From: Dmitry Butskoy <dmitry@butskoy.name>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=8747
Problem Description:
It is related to the possibility to obtain MSG_ERRQUEUE messages from the udp
and raw sockets, both connected and unconnected.
There is a little typo in net/ipv6/icmp.c code, which prevents such messages
to be delivered to the errqueue of the correspond raw socket, when the socket
is CONNECTED. The typo is due to swap of local/remote addresses.
Consider __raw_v6_lookup() function from net/ipv6/raw.c. When a raw socket is
looked up usual way, it is something like:
sk = __raw_v6_lookup(sk, nexthdr, daddr, saddr, IP6CB(skb)->iif);
where "daddr" is a destination address of the incoming packet (IOW our local
address), "saddr" is a source address of the incoming packet (the remote end).
But when the raw socket is looked up for some icmp error report, in
net/ipv6/icmp.c:icmpv6_notify() , daddr/saddr are obtained from the echoed
fragment of the "bad" packet, i.e. "daddr" is the original destination
address of that packet, "saddr" is our local address. Hence, for
icmpv6_notify() must use "saddr, daddr" in its arguments, not "daddr, saddr"
...
Steps to reproduce:
Create some raw socket, connect it to an address, and cause some error
situation: f.e. set ttl=1 where the remote address is more than 1 hop to reach.
Set IPV6_RECVERR .
Then send something and wait for the error (f.e. poll() with POLLERR|POLLIN).
You should receive "time exceeded" icmp message (because of "ttl=1"), but the
socket do not receive it.
If you do not connect your raw socket, you will receive MSG_ERRQUEUE
successfully. (The reason is that for unconnected socket there are no actual
checks for local/remote addresses).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove two unnecessary EXPORT_SYMBOLs and move the
nf_conntrack_l3proto_ipv4 declaration to the correct file.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lower ip6tables, arptables and ebtables printk severity similar to
Dan Aloni's patch for iptables.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_ct_get_tuple() requires the offset to transport header and that bothers
callers such as icmp[v6] l4proto modules. This introduces new function
to simplify them.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The icmp[v6] l4proto modules parse headers in ICMP[v6] error to get tuple.
But they have to find the offset to transport protocol header before that.
Their processings are almost same as prepare() of l3proto modules.
This makes prepare() more generic to simplify icmp[v6] l4proto module
later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all initialized struct seq_operations in net/ const
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch removes the unneeded pointer idev returned from
__in6_dev_get(), which is never used. The check for NULL can be simply
done by if (__in6_dev_get(dev) == NULL).
Signed-off-by: Micah Gruber <micah.gruber@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because reversing RH0 is no longer supported by deprecation
of RH0, let's make IPV6_{RECV,2292}RTHDR boolean options.
Boolean are more appropriate from standard POV.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on <draft-ietf-ipv6-deprecate-rh0-00.txt>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "fix" for emerging security threat was overkill and it broke
basic semantic of IPv6 routing header processing. We should assume
RT0 (or even RT2, depends on configuration) as "unknown" RH type so
that we
- silently ignore the routing header if segleft == 0
- send ICMPv6 Parameter Problem message back to the sender,
otherwise.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DEBUGP to pr_debug and fix lots of non-compiling debug statements.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass NULL, this also doesn't seem very useful for modules.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now memory space for help and NAT are allocated by extension
infrastructure.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TRACE target can be used to follow IP and IPv6 packets through
the ruleset.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick NcHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes redundant parentheses and braces (And add one pair in a
xt_tcpudp.c macro).
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make a number of variables const and/or remove unneeded casts.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of target checkentry functions to boolean.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of match functions to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the return type of match functions to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the "hotdrop" variables to boolean
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
It is clean-up for XFRM type modules and adds aliases with its
protocol:
ESP, AH, IPCOMP, IPIP and IPv6 for IPsec
ROUTING and DSTOPTS for MIPv6
It is almost the same thing as XFRM mode alias, but it is added
new defines XFRM_PROTO_XXX for preprocessing since some protocols
are defined as enum.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Acked-by: Ingo Oeser <netdev@axxeo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes MIPv6 loadable module named "mip6".
Here is a modprobe.conf(5) example to load it automatically
when user application uses XFRM state for MIPv6:
alias xfrm-type-10-43 mip6
alias xfrm-type-10-60 mip6
Some MIPv6 feature is not included by this modular, however,
it should not be affected to other features like either IPsec
or IPv6 with and without the patch.
We may discuss XFRM, MH (RAW socket) and ancillary data/sockopt
separately for future work.
