe() to use udev->dev in dev_err(),
but it does not make sure usbdev is put on all failure paths.
Later dev_err(udev->dev) was replaced by dev_err(d).
So the patch moves usb_get_dev() below (before the first use)
and fixes another failure path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I found a problem on vc032x gspca usb webcam subdriver: "bytesperline"
property is wrong for YUYV and YVYU formats.
With recent v4l-utils library (>=0.9.1), that uses "bytesperline" for
pixel format conversion, the result is a wrong jerky image.
Patch tested on my laptop (USB webcam Logitech Orbicam 046d:0892).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=91181
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"n" is a user controlled integer. The code here doesn't handle the case
where "n" is negative and this causes a static checker warning.
drivers/media/usb/gspca/gspca.c:1571 vidioc_s_parm()
warn: no lower bound on 'n'
parm.capture.readbuffers is unsigned, so make n unsigned too, fixing this.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in the PS3 Eye driver for QVGA capture at higher
frame rates: 187, 150, and 137 FPS. This functionality is valuable
because the PS3 Eye is popular for computer vision projects and no
other camera in its price range supports such high frame rates.
Correct a QVGA mode that was listed as 40 FPS. It is really 37 FPS
(half of 75 FPS).
Tests confirm that the nominal frame rates are achieved.
Signed-off-by: Joe Howse <josephhowse@nummist.com>
Tested-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If start_streaming fails, then the buffers must be given back to vb2 with state
QUEUED, not ERROR. Otherwise a WARN_ON will be generated.
In the disconnect it is pointless to call pwc_cleanup_queued_bufs() as stop_streaming()
will be called anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Checkpatch complained about a few issues, like FSF address. Also,
multi-line comments are not following the Kernel CodingStyle.
While not too late, let's fix those issues.
Cc: John McMaster <johndmcmaster@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds support for AmScope MU800 / ToupTek UCMOS08000KPB USB microscope camera.
Signed-off-by: John McMaster <johndmcmaster@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We must unregister frontend first and after that driver itself. That
order went wrong after demod drivers were switched to kernel I2C
drivers, causing crashes.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As rtl2832 driver support now I2C binding we will switch to that one.
Tested-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The UVC spec is a bit vague wrt devices using bulk endpoints,
specifically, how to signal to a device to start streaming.
For devices using isoc endpoints, the sequence for start streaming is:
1) The host sends PROBE_CONTROL(SET_CUR) PROBE_CONTROL(GET_CUR)
2) Host selects desired config and calls COMMIT_CONTROL(SET_CUR)
3) Host selects an alt interface other then zero - e.g SELECT_ALTERNATE_INTERFACE(1)
4) The device starts streaming
However for devices using bulk endpoints, there must be *no* alt interface
other than setting zero. From the UVC spec:
"A VideoStreaming interface containing a bulk endpoint for streaming shall
support only alternate setting zero. Additional alternate settings containing
bulk endpoints are not permitted in a device that is compliant with the Video
Class specification."
So for devices using bulk endpoints, step #3 above is irrelevant, and thus
cannot be used as an indication for the device to start streaming.
So in practice, such devices start streaming immediately after a
COMMIT_CONTROL(SET_CUR).
In the uvc resume() handler, an unsolicited commit is sent, which causes
devices using bulk endpoints to start streaming unintentionally.
This patch modifies resume() handler to send a commit only if streaming
needs to be reestablished, i.e if the device was actually streaming before is
was suspended.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the function pvr2_hdw_cmd_powerdown() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
The semantic patch also changes the cast to long to a cast to unsigned
long in the data initializer, as unsigned long is the type of the data field.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-t.function = f;
-t.data = d;
-init_timer(&t);
+setup_timer(&t,f,d);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUxbzlAAoJEHm+PkMAQRiGtqYIAJ8YlKX9cXKYmXx8/FncINH+
2erj94KyHG080R1uwSq1+7zXWCZUUlxiJnDnsup5rG0dImcicqgOE48oHax1aN6b
yHfPONkTjNJ1HYepuGC3YWCG9wIjPZQ5S8KHrwRjyVoE+ddhe9gWgvArA3jl/fW/
2fYNWekoRoMcRiNb4/w2weyOOBywdSVpmj0WYiwdztysG2ymw5hUXRHJhvSf1AFm
RQJfUHkhCOYpQGY7XFba/1uGhTJfOgDmYAfspAOLzmrXE/DJcCutsVdBZO+12fAL
nhGpM/PkRYxMvwzDKIUoG35qsymYOMqo54oXhr0S2JjyXTGdGmB6qHxIfqnV5Tk=
=O/Lr
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc6' into patchwork
This is needed in order to get the media fixes applied on -rc6.
Linux 3.19-rc6
* tag 'v3.19-rc6': (891 commits)
Linux 3.19-rc6
dm: fix handling of multiple internal suspends
hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
hwmon: (i5500_temp) Convert to module_pci_driver
hwmon: (i5500_temp) Don't bind to disabled sensors
hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets
arm64: dts: add baud rate to Juno stdout-path
Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
Revert "Documentation: Add entry for dell-laptop sysfs interface"
dm cache: fix problematic dual use of a single migration count variable
dm cache: share cache-metadata object across inactive and active DM tables
of/unittest: Overlays with sub-devices tests
KVM: x86: SYSENTER emulation is broken
KVM: x86: Fix of previously incomplete fix for CVE-2014-8480
arm64: dump: Fix implicit inclusion of definition for PCI_IOBASE
x86/tsc: Change Fast TSC calibration failed from error to info
x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
x86, mm: Change cachemode exports to non-gpl
x86, tls: Interpret an all-zero struct user_desc as "no segment"
...
Conflicts:
drivers/media/pci/cx23885/cx23885.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yD+L
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix some race conditions caused by a regression on videobuf2
- fix a interrupt release bug on cx23885
- fix support for Mygica T230 and HVR4400
- fix compilation breakage when USB is not selected on tlg2300
- fix capabilities report on ompa3isp, soc-camera, rcar_vin and
pvrusb2
* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Correctly set QUERYCAP capabilities
[media] cx23885: fix free interrupt bug
[media] pvrusb2: fix missing device_caps in querycap
[media] vb2: fix vb2_thread_stop race conditions
[media] rcar_vin: Update device_caps and capabilities in querycap
[media] soc-camera: fix device capabilities in multiple camera host drivers
[media] Fix Mygica T230 support
[media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
[media] tlg2300: Fix media dependencies
The VIDIOC_QUERYCAP function should set device_caps, but this was missing.
In addition, it set the version field as well, but that should be done by
the core, not by the driver.
If a driver doesn't set device_caps the v4l2 core will issue a WARN_ON, so
it's important that this is set correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2adb177e57 removed 2 devices
from the cxusb device table but failed to fix up the T230 properties
that follow, meaning that this device no longer gets detected properly.
Adjust the cxusb_table index appropriate so detection works.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-video. Fix these.
Fixes: a61f68119a ("[media] em28xx-video: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-dvb. Fix these.
Fixes: ca2b46dacb ("[media] em28xx-dvb: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-audio. Fix these.
Fixes: 6d746f91f2 ("[media] em28xx-audio: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-audio. Fix these.
Fixes: 1b3fd2d342 ("[media] em28xx-audio: don't hardcode audio URB calculus")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-core. Fix these.
Fixes: 9c669b7314 ("[media] em28xx: add suspend/resume to em28xx_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Inspection shows that newlines are missing from several kernel messages
in em28xx-input. Fix these.
Fixes: 5025076aad ("[media] em28xx-input: implement em28xx_ops: suspend/resume hooks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The lockdep splat addressed in a previous commit revealed that at
least one message in em28xx-input.c was missing a new line:
em28178 #0: Closing input extensionINFO: trying to register non-static key.
Further inspection shows several other messages also miss a new line.
These will be fixed in a subsequent patch.
Fixes: aa929ad783 ("[media] em28xx: print a message at disconnect")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add xtal as a configuration parameter so it can be used
in the IF register value calculation.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver supports VBI and the comment "VBI support
is not yet working" is inaccurate. Remove it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The debug field in struct video_device is for internal use only and
drivers should mix that with their own debug module options.
It is handled by the V4L2 core and users can set it using
/sys/class/video4linux/<devX>/debug.
It has been deprecated for some time now, so it is time to remove it
completely from the drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove this comment block, it's unused. This removes the btcx_riscmem
reference as well, since that will no longer be available to other
drivers except bttv.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Magewell XI100DUSB-HDMI[1] video capture device reports the pixel
format "e436eb7d-524f-11ce-9f53-0020af0ba770". This is its GUID for
BGR 8:8:8.
The UVC 1.5 spec[2] only defines GUIDs for YUY2, NV12, M420 and I420.
This seems to be an extension documented in the Microsoft Windows Media
Format SDK[3] - or at least the Media Format SDK was the only hit that
Google gave when searching for the GUID. This Media Format SDK defines
this GUID as corresponding to `MEDIASUBTYPE_RGB24`. Note though, the
XI100DUSB outputs BGR e.g. byte-reversed. I don't know if its the
capture device in error or Microsoft mean BGR when they say RGB.
[1]: http://www.magewell.com/hardware/dongles/xi100dusb-hdmi/xi100dusb-hdmi_features.html?lang=en
[2]: http://www.usb.org/developers/docs/devclass_docs/USB_Video_Class_1_5.zip
[3]: http://msdn.microsoft.com/en-gb/library/windows/desktop/dd757532(v=vs.85).aspx
Signed-off-by: William Manley <will@williammanley.net>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch drops driver specific wait_prepare() and wait_finish()
callbacks from vb2_ops and instead uses the the helpers
vb2_ops_wait_prepare/finish() provided by the vb2 core, the lock member
of the queue needs to be initalized to a mutex so that vb2 helpers
vb2_ops_wait_prepare/finish() can make use of it.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1) This is not allowed by the kernel coding style
2) Just configure your editor correctly
3) It's really ugly
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1rPM
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second set of media updates from Mauro Carvalho Chehab:
- Move drivers for really old legacy hardware to staging. Those are
using obsolete media kAPIs and are for hardware that nobody uses for
years. Simply not worth porting them to the new kAPIs. Of course,
if anyone pops up to fix, we can move them back from there
- While not too late, do some API fixups at the new colorspace API,
added for v3.19
- Some improvements for rcar_vin driver
- Some fixups at cx88 and vivid drivers
- Some Documentation fixups
* tag 'media/v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] bq/c-qcam, w9966, pms: move to staging in preparation for removal
[media] tlg2300: move to staging in preparation for removal
[media] vino/saa7191: move to staging in preparation for removal
[media] MAINTAINERS: vivi -> vivid
[media] cx88: remove leftover start_video_dma() call
[media] cx88: add missing alloc_ctx support
[media] v4l2-ioctl: WARN_ON if querycap didn't fill device_caps
[media] vivid: fix CROP_BOUNDS typo for video output
[media] DocBook media: update version number and document changes
[media] vivid.txt: document new controls
[media] DocBook media: add missing ycbcr_enc and quantization fields
[media] v4l2-mediabus.h: use two __u16 instead of two __u32
[media] rcar_vin: Fix interrupt enable in progressive
[media] rcar_vin: Enable VSYNC field toggle mode
[media] rcar_vin: Add scaling support
[media] rcar_vin: Add DT support for r8a7793 and r8a7794 SoCs
[media] rcar_vin: Add YUYV capture format support
This driver hasn't been tested in a long, long time. The company that made
this chip has gone bust many years ago and hardware using this chip is next
to impossible to find.
This driver needs to be converted to newer media frameworks but due to the
lack of hardware that's going to be impossible. Since cheap alternatives are
easily available, there is little point in keeping this driver alive.
In other words, this driver is a prime candidate for removal. If someone is
interested in working on this driver to prevent its removal, then please
contact the linux-media mailinglist.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
This patch is basically produced while testing a tool that
Joe Perches sent upstream sometime ago:
https://lkml.org/lkml/2014/7/11/794
I used it with those arguments:
$ reformat_with_checkpatch.sh drivers/media/usb/em28xx/em28xx*.[ch]
It actually produced 24 patches, with is too much, and showed
interesting things: gcc produced different codes on most of the
patches, even with just linespace changes. The total code data
remained the same on all cases I checked though.
Anyway, provided that we fold the resulting patches, this tool
seems useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Drivers that use dvb_attach can have just one exported symbol,
or they will cause compilation breakages depending on the
selected frontends.
