The SME state machine in cfg80211 uses the SSID stored
in struct wireless_dev internally, but fails to clear
it in multiple places (when giving up on a connection
attempt and when disconnecting). This doesn't matter to
the SME state machine, but does matter for IBSS. Thus,
in those cases, clear the SSID to avoid messing up the
IBSS state machine.
Reported-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default of 500ms is pretty high, and leads
to the device being awake at least 50% of the
time under such light traffic conditions as a
simple 1 second interval ping. Reduce to just
100ms -- it should have a similar effect while
providing a better sleep time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.
Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We change regulatory code to be protected by its own regulatory
mutex and alleviate cfg80211_mutex to only be used to protect
cfg80211_rdev_list, the registered device list.
By doing this we will be able to work on regulatory core components
without having to have hog up the cfg80211_mutex. An example here is
we no longer need to use the cfg80211_mutex during driver specific
wiphy_apply_custom_regulatory(). We also no longer need it for the
the country IE regulatory hint; by doing so we end up curing this
new lockdep warning:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #12
-------------------------------------------------------
phy1/1709 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa00af852>] regulatory_hint_11d+0x32/0x3f0 [cfg80211]
but task is already holding lock:
(&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&ifmgd->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa0141bb8>] ieee80211_mgd_auth+0x108/0x1f0 [mac80211]
[<ffffffffa0148563>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffa00bc3a1>] __cfg80211_mlme_auth+0x1b1/0x2a0 [cfg80211]
[<ffffffffa00bc516>] cfg80211_mlme_auth+0x86/0xc0 [cfg80211]
[<ffffffffa00b368d>] nl80211_authenticate+0x21d/0x230 [cfg80211]
[<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
[<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
[<ffffffff814169d9>] genl_rcv+0x29/0x40
[<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
[<ffffffff81416514>] netlink_sendmsg+0x214/0x300
[<ffffffff813e4407>] sock_sendmsg+0x107/0x130
[<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
-> #2 (&wdev->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa00ab304>] cfg80211_netdev_notifier_call+0x1a4/0x390 [cfg80211]
[<ffffffff814f3dff>] notifier_call_chain+0x3f/0x80
[<ffffffff81075a91>] raw_notifier_call_chain+0x11/0x20
[<ffffffff813f665a>] dev_open+0x10a/0x120
[<ffffffff813f59bd>] dev_change_flags+0x9d/0x1e0
[<ffffffff8144eb6e>] devinet_ioctl+0x6fe/0x760
[<ffffffff81450204>] inet_ioctl+0x94/0xc0
[<ffffffff813e25fa>] sock_ioctl+0x6a/0x290
[<ffffffff8111e911>] vfs_ioctl+0x31/0xa0
[<ffffffff8111ea9a>] do_vfs_ioctl+0x8a/0x5c0
[<ffffffff8111f069>] sys_ioctl+0x99/0xa0
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
-> #1 (&rdev->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa00ac4d0>] cfg80211_get_dev_from_ifindex+0x60/0x90 [cfg80211]
[<ffffffffa00b21ff>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa00b51eb>] nl80211_set_interface+0x3b/0x260 [cfg80211]
[<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
[<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
[<ffffffff814169d9>] genl_rcv+0x29/0x40
[<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
[<ffffffff81416514>] netlink_sendmsg+0x214/0x300
[<ffffffff813e4407>] sock_sendmsg+0x107/0x130
[<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
other info that might help us debug this:
3 locks held by phy1/1709:
#0: ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
#1: (&ifmgd->work){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
#2: (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the country IE hint code by just bailing out if
a previous country IE has been issued. We currently just trust
the first AP we connect to on any card. The idea was to perform
conflict resolution within this routine but since we can no longer
iterate over the registered device list here we leave conflict
resolution to be dealt with at a later time on the workqueue.
This code has no functional changes other than saving us an
interation over the registered device list when a second card
is connected, or you unplug and connect the same one, and a
country IE is received. This would have been done upon every
beacon received.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional changes.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It's possible to get the NETDEV_UNREGISTER callback multiple
times (see net/core/dev.c:netdev_wait_allrefs) and this will
completely mess up our cleanup code. To avoid that, clean up
only when the interface is still on the wiphy interface list
from which it's removed on the first NETDEV_UNREGISTER call.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a userspace SME is active, we're currently not
keeping track of the BSS properly for reporting the
current link and for internal use. Additionally, it
looks like there is a possible BSS leak in that the
BSS never gets removed from auth_bsses[]. To fix it,
pass the BSS struct to __cfg80211_connect_result in
this case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regression was added through patch a4ed90d6:
"cfg80211: respect API on orig_flags on channel for beacon hint"
We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.
By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.
Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.
We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.
This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.
I tested this with a world roaming ath5k card.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These pointers can be NULL, the is_mesh() case isn't
ever hit in the current kernel, but cmp_ies() can be
hit under certain conditions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finally! This is what you've all been waiting for!
This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!
RIP wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have handlers IWESSID for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have IWAP handlers for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to disassociate while not associated,
the kernel would crash rather than refusing the
operation, fix this;
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni and Maxim reported an oops when using wpa_supplicant -Dnl80211,
which seems to be due to random data being contained in the crypto
settings for the assoc() command. This seems to be due to the missing
memset here, so add it -- it's certainly missing but I'm not 100%
certain that it will fix the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported this lockdep complaint, that he had also
reported earlier but when trying to analyse I had been
locking at the wrong code, and never saw the problem:
(slightly abridged)
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #6
-------------------------------------------------------
wpa_supplicant/3799 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff81400ff2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffff81400ff2>] rtnl_lock+0x12/0x20
[<ffffffffa009f6a5>] nl80211_send_reg_change_event+0x1f5/0x2a0 [cfg80211]
[<ffffffffa009529e>] set_regdom+0x28e/0x4c0 [cfg80211]
-> #0 (cfg80211_mutex){+.+.+.}:
[<ffffffff8108587b>] __lock_acquire+0xe3b/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
[<ffffffffa009813f>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa009b12b>] nl80211_set_interface+0x3b/0x260 [cfg80211]
When looking at the correct code, the problem is quite
obvious. I'm not entirely sure which code paths lead
here, so until I can analyse it better let's just use
RCU to avoid the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using background scanning in mac80211 the time a scan needs to
finish can exceed 10 seconds. Hence, increase the scan results
expire time to 15 seconds which should be sufficient.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In cfg80211_upload_connect_keys(), we call add_key, set_default_key
and set_default_mgmt_key (if applicable) one by one. If one of these
operations fails, we should stop calling the following functions.
Because if the key is not added successfully, we should not set it as
default key anyway.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We invoke the cfg80211 set_default_key callback only for WEP key
configuring.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wext code I tried to not reconnect all the time
when the user wasn't really sure what they were doing,
like setting the BSSID back to the same value it was.
However, this optimisation should only be done while
associated so that setting the BSSID back to the same
value that it was actually triggers a new association
if not currently associated. To achieve, that, put the
relevant code into the !IDLE case instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_sme_scan_done() can be called (by fullmac cards) with
wdev->conn == NULL when CFG80211_SME_CONNECTING. We quit silently
instead of WARN_ON in this case.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were treating ieee80211_regdom module parameter hints
as core hints, this means we were not letting the user help
compliance further when using the module parameter. It also
meant that users with a device with a custom regulatory
domain set (wiphy->custom_regulatory) using this module
parameter were being stuck to the original default core
static regualtory domain. We fix this by using the static
cfg80211_regdomain alpha2 as the core hint and treating the
module parameter separately.
All iwlwifi and ath5k/ath9k/ar9170 devices which world roam
set the wiphy->custom_regulatory. This change allows users
using this module parameter to have it trated as a a proper
user hint and not have it ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The work that we cancel there requires the cfg80211_mutex,
so we can't cancel it under the mutex, which is fine, we
can just move it to after the locked section.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_set_wpa_version completely missed the use case when disabling
WPA, considering IW_AUTH_WPA_VERSION_DISABLED an invalid argument. This
caused weird error messages in wpa_supplicant.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "what-was-I-thinking-if-anything" patch. Clearly,
if cfg80211_send_disassoc() does wdev_lock() and then
calls __cfg80211_send_disassoc(), the latter shouldn't
lock again. And the sme_state test is ... no further
comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.
For example (from hwsim):
$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
freq: 2462
beacon interval: 100
capability: ESS ShortSlotTime (0x0401)
signal: -50.00 dBm
SSID: j
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Paramater set: channel 11
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel reported that you can't set the SSID from "foo" to
"bar". I tried reproducing, but used different values,
with different lengths, and thus never saw the obvious
problem.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is only used internally, _while_ connected.
If we use it, the sequence
# iwconfig wlan1 essid foo
<connects>
# iwconfig wlan1 essid ""
<disconnects>
# iwconfig
will still display "foo" as the SSID afterwards, which
is obviously quite bogus. Fix this by only displaying
the wext SSID, if present.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the wext BSSID which may be NULL if
you haven't explicitly set one, we should instead use
the current_bss pointer -- if that's NULL we aren't
connected anyway. Fixes missing signal quality output
reported to me internally at Intel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cfg80211_sme_disassoc() function is already holding
a lock here that cfg80211_mlme_deauth() would take, so
it needs to use __cfg80211_mlme_deauth() instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids memcpy from wdev->wext.ibss.bssid if it is NULL.
This could happen if we SIOCGIWAP before SIOCSIWAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two small bugs:
1) the connect variable is already initialised, and the
assignment to auth_type overwrites the previous setting
with a wrong value
2) when all authentication attempts fail, we need to report
that we couldn't connect
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_wext_giwrate doesn't lock the wdev, so it
cannot access current_bss race-free. Also, there's
little point in trying to ask the driver for an AP
that it never told us about, so avoid that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Potential memory leak via msg pointer in nl80211_get_key() function.
Signed-off-by: Niko Jokinen <ext-niko.k.jokinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless extensions have the unfortunate problem that events
are multicast netlink messages, and are not independent of
pointer size. Thus, currently 32-bit tasks on 64-bit platforms
cannot properly receive events and fail with all kinds of
strange problems, for instance wpa_supplicant never notices
disassociations, due to the way the 64-bit event looks (to a
32-bit process), the fact that the address is all zeroes is
lost, it thinks instead it is 00:00:00:00:01:00.
The same problem existed with the ioctls, until David Miller
fixed those some time ago in an heroic effort.
A different problem caused by this is that we cannot send the
ASSOCREQIE/ASSOCRESPIE events because sending them causes a
32-bit wpa_supplicant on a 64-bit system to overwrite its
internal information, which is worse than it not getting the
information at all -- so we currently resort to sending a
custom string event that it then parses. This, however, has a
severe size limitation we are frequently hitting with modern
access points; this limitation would can be lifted after this
patch by sending the correct binary, not custom, event.
A similar problem apparently happens for some other netlink
users on x86_64 with 32-bit tasks due to the alignment for
64-bit quantities.
In order to fix these problems, I have implemented a way to
send compat messages to tasks. When sending an event, we send
the non-compat event data together with a compat event data in
skb_shinfo(main_skb)->frag_list. Then, when the event is read
from the socket, the netlink code makes sure to pass out only
the skb that is compatible with the task. This approach was
suggested by David Miller, my original approach required
always sending two skbs but that had various small problems.
To determine whether compat is needed or not, I have used the
MSG_CMSG_COMPAT flag, and adjusted the call path for recv and
recvfrom to include it, even if those calls do not have a cmsg
parameter.
I have not solved one small part of the problem, and I don't
think it is necessary to: if a 32-bit application uses read()
rather than any form of recvmsg() it will still get the wrong
(64-bit) event. However, neither do applications actually do
this, nor would it be a regression.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current function for sending events first allocates the
event stream buffer, and then an skb to copy the event stream
into. This can be done in one go. Also, the current function
leaks kernel data to userspace in a 4 uninitialised bytes,
initialise those explicitly. Finally also add a few useful
comments, as opposed to the current comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes wireless extensions netns aware. The
tasklet sending the events is converted to a work
struct so that we can rtnl_lock() in it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes generic netlink network namespace aware. No
generic netlink families except for the controller family
are made namespace aware, they need to be checked one by
one and then set the family->netnsok member to true.
A new function genlmsg_multicast_netns() is introduced to
allow sending a multicast message in a given namespace,
for example when it applies to an object that lives in
that namespace, a new function genlmsg_multicast_allns()
to send a message to all network namespaces (for objects
that do not have an associated netns).
The function genlmsg_multicast() is changed to multicast
the message in just init_net, which is currently correct
for all generic netlink families since they only work in
init_net right now. Some will later want to work in all
net namespaces because they do not care about the netns
at all -- those will have to be converted to use one of
the new functions genlmsg_multicast_allns() or
genlmsg_multicast_netns() whenever they are made netns
aware in some way.
After this patch families can easily decide whether or
not they should be available in all net namespaces. Many
genl families us it for objects not related to networking
and should therefore be available in all namespaces, but
that will have to be done on a per family basis.
Note that this doesn't touch on the checkpoint/restart
problem where network namespaces could be used, genl
families and multicast groups are numbered globally and
I see no easy way of changing that, especially since it
must be possible to multicast to all network namespaces
for those families that do not care about netns.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to force drivers to advertise their interface
types, don't just disallow creating new interfaces with
unadvertised types but also disallow setting them UP.
Additionally, add some validation on the operations the
drivers support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've named the registered devices 'drv' sometimes,
thinking of "driver", which is not what it is, it's
the internal representation of a wiphy, i.e. a
device. Let's clean up the naming once and and use
'rdev' aka 'registered device' everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Over time, a lot of locking issues have crept into
the smarts of cfg80211, so e.g. scan completion can
race against a new scan, IBSS join can race against
leaving an IBSS, etc.
Introduce a new per-interface lock that protects
most of the per-interface data that we need to keep
track of, and sprinkle assertions about that lock
everywhere. Some things now need to be offloaded to
work structs so that we don't require being able to
sleep in functions the drivers call. The exception
to that are the MLME callbacks (rx_auth etc.) that
currently only mac80211 calls because it was easier
to do that there instead of in cfg80211, and future
drivers implementing those calls will, if they ever
exist, probably need to use a similar scheme like
mac80211 anyway...
