The per-cpu counter for init_net is prepared in core_initcall.
The patch 7d720c3e ("percpu: add __percpu sparse annotations to net")
and d6d9ca0fe ("net: this_cpu_xxx conversions") optimize the
routines. Then remove the old counter.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the TIPC RPS dissector is based only on the incoming packets'
source node address, hence steering all traffic from a node to the same
core. We have seen that this makes the links vulnerable to starvation
and unnecessary resets when we turn down the link tolerance to very low
values.
To reduce the risk of this happening, we exempt probe and probe replies
packets from the convergence to one core per source node. Instead, we do
the opposite, - we try to diverge those packets across as many cores as
possible, by randomizing the flow selector key.
To make such packets identifiable to the dissector, we add a new
'is_keepalive' bit to word 0 of the LINK_PROTOCOL header. This bit is
set both for PROBE and PROBE_REPLY messages, and only for those.
It should be noted that these packets are not part of any flow anyway,
and only constitute a minuscule fraction of all packets sent across a
link. Hence, there is no risk that this will affect overall performance.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we want to gradually implement per netns sysctl_rmem and sysctl_wmem
on per protocol basis, add two new fields in struct proto,
and two new helpers : sk_get_wmem0() and sk_get_rmem0()
First user will be TCP. Then UDP and SCTP can be easily converted,
while DECNET probably wont get this support.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Timestamps in pktgen are currently retrieved using the deprecated
do_gettimeofday() function that wraps its signed 32-bit seconds in 2038
(on 32-bit architectures) and requires a division operation to calculate
microseconds.
The pktgen header is also defined with the same limitations, hardcoding
to a 32-bit seconds field that can be interpreted as unsigned to produce
times that only wrap in 2106. Whatever code reads the timestamps should
be aware of that problem in general, but probably doesn't care too
much as we are mostly interested in the time passing between packets,
and that is correctly represented.
Using 64-bit nanoseconds would be cheaper and good for 584 years. Using
monotonic times would also make this unambiguous by avoiding the overflow,
but would make it harder to correlate to the times with those on remote
machines. Either approach would require adding a new runtime flag and
implementing the same thing on the remote side, which we probably don't
want to do unless someone sees it as a real problem. Also, this should
be coordinated with other pktgen implementations and might need a new
magic number.
For the moment, I'm documenting the overflow in the source code, and
changing the implementation over to an open-coded ktime_get_real_ts64()
plus division, so we don't have to look at it again while scanning for
deprecated time interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size for IFLA_IF_NETNSID is missing from the size calculation
because the proceeding semicolon was not removed. Fix this by removing
the semicolon.
Detected by CoverityScan, CID#1461135 ("Structurally dead code")
Fixes: 79e1ad148c ("rtnetlink: use netnsid to query interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to the ability to load a program for a specific device,
running verifier twice is no longer needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the netdev pointer to bpf_prog_get_type(). This way
BPF code can decide whether the device matches what the
code was loaded/translated for.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an application gets netnsid from the kernel (for example as
the result of RTM_GETLINK call on one end of the veth pair), it's not much
useful. There's no reliable way to get to the netns fd from the netnsid, nor
does any kernel API accept netnsid.
Extend the RTM_GETLINK call to also accept netnsid. It will operate on the
netns with the given netnsid in such case. Of course, the calling process
needs to have enough capabilities in the target name space; for now, require
CAP_NET_ADMIN. This can be relaxed in the future.
To signal to the calling process that the kernel understood the new
IFLA_IF_NETNSID attribute in the query, it will include it in the response.
This is needed to detect older kernels, as they will just ignore
IFLA_IF_NETNSID and query in the current name space.
This patch implemetns IFLA_IF_NETNSID only for get and dump. For set
operations, this can be extended later.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen accidentally used IN6_ADDR_HSIZE, instead of using the size of an
IPv6 address.
Since IN6_ADDR_HSIZE recently was increased from 16 to 256, this old
bug is hitting us.
Fixes: 3f27fb2321 ("ipv6: addrconf: add per netns perturbation in inet6_addr_hash()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ipvs in two different network namespace at the same host, and one
ipvs transport network traffic to the other network namespace ipvs.