As Jim reported:
drivers/built-in.o: In function `technisat_usb2_set_voltage':
technisat-usb2.c:(.text+0x3b4919): undefined reference to `stv090x_set_gpio'
make: *** [vmlinux] Error 1
That happens because, on his configuration, the configuration
is:
CONFIG_DVB_USB=y
CONFIG_DVB_STV090x=m
Luis proposed ar way to fix, but that would just force the
STV090x to be selected, even if one wants to use a device
with a different frontend.
Instead, let's do the right thing: move set_gpio to the
configuration structure and fill it during dvb_attach().
This way, the driver can still call it, and dvb_attach()
will load stv090x module only if the device really needs it.
Reported by: Jim Davis <jim.epost@gmail.com>
Cc: Luis Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove TechnoTrend CT2-4400 and CT2-4650 devices from cxusb.
They are supported by dvb-usb-dvbsky driver in PATCH 3/3.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Querycap shouldn't set the version field (the core does that for you),
but it should set the device_caps field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
According with Malcolm, the missing breaks are intentional.
So, let's revert commit d442b15fb4,
add some comments to document it and fix the two smatch warnings:
drivers/media/usb/dvb-usb-v2/lmedm04.c:828 lme_firmware_switch() warn: missing break? reassigning 'st->dvb_usb_lme2510_firmware'
drivers/media/usb/dvb-usb-v2/lmedm04.c:850 lme_firmware_switch() warn: missing break? reassigning 'st->dvb_usb_lme2510_firmware'
using a different strategy to avoid reassign values to
st->dvb_usb_lme2510_firmware.
Acked-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828 IR stop and poll routines continue to access device
while usb disconnect is in progress. There is small window
between device disconnect and usb interface is set to null.
This results in filling the log with several of the following
error messages. Fix it to detect device disconnect condition
and avoid device access.
Nov 20 18:58:02 anduin kernel: [ 102.949819] au0828: au0828_usb_disconnect()
Nov 20 18:58:02 anduin kernel: [ 102.950046] au0828: send_control_msg() Failed sending control message, error -71.
Nov 20 18:58:02 anduin kernel: [ 102.950052] au0828: send_control_msg() Failed sending control message, error -19.
Nov 20 18:58:02 anduin kernel: [ 102.950056] au0828: send_control_msg() Failed sending control message, error -19.
Nov 20 18:58:02 anduin kernel: [ 102.950061] au0828: send_control_msg() Failed sending control message, error -19.
Nov 20 18:58:02 anduin kernel: [ 102.950065] au0828: recv_control_msg() Failed receiving control message, error -19.
Nov 20 18:58:02 anduin kernel: [ 102.950069] au0828: recv_control_msg() Failed receiving control message, error -19.
Nov 20 18:58:02 anduin kernel: [ 102.950072] au0828: recv_control_msg() Failed receiving control message, error -19.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
GIT_AUTHOR_DATE=1416486805
The functions pvr2_hdw_destroy(), rc_unregister_device() and vfree() perform
also input parameter validation. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Terratec Cinergy T2 Stick HD [eb1a:8179] is a USB DVB-T/T2/C tuner that
contains following components:
* Empia EM28178 USB bridge
* Silicon Labs Si2168-A30 demodulator
* Silicon Labs Si2146-A10 tuner
I don't have the remote, so the RC_MAP is a best guess based on the pictures of
the remote controllers and other supported Terratec devices with a similar
remote.
[Antti: Resolved conflict caused by Leadtek VC100 patch]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
videobuf2 requires drivers to give back ownership of all queue buffers
in the stop_streaming operation, as well as in the start_streaming
operation in case of failure. Mark all queued buffers as done in the
error or queued state.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This brings the function name in line with the V4L2 API terminology and
allows removing the duplicate queue type check.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This brings the function name in line with the V4L2 API terminology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When releasing the file handle the driver calls the vb2_queue_release
which turns the stream off. There's thus no need to turn the stream off
explicitly beforehand.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To work propertly the videobuf2 core code needs to be in charge of
stream start/stop control. Implement the start_streaming and
stop_streaming vb2 operations and move video enable/disable code to
them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Factorize the container_of() call into an inline function and update
callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to make use of the vb2 queue start/stop_streaming operations
the video and queue enable/disable operations need to be split, as the
vb2 queue will need to enable and disable video instead of the other way
around.