In order to be able to handle _deauth and _disassoc
properly, introduce a cookie passed to it that will
determine locking requirements.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sparse warns about a number of things, and one of them
(use_mfp shadowed variable) actually is a bug, fix all
of them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we call that cfg80211_put_dev(), but that is
misleading. With the new convention of using 'rdev' for
registered_device variables, also call that function
cfg80211_unlock_rdev().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code in mac80211 could send a deauth
frame under certain circumstances even if nothing
had ever requested an authentication. This has been
fixed with the rework there, so cfg80211 can now
warn again about spurious events to catch possible
future drivers or mac80211 regressions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the mac80211 mlme cleanup, we can require that
the MLME functions in cfg80211 can sleep. This will
simplify future work in cfg80211 a lot.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We shouldn't be looking at the ssid_len for non-IBSS,
and for IBSS we should also return an error on trying
to leave an IBSS while not in or joining an IBSS.
This fixes an issue where we wouldn't disconnect() on
an interface being taken down since there's no SSID
configured this way.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we don't really know that well in the kernel,
let's let the SME control whether it wants to use
reassociation or not, by allowing it to give the
previous BSSID in the associate() parameters.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connecting to an ESSID manually, we may not set the BSSID, and thus
wdev->wext.connect.bssid will be NULL.
wdev->current_bss is always updated when a connection is established so we
should check it first.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: Advertise ciphers via WE according to driver capability"
unfortunately broke iwrange -- it used the variable c
that needs to be 0 for the channel list.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In this case, only one cipher makes sense, unlike for
connect() where it may be possible to have the card or
driver select.
No changes to mac80211 due to the way the structs are
laid out -- but the loop in net/mac80211/cfg.c will
degrade to just zero or one passes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible that there are different BSS structs with
the same BSSID, but we cannot authenticate with multiple
of them them because we need the BSSID to be unique for
deauthenticating/disassociating.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to avoid problems with BSS structs going away
while they're in use, I've long wanted to make cfg80211
keep track of them. Without the SME, that wasn't doable
but now that we have the SME we can do this too. It can
keep track of up to four separate authentications and
one association, regardless of whether it's controlled
by the cfg80211 SME or the userspace SME.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function from mac80211 seems generally useful, and
I will need it in cfg80211 soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the interface is brought down, we need to
reset the auth algorithm because wpa_supplicant
doesn't reset it, and then we fail to use shared
key auth when required later.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the userspace SME is in control, we are currently not sending
events, but this means that any userspace applications using wext
or nl80211 to receive events will not know what's going on unless
they can also interpret the nl80211 assoc event. Since we have all
the required code, let the SME follow events from the userspace
SME, this even means that you will be refused to connect() while
the userspace SME is in control and connected.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By dropping the noise reporting, we can implement
wireless stats in cfg80211. We also make the
handler return NULL if we have no information,
which is possible thanks to the recent wext change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For now, let's implement that using a very hackish way:
simply mirror the wext API in the cfg80211 API. This
will have to be changed later when we implement proper
bitrate API.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements siocsiwap/giwap for WDS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just on/off and timeout, and with a hacky cfg80211 method
until we figure out what we want, though this is probably
sufficient as we want to use pm_qos for wifi everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to make it possible to use the cfg80211
connect() API with wireless extensions, and because the
previous patch added emulation of that API with auth()
and assoc(), by extension also supports wext on that.
At the same time, removes code from mac80211 for wext,
but doesn't yet clean up mac80211's mlme code more.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code to cfg80211 so that drivers (mac80211 right
now) that don't implement connect but rather auth/assoc can
still be used with the nl80211 connect command. This will
also be necessary for the wext compat code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the cfg80211 connect/disconnect API.
The goal here is to run the AUTH and ASSOC steps in one call.
This is needed for some fullmac cards that run both steps
directly from the target, after the host driver sends a
connect command.
Additionally, all the new crypto parameters for connect()
are now also valid for associate() -- although associate
requires the IEs to be used, the information can be useful
for drivers and should be given.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This introduces a new NL80211_CMD_TESTMODE for testing
and calibration use with nl80211. There's no multiplexing
like like iwpriv had, and the command is not available by
default, it needs to be explicitly enabled in Kconfig and
shouldn't be enabled in most kernels.
The command requires a wiphy index or interface index to
identify the device to operate on, and the new TESTDATA
attribute. There also is API for sending replies to the
command, and testmode multicast messages (on a testmode
multicast group).
I've also updated mac80211 to be able to pass through the
command to the driver, since it itself doesn't implement
the testmode command.
Additionally, to give people an idea of how to use the
command, I've added a little code to hwsim that makes use
of the new command to set the powersave mode, this is
currently done via debugfs and should remain there, and
the testmode command only serves as an example of how to
use this best -- with nested netlink attributes in the
TESTDATA attribute. A hwsim testmode tool can be found at
http://git.sipsolutions.net/hwsim.git/. This tool is BSD
licensed so people can easily use it as a basis for their
own internal fabrication and validation tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is never changed by the function, so can be marked const.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable isn't necessary -- the wext code keeps
track of the BSSID itself, and otherwise we have
current_bss.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding GFP_ATOMIC everywhere, add a
new function parameter that gets the flags from the
caller. Obviously then I need to update all callers
(all of them in mac80211), and it turns out that now
it's ok to use GFP_KERNEL in almost all places.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I don't like the 'extern' keyword much when it's not
necessary, it makes lines rather long.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move a break statement to the correct place _after_ the
#endif, otherwise w/o WIRELESS_EXT things break badly.
Also, while touching this code, do a cleanup and assign
dev->ieee80211_ptr to a new variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way I initially thought we could do wireless extensions
is by making all the compat code in cfg80211 be independent
of CONFIG_WIRELESS_EXT, but this is turning out to not be
feasible. Therefore, fix the Kconfig help text and make the
option default to yes, so people won't get a nasty surprise
when mac80211 will get rid of its 'select WIRELESS_EXT' any
time now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, wext drivers cannot return NULL for stats even though
that would make the ioctl return -EOPNOTSUPP because that would
mean they are no longer listed in /proc/net/wireless. This patch
changes the wext core's behaviour to list them if they have any
wireless_handlers, but only show their stats when available, so
that drivers can start returning NULL if stats are currently not
available, reducing confusion for e.g. IBSS.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having mac80211 do it itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only set the sizes for WEP40 and WEP104.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It isn't very useful to scan the same channel more than once
during a given scan, and some hardware (notably iwlwifi) can
only scan a limited number of channels at a time. To prevent
any overflows, simply disallow scanning any channel multiple
times in a given scan command. This is a small change in the
userspace ABI, but the only user, wpa_supplicant, never asks
for a scan with the same frequency listed twice.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To ease multiple apps working together smoothly,
send a notification when a scan is started.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there was a reason I'm passing the ifidx I cannot
remember it any more and don't see one now, so let's
just pass the pointer itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code in cfg80211's cfg80211_bss_update erroneously
grabs a reference to the BSS, which means that it will
never be freed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to unlock cfg80211_mutex in one fail path of
nl80211_set_wiphy.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I disallowed interfering with stations on non-AP interfaces,
I not only forget mesh but also managed interfaces which need
this for the authorized flag. Let's actually validate everything
properly.
