In case we fail to establish the connection we must drain our pre-posted
login recieve work request before continuing safely with connection
teardown.
Fixes: a060b5629a ("IB/core: generic RDMA READ/WRITE API")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Amrani, Ram <Ram.Amrani@cavium.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make sure that the initiator port GUID is stored in ch->ini_guid.
Note: when initiating a connection sgid and dgid members in struct
sa_path_rec represent the source and destination GIDs. When accepting
a connection however sgid represents the destination GID and dgid the
source GID.
Fixes: commit 2bce1a6d22 ("IB/srpt: Accept GUIDs as port names")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
With the SRP protocol all RDMA operations are initiated by the target.
Since no RDMA operations are initiated by the initiator, do not grant
the initiator permission to submit RDMA reads or writes to the target.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
When using enhanced mode for IPoIB, two threads may execute xmit in
parallel to two different TX queues while the target is the same.
In this case, both of them will add the same neighbor to the path's
neigh link list and we might see the following message:
list_add double add: new=ffff88024767a348, prev=ffff88024767a348...
WARNING: lib/list_debug.c:31__list_add_valid+0x4e/0x70
ipoib_start_xmit+0x477/0x680 [ib_ipoib]
dev_hard_start_xmit+0xb9/0x3e0
sch_direct_xmit+0xf9/0x250
__qdisc_run+0x176/0x5d0
__dev_queue_xmit+0x1f5/0xb10
__dev_queue_xmit+0x55/0xb10
Analysis:
Two SKB are scheduled to be transmitted from two cores.
In ipoib_start_xmit, both gets NULL when calling ipoib_neigh_get.
Two calls to neigh_add_path are made. One thread takes the spin-lock
and calls ipoib_neigh_alloc which creates the neigh structure,
then (after the __path_find) the neigh is added to the path's neigh
link list. When the second thread enters the critical section it also
calls ipoib_neigh_alloc but in this case it gets the already allocated
ipoib_neigh structure, which is already linked to the path's neigh
link list and adds it again to the list. Which beside of triggering
the list, it creates a loop in the linked list. This loop leads to
endless loop inside path_rec_completion.
Solution:
Check list_empty(&neigh->list) before adding to the list.
Add a similar fix in "ipoib_multicast.c::ipoib_mcast_send"
Fixes: b63b70d877 ('IPoIB: Use a private hash table for path lookup in xmit path')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The locking order of vlan_rwsem (LOCK A) and then rtnl (LOCK B),
contradicts other flows such as ipoib_open possibly causing a deadlock.
To prevent this deadlock heavy flush is called with RTNL locked and
only then tries to acquire vlan_rwsem.
This deadlock is possible only when there are child interfaces.
[ 140.941758] ======================================================
[ 140.946276] WARNING: possible circular locking dependency detected
[ 140.950950] 4.15.0-rc1+ #9 Tainted: G O
[ 140.954797] ------------------------------------------------------
[ 140.959424] kworker/u32:1/146 is trying to acquire lock:
[ 140.963450] (rtnl_mutex){+.+.}, at: [<ffffffffc083516a>] __ipoib_ib_dev_flush+0x2da/0x4e0 [ib_ipoib]
[ 140.970006]
but task is already holding lock:
[ 140.975141] (&priv->vlan_rwsem){++++}, at: [<ffffffffc0834ee1>] __ipoib_ib_dev_flush+0x51/0x4e0 [ib_ipoib]
[ 140.982105]
which lock already depends on the new lock.
[ 140.990023]
the existing dependency chain (in reverse order) is:
[ 140.998650]
-> #1 (&priv->vlan_rwsem){++++}:
[ 141.005276] down_read+0x4d/0xb0
[ 141.009560] ipoib_open+0xad/0x120 [ib_ipoib]
[ 141.014400] __dev_open+0xcb/0x140
[ 141.017919] __dev_change_flags+0x1a4/0x1e0
[ 141.022133] dev_change_flags+0x23/0x60
[ 141.025695] devinet_ioctl+0x704/0x7d0
[ 141.029156] sock_do_ioctl+0x20/0x50
[ 141.032526] sock_ioctl+0x221/0x300
[ 141.036079] do_vfs_ioctl+0xa6/0x6d0
[ 141.039656] SyS_ioctl+0x74/0x80
[ 141.042811] entry_SYSCALL_64_fastpath+0x1f/0x96
[ 141.046891]
-> #0 (rtnl_mutex){+.+.}:
[ 141.051701] lock_acquire+0xd4/0x220
[ 141.055212] __mutex_lock+0x88/0x970
[ 141.058631] __ipoib_ib_dev_flush+0x2da/0x4e0 [ib_ipoib]
[ 141.063160] __ipoib_ib_dev_flush+0x71/0x4e0 [ib_ipoib]
[ 141.067648] process_one_work+0x1f5/0x610
[ 141.071429] worker_thread+0x4a/0x3f0
[ 141.074890] kthread+0x141/0x180
[ 141.078085] ret_from_fork+0x24/0x30
[ 141.081559]
other info that might help us debug this:
[ 141.088967] Possible unsafe locking scenario:
[ 141.094280] CPU0 CPU1
[ 141.097953] ---- ----
[ 141.101640] lock(&priv->vlan_rwsem);
[ 141.104771] lock(rtnl_mutex);
[ 141.109207] lock(&priv->vlan_rwsem);
[ 141.114032] lock(rtnl_mutex);
[ 141.116800]
*** DEADLOCK ***
Fixes: b4b678b06f ("IB/ipoib: Grab rtnl lock on heavy flush when calling ndo_open/stop")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
memalloc_noio_save modifies the behavior of MM, we must restore it after
we are done.
Fixes: d83187dda9 ("IB/IPoIB: Convert IPoIB to memalloc_noio_* calls")
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaDF9JAAoJELgmozMOVy/dDXUP/i92g+G4OJ+4hHMh4KCjQMHT
eMr/w9l1C033HrtsU1afPhqHOsKSxwCuJSiTgN4uXIm67/2kPK5Vlx+ir7mbOLwB
3ukVK6Q/aFdigWCUhIaJSlDpjbd2sEj7JwKtM3rucvMWJlBJ4mAbcVQVfU96CCsv
V9mO7dpR3QtYWDId9DukfnAfPUPFa3SMZnD7tdl6mKNRg/MjWGYLAL4nJoBfex5f
b4o+MTrbuFWXYsfDru1m9BpHgyul20ldfcnbe8C/sVOQmOgkX7ngD5Sdi1FLeRJP
GF/DnAqInC9N7cAxZHx4kH9x6mLMmEdfnwQ9VTVqGUHBsj3H4hQTVIAFfHUhWUbG
TP5ZHgZG2CewZ0rf092cWlDZwp6n0BalnbQJr+QN4MzPmYbofs3AccSKUwrle+e+
E6yYf4XxJdt7wRr4F1QKygtUEXSnNkNYUDQ4ZFbpJS/D4Sq80R1ZV/WZ7PJxm1D/
EIKoi7NU9cbPMIlbCzn8kzgfjS7Pe4p0WW/Xxc/IYmACzpwNPkZuFGSND79ksIpF
jhHqwZsOWFuXISjvcR4loc8wW6a5w5vjOiX0lLVz0NSdXSzVqav/2at7ZLDx/PT+
Lh9YVL51akA3hiD+3X6iOhfOUu6kskjT9HijE5T8rJnf0V+C6AtIRpwrQ7ONmjJm
3JMrjjLxtCIvpUyzCvDW
=A1oL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a fairly plain pull request. Lots of driver updates across the
stack, a huge number of static analysis cleanups including a close to
50 patch series from Bart Van Assche, and a number of new features
inside the stack such as general CQ moderation support.
Nothing really stands out, but there might be a few conflicts as you
take things in. In particular, the cleanups touched some of the same
lines as the new timer_setup changes.
Everything in this pull request has been through 0day and at least two
days of linux-next (since Stephen doesn't necessarily flag new
errors/warnings until day2). A few more items (about 30 patches) from
Intel and Mellanox showed up on the list on Tuesday. I've excluded
those from this pull request, and I'm sure some of them qualify as
fixes suitable to send any time, but I still have to review them
fully. If they contain mostly fixes and little or no new development,
then I will probably send them through by the end of the week just to
get them out of the way.
There was a break in my acceptance of patches which coincides with the
computer problems I had, and then when I got things mostly back under
control I had a backlog of patches to process, which I did mostly last
Friday and Monday. So there is a larger number of patches processed in
that timeframe than I was striving for.
Summary:
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (296 commits)
RDMA/core: Rename kernel modify_cq to better describe its usage
IB/mlx5: Add CQ moderation capability to query_device
IB/mlx4: Add CQ moderation capability to query_device
IB/uverbs: Add CQ moderation capability to query_device
IB/mlx5: Exposing modify CQ callback to uverbs layer
IB/mlx4: Exposing modify CQ callback to uverbs layer
IB/uverbs: Allow CQ moderation with modify CQ
iw_cxgb4: atomically flush the qp
iw_cxgb4: only call the cq comp_handler when the cq is armed
iw_cxgb4: Fix possible circular dependency locking warning
RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion
IB/core: Only maintain real QPs in the security lists
IB/ocrdma_hw: remove unnecessary code in ocrdma_mbx_dealloc_lkey
RDMA/core: Make function rdma_copy_addr return void
RDMA/vmw_pvrdma: Add shared receive queue support
RDMA/core: avoid uninitialized variable warning in create_udata
RDMA/bnxt_re: synchronize poll_cq and req_notify_cq verbs
RDMA/bnxt_re: Flush CQ notification Work Queue before destroying QP
RDMA/bnxt_re: Set QP state in case of response completion errors
RDMA/bnxt_re: Add memory barriers when processing CQ/EQ entries
...
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
Current ib_modify_cq() is used to set CQ moderation parameters.
This patch renames ib_modify_cq() to be rdma_set_cq_moderation(),
because the kernel version of RDMA API doesn't need to follow already
exposed to user's API pattern (create_XXX/modify_XXX/query_XXX/destroy_XXX)
and better to have more accurate name which describes the actual usage.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The use_srq configfs attribute is created after it is read. Hence
modify srpt_tpg_attrib_use_srq_store() such that this function
switches dynamically between non-SRQ and SRQ mode.
Reported-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce the helper function srpt_set_enabled(). Protect
sport->enabled changes with sdev->mutex. Makes configfs writes
into 'enabled' wait until all channel resources have been freed.
Wait until channel release has finished during kernel module
unload.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Except for changing a BUG_ON() call into a WARN_ON_ONCE() call, this
patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The only functional change in this patch is in the srpt_add_one()
error path: if allocating the ring buffer for the SRQ fails, fall
back to non-SRQ mode instead of disabling SRP target functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
IB and iWARP specs both spell out that posting a receive work request
to a queue pair in the RESET state is an invalid operation and required
to fail. Postpone posting receive work requests until after the
transition to the INIT state.
Fixes: commit dea262094c ("IB/srpt: Change default behavior from using SRQ to using RC")
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
NAPI budget is 64 packets, while maximum polling size for
the send CQ is 16. Let's bring them in sync, so the NAPI
budget will be reused completely.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of explicit call to poll_cq of the tx ring, use the NAPI mechanism
to handle the completions of each packet that has been sent to the HW.
The next major changes were taken:
* The driver init completion function in the creation of the send CQ,
that function triggers the napi scheduling.
* The driver uses CQ for RX for both modes UD and CM, and CQ for TX
for CM and UD.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The first step toward using NAPI in the UD/TX flow is to separate
between two flows, the NAPI and the xmit, meaning no use of shared
variables between both flows.
This patch takes out the tx_outstanding variable that was used in both
flows and instead the driver uses the 2 cyclic ring variables: tx_head
and tx_tail, tx_head used in the xmit flow and tx_tail in the NAPI flow.
Cc: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Conflicts:
drivers/infiniband/hw/cxgb4/cm.c
drivers/infiniband/hw/qib/qib_driver.c
drivers/infiniband/hw/qib/qib_mad.c
There were minor fixups needed in these files. Just minor context diffs
due to patches from independent sources touching the same basic area.
Signed-off-by: Doug Ledford <dledford@redhat.com>
The early for-next branch was based on v4.14-rc2, while the shared pull
request I got from Mellanox used a v4.14-rc4 base. I'm making the
branch that was the shared Mellanox pull request the new for-next branch
and merging the early for-next branch into it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
For small networks it is safe to reduce the subnet timeout from
its default value (18 for opensm) to 16. Make the SRP CM timeout
dependent on the subnet timeout such that decreasing the subnet
timeout also causes SRP failover and failback to occur faster.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This is a micro-optimization for the hot path.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Although in the RC mode more resources are needed that mode has three
advantages over SRQ:
- It works with all RDMA adapters, even those that do not support
SRQ.
- Posting WRs and polling WCs does not trigger lock contention
because only one thread at a time accesses a WR or WC queue in
non-SRQ mode.
- The end-to-end flow control mechanism is used.
>From the IB spec:
C9-150.2.1: For QPs that are not associated with an SRQ, each HCA
receive queue shall generate end-to-end flow control credits. If
a QP is associated with an SRQ, the HCA receive queue shall not
generate end-to-end flow control credits.
Add new configfs attributes that allow to configure which mode to use
(/sys/kernel/config/target/srpt/$GUID/$GUID/attrib/use_srq). Note:
only the attribute for port 1 is relevant on multi-port adapters.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch is a micro-optimization for the hot path.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Make srpt_parse_i_port_id() return a negative value if hex2bin()
fails.
Fixes: commit a42d985bd5 ("ib_srpt: Initial SRP Target merge for v3.3-rc1")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Avoid that gcc 7 reports the following warning when building with W=1:
warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To support passing child interfaces to the lower device a new
rdma_netdev function was used, set_id. This will allow us to
attach the PKEY index lower device resources such as TIS/QP.
For devices that do not support offloads in IPoIB same logic
will be used, setting the PKEY index to priv struct.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Instead of making every caller convert the second argument of
sa_path_set_slid() and sa_path_set_dlid() to big endian format,
make these two functions accept LIDs in CPU endian format.
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Cc: Don Hiatt <don.hiatt@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Alex Vesker <valex@mellanox.com>
Cc: Erez Shitrit <erezsh@mellanox.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Cc: linux-rdma@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add protocol specific routing control information in the encapsulation
header as per the configuration.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Scott Franco <safranco@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update eth_link_status and operating status information to
represent the overall status of the virtual Ethernet switch port.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Clear the MAC table digest when the MAC table is freed.
Reviewed-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Scott Franco <safranco@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Do not include EM specified MAC address in total MACs of the
UC MAC list.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set power on default value of 1500 for eth_mtu.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Per pcp mtu fields are not used, mark them as reserved.
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
commit 9a9b811269 will cause core to fail UD QP from being destroyed
on ipoib unload, therefore cause resources leakage.
On pkey change event above patch modifies mgid before calling underlying
driver to detach it from QP. Drivers' detach_mcast() will fail to find
modified mgid it was never given to attach in a first place.
Core qp->usecnt will never go down, so ib_destroy_qp() will fail.
IPoIB driver actually does take care of new broadcast mgid based on new
pkey by destroying an old mcast object in ipoib_mcast_dev_flush())
....
if (priv->broadcast) {
rb_erase(&priv->broadcast->rb_node, &priv->multicast_tree);
list_add_tail(&priv->broadcast->list, &remove_list);
priv->broadcast = NULL;
}
...
then in restarted ipoib_macst_join_task() creating a new broadcast mcast
object, sending join request and on completion tells the driver to attach
to reinitialized QP:
...
if (!priv->broadcast) {
...
broadcast = ipoib_mcast_alloc(dev, 0);
...
memcpy(broadcast->mcmember.mgid.raw, priv->dev->broadcast + 4,
sizeof (union ib_gid));
priv->broadcast = broadcast;
...
Fixes: 9a9b811269 ("IB/ipoib: Update broadcast object if PKey value was changed in index 0")
Cc: stable@vger.kernel.org
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Call ipoib_remove_one when one of the IPoIB ports fails to initialize in
order not to leave the module in unstable state.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
No reason to have dependency on PCI for the entire infiniband stack so
move it to KConfig of only the drivers that actually using PCI.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Call free_rdma_netdev instead of free_netdev each time we want to
release a netdevice. This call is also relevant for future freeing
of offloaded child interfaces.
This patch also adds a missing call for free netdevice when releasing
a parent interface that has child interfaces using ipoib_remove_one.
Fixes: cd565b4b51 ('IB/IPoIB: Support acceleration options callbacks')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A possible ABBA lock can happen with RTNL and vlan_rwsem.
For example:
Flow A: Device Flush
__ipoib_ib_dev_flush
down_read(vlan_rwsem) // Lock A
ipoib_flush_ah
flush_workqueue(priv->wq) // Wait for completion
A work on shared WQ (Mcast carrier)
ipoib_mcast_carrier_on_task
while (!rtnl_trylock()) // Wait for lock B
Flow B: Sysfs PKEY delete
ipoib_vlan_delete
lock(RTNL) // Lock B
down_write(vlan_rwsem) // Wait for lock A
This can happen with PKEY creates as well. The solution is to release
the RTNL lock in sysfs functions in case it is not possible to lock
VLAN RW semaphore and reset the SYS call.
Fixes: 69956d8326 ("IB/ipoib: Sync between remove_one to sysfs calls that use rtnl_lock")
Signed-off-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ib_mr->length represents the length of the MR in bytes as per
the IBTA spec 1.3 section 11.2.10.3 (REGISTER PHYSICAL MEMORY REGION).
Currently ib_mr->length field is defined as only 32-bits field.
This might result into truncation and failed WRs of consumers who
registers more than 4GB bytes memory regions and whose WRs accessing
such MRs.
This patch makes the length 64-bit to avoid such truncation.
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Faisal Latif <faisal.latif@intel.com>
Fixes: 4c67e2bfc8 ("IB/core: Introduce new fast registration API")
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sagi Grimberg
Bart Van Assche
Erez Shitrit
Alex Vesker
Yuval Shaia
Linus Torvalds
Leon Romanovsky
Mike Marciniszyn
David S. Miller
Greg Kroah-Hartman
Kees Cook
Doug Ledford
Ajaykumar Hotchandani
Niranjana Vishwanathapura
Scott Franco
Alex Estrin
Shalom Lagziel
Parav Pandit