'ipvs_property' flag will make the second ipvs take no effect. So we should
clear 'ipvs_property' when SKB network namespace changed.
Fixes: 621e84d6f3 ("dev: introduce skb_scrub_packet()")
Signed-off-by: Ye Yin <hustcat@gmail.com>
Signed-off-by: Wei Zhou <chouryzhou@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In sch_handle_egress and sch_handle_ingress tp->q is used only in order
to update stats. So stats and filter list are the only things that are
needed in clsact qdisc fastpath processing. Introduce new mini_Qdisc
struct to hold those items. Also, introduce a helper to swap the
mini_Qdisc structures in case filter list head changes.
This removes need for tp->q usage without added overhead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_getsockopt bpf call sets the ret variable to zero and
never changes it. What's worse in case CONFIG_INET is
not selected the variable is completely unused generating
a warning.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the patch 'rtnetlink: bring NETDEV_CHANGELOWERSTATE event
process back to rtnetlink_event', bond_lower_state_changed would
generate NETDEV_CHANGEUPPER event which would send a notification
to userspace in rtnetlink_event.
There's no need to call rtmsg_ifinfo to send the notification
any more. So this patch is to remove it from these places after
bond_lower_state_changed.
Besides, after this, rtmsg_ifinfo is not needed to be exported.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to bring NETDEV_CHANGELOWERSTATE event process back
to rtnetlink_event so that bonding could use it instead of calling
rtmsg_ifinfo to send a notification to userspace after netdev lower
state is changed in the later patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New tracepoint trace_tcp_send_reset is added and called from
tcp_v4_send_reset(), tcp_v6_send_reset() and tcp_send_active_reset().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BUG_ON instead of if condition followed by BUG in do_setlink.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for helper function bpf_getsockops to socket_ops BPF
programs. This patch only supports TCP_CONGESTION.
Signed-off-by: Vlad Vysotsky <vlad@cs.ucla.edu>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9cab88726929605 ("net: ethtool: Add back transceiver type")
restores the transceiver type to struct ethtool_link_settings and
convert_link_ksettings_to_legacy_settings() but forgets to remove the
error check for the same in convert_legacy_settings_to_link_ksettings().
This prevents older versions of ethtool to change link settings.
# ethtool --version
ethtool version 3.16
# ethtool -s eth0 autoneg on speed 100 duplex full
Cannot set new settings: Invalid argument
not setting speed
not setting duplex
not setting autoneg
While newer versions of ethtool works.
# ethtool --version
ethtool version 4.10
# ethtool -s eth0 autoneg on speed 100 duplex full
[ 57.703268] sh-eth ee700000.ethernet eth0: Link is Down
[ 59.618227] sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Fixes: 19cab88726 ("net: ethtool: Add back transceiver type")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Renjith R V <renjith.rv@quest-global.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller stumbled upon a way to trigger
WARNING: CPU: 1 PID: 13881 at net/core/sock_reuseport.c:41
reuseport_alloc+0x306/0x3b0 net/core/sock_reuseport.c:39
There are two initialization paths for the sock_reuseport structure in a
socket: Through the udp/tcp bind paths of SO_REUSEPORT sockets or through
SO_ATTACH_REUSEPORT_[CE]BPF before bind. The existing implementation
assumedthat the socket lock protected both of these paths when it actually
only protects the SO_ATTACH_REUSEPORT path. Syzkaller triggered this
double allocation by running these paths concurrently.
This patch moves the check for double allocation into the reuseport_alloc
function which is protected by a global spin lock.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller hits WARN_ON(sk->sk_wmem_queued) in sk_stream_kill_queues
after triggering an EFAULT in __zerocopy_sg_from_iter.
On this error, skb_zerocopy_stream_iter resets the skb to its state
before the operation with __pskb_trim. It cannot kfree_skb like
datagram callers, as the skb may have data from a previous send call.
__pskb_trim calls skb_condense for unowned skbs, which adjusts their
truesize. These tcp skbuffs are owned and their truesize must add up
to sk_wmem_queued. But they match because their skb->sk is NULL until
tcp_transmit_skb.
