Commit Graph

82 Commits

Author SHA1 Message Date
Ondrej Zary 57e5568fda sata_via: Implement hotplug for VT6421
Enable IRQ on hotplug and add an interrupt handler to handle it.

This allows hotplug to work:
ata5: exception Emask 0x10 SAct 0x0 SErr 0x70000 action 0xe frozen
ata5: SError: { PHYRdyChg PHYInt CommWake }
ata5: hard resetting link
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata5.00: LPM support broken, forcing max_power
ata5.00: ATA-7: WDC WD800JD-75MSA3, 10.01E04, max UDMA/133
ata5.00: 156250000 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata5.00: LPM support broken, forcing max_power
ata5.00: configured for UDMA/133
ata5: EH complete
scsi 4:0:0:0: Direct-Access     ATA      WDC WD800JD-75MS 1E04 PQ: 0 ANSI: 5
sd 4:0:0:0: [sdb] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 4:0:0:0: Attached scsi generic sg1 type 0
sd 4:0:0:0: [sdb] Attached SCSI disk

And also hot unplug:
ata5: exception Emask 0x10 SAct 0x0 SErr 0x1b0000 action 0xe frozen
ata5: SError: { PHYRdyