Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus an Intel RAPL PMU driver fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tests x86: Fix stack map lookup in dwarf unwind test
perf x86: Fix perf to use non-executable stack, again
perf tools: Remove extra '/' character in events file path
perf machine: Search for modules in %s/lib/modules/%s
perf tests: Add static build make test
perf tools: Fix bfd dependency libraries detection
perf tools: Use LDFLAGS instead of ALL_LDFLAGS
perf/x86: Fix RAPL rdmsrl_safe() usage
tools lib traceevent: Fix memory leak in pretty_print()
tools lib traceevent: Fix backward compatibility macros for pevent filter enums
perf tools: Disable libdw unwind for all but x86 arch
perf tests x86: Fix memory leak in sample_ustack()
The AND instruction is erroneously using the X register instead
of the K register.
Signed-off-by: Brendan Hickey <bhickey@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arch/x86/tests/regs_load.S is missing the linker note about the stack
requirements, therefore making the linker fall back to an executable
stack. As this object gets linked against the final perf binary, it'll
needlessly end up with an executable stack. Fix this by adding the
appropriate linker note.
Also add a global linker flag to prevent future regressions, as
suggested by Jiri. This way perf won't get an executable stack even if
we fail to add the .GNU-stack linker note to future assembler files.
Though, doing so might create regressions the other way around, when
(statically) linking against libraries needing an executable stack.
But, apparently, regressing in that direction is wanted as it is an
indicator of poor code quality -- or just missing linker notes.
Fixes: 3c8b06f981 ("perf tests x86: Introduce perf_regs_load function")
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1398617466-22749-1-git-send-email-minipli@googlemail.com
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
The array debugfs_known_mountpoints[] will cause extra '/'
character output.
Remove it.
pre:
$ perf probe -l
/sys/kernel/debug//tracing/uprobe_events file does not exist -
please rebuild kernel with CONFIG_UPROBE_EVENTS.
post:
$ perf probe -l
/sys/kernel/debug/tracing/uprobe_events file does not exist -
please rebuild kernel with CONFIG_UPROBE_EVENTS.
Signed-off-by: Xia Kaixu <xiakaixu@huawei.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/535B6660.2060001@huawei.com
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Modules installed outside of the kernel's build system should go into
"%s/lib/modules/%s/extra", but at present, perf will only look at them
when they are in "%s/lib/modules/%s/kernel". Lets encourage good
citizenship by relaxing this requirement to "%s/lib/modules/%s". This
way open source modules that are out-of-tree have no incentive to start
populating a directory reserved for in-kernel modules and I can stop
hex-editing my system's perf binary when profiling OSS out-of-tree
modules.
Feedback from Namhyung Kim correctly revealed that the hex-edits that I
had been doing meant that perf was also traversing the build and source
symlinks in %s/lib/modules/%s. That is undesireable, so we explicitly
exclude them from traversal with a minor tweak to the traversal routine.
Signed-off-by: Richard Yao <ryao@gentoo.org>
Acked-by: Namhyung kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1398532675-13684-1-git-send-email-ryao@gentoo.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Adding test for building static perf build into the automated
suite. Also available via following commands:
$ make -f tests/make make_static
- make_static: cd . && make -f Makefile DESTDIR=/tmp/tmp.7u5MlB4njo LDFLAGS=-static
$ make -f tests/make make_static_O
- make_static_O: cd . && make -f Makefile O=/tmp/tmp.Ay6r3wEmtX DESTDIR=/tmp/tmp.vK0KQwO0Vi LDFLAGS=-static
Acked-by: David Ahern <dsahern@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1398760413-7574-1-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
There's false assumption in the library detection code
assuming -liberty and -lz are always present once bfd
is detected. The fails on Ubuntu (14.04) as reported
by Ingo.
Forcing the bdf dependency libraries detection any
time bfd library is detected.
Reported-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Ingo Molnar <mingo@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1398676935-6615-1-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
We no longer use ALL_LDFLAGS, Replacing with LDFLAGS.