Temporarily set skb->sk when calling __pskb_trim to signal that the
skbuffs are owned and avoid the skb_condense path.
Fixes: 52267790ef ("sock: add MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->mark field is a union with reserved_tailroom which is used
in the TCP code paths from stream memory allocation. Allowing SK_SKB
programs to set this field creates a conflict with future code
optimizations, such as "gifting" the skb to the egress path instead
of creating a new skb and doing a memcpy.
Because we do not have a released version of SK_SKB yet lets just
remove it for now. A more appropriate scratch pad to use at the
socket layer is dev_scratch, but lets add that in future kernels
when needed.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-17
This series contains updates to i40e and ethtool.
Alan provides most of the changes in this series which are mainly fixes
and cleanups. Renamed the ethtool "cmd" variable to "ks", since the new
ethtool API passes us ksettings structs instead of command structs.
Cleaned up an ifdef that was not accomplishing anything. Added function
header comments to provide better documentation. Fixed two issues in
i40e_get_link_ksettings(), by calling
ethtool_link_ksettings_zero_link_mode() to ensure the advertising and
link masks are cleared before we start setting bits. Cleaned up and fixed
code comments which were incorrect. Separated the setting of autoneg in
i40e_phy_types_to_ethtool() into its own conditional to clarify what PHYs
support and advertise autoneg, and makes it easier to add new PHY types in
the future. Added ethtool functionality to intersect two link masks
together to find the common ground between them. Overhauled i40e to
ensure that the new ethtool API macros are being used, instead of the
old ones. Fixed the usage of unsigned 64-bit division which is not
supported on all architectures.
Sudheer adds support for 25G Active Optical Cables (AOC) and Active Copper
Cables (ACC) PHY types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we are now doing strict checking of what offloads
may access, make sure skb->len is on that list.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the fact that verifier ops are now separate from program
ops to define a separate set of callbacks for verification of
already translated programs.
Since we expect the analyzer ops to be defined only for
a small subset of all program types initialize their array
by hand (don't use linux/bpf_types.h).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bpf_verifier_ops contains both verifier ops and operations
used later during program's lifetime (test_run). Split the runtime
ops into a different structure.
BPF_PROG_TYPE() will now append ## _prog_ops or ## _verifier_ops
to the names.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly for all users of sk_timer.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: linzhang <xiaolou4617@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-x25@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core sk_timer initializer can provide the common .data assignment
instead of it being set separately in users.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linzhang <xiaolou4617@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-x25@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes cpumap functional, by adding SKB allocation and
invoking the network stack on the dequeuing CPU.
For constructing the SKB on the remote CPU, the xdp_buff in converted
into a struct xdp_pkt, and it mapped into the top headroom of the
packet, to avoid allocating separate mem. For now, struct xdp_pkt is
just a cpumap internal data structure, with info carried between
enqueue to dequeue.
If a driver doesn't have enough headroom it is simply dropped, with
return code -EOVERFLOW. This will be picked up the xdp tracepoint
infrastructure, to allow users to catch this.
V2: take into account xdp->data_meta
V4:
- Drop busypoll tricks, keeping it more simple.
- Skip RPS and Generic-XDP-recursive-reinjection, suggested by Alexei
V5: correct RCU read protection around __netif_receive_skb_core.
V6: Setting TASK_RUNNING vs TASK_INTERRUPTIBLE based on talk with Rik van Riel
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch connects cpumap to the xdp_do_redirect_map infrastructure.
Still no SKB allocation are done yet. The XDP frames are transferred
to the other CPU, but they are simply refcnt decremented on the remote
CPU. This served as a good benchmark for measuring the overhead of
remote refcnt decrement. If driver page recycle cache is not
efficient then this, exposes a bottleneck in the page allocator.
A shout-out to MST's ptr_ring, which is the secret behind is being so
efficient to transfer memory pointers between CPUs, without constantly
bouncing cache-lines between CPUs.
V3: Handle !CONFIG_BPF_SYSCALL pointed out by kbuild test robot.
V4: Make Generic-XDP aware of cpumap type, but don't allow redirect yet,
as implementation require a separate upstream discussion.
V5:
- Fix a maybe-uninitialized pointed out by kbuild test robot.