This fixes an nl80211 regression introduced by the interfering,
under which wpa_supplicant -Dnl80211 could not properly connect.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh Point interfaces can also set parameters, for example plink_open is
used to manually establish peer links from user-space (currently via
iw). Add Mesh Point to the check in nl80211_set_station.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b2a151a288 added a check that prevents adding or deleting
stations on non-AP interfaces. Adding and deleting stations is
supported for Mesh Point interfaces, so add Mesh Point to that check as
well.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfkill currently requires a global lock within the
rfkill_register() function, and holds that lock over
calls to the set_block() methods. This means that we
cannot hold a lock around rfkill_register() that we
also require in set_block(), directly or indirectly.
Fix cfg80211 to register rfkill outside the block
locked by its global lock. Much of what cfg80211 does
in the locked block doesn't need to be locked anyway.
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes spares warning:
net/wireless/util.c:261:5: warning:
symbol 'ieee80211_get_mesh_hdrlen' was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be easier on drivers and users, have cfg80211 register an
rfkill structure that drivers can access. When soft-killed,
simply take down all interfaces; when hard-killed the driver
needs to notify us and we will take down the interfaces
after the fact. While rfkilled, interfaces cannot be set UP.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces new cfg80211 API to set the TX power
via cfg80211, puts the wext code into cfg80211 and updates
mac80211 to use all that. The -ENETDOWN bits are a hack but
will go away soon.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an incorrect assumption (BUG_ON) made in
cfg80211 when handling country IE regulatory requests.
The assumption was that we won't try to call_crda()
twice for the same event and therefore we will not
recieve two replies through nl80211 for the regulatory
request. As it turns out it is true we don't call_crda()
twice for the same event, however, kobject_uevent_env()
*might* send the udev event twice and/or userspace can
simply process the udev event twice. We remove the BUG_ON()
and simply ignore the duplicate request.
For details refer to this thread:
http://marc.info/?l=linux-wireless&m=124149987921337&w=2
Cc: stable@kernel.org
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
(Reconcile this w/ previous version of patch posted with same
subject... -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the key length for validation, use the
constants Zhu Yi recently added and add one for AES_CMAC too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a scan finishes only the program that asked for it
knows what kind of scan it was; let's tell everybody else
about the scan parameters as well so they can evaluate
the result of the scan better. Also helps with debugging.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have some validation code in mac80211 but said code will
force an invalid AID to 0 which isn't a valid AID either;
instead require a valid AID (1-2007) to be passed in from
userspace in cfg80211 already. Also move the code before
the race comment since it can only be executed during STA
addition and thus is not racy.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").
This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use genl_register_family_with_ops() instead of a copy.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device drivers using wiphy_apply_custom_regulatory() want some
regulatory settings applied to their wiphy, if no bands were
configured on the wiphy then something went wrong.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If CONFIG_CFG80211_DEBUGFS is enabled and CONFIG_MAC80211_DEBUGFS is
not, compilation fails in net/wireless/debugfs.c:
net/wireless/debugfs.c: In function 'cfg80211_debugfs_drv_add':
net/wireless/debugfs.c:117: error: 'struct cfg80211_registered_device'
has no member named 'debugfs'
The debugfs filed is needed if and only if CONFIG_CFG80211_DEBUGFS is
enabled, so use that instead of CONFIG_MAC80211_DEBUGFS.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a race on access to last_request and its alpha2
through reg_is_valid_request() and us possibly processing
first another regulatory request on another CPU. We avoid
this improbably race by locking with the cfg80211_mutex as
we should have done in the first place. While at it add
the assert on locking on reg_is_valid_request().
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change, but it will make the race
fix easier to spot in my next patch.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional change except we save a kfree(rd) and
allows us to clean this code up a bit after this. We do
avoid an unnecessary kfree(NULL) but calling that was OK too.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some applications using wireless extensions expect to be able to
remove a key that doesn't exist. One example is wpa_supplicant
which doesn't actually change behaviour when running into an
error while trying to do that, but it prints an error message
which users interpret as wpa_supplicant having problems.
The safe thing to do is not change the behaviour of wireless
extensions any more, so when the driver reports -ENOENT let
the wext bridge code return success to userspace. To guarantee
this, also document that drivers should return -ENOENT when the
key doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to mark their cfg80211_ops tables const.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate RSC (NL80211_ATTR_KEY_SEQ) length in nl80211/cfg80211 instead
of having to do this in all the drivers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the cfg80211 specific stuff to new cfg80211 debugfs
entries. Non-mac80211 will also get these entries now. There were
only 4 which we take:
rts_threshold
fragmentation_threshold
short_retry_limit
long_retry_limit
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to nl80211 userspace can be very specific upon device
configuration. Before processing the request for the new HT40
channel types (HT40- or HT40+) we need to ensure we can use them
regulatory-wise. This wasn't required with wireless extensions as
specifying the channel type wasn't not available and configuration
was done towards the end implicitly upon association or reception
of beacons from the AP. For the new nl80211 we have to check this
when configuring the interfaces explicitly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its possible for cfg80211 to have scheduled the work and for
the global workqueue to not have kicked in prior to a cfg80211
driver's regulatory hint or wiphy_apply_custom_regulatory().
Although this is very unlikely its possible and should fix
this race. When this race would happen you are expected to have
hit a null pointer dereference panic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another design flaw in wireless extensions (is anybody
surprised?) in the way it handles the iw_encode_ext
structure: The structure is part of the 'extra' memory
but contains the key length explicitly, instead of it
just being the length of the extra buffer - size of
the struct and using the explicit key length only for
the get operation (which only writes it).
Therefore, we have this layout:
extra: +-------------------------+
| struct iw_encode_ext { |
| ... |
| u16 key_len; |
| u8 key[0]; |
| }; |
+-------------------------+
| key material |
+-------------------------+
Now, all drivers I checked use ext->key_len without
checking that both key_len and the struct fit into the
extra buffer that has been copied from userspace. This
leads to a buffer overrun while reading that buffer,
depending on the driver it may be possible to specify
arbitrary key_len or it may need to be a proper length
for the key algorithm specified.
Thankfully, this is only exploitable by root, but root
can actually cause a segfault or use kernel memory as
a key (which you can even get back with siocgiwencode
or siocgiwencodeext from the key buffer).
Fix this by verifying that key_len fits into the buffer
along with struct iw_encode_ext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nlmsg_new() adds the size of the netlink header to the value
that has been passed as parameter. If NLMSG_GOODSIZE is selected,
we request an allocation of one memory page plus the size of the
header. Instead, NLMSG_DEFAULT_SIZE should be used since it
already substracts the size of the Netlink header.