Also move buffer queue disable outside of uvc_video_resume() to remove
all queue disable operations out of uvc_video.c.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver doesn't support interlaced video, set field to
V4L2_FIELD_NONE for all vb2 buffers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We've got a bug report at disconnecting a Webcam, where the kernel
spews warnings like below:
WARNING: CPU: 0 PID: 8385 at ../fs/sysfs/group.c:219 sysfs_remove_group+0x87/0x90()
sysfs group c0b2350c not found for kobject 'event3'
CPU: 0 PID: 8385 Comm: queue2:src Not tainted 3.16.2-1.gdcee397-default #1
Hardware name: ASUSTeK Computer INC. A7N8X-E/A7N8X-E, BIOS ASUS A7N8X-E Deluxe ACPI BIOS Rev 1013 11/12/2004
c08d0705 ddc75cbc c0718c5b ddc75ccc c024b654 c08c6d44 ddc75ce8 000020c1
c08d0705 000000db c03d1ec7 c03d1ec7 00000009 00000000 c0b2350c d62c9064
ddc75cd4 c024b6a3 00000009 ddc75ccc c08c6d44 ddc75ce8 ddc75cfc c03d1ec7
Call Trace:
[<c0205ba6>] try_stack_unwind+0x156/0x170
[<c02046f3>] dump_trace+0x53/0x180
[<c0205c06>] show_trace_log_lvl+0x46/0x50
[<c0204871>] show_stack_log_lvl+0x51/0xe0
[<c0205c67>] show_stack+0x27/0x50
[<c0718c5b>] dump_stack+0x3e/0x4e
[<c024b654>] warn_slowpath_common+0x84/0xa0
[<c024b6a3>] warn_slowpath_fmt+0x33/0x40
[<c03d1ec7>] sysfs_remove_group+0x87/0x90
[<c05a2c54>] device_del+0x34/0x180
[<c05e3989>] evdev_disconnect+0x19/0x50
[<c05e06fa>] __input_unregister_device+0x9a/0x140
[<c05e0845>] input_unregister_device+0x45/0x80
[<f854b1d6>] uvc_delete+0x26/0x110 [uvcvideo]
[<f84d66f8>] v4l2_device_release+0x98/0xc0 [videodev]
[<c05a25bb>] device_release+0x2b/0x90
[<c04ad8bf>] kobject_cleanup+0x6f/0x1a0
[<f84d5453>] v4l2_release+0x43/0x70 [videodev]
[<c0372f31>] __fput+0xb1/0x1b0
[<c02650c1>] task_work_run+0x91/0xb0
[<c024d845>] do_exit+0x265/0x910
[<c024df64>] do_group_exit+0x34/0xa0
[<c025a76f>] get_signal_to_deliver+0x17f/0x590
[<c0201b6a>] do_signal+0x3a/0x960
[<c02024f7>] do_notify_resume+0x67/0x90
[<c071ebb5>] work_notifysig+0x30/0x3b
[<b7739e60>] 0xb7739e5f
---[ end trace b1e56095a485b631 ]---
The cause is that uvc_status_cleanup() is called after usb_put_*() in
uvc_delete(). usb_put_*() removes the sysfs parent and eventually
removes the children recursively, so the later device_del() can't find
its sysfs. The fix is simply rearrange the call orders in
uvc_delete() so that the child is removed before the parent.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=897736
Reported-and-tested-by: Martin Pluskal <mpluskal@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds a quirk to force Y8 pixel format even if the camera reports
half-width YUYV.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When new parameters are added for si2168 driver, the parameters have to be explicitly defined for each device if the
si2168_config struct is not initialized to all zeros.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Load SDR sub-driver in order to support SDR for devices having
this tuner too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
That logic was duplicated from rtl2832_sdr.h in order to avoid hard
dependency for staging directory. rtl2832_sdr is moved to media, so
we could remove that code now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Better to rename tuner I2C to something which clearly says it is
for tuner as there is now multiple different I2C clients used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is RTL2832P devices having extra MN88473 demodulator. This
patch add support for such configuration. Logically MN88473 slave
demodulator is connected to RTL2832 master demodulator, both I2C
bus and TS input. RTL2832 is integrated to RTL2832U and RTL2832P
chips. Chip version RTL2832P has extra TS interface for connecting
slave demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is RTL2832P devices having extra MN88472 demodulator. This
patch add support for such configuration. Logically MN88472 slave
demodulator is connected to RTL2832 master demodulator, both I2C
bus and TS input. RTL2832 is integrated to RTL2832U and RTL2832P
chips. Chip version RTL2832P has extra TS interface for connecting
slave demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
length is the size of the buffer, not the payload. That's set using
vb2_set_plane_payload().