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1398675770-3109-1-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Commit 12e55569a2 "tools lib traceevent: Use helper trace-seq in print
functions like kernel does" added a extra trace_seq helper to process
string arguments like the kernel does it. But the difference between the
kernel and the userspace library is that the kernel's trace_seq structure
has a static allocated buffer. The userspace one has a dynamically
allocated one. It requires a trace_seq_destroy(), otherwise it produces
a nasty memory leak.
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140422192330.6bb09bf8@gandalf.local.home
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The return value for pevent_filter_match() is suppose to return FILTER_NONE
if the event doesn't have a filter, and FILTER_NOEXIST if there is no filter
at all. But the change 41e12e580a "tools lib traceevent: Refactor
pevent_filter_match() to get rid of die()" replaced the return value
with PEVENT_ERRNO__* values and added "backward compatibility" macros
that used the old names. Unfortunately, the NOEXIST and NONE macros were
swapped, and this broke users that use the old return names.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20140421222346.0351ced4@gandalf.local.home
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
So far there's only x86 libdw unwind support merged in perf.
Disable it on all other architectures in case libdw unwind
support is detected in system.
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Corey Ashford <cjashfor@linux.vnet.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jean Pihet <jean.pihet@linaro.org>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1397988006-14158-1-git-send-email-jolsa@redhat.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
- bindir is created, but sbindir is used -> fix that
- the debug parts are there twice (copy paste bug?). Remove one of the
exact same parts
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In the current version, when using perf record, if something goes
wrong in tools/perf/builtin-record.c:375
session = perf_session__new(file, false, NULL);
The error message:
"Not enough memory for reading per file header"
is issued. This error message seems to be outdated and is not very
helpful. This patch proposes to replace this error message by
"Perf session creation failed"
I believe this issue has been brought to lkml:
https://lkml.org/lkml/2014/2/24/458
although this patch only tackles a (small) part of the issue.
Additionnaly, this patch improves error reporting in
tools/perf/util/data.c open_file_write.
Currently, if the call to open fails, the user is unaware of it.
This patch logs the error, before returning the error code to
the caller.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Adrien BAK <adrien.bak@metascale.org>
Link: http://lkml.kernel.org/r/1397786443.3093.4.camel@beast
[ Reorganize the changelog into paragraphs ]
[ Added empty line after fd declaration in open_file_write ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
pert-report doesn't resolve function names in VDSO:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
0x7fff6b1fe861
__gettimeofday
ACE_OS::gettimeofday()
...
In this case symbol values should be adjusted the same way as for executables,
relocatable objects and prelinked libraries.
After fix:
$ perf report --stdio -g flat,0.0,15,callee --sort pid
...
8.76%
__vdso_gettimeofday
__gettimeofday
ACE_OS::gettimeofday()
Signed-off-by: Vladimir Nikulichev <nvs@tbricks.com>
Tested-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/969812.163009436-sendEmail@nvs
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Every event in the perf-kvm has a 'stats' structure, which contains
max/min/average/etc times of handling this event.
The problem is that the 'perf-kvm stat report' command always shows
that 'min time' is 0us for every event. Example:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 0us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 0us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 0us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 0us 44us 16.49us ( +- 38.20% )
[..]
This happens because the 'stats' structure is not initialized and
stats->min equals to 0. Lets initialize the structure for every
event after its allocation using init_stats() function. This initializes
stats->min to -1 and makes 'Min time' statistics counting work:
# perf kvm stat report
Analyze events for all VCPUs:
VM-EXIT Samples Samples% Time% Min Time Max Time Avg time
[..]
0xB2 MSCH 12 0.07% 0.00% 6us 8us 7.31us ( +- 2.11% )
0xB2 CHSC 12 0.07% 0.00% 7us 18us 9.39us ( +- 9.49% )
0xB2 STPX 8 0.05% 0.00% 1us 2us 1.88us ( +- 7.18% )
0xB2 STSI 7 0.04% 0.00% 1us 44us 16.49us ( +- 38.20% )
[..]
