Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):
* Fix the problem by adding missing struct ata_port_info to artop_init_one().
* Use the right naming (s/626/628/).
* Bump driver version.
Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c-s3c2410: Build fix
i2c/menelaus: Build fix
i2c-mv64xxx: Reinitialize hw and driver on I2C bus hang
i2c-mpc: Don't disable I2C module on stop condition
i2c-iop3xx: Set I2C_CLASS_HWMON to adapter class
i2c/isp1301_omap: Build fixes, whitespace
i2c-mpc: Pass correct dev_id to free_irq on error path
i2c-i801: Typo: erroneous
Fixup the include files after the arch moves that
where included in 2.6.23.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Under certain conditions, the mv64xxx I2C bus can hang preventing
further operation. To make the driver more robust, we now reset
the I2C hardware and the driver state machine when such hangs are
detected.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Disabling module on stop doesn't work on some CPUs (ie. mpc8241,
as reported by Guennadi Liakhovetski), so remove that.
Disable I2C module on errors/interrupts to prevent it from
locking up on mpc5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In order to be able to use sensors on the IOP3xx SoCs, one needs to set
the adapter class to I2C_CLASS_HWMON.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Build fixes for isp1301_omap driver. I think an earlier version
of this must have gotten lost somewhere, or maybe it only went
into the Linux-OMAP tree.
Also, some whitespace fixes to bring this more into sync with the
version of this found in the Linux-OMAP tree. (That version has
updates for the OTG controller on the OMAP 1710 which break that
functionality on OMAP 161x boards like the H2, so merging all of
it is not currently an option.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPVS]: Use IP_VS_WAIT_WHILE when encessary.
[NET]: Share correct feature code between bridging and bonding
[ATM] drivers/atm/iphase.c: mostly kmalloc + memset conversion to kzalloc
[IRDA] irda-usb.c: mostly kmalloc + memset conversion to k[cz]alloc
[WAN] drivers/net/wan/hdlc_fr.c: kmalloc + memset conversion to kzalloc
[DCCP]: fix memory leak and clean up style - dccp_feat_empty_confirm()
[DCCP]: fix theoretical ccids_{read,write}_lock() race
[XFRM]: Clean up duplicate includes in net/xfrm/
[TIPC]: Clean up duplicate includes in net/tipc/
[SUNRPC]: Clean up duplicate includes in net/sunrpc/
[PKT_SCHED]: Clean up duplicate includes in net/sched/
[IPV6]: Clean up duplicate includes in net/ipv6/
[IPV4]: Clean up duplicate includes in net/ipv4/
[ATM]: Clean up duplicate includes in net/atm/
[ATM]: Clean up duplicate includes in drivers/atm/
[IPCONFIG]: ip_auto_config fix
[ATM]: fore200e_param_bs_queue() must be __devinit
This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
http://bugzilla.kernel.org/show_bug.cgi?id=8797 shows that the
bonding driver may produce bogus combinations of the checksum
flags and SG/TSO.
For example, if you bond devices with NETIF_F_HW_CSUM and
NETIF_F_IP_CSUM you'll end up with a bonding device that
has neither flag set. If both have TSO then this produces
an illegal combination.
The bridge device on the other hand has the correct code to
deal with this.
In fact, the same code can be used for both. So this patch
moves that logic into net/core/dev.c and uses it for both
bonding and bridging.
In the process I've made small adjustments such as only
setting GSO_ROBUST if at least one constituent device
supports it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up duplicate includes in
drivers/atm/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
WARNING: drivers/built-in.o(.text+0x6203bb): Section mismatch: reference to .init.text:fore200e_param_bs_queue (between 'fore200e_initialize' and 'fore200e_monitor_putc')
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_tx_bug_gc can free the skb before we use it, so make sure we don't.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A special sequence of ifconfig up/down and plug/unplug the cable can break
the duplex configuration of the driver.
Setting
vp->mii.full_duplex = vp->full_duplex
in vortex_up should fix this.
Addresses Bug 8575 3c59x duplex configuration broken
http://bugzilla.kernel.org/show_bug.cgi?id=8575
Cc: Martin Buck <mb-tmp-ohtmvyyn.xreary.bet@gromit.dyndns.org>
Signed-off-by: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When a detailed netdev error is counted, we also must account for it in the
aggregated error count.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=8106
Cc: Tim Hockin <thockin@hockin.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Chongfeng Hu <loveminix@yahoo.com.cn>
Cc: Natalie Protasevich <protasnb@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ax88796.c: In function `ax_probe':
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 4)
drivers/net/ax88796.c:825: warning: size_t format, different type arg (arg 5)
resource_size_t isn't size_t.
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the pause counter to avoid a needless device reset, and
print a message telling the admin that our link partner is
flow controlling us down to 0 pkts/sec.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to disable the rx_copybreak feature on hardware architectures that
don't allow unaligned DMA access.
#ifdef code taken from tulip_core.c. Problem pointed out by Ivan
Kokshaysky.
Signed-off-by: Dustin Marquess <jailbird@alcatraz.fdf.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use DMI to:
1. enable polling (BIOS thermal events are broken)
2. disable active trip points (BIOS fan control is broken)
3. disable passive trip point (BIOS hard-codes it too low)
The actual temperature reading does work,
and with the aid of polling, the critical
trip point should work too.
http://bugzilla.kernel.org/show_bug.cgi?id=8842
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.act=-1 disables all active trip points
in all ACPI thermal zones.
thermal.act=C, where C > 0, overrides all lowest temperature
active trip points in all thermal zones to C degrees Celsius.
Raising this trip-point may allow you to keep your system silent
up to a higher temperature. However, it will not allow you to
raise the lowest temperature trip point above the next higher
trip point (if there is one). Lowering this trip point may
kick in the fan sooner.
Note that overriding this trip-point will disable any BIOS attempts
to implement hysteresis around the lowest temperature trip point.
This may result in the fan starting and stopping frequently
if temperature frequently crosses C.
WARNING: raising trip points above the manufacturer's defaults
may cause the system to run at higher temperature and shorten
its life.
Signed-off-by: Len Brown <len.brown@intel.com>
thermal.nocrt=1 disables actions on _CRT and _HOT
ACPI thermal zone trip-points. They will be marked
as <disabled> in /proc/acpi/thermal_zone/*/trip_points.
There are two cases where this option is used:
1. Debugging a hot system crossing valid trip point.
If your system fan is spinning at full speed,
be sure that the vent is not clogged with dust.
Many laptops have very fine thermal fins that are easily blocked.
Check that the processor fan-sink is properly seated,
has the proper thermal grease, and is really spinning.
Check for fan related options in BIOS SETUP.
Sometimes there is a performance vs quiet option.
Defaults are generally the most conservative.
If your fan is not spinning, yet /proc/acpi/fan/
has files in it, please file a Linux/ACPI bug.
WARNING: you risk shortening the lifetime of your
hardware if you use this parameter on a hot system.
Note that this refers to all system components,
including the disk drive.
2. Working around a cool system crossing critical
trip point due to erroneous temperature reading.
Try again with CONFIG_HWMON=n
There is known potential for conflict between the
the hwmon sub-system and the ACPI BIOS.
If this fixes it, notify lm-sensors@lm-sensors.org
and linux-acpi@vger.kernel.org
Otherwise, file a Linux/ACPI bug, or notify
just linux-acpi@vger.kernel.org.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.psv=-1" disables passive trip points
for all ACPI thermal zones.
"thermal.psv=C", where 'C' is degrees Celsius,
overrides all existing passive trip points
for all ACPI thermal zones.
thermal.psv is checked at module load time,
and in response to trip-point change events.
Note that if the system does not deliver thermal zone
temperature change events near the new trip-point,
then it will not be noticed. To force your custom
trip point to be noticed, you may need to enable polling:
eg. thermal.tzp=3000 invokes polling every 5 minutes.
Note that once passive thermal throttling is invoked,
it has its own internal Thermal Sampling Period (_TSP),
that is unrelated to _TZP.
WARNING: disabling or raising a thermal trip point
may result in increased running temperature and
shorter hardware lifetime on some systems.
Signed-off-by: Len Brown <len.brown@intel.com>
Thermal Zone Polling frequency (_TZP) is an optional ACPI object
recommending the rate that the OS should poll the associated thermal zone.
If _TZP is 0, no polling should be used.
If _TZP is non-zero, then the platform recommends that
the OS poll the thermal zone at the specified rate.
The minimum period is 30 seconds.
The maximum period is 5 minutes.
(note _TZP and thermal.tzp units are in deci-seconds,
so _TZP = 300 corresponds to 30 seconds)
If _TZP is not present, ACPI 3.0b recommends that the
thermal zone be polled at an "OS provided default frequency".
However, common industry practice is:
1. The BIOS never specifies any _TZP
2. High volume OS's from this century never poll any thermal zones
Ie. The OS depends on the platform's ability to
provoke thermal events when necessary, and
the "OS provided default frequency" is "never":-)
There is a proposal that ACPI 4.0 be updated to reflect
common industry practice -- ie. no _TZP, no polling.
The Linux kernel already follows this practice --
thermal zones are not polled unless _TZP is present and non-zero.
But thermal zone polling is useful as a workaround for systems
which have ACPI thermal control, but have an issue preventing
thermal events. Indeed, some Linux distributions still
set a non-zero thermal polling frequency for this reason.
But rather than ask the user to write a polling frequency
into all the /proc/acpi/thermal_zone/*/polling_frequency
files, here we simply document and expose the already
existing module parameter to do the same at system level,
to simplify debugging those broken platforms.
Note that thermal.tzp is a module-load time parameter only.
Signed-off-by: Len Brown <len.brown@intel.com>
"thermal.off=1" disables all ACPI thermal support at boot time.
CONFIG_ACPI_THERMAL=n can do this at build time.
"# rmmod thermal" can do this at run time,
as long as thermal is built as a module.
WARNING: On some systems, disabling ACPI thermal support
will cause the system to run hotter and reduce the
lifetime of the hardware.
Signed-off-by: Len Brown <len.brown@intel.com>
Make the needlessly global "acpi_event_seqnum" static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Send key=value pair along with the uevent instead of a plain value so that
userspace (udev) can handle it like common environment variables.
Signed-off-by: Holger Macht <hmacht@suse.de>
Acked-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There must not be a new-line character in the uevent. Otherwise, udev gets
confused. Thanks to Kay Sievers for pointing it out.
Signed-off-by: Stephan Berberig <s.berberig@arcor.de>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] monwriter: Serialization bug for multithreaded applications.
[S390] vmur: diag14 only works with buffers below 2GB
[S390] vmur: add "top of queue" sanity check for reader open
[S390] vmur: reject open on z/VM reader files with status HOLD
[S390] vmur: use DECLARE_COMPLETION_ONSTACK to keep lockdep happy
[S390] vmur: allocate single record buffers instead of one big data buffer
[S390] remove DEFAULT_MIGRATION_COST
[S390] qdio: make sure data structures are correctly aligned.
[S390] hypfs: implement show_options
[S390] cio: avoid memory leak on error in css_alloc_subchannel().
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
BLOCK: Hide the contents of linux/bio.h if CONFIG_BLOCK=n
sysace: HDIO_GETGEO has it's own method for ages
drivers/block/cpqarray.c: better error handling and kmalloc + memset conversion to k[cz]alloc
drivers/block/cciss.c: kmalloc + memset conversion to kzalloc
Clean up duplicate includes in drivers/block/
Fix remap handling by blktrace
[PATCH] remove mm/filemap.c:file_send_actor()
Bartlomiej Zolnierkiewicz
Tejun Heo
Alan Cox
Jeff Garzik
Linus Torvalds
Ben Dooks
David Brownell
Dale Farnsworth
Domen Puncer
Arnaud Patard
Scott Wood
Jean Delvare
Auke Kok
Herbert Xu
Mariusz Kozlowski
Jesper Juhl
Adrian Bunk
Jeremy Fitzhardinge
Steffen Klassert
Andrew Morton
Brice Goglin
Dustin Marquess
Alexey Starikovskiy
Len Brown
Alexey Starikovskiy
Holger Macht
Stephan Berberig