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Cc: <stable@vger.kernel.org> # for v3.15 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds "lgdt330x" device name i2c_devs array used for debugging
Signed-off-by: Wilson Michaels <thebitpit@earthlink.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to have subsytem agnostic media bus format definitions we've
moved media bus definition to include/uapi/linux/media-bus-format.h and
prefixed enum values with MEDIA_BUS_FMT instead of V4L2_MBUS_FMT.
Reference new definitions in all usb drivers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Enable integrated demod ADC only when demod is used. Keep integrated
demod ADC disabled when external demod is used. This fixes corrupted
stream in a case external demod was used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is wrong that sp2 device uses the i2c adapter from m88ds3103 return.
sp2 device sits on the same i2c bus with m88ds3103, not behind m88ds3103.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
qlock spinlock controls access to buf_list and sequence.
qlock spinlock should not be locked during a copy to video buffers, an
operation that may sleep.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
stk1160-v4l.c:478:49: warning: incorrect type in argument 3 (different base types)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kbuild test robot:
drivers/media/usb/cx231xx/cx231xx-audio.c:445:16-20: ERROR: dev is NULL but dereferenced.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unfortunately, on devices that have multiple interfaces, udev->dev
points to the parent device (usb) instead of the cx231xx specific one.
Due to that the logs don't look too nice, as they'll print messages
as if they were produced by USB core:
usb-1-2: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Instead of using the name of the parent device, let's use the name
of the first cx231xx interface for all cx231xx sub-modules.
With this path, the logs will be nicer:
cx231xx 1-2:1.1: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't need to show when it starts or stops. Just print lines
when devices are found.
After the changes, the output for i2c scan will be like:
usb 1-2: i2c scan: found device @ port 0 addr 0x40 [???]
usb 1-2: i2c scan: found device @ port 0 addr 0x60 [colibri]
usb 1-2: i2c scan: found device @ port 0 addr 0x88 [hammerhead]
usb 1-2: i2c scan: found device @ port 0 addr 0x98 [???]
usb 1-2: i2c scan: found device @ port 3 addr 0xa0 [eeprom]
usb 1-2: i2c scan: found device @ port 2 addr 0x60 [colibri]
usb 1-2: i2c scan: found device @ port 2 addr 0xc0 [tuner]
usb 1-2: i2c scan: found device @ port 4 addr 0x20 [demod]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we're using dev_foo, the logs become like:
usb 1-2: DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
usb 1-2: Successfully loaded cx231xx-dvb
cx231xx: Cx231xx dvb Extension initialized
It is not clear, by the logs, that usb 1-2 name is an alias for
cx231xx. So, we also need to use dvb_info() at extension load/unload.
After the patch, it will print:
usb 1-2: Cx231xx dvb Extension initialized
With is coherent with the other logs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several places at cx231xx that uses printk without
any special reason. Change all of them to use dev_foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Mauro Carvalho Chehab
Hans Verkuil
Christian Dale
Dimitris Lampridis
David Howells
Luis de Bethencourt
Benjamin Larsson
Hans Verkuil
Alexey Khoroshilov
Antti Palosaari
Olli Salonen
Guennadi Liakhovetski
Ezequiel Garcia
Laurent Pinchart
Gilles Risch
Wei Yongjun
Shuah Khan
Lad, Prabhakar
Randy Dunlap
Markus Elfring
Nicholas Mc Guire
Rafael Lourenço de Lima Chehab
Malcolm Priestley
Arnd Bergmann
Nicholas Mc Guire
Luca Bonissi
Hans de Goede
Joe Howse
Antonio Ospite
John McMaster
Fabian Frederick
Aviv Greenberg
Rickard Strandqvist
Julia Lawall
Linus Torvalds
Jonathan McDowell
Russell King
William Manley
Nibble Max
CrazyCat
Takashi Iwai
Philipp Zabel
sensoray-dev
Wilson Michaels
Boris BREZILLON