- Restrict bpf-prog side access to cpumap, open when use-cases appear
- Implement cpu_map_enqueue() as a more simple void pointer enqueue
V6:
- Allow cpumap type for usage in helper bpf_redirect_map,
general bpf-prog side restriction moved to earlier patch.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function provides a way to intersect two link masks together to
find the common ground between them. For example in i40e, the driver
first generates link masks for what is supported by the PHY type. The
driver then gets the link masks for what the NVM supports. The
resulting intersection between them yields what can truly be supported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 32302902ff ("mqprio: Reserve last 32 classid values for HW
traffic classes and misc IDs") sch_mqprio started using netdev_txq_to_tc
to find the correct tc instead of dev->tc_to_txq[]
However, when mqprio is compiled as a module, it cannot resolve the
symbol, leading to this error:
ERROR: "netdev_txq_to_tc" [net/sched/sch_mqprio.ko] undefined!
This adds an EXPORT_SYMBOL() since the other user in the kernel
(netif_set_xps_queue) is also EXPORT_SYMBOL() (and not _GPL) or in a
sysfs-callback.
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Henrik Austad <haustad@cisco.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl af_ops currently rely on rtnl mutex: unregister (called from module
exit functions) takes the rtnl mutex and all users that do af_ops lookup
also take the rtnl mutex. IOW, parallel rmmod will block until doit()
callback is done.
As none of the af_ops implementation sleep we can use rcu instead.
doit functions that need the af_ops can now use rcu instead of the
rtnl mutex provided the mutex isn't needed for other reasons.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
next patch will rcu-ify rtnl af_ops, i.e. allow af_ops
lookup and function calls with rcu read lock held instead
of rtnl mutex.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing dev tx_queue_len via netlink or net-sysfs,
a NETDEV_CHANGE_TX_QUEUE_LEN event notification will be
called.
But dev_ioctl missed this event notification, which could
cause no userspace notification would be sent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_IFALIAS is defined as NLA_STRING. It means that the minimal length of
the attribute is 1 ("\0"). However, to remove an alias, the attribute
length must be 0 (see dev_set_alias()).
Let's define the type to NLA_BINARY to allow 0-length string, so that the
alias can be removed.
Example:
$ ip l s dummy0 alias foo
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
alias foo
Before the patch:
$ ip l s dummy0 alias ""
RTNETLINK answers: Numerical result out of range
After the patch:
$ ip l s dummy0 alias ""
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
CC: Oliver Hartkopp <oliver@hartkopp.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
Fixes: 96ca4a2cc1 ("net: remove ifalias on empty given alias")
Reported-by: Julien FLoret <julien.floret@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_CHANGE_TX_QUEUE_LEN event process in rtnetlink_event would
send a notification for userspace and tx_queue_len's setting in
do_setlink would trigger NETDEV_CHANGE_TX_QUEUE_LEN.
So it shouldn't set DO_SETLINK_NOTIFY status for this change to
send a notification any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check 'status & DO_SETLINK_NOTIFY' in do_setlink doesn't really
work after status & DO_SETLINK_MODIFIED, as:
DO_SETLINK_MODIFIED 0x1
DO_SETLINK_NOTIFY 0x3
Considering that notifications are suppposed to be sent only when
status have the flag DO_SETLINK_NOTIFY, the right check would be:
(status & DO_SETLINK_NOTIFY) == DO_SETLINK_NOTIFY
This would avoid lots of duplicated notifications when setting some
properties of a link.
Fixes: ba9989069f ("rtnl/do_setlink(): notify when a netdev is modified")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tonghao Zhang
Jon Maloy
Eric Dumazet
David S. Miller
Arnd Bergmann
Colin Ian King
Jakub Kicinski
Jiri Benc
Ye Yin
Jiri Pirko
Linus Torvalds
Greg Kroah-Hartman
David Ahern
John Fastabend
Xin Long
Song Liu
Gustavo A. R. Silva
Lawrence Brakmo
Niklas Söderlund
Craig Gallek
Willem de Bruijn
Kees Cook
Jesper Dangaard Brouer
Alan Brady
Henrik Austad
Florian Westphal
Cong Wang
Nicolas Dichtel