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1397053319-2130-3-git-send-email-borntraeger@de.ibm.com
[ Fixing the perf examples changelog output ]
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Here are a few driver fixes for char/misc drivers that resolve reported
issues.
All have been in linux-next successfully for a few days.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRlx4ACgkQMUfUDdst+ylYCgCdHm8SDiXwRfhUQJcYYlXrI1xs
skwAn3p1ydnIyVZJ/B3uxTA/0/1Jof5Z
=no/7
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few driver fixes for char/misc drivers that resolve
reported issues.
All have been in linux-next successfully for a few days"
* tag 'char-misc-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: Negotiate version 3.0 when running on ws2012r2 hosts
Tools: hv: Handle the case when the target file exists correctly
vme_tsi148: Utilize to_pci_dev() macro
vme_tsi148: Fix PCI address mapping assumption
vme_tsi148: Fix typo in tsi148_slave_get()
w1: avoid recursive device_add
w1: fix netlink refcnt leak on error path
misc: Grammar s/addition/additional/
drivers: mcb: fix memory leak in chameleon_parse_cells() error path
mei: ignore client writing state during cb completion
mei: me: do not load the driver if the FW doesn't support MEI interface
GenWQE: Increase driver version number
GenWQE: Fix multithreading problems
GenWQE: Ensure rc is not returning an uninitialized value
GenWQE: Add wmb before DDCB is started
GenWQE: Enable access to VPD flash area
Pull perf fixes from Ingo Molnar:
"Tooling fixes, plus a simple hardware-enablement patch for the Intel
RAPL PMU (energy use measurement) on Haswell CPUs, which I hope is
still fine at this stage"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Instead of redirecting flex output, use -o
perf tools: Fix double free in perf test 21 (code-reading.c)
perf stat: Initialize statistics correctly
perf bench: Set more defaults in the 'numa' suite
perf bench: Fix segfault at the end of an 'all' execution
perf bench: Update manpage to mention numa and futex
perf probe: Use dwarf_getcfi_elf() instead of dwarf_getcfi()
perf probe: Fix to handle errors in line_range searching
perf probe: Fix --line option behavior
perf tools: Pick up libdw without explicit LIBDW_DIR
MAINTAINERS: Change e-mail to kernel.org one
perf callchains: Disable unwind libraries when libelf isn't found
tools lib traceevent: Do not call warning() directly
tools lib traceevent: Print event name when show warning if possible
perf top: Fix documentation of invalid -s option
perf/x86: Enable DRAM RAPL support on Intel Haswell
Return the appropriate error code and handle the case when the target
file exists correctly. This fixes a bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.14]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
perf_evlist__delete() deletes attached cpu and thread maps
but the test is still using them, so remove them from the
evlist before deleting it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/r/53465E3E.8070201@intel.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Pull liblockdep fixes from Sasha Levin:
" 1. There was a build breakage caused by marking a function 'asmlinkage'
in lockdep.h. Fix that by ignoring asmlinkage and visible annotations.
2. Josh Boyer mentioned that Fedora would like to include liblockdep
as a package, so we had to fix our versioning methods from being dumb
and pointless to something actually usable. So now liblockdep.so tracks
the kernel version which makes lives of distro folks much easier. "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf stat did initialize the stats structure used to compute
stddev etc. incorrectly. It merely zeroes it. But one member
(min) needs to be set to a non zero value. This causes min
to be not computed at all. Call init_stats() correctly.
It doesn't matter for stat currently because it doesn't use
min, but it's still better to do it correctly.
The other users of statistics are already correct.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1395768699-16060-1-git-send-email-andi@firstfloor.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Currently,
$ perf bench numa mem
errors out with usage information. To make this more user-friendly, let
us provide a minimum set of default values required for a test
run. As an added bonus,
$ perf bench all
now goes all the way to completion.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-2-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
At the end of
$ perf bench all
the program segfaults because it attempts to dereference a NULL
pointer. Fix this fault.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395964219-22173-4-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The dwarf_getcfi() only checks .debug_frame section for CFI, but as
most binaries only have .eh_frame it'd return NULL and it makes
some variables inaccessible.
Using dwarf_getcfi_elf (along with dwarf_getelf()) allows to show and
add probe to more variables.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1396854348-9296-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
As Namhyung reported(https://lkml.org/lkml/2014/4/1/89),
current perf-probe -L option doesn't handle errors in line-range
searching correctly. It causes a SEGV if an error occured in the
line-range searching.
----
$ perf probe -x ./perf -v -L map__load
Open Debuginfo file: /home/namhyung/project/linux/tools/perf/perf
fname: util/map.c, lineno:153
New line range: 153 to 2147483647
path: (null)
Segmentation fault (core dumped)
----
This is because line_range_inline_cb() ignores errors
from find_line_range_by_line() which means that lr->path is
already freed on the error path in find_line_range_by_line().
As a result, get_real_path() accesses the lr->path and it
causes a NULL pointer exception.
This fixes line_range_inline_cb() to handle the error correctly,
and report it to the caller.
Anyway, this just fixes a possible SEGV bug, Namhyung's patch
is also required.
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20140402054831.19080.27006.stgit@ltc230.yrl.intra.hitachi.co.jp
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The commit 5a62257a3d ("perf probe: Replace line_list with
intlist") replaced line_list to intlist but it has a problem that if a
same line was added again, it'd return -EEXIST rather than 1.
Since line_range_walk_cb() only checks the result being negative, it
resulted in failure or segfault sometimes.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/1396327677-3657-1-git-send-email-namhyung@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The Makefile logic sets FEATURE_CHECKS_CFLAGS-libdw-dwarf-unwind and
FEATURE_CHECKS_LDFLAGS-libdw-dwarf-unwind only if LIBDW_DIR is
defined. This means that under a normal setup,
$ make NO_LIBUNWIND=1
won't automatically pick up libdw. Fix this.
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Acked-by: Jean Pihet <jean.pihet@linaro.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1395873845-466-1-git-send-email-artagnon@gmail.com
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
I.e. do the same as when NO_LIBELF is explicitely passed in the 'make'
command line, fixing this:
Auto-detecting system features:
... dwarf: [ OFF ]
... glibc: [ on ]
... gtk2: [ OFF ]
... libaudit: [ OFF ]
... libbfd: [ OFF ]
... libelf: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... DWARF post unwind library: libdw
<SNIP>
CC /tmp/build/perf/util/symbol-minimal.o
CC /tmp/build/perf/util/unwind-libdw.o
arch/x86/util/unwind-libdw.c:1:30: fatal error: elfutils/libdwfl.h: No such file or directory
compilation terminated.
CC /tmp/build/perf/tests/keep-tracking.o
util/unwind-libdw.c:2:28: fatal error: elfutils/libdw.h: No such file or directory
compilation terminated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-e39j1yxanltjx4t0msse63ax@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
The patch 3a3ffa2e82 ("tools lib traceevent: Report better error
message on bad function args") added the error message but it seems
there's no reason to call warning() directly.
So change it to do_warning_event() to provide event information too.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1395192174-26273-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
It's sometimes useful to know where the parse failure was occurred. Add
do_warning_event() macro to see the failing event.
It now shows the messages like below:
$ perf test 5
5: parse events tests : Warning: [kvmmmu:kvm_mmu_get_page] bad op token {
Warning: [kvmmmu:kvm_mmu_sync_page] bad op token {
Warning: [kvmmmu:kvm_mmu_unsync_page] bad op token {
Warning: [kvmmmu:kvm_mmu_prepare_zap_page] bad op token {
Warning: [kvmmmu:fast_page_fault] function is_writable_pte not defined
Warning: [xen:xen_mmu_ptep_modify_prot_commit] function sizeof not defined
Warning: [xen:xen_mmu_ptep_modify_prot_start] function sizeof not defined
Warning: [xen:xen_mmu_set_pgd] function sizeof not defined
Warning: [xen:xen_mmu_set_pud] function sizeof not defined
Warning: [xen:xen_mmu_set_pmd] function sizeof not defined
...
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ramkumar Ramachandra <artagnon@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1395192174-26273-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
On perf top, the -s option is used for --sort, but the man page
contains invalid documentation of -s option for --sym-annotate.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung.kim@lge.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1395193578-27098-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
Pull intel_idle and turbostat material for v3.15-rc1 from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_idle: fine-tune IVT residency targets
tools/power turbostat: Run on Broadwell
tools/power turbostat: simplify output, add Avg_MHz
intel_idle: Add CPU model 54 (Atom N2000 series)
intel_idle: support Bay Trail
intel_idle: allow sparse sub-state numbering, for Bay Trail
ACPI idle: permit sparse C-state sub-state numbers
After this patch 'page-types' can walk over a file's mappings and
analyze populated page cache pages mostly without disturbing its state.
It maps chunk of file, marks VMA as MADV_RANDOM to turn off readahead,
pokes VMA via mincore() to determine cached pages, triggers page-fault
only for them, and finally gathers information via pagemap/kpageflags.
Before unmap it marks VMA as MADV_SEQUENTIAL for ignoring reference
bits.
usage: page-types -f <path>
If <path> is directory it will analyse all files in all subdirectories.
Symlinks are not followed as well as mount points. Hardlinks aren't
handled, they'll be dumped as many times as they are found. Recursive
walk brings all dentries into dcache and populates page cache of
block-devices aka 'Buffers'.
Probably it's worth to add ioctl for dumping file page cache as array of
PFNs as a replacement for this hackish juggling with
mmap/madvise/mincore/pagemap. Also recursive walk could be replaced
with dumping cached inodes via some ioctl or debugfs interface followed
by openning them via open_by_handle_at, this would fix hardlinks
handling and unneeded population of dcache and buffers. This interface
might be used as data source for constructing readahead plans and for
background optimizations of actively used files.
collateral changes:
+ fix 64-bit LFS: define _FILE_OFFSET_BITS instead of _LARGEFILE64_SOURCE
+ replace lseek + read with single pread
+ make show_page_range() reusable after flush
usage example:
~/src/linux/tools/vm$ sudo ./page-types -L -f page-types
foffset offset flags
page-types Inode: 2229277 Size: 89065 (22 pages)
Modify: Tue Feb 25 12:00:59 2014 (162 seconds ago)
Access: Tue Feb 25 12:01:00 2014 (161 seconds ago)
0 3cbf3b __RU_lA____M________________________
1 38946a __RU_lA____M________________________
2 1a3cec __RU_lA____M________________________
3 1a8321 __RU_lA____M________________________
4 3af7cc __RU_lA____M________________________
5 1ed532 __RU_lA_____________________________
6 2e436a __RU_lA_____________________________
7 29a35e ___U_lA_____________________________
8 2de86e ___U_lA_____________________________
9 3bdfb4 ___U_lA_____________________________
10 3cd8a3 ___U_lA_____________________________
11 2afa50 ___U_lA_____________________________
12 2534c2 ___U_lA_____________________________
13 1b7a40 ___U_lA_____________________________
14 17b0be ___U_lA_____________________________
15 392b0c ___U_lA_____________________________
16 3ba46a __RU_lA_____________________________
17 397dc8 ___U_lA_____________________________
18 1f2a36 ___U_lA_____________________________
19 21fd30 __RU_lA_____________________________
20 2c35ba __RU_l______________________________
21 20f181 __RU_l______________________________
flags page-count MB symbolic-flags long-symbolic-flags
0x000000000000002c 2 0 __RU_l______________________________ referenced,uptodate,lru
0x0000000000000068 11 0 ___U_lA_____________________________ uptodate,lru,active
0x000000000000006c 4 0 __RU_lA_____________________________ referenced,uptodate,lru,active
0x000000000000086c 5 0 __RU_lA____M________________________ referenced,uptodate,lru,active,mmap
total 22 0
~/src/linux/tools/vm$ sudo ./page-types -f /
flags page-count MB symbolic-flags long-symbolic-flags
0x0000000000000028 21761 85 ___U_l______________________________ uptodate,lru
0x000000000000002c 127279 497 __RU_l______________________________ referenced,uptodate,lru
0x0000000000000068 74160 289 ___U_lA_____________________________ uptodate,lru,active
0x000000000000006c 84469 329 __RU_lA_____________________________ referenced,uptodate,lru,active
0x000000000000007c 1 0 __RUDlA_____________________________ referenced,uptodate,dirty,lru,active
0x0000000000000228 370 1 ___U_l___I__________________________ uptodate,lru,reclaim
0x0000000000000828 49 0 ___U_l_____M________________________ uptodate,lru,mmap
0x000000000000082c 126 0 __RU_l_____M________________________ referenced,uptodate,lru,mmap
0x0000000000000868 137 0 ___U_lA____M________________________ uptodate,lru,active,mmap
0x000000000000086c 12890 50 __RU_lA____M________________________ referenced,uptodate,lru,active,mmap
total 321242 1254
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arch/tile updates from Chris Metcalf:
"These fix a few stray build issues seen in linux-next, and also add
the minimal required support for perf to tilegx"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: remove unused variable 'devcap'
tile: Fix vDSO compilation issue with allyesconfig
perf tools: Allow building for tile
tile/perf: Support perf_events on tilegx and tilepro
tile: Enable NMIs on return from handle_nmi() without errors
tile: Add support for handling PMC hardware
tile: don't use __get_cpu_var() with structure-typed arguments
tile: avoid overflow in ns2cycles
CLOSE_CONSOLE_SIGNAL to the kvm.conf file, as the kvm guest requires
a different signal than a normal console uses.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTOuRXAAoJEKQekfcNnQGuukQH/3x8/rCkDSfn44zdA0srumm6
1yKfn3QBgspoxi78zypPLiCmSKLMVWpKOfFwyN3jaQSy7/UfoSTLEEPKcKIEdaUe
2HWMIO2OxToghRfo1WSA899p0MPtw44J7gy6bvLv9qMl8yyNE9KBotEQTT2vJ+ya
ODMXNhy4lmRvz3jHFLu4Z62PsJ/YQvHzehgb1N62EkwvBwtaCu8CAt1qvN5B9EnO
wWCYJ+DfdnXwNhA+e7w4hOTxc8thO4bRXFKVs50ST7zMHWNtTxs+WODlmJKQGUUS
SNeZcwkh/BBdM9MYIQQUpqUQ16lEh7/6fVdFMHpCK2IL32T0wNwpFf3A+ZTnRoo=
=b4GL
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull single ktest fix from Steven Rostedt:
"This just contains a single update by Satoru Takeuchi, which adds
CLOSE_CONSOLE_SIGNAL to the kvm.conf file, as the kvm guest requires a
different signal than a normal console uses"
* tag 'ktest-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Set CLOSE_CONSOLE_SIGNAL in the kvm.conf
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
doubling of the default queue length though.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=AoMS
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing exciting: virtio-blk users might see a bit of a boost from the
doubling of the default queue length though"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-blk: base queue-depth on virtqueue ringsize or module param
Revert a02bbb1ccf: MAINTAINERS: add virtio-dev ML for virtio
virtio: fail adding buffer on broken queues.
virtio-rng: don't crash if virtqueue is broken.
virtio_balloon: don't crash if virtqueue is broken.
virtio_blk: don't crash, report error if virtqueue is broken.
virtio_net: don't crash if virtqueue is broken.
virtio_balloon: don't softlockup on huge balloon changes.
virtio: Use pci_enable_msix_exact() instead of pci_enable_msix()
MAINTAINERS: virtio-dev is subscribers only
tools/virtio: add a missing )
tools/virtio: fix missing kmemleak_ignore symbol
tools/virtio: update internal copies of headers
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