I have the impression that the similar naming in both constant
is error prone when using it with nlmsg_new(). This is already
documented in include/net/netlink.h
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though they are true, they cause sparse to complain
because it doesn't see the __acquires(dev_base_lock) on
dev_seq_start() because it is only added to the function
in net/core/dev.c, not the header file. To keep track of
the nesting correctly we should probably annotate those
functions publically, but for now let's just remove the
annotation I added to wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting a key with NL80211_CMD_NEW_KEY, we should allow the key
sequence number (RSC) to be set in order to allow replay protection to
work correctly for group keys. This patch documents this use for
nl80211 and adds the couple of missing pieces in nl80211/cfg80211 and
mac80211 to support this. In addition, WEXT SIOCSIWENCODEEXT compat
processing in cfg80211 is extended to handle the RSC (this was already
specified in WEXT, but just not implemented in cfg80211/mac80211).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_ATTR_CONTROL_PORT flag for NL80211_CMD_ASSOCIATE to
allow user space to indicate that it will control the IEEE 802.1X port
in station mode. Previously, mac80211 was always marking the port
authorized in station mode. This was enough when drop_unencrypted flag
was set. However, drop_unencrypted can currently be controlled only
with WEXT and the current nl80211 design does not allow fully secure
configuration. Fix this by providing a mechanism for user space to
control the IEEE 802.1X port in station mode (i.e., do the same that
we are already doing in AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is currently not possible to modify station flags, but that
capability would be very useful. This patch introduces a new
nl80211 attribute that contains a set/mask for station flags,
and updates the internal API (and mac80211) to mirror that.
The new attribute is parsed before falling back to the old so
that userspace can specify both (if it can) to work on all
kernels.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_STA_FLAG_MFP was forgotten from sta_flags_policy. The previous
version added the flag due to the loop used in parse_station_flags,
but the proper behavior would be to allow nla_parse_nested() to go
through the policy for all flags.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move key handling wireless extension ioctls from mac80211 to cfg80211
so that all drivers that implement the cfg80211 operations get wext
compatibility.
Note that this drops the SIOCGIWENCODE ioctl support for getting
IW_ENCODE_RESTRICTED/IW_ENCODE_OPEN. This means that iwconfig will
no longer report "Security mode:open" or "Security mode:restricted"
for mac80211. However, what we displayed there (the authentication
algo used) was actually wrong -- linux/wireless.h states that this
setting is meant to differentiate between "Refuse non-encoded packets"
and "Accept non-encoded packets".
(Combined with "cfg80211: fix a couple of bugs with key ioctls". -- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, get_wireless_stats is racy by _design_. This is
because it returns a buffer, which needs to be statically
allocated since it cannot be freed if it was allocated
dynamically. Also, SIOCGIWSTATS and /proc/net/wireless use
no common lock, and /proc/net/wireless accesses are not
synchronised against each other. This is a design flaw in
get_wireless_stats since the beginning.
This patch fixes it by wrapping /proc/net/wireless accesses
with the RTNL so they are protected against each other and
SIOCGIWSTATS. The more correct method of fixing this would
be to pass in the buffer instead of returning it and have
the caller take care of synchronisation of the buffer, but
even then most drivers probably assume that their callback
is protected by the RTNL like all other wext callbacks.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On non-AP interfaces userspace has no business interfering with
the station management, this can confuse mac80211 (and other
drivers probably wouldn't support it anyway). Allow adding and
removing stations only on AP interfaces.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make it more apparent in the code what is for wext
only (and needs to be #ifdef'ed) put all the info for
wext into a substruct in each wireless_dev.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function to parse a struct iw_freq has a stupid bug,
it returns NULL when the channel cannot be found at all,
but NULL is supposed to mean "auto". Fix this by checking
the return value of ieee80211_get_channel() and returning
ERR_PTR(-EINVAL) if it returned NULL (channel not found).
This fixes an issue where you could say (in IBSS mode)
iwconfig wlan0 channel 21
and it would use channel 1 instead because that's the
first available channel with IBSS allowed (which is what
the "auto" setting uses).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_ASSOCIATE request must be able to indicate whether
management frame protection (IEEE 802.11w) is being used. mac80211 was
able to use MFP in client mode only with WEXT, but the new
NL80211_ATTR_USE_MFP attribute will allow this to be done with
nl80211, too.
Since we are currently using nl80211 for MFP only with drivers that
use user space SME, only MFP disabled and required values are
used. However, the NL80211_ATTR_USE_MFP attribute is an enum that can
be extended with MFP optional in the future, if that is needed with
some drivers (e.g., if the RSN IE is generated by the driver).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse complaint:
CHECK net/wireless/nl80211.c
net/wireless/nl80211.c:3694:6:
warning: symbol 'nl80211_send_mlme_timeout'
was not declared. Should it be static?
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IE buffer was allocated, the pub.information_elements pointer
was also changed to the allocated space. So we must not assume anymore
that the pointer points at the "found" tail.
So if it was allocated previously, take the codebranch that grows the
buffer size (if necessary) and put the data into the allocated buffer.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes an unnecessary ksize() call. krealloc() will do this
test internally and won't perform any allocation if the space is
already sufficient to hold the data.
So remove the redundant check.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0ad8acaf "cfg80211: fix NULL pointer deference in
reg_device_remove()" added a check that last_request is non-NULL,
rendering the 2nd check superfluous. While there, rearrange the code a
bit so it's a little more straight forward.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to lock using the cfg80211_mutex in
wiphy_apply_custom_regulatory(). Without the lock
there is possible race between processing a reply from CRDA
and a driver calling wiphy_apply_custom_regulatory(). During
the processing of the reply from CRDA we free last_request and
wiphy_apply_custom_regulatory() eventually accesses an
element from last_request in the through freq_reg_info_regd().
This is very difficult to reproduce (I haven't), it takes us
3 hours and you need to be banging hard, but the race is obvious
by looking at the code.
This should only affect those who use this caller, which currently
is ath5k, ath9k, and ar9170.
EIP: 0060:[<f8ebec50>] EFLAGS: 00210282 CPU: 1
EIP is at freq_reg_info_regd+0x24/0x121 [cfg80211]
EAX: 00000000 EBX: f7ca0060 ECX: f5183d94 EDX: 0024cde0
ESI: f8f56edc EDI: 00000000 EBP: 00000000 ESP: f5183d44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 14617, ti=f5182000 task=f3934d10 task.ti=f5182000)
Stack: c0505300 f7ca0ab4 f5183d94 0024cde0 f8f403a6 f8f63160 f7ca0060 00000000
00000000 f8ebedf8 f5183d90 f8f56edc 00000000 00000004 00000f40 f8f56edc
f7ca0060 f7ca1234 00000000 00000000 00000000 f7ca14f0 f7ca0ab4 f7ca1289
Call Trace:
[<f8ebedf8>] wiphy_apply_custom_regulatory+0x8f/0x122 [cfg80211]
[<f8f3f798>] ath_attach+0x707/0x9e6 [ath9k]
[<f8f45e46>] ath_pci_probe+0x18d/0x29a [ath9k]
[<c023c7ba>] pci_device_probe+0xa3/0xe4
[<c02a860b>] really_probe+0xd7/0x1de
[<c02a87e7>] __driver_attach+0x37/0x55
[<c02a7eed>] bus_for_each_dev+0x31/0x57
[<c02a83bd>] driver_attach+0x16/0x18
[<c02a78e6>] bus_add_driver+0xec/0x21b
[<c02a8959>] driver_register+0x85/0xe2
[<c023c9bb>] __pci_register_driver+0x3c/0x69
[<f8e93043>] ath9k_init+0x43/0x68 [ath9k]
[<c010112b>] _stext+0x3b/0x116
[<c014a872>] sys_init_module+0x8a/0x19e
[<c01049ad>] sysenter_do_call+0x12/0x21
[<ffffe430>] 0xffffe430
=======================
Code: 0f 94 c0 c3 31 c0 c3 55 57 56 53 89 c3 83 ec 14 8b 74 24 2c 89 54 24 0c 89 4c 24 08 85 f6 75
06 8b 35 c8 bb ec f8 a1 cc bb ec f8 <8b> 40 04 83 f8 03 74 3a 48 74 37 8b 43 28 85 c0 74 30 89 c6
8b
EIP: [<f8ebec50>] freq_reg_info_regd+0x24/0x121 [cfg80211] SS:ESP 0068:f5183d44
Cc: stable@kernel.org
Reported-by: Nataraj Sadasivam <Nataraj.Sadasivam@Atheros.com>
Reported-by: Vivek Natarajan <Vivek.Natarajan@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another bug in the "cfg80211: do not replace BSS structs" patch,
a forgotten length update leads to bogus data being stored and
passed to userspace, often truncated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SME needs to be notified when the authentication or association
attempt times out and MLME has stopped processing in order to allow
the SME to decide what to do next.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the JOIN_IBSS command look at the beacon interval
attribute to see if the user requested a specific beacon
interval, if not default to 100 TU (wext too).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fact that these are exported is a technical detail
of the conversion period -- we don't want anybody to
start relying on these. Ultimately we want things to
use cfg80211 only, and once everything that is in wext
is converted to cfg80211 drivers will not need to touch
wext _at all_.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we leave an IBSS, we should clear the SSID and not just the
BSSID, but since WEXT allows configuring while the interface is
down we must not clear it when leaving due to taking the iface
down, so some complications are needed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 attributes that can be used with NL80211_CMD_SET_WIPHY
and NL80211_CMD_GET_WIPHY to manage fragmentation/RTS threshold and
retry limits.
Since these values are stored in struct wiphy, remove the local copy
from mac80211 where feasible (frag & rts threshold). The retry limits
are currently needed in struct ieee80211_conf, but these could be
eventually removed since the driver should have access to the values
in struct wiphy.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds IBSS API along with (preliminary) wext handlers.
The wext handlers can only do IBSS so you need to call them
from your own wext handlers if the mode is IBSS.
The nl80211 API requires
* an SSID
* a channel (frequency) for the case that a new IBSS
has to be created
It optionally supports
* a flag to fix the channel
* a fixed BSSID
The cfg80211 code also takes care to leave the IBSS before
the netdev is set down. If wireless extensions are used, it
also caches values when the interface is down and instructs
the driver to join when the interface is set up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we have ->deauth and ->disassoc we can support the
wext SIWMLME call directly without driver wext handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When listing all wireless netdevs in the system this
is useful to print which wiphy they belong to. Just
add the attribute, any program that doesn't care will
just ignore it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
That will make the various cases where the WARN_ON
can happen distinguishable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the necessary code and fields to let drivers specify
their cipher capabilities and exports them to userspace. Also
update mac80211 to export the ciphers it has.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a netlink channel put helper, nl80211_msg_put_channel(),
which we will also make use of later for the beacon hints events.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of our documented API we always respect the orig_flag
settings on a channel. We forgot to follow this for the beacon
hints.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of just passing the cfg80211-requested IEs, pass
the locally generated ones as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new attribute for a wiphy that tells
userspace how long the information elements added to a probe
request frame can be at most. It also updates the at76 to
advertise that it cannot support that, and, for now until I
can fix that, iwlwifi too.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added cfg80211_inform_bss() for full-mac devices to use.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define a new nl80211 event, NL80211_CMD_MICHAEL_MIC_FAILURE, to be
used to notify user space about locally detected Michael MIC failures.
This matches with the MLME-MICHAELMICFAILURE.indication() primitive.
Since we do not actually have TSC in the skb anymore when
mac80211_ev_michael_mic_failure() is called, that function is changed
to take in the TSC as an optional parameter instead of as a
requirement to include the TSC after the hdr field (which we did not
really follow). For now, TSC is not included in the events from
mac80211, but it could be added at some point.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, nl80211 mlme events were generated only for received
deauthentication and disassociation frames. We need to do the same for
locally generated ones in order to let applications know that we
disconnected (e.g., when AP does not reply to a probe). Rename the
nl80211 and cfg80211 functions (s/rx_//) to make it clearer that they
are used for both received and locally generated frames.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_ATTR_AUTH_TYPE is a required parameter for
NL80211_CMD_AUTHENTICATE. We are currently (by chance) defaulting to
open system authentication if the attribute is not specified. It is
better to just reject the invalid command.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove duplicated #include in net/wireless/core.h.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes nl80211 to:
* validate that any IE input is a valid IE (stream)
* move some validation code before locking
* require that a reason code is given for both deauth/disassoc
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead, allocate extra IE memory if necessary. Normally,
this isn't even necessary since there's enough space.
This is a better way of correcting the "held BSS can
disappear" issue, but also a lot more code. It is also
necessary for proper auth/assoc BSS handling in the
future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a probe response frame we can replace the
BSS struct in our list -- but if that struct is held then
we need to hold the new one as well.
We really should fix this completely and not replace the
struct, but this is a bandaid for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And update description and feature-removal schedule according
to the new plan.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reports that there's a circular locking dependency;
this is because cfg80211_dev_rename() will acquire the
cfg80211_mutex while the device mutex is held, while
this normally is done the other way around. The solution
is to open-code the device-getting in nl80211_set_wiphy
and require holding the mutex around cfg80211_dev_rename
rather than acquiring it within.
Also fix a bug -- rtnl locking is expected by drivers so
we need to provide it.
Reported-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In beacon filtering there needs to be a way to not expire the BSS even
when no beacons are received. Add an interface to cfg80211 to hold
BSS and make sure that it's not expired.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When somebody tries to set the interface mode to the existing
mode, don't ask the driver but silently accept the setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had left in code to allow interested developers to add
support for parsing country IEs when OLD_REG was enabled.
This never happened and since we're going to remove OLD_REG
lets just remove these comments and code for it.
This code path was never being entered so this has no
functional change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems a few users are using this module parameter although its not
recommended. People are finding it useful despite there being utilities
for setting this in userspace. I'm not aware of any distribution using
this though.
Until userspace and distributions catch up with a default userspace
automatic replacement (GeoClue integration would be nirvana) we copy
the ieee80211_regdom module parameter from OLD_REG to the new reg
code to help these users migrate.
Users who are using the non-valid ISO / IEC 3166 alpha "EU" in their
ieee80211_regdom module parameter and migrate to non-OLD_REG enabled
system will world roam.