Loadable features:
* MH receiving check (to send ICMP error back)
* RO header parsing and building (i.e. RH2 and HAO in DSTOPTS)
* XFRM policy/state database handling for RO
These are NOT covered as loadable:
* Home Address flags and its rule on source address selection
* XFRM sub policy (depends on its own kernel option)
* XFRM functions to receive RO as IPv6 extension header
* MH sending/receiving through raw socket if user application
opens it (since raw socket allows to do so)
* RH2 sending as ancillary data
* RH2 operation with setsockopt(2)
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill unnecessary CONFIG_IPV6_MIP6.
o It is redundant for RAW socket to keep MH out with the config then
it can handle any protocol.
o Clean-up at AH.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing). This causes DAD and RS
packets to be sent from the slave. These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).
This patch alters the behavior so that addrconf will only run on
the master device itself. I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master. This is consistent with the IPv4 behavior for bonding.
This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.
The eql driver also uses the IFF_SLAVE flag. I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug reported by Haruhito Watanabe <haruhito@sfc.keio.ac.jp>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch that added ipv6_hwtype is broken on tuntap tunnels.
Indeed, it's broken on any device that does not pass the ipv6_hwtype
test.
The reason is that the original test only applies to autoconfiguration,
not IPv6 support. IPv6 support is allowed on any device. In fact,
even with the ipv6_hwtype patch applied you can still add IPv6 addresses
to any interface that doesn't pass thw ipv6_hwtype test provided that
they have a sufficiently large MTU. This is a serious problem because
come deregistration time these devices won't be cleaned up properly.
I've gone back and looked at the rationale for the patch. It appears
that the real problem is that we were creating IPv6 devices even if the
MTU was too small. So here's a patch which fixes that and reverts the
ipv6_hwtype stuff.
Thanks to Kanru Chen for reporting this issue.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts changesets:
6aaf47fa48b7b5f487abde34ed91c4fc038410b4
There are still some correctness issues recently
discovered which do not have a known fix that doesn't
involve doing a full hash table scan on port bind.
So revert for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a helper module is unloaded all conntracks refering to it have their
helper pointer NULLed out, leading to lots of races. In most places this
can be fixed by proper use of RCU (they do already check for != NULL,
but in a racy way), additionally nf_conntrack_expect_related needs to
bail out when no helper is present.
Also remove two paranoid BUG_ONs in nf_conntrack_proto_gre that are racy
and not worth fixing.
Signed-off-by: Patrick McHarrdy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent gcc versions emit warnings when unsigned variables are
compared < 0 or >= 0.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_fib.c: In function ‘fib6_add_rt2node’:
net/ipv6/ip6_fib.c:661: warning: label ‘out’ defined but not used
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to handle ::/0 routes specially any longer.
This should fix BUG #8349.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Yuji Sekiya <sekiya@wide.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IPSEC rule resolution behavior we have does not work for a
lot of people, even though technically it's an improvement from the
-EAGAIN buisness we had before.
Right now we'll block until the key manager resolves the route. That
works for simple cases, but many folks would rather packets get
silently dropped until the key manager resolves the IPSEC rules.
We can't tell these folks to "set the socket non-blocking" because
they don't have control over the non-block setting of things like the
sockets used to resolve DNS deep inside of the resolver libraries in
libc.
With that in mind I coded up the patch below with some help from
Herbert Xu which provides packet-drop behavior during larval state
resolution, controllable via sysctl and off by default.
This lays the framework to either:
1) Make this default at some point or...
2) Move this logic into xfrm{4,6}_policy.c and implement the
ARP-like resolution queue we've all been dreaming of.
The idea would be to queue packets to the policy, then
once the larval state is resolved by the key manager we
re-resolve the route and push the packets out. The
packets would timeout if the rule didn't get resolved
in a certain amount of time.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reverse the sense of the promiscuous-mode tests in ip6_mc_input().
Signed-off-by: Corey Mutter <crm-netdev@mutternet.com>
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move arp_tables initial table structure definitions to arp_tables.h
similar to ip_tables and ip6_tables
- use C99 initializers
- use initializer macros where possible
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
__udp_lib_port_inuse() cannot make direct references to
inet_sk(sk)->rcv_saddr as that is ipv4 specific state and
this code is used by ipv6 too.
Use an operations vector to solve this, and this also paves
the way for ipv6 support for non-wild saddr hashing in UDP.
Signed-off-by: David S. Miller <davem@davemloft.net>
I think this is less critical, but is also suitable for -stable
release.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because skb->dst is assigned in ip6_route_input(), it is really
bad to use it in hop-by-hop option handler(s).
Closes: Bug #8450 (Eric Sesterhenn <snakebyte@gmx.de>)
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an IPv6 router is forwarding a packet with a link-local scope source
address off-link, RFC 4007 requires it to send an ICMPv6 destination
unreachable with code 2 ("not neighbor"), but Linux doesn't. Fix below.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
Dmitry Butskoy