This also schedules removal of this same ieee80211_regdom module
parameter circa March 2010. Hope is by then nirvana is reached and
users will abandoned the module parameter completely.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The incorrect assumption is the last regulatory request
(last_request) is always a country IE when processing
country IEs. Although this is true 99% of the time the
first time this happens this could not be true.
This fixes an oops in the branch check for the last_request
when accessing drv_last_ie. The access was done under the
assumption the struct won't be null.
Note to stable: to port to 29 replace as follows, only 29 has
country IE code:
s|NL80211_REGDOM_SET_BY_COUNTRY_IE|REGDOM_SET_BY_COUNTRY_IE
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although EU is a bogus alpha2 we need to process the send request
as our code depends on last_request being set.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this. In addition, make the error values consistent by using
EOPNOTSUPP instead of semi-random assortment of errno values.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not want to require all the drivers using cfg80211 to need to do
this or to be prepared to handle these commands when the interface is
down.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the used authentication type and reason code are valid here
so that drivers/mac80211 do not need to care about this. In addition,
remove the unnecessary validation of SSID attribute length which is
taken care of by netlink policy.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functionality that NL80211_CMD_SET_MGMT_EXTRA_IE provided can now
be achieved with cleaner design by adding IE(s) into
NL80211_CMD_TRIGGER_SCAN, NL80211_CMD_AUTHENTICATE,
NL80211_CMD_ASSOCIATE, NL80211_CMD_DEAUTHENTICATE, and
NL80211_CMD_DISASSOCIATE.
Since this is a very recently added command and there are no known (or
known planned) applications using NL80211_CMD_SET_MGMT_EXTRA_IE and
taken into account how much extra complexity it adds to the IE
processing we have now (and need to add in the future to fix IE order
in couple of frames), it looks like the best option is to just remove
the implementation of this command for now. The enum values themselves
are left to avoid changing the nl80211 command or attribute numbers.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new nl80211 commands to allow user space to request
authentication and association (and also deauthentication and
disassociation). The commands are structured to allow separate
authentication and association steps, i.e., the interface between
kernel and user space is similar to the MLME SAP interface in IEEE
802.11 standard and an user space application takes the role of the
SME.
The patch introduces MLME-AUTHENTICATE.request,
MLME-{,RE}ASSOCIATE.request, MLME-DEAUTHENTICATE.request, and
MLME-DISASSOCIATE.request primitives. The authentication and
association commands request the actual operations in two steps
(assuming the driver supports this; if not, separate authentication
step is skipped; this could end up being a separate "connect"
command).
The initial implementation for mac80211 uses the current
net/mac80211/mlme.c for actual sending and processing of management
frames and the new nl80211 commands will just stop the current state
machine from moving automatically from authentication to association.
Future cleanup may move more of the MLME operations into cfg80211.
The goal of this design is to provide more control of authentication and
association process to user space without having to move the full MLME
implementation. This should be enough to allow IEEE 802.11r FT protocol
and 802.11s SAE authentication to be implemented. Obviously, this will
also bring the extra benefit of not having to use WEXT for association
requests with mac80211. An example implementation of a user space SME
using the new nl80211 commands is available for wpa_supplicant.
This patch is enough to get IEEE 802.11r FT protocol working with
over-the-air mechanism (over-the-DS will need additional MLME
primitives for handling the FT Action frames).
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new nl80211 event notifications (and a new multicast group, "mlme")
for informing user space about received and processed Authentication,
(Re)Association Response, Deauthentication, and Disassociation frames in
station and IBSS modes (i.e., MLME SAP interface primitives
MLME-AUTHENTICATE.confirm, MLME-ASSOCIATE.confirm,
MLME-REASSOCIATE.confirm, MLME-DEAUTHENTICATE.indicate, and
MLME-DISASSOCIATE.indication). The event data is encapsulated as the 802.11
management frame since we already have the frame in that format and it
includes all the needed information.
This is the initial step in providing MLME SAP interface for
authentication and association with nl80211. In other words, kernel code
will act as the MLME and a user space application can control it as the
SME.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I added scanning to cfg80211, we got a lock dependency like this:
rtnl --> cfg80211_mtx
nl80211, on the other hand, has the reverse lock dependency:
cfg80211_mtx --> rtnl
which clearly is a bad idea. This patch reworks nl80211 to take these
two locks in the other order to fix the possible, and easily
triggerable, deadlock.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes nl80211 export the supported commands (command groups)
per wiphy so userspace has an idea what it can do -- this will be
required reading for userspace when we introduce auth/assoc /or/
connect for older hardware that cannot separate auth and assoc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scan capability added to cfg80211/nl80211 introduced a
dependency on nl80211 by cfg80211. We can thus no longer have
just cfg80211 without nl80211. Specifically, cfg80211_scan_done()
calls nl80211_send_scan_aborted() or nl80211_send_scan_done().
Now we remove the option for user to select nl80211. It will always
be compiled if user selects cfg80211.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS handlers
did not verify whether a function pointer is NULL (not supported by
the driver) before trying to call the function. The former nl80211
command is available for unprivileged users, too, so this can
potentially allow normal users to kill networking (or worse..) if
mac80211 is built without CONFIG_MAC80211_MESH=y.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the lowest value amongst countries which do enable 5 GHz operation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When they were part of the now defunct ieee80211 component, these
messages were only visible when special debugging settings were enabled.
Let's mirror that with a new lib80211 debugging Kconfig option.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
freq_diff is unsigned, so test before subtraction
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"cfg80211: add assert_cfg80211_lock() to ensure proper protection"
added assert_cfg80211_lock() calls into various places. At least
one of them, nl80211_send_wiphy(), should not have been there. That
triggers the BUG_ON in assert_cfg80211_lock() and pretty much kills
the kernel whenever someone runs hostapd.. Remove that call and make
assert_cfg80211_lock() use WARN_ON instead of BUG_ON to be a bit more
friendly to users.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we already have a regulatory request from the workqueue use that
and avoid a new kzalloc()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were passing value by value, lets just pass the struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.
This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.
All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current static world regulatory domain is too restrictive,
we can use some 5 GHz channels world wide so long as they do not
touch frequencies which require DFS. The compromise is we must
also enforce passive scanning and disallow usage of a mode of
operation that beacons: (AP | IBSS | Mesh)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables active scan and beaconing on Channels 1 through 11
on the static world regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers that agree on regulatory to share their
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was never happening but it was still wrong, so correct it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Truth of the matter this was confusing people so mark it as
unlikely as that is the case now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not protecting last_request there is a small possible race
between an 11d hint and another routine which calls reset_regdomains()
which can prevent a valid country IE from being processed. This is
not critical as it will still be procesed soon after but locking prior
to it is correct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so later on we can move the pending requests onto a
workqueue. By using the wiphy_idx instead of the wiphy we can
later easily check if the wiphy has disappeared or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling kobject_uevent_env() can fail mainly due to out of
memory conditions. We do not want to continue during such
conditions so propagate that as well instead of letting
cfg80211 load as if everything is peachy.
Additionally lets clarify that when CRDA is not called during
cfg80211's initialization _and_ if the error is not an -ENOMEM
its because kobject_uevent_env() failed to call CRDA, not because
CRDA failed. For those who want to find out why we also let you
do so by enabling the kernel config CONFIG_CFG80211_REG_DEBUG --
you'll get an actual stack trace.
So for now we'll treat non -ENOMEM kobject_uevent_env() failures as
non fatal during cfg80211's initialization.
CC: Greg KH <greg@kroah.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the core hint path more readable and allows for us to
later make it obvious under what circumstances we need locking or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If cfg80211 is built into the kernel there is perhaps a small
time window betwen nl80211_init() and regulatory_init() where
cfg80211_regdomain hasn't yet been initialized to let the
wireless core do its work. During that rare case and time
frame (if its even possible) we don't allow user regulatory
changes as cfg80211 is working on enabling its first regulatory
domain.
To check for cfg80211_regdomain we now contend the entire operation
using the cfg80211_mutex.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_drv_mutex is protecting more than the driver list,
this renames it and documents what its currently supposed to
protect.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will later be used by others, for now make use of it in
cfg80211_drv_by_wiphy_idx() to return early if an invalid
wiphy_idx has been provided.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Makes it clearer to read when comparing to ifidx
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous patch made cfg80211 generally aware of the signal
type a given hardware will give, so now it can implement
SIOCGIWRANGE itself, removing more wext stuff from mac80211.
Might need to be a little more parametrized once we have
more hardware using cfg80211 and new hardware capabilities.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It wasn't a good idea to make the signal type a per-BSS option,
although then it is closer to the actual value. Move it to be
a per-wiphy setting, update mac80211 to match.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no particular reason to not let untrusted users see
this information -- it's just the stations we're talking to,
packet counters for them and possibly some mesh things.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to various bugs in the software stack we end up having
to fill qual.qual; level should be used, but wpa_supplicant
doesn't properly ignore qual.qual, NM should use qual.level
regardless of that because qual.qual is 0 but doesn't handle
IW_QUAL_DBM right now.
So fill qual.qual with the qual.level value clamped to
-110..-40 dBm or just the regular 'unspecified' signal level.
This requires a mac80211 change to properly announce the
max_qual.qual and avg_qual.qual values.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scanned BSS entries are timestamped with jiffies, which doesn't
increment across suspend and hibernate. On resume, every BSS in the
scan list looks like it was scanned within the last 10 seconds,
irregardless of how long the machine was actually asleep. Age scan
results on resume with the time spent during sleep so userspace has a
clue how old they really are.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX/RX packet counters are needed to fill in RADIUS Accounting
attributes Acct-Output-Packets and Acct-Input-Packets. We already
collect the needed information, but only the TX/RX bytes were
previously exposed through nl80211. Allow applications to fetch the
packet counters, too, to provide more complete support for accounting.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications
to specify a set of information element(s) to be added into Probe
Request frames with NL80211_ATTR_IE. This provides support for the
MLME-SCAN.request primitive parameter VendorSpecificInfo and can be
used, e.g., to implement WPS scanning.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add empty function for case of CONFIG_NL80211=n:
net/wireless/scan.c:35: error: implicit declaration of function 'nl80211_send_scan_aborted'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a more flexible BSS lookup function so that mac80211 or
other drivers can actually use this for getting the BSS to
connect to.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces cfg80211_unlink_bss, a function to
allow a driver to remove a BSS from the internal list and
make it not show up in scan results any more -- this is
to be used when the driver detects that the BSS is no
longer available.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 users have their own allocated data in the per-BSS
private data, they will need to free this when the BSS struct is
destroyed. Add a free_priv method and fix one place where the BSS
was kfree'd rather than released properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds basic scan capability to cfg80211/nl80211 and
changes mac80211 to use it. The BSS list that cfg80211 maintains
is made driver-accessible with a private area in each BSS struct,
but mac80211 doesn't yet use it. That's another large project.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the regulatory domain is already set it is technically not an error
so do not pass an errno to userspace.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let users be more compliant if so desired.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to request strict regulatory settings to
be applied to its devices. This is desirable for devices where
proper calibration and compliance can only be gauranteed for
for the device's programmed regulatory domain. Regulatory
domain settings will be ignored until the device's own
regulatory domain is properly configured. If no regulatory
domain is received only the world regulatory domain will be
applied -- if OLD_REG (default to "US") is not enabled. If
OLD_REG behaviour is not acceptable to drivers they must
update their wiphy with a custom reuglatory prior to wiphy
registration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need more information than just who set the last regulatory domain,
as such lets just pass the last regulatory_request receipt. To do this we need
to move out to headers struct regulatory_request, and enum environment_cap. While
at it lets add documentation for enum environment_cap.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that the initial REGDOM_SET_BY_CORE upon wiphy registration
respects the wiphy->custom_regulatory setting. Without this and if OLD_REG
is disabled (which will be default soon as we remove it) the
wiphy->custom_regulatory is simply ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers without firmware can also have custom regulatory maps
which do not map to a specific ISO / IEC alpha2 country code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We ignore regulatory hints for the same alpha2 if we already
have processed the same alpha2 on the current regulatory domain.
For a driver regulatory_hint() this means we copy onto its
wiphy->regd the previously procesed regulatory domain from CRDA
without having to call CRDA again.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents user regulatory changes to be considered prior to previous
pending user, core or driver requests which have not be applied.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used by drivers on the reg_notifier()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds wiphy_apply_custom_regulatory() to be used by drivers
prior to wiphy registration to apply a custom regulatory domain.
This can be used by drivers that do not have a direct 1-1 mapping
between a regulatory domain and a country.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the standards only define 12 legacy rates, 32 is certainly
a sane upper limit and we don't need to use u64 everywhere. Add
sanity checking that no more than 32 rates are registered and
change the variables to u32 throughout.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help implement suspend/resume in mac80211, these
hooks will be run before the device is suspended and after it
resumes. Therefore, they can touch the hardware as much as
they want to.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new nl80211 command, NL80211_CMD_SET_MGMT_EXTRA_IE, can be used to
add arbitrary IE data into the end of management frames. The interface
allows extra IEs to be configured for each management frame subtype, but
only some of them (ProbeReq, ProbeResp, Auth, (Re)AssocReq, Deauth,
Disassoc) are currently accepted in mac80211 implementation.
This makes it easier to implement IEEE 802.11 extensions like WPS and
FT that add IE(s) into some management frames. In addition, this can
be useful for testing and experimentation purposes.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg
Luis R. Rodriguez
Helmut Schaa
Zhu Yi
Gábor Stefanik
David S. Miller
Christian Lamparter
Niko Jokinen
Samuel Ortiz
Samuel Ortiz
David Kilroy
Jiri Slaby
Andrey Yurovsky
Bob Copeland
Michał Mirosław
Pavel Roskin
Jouni Malinen
Pablo Neira Ayuso
Michael Buesch
Chris Wright
Jouni Malinen
Jussi Kivilinna
Huang Weiyi
Kalle Valo
Reinette Chatre
John W. Linville
Roel Kluin
Dan Williams
Randy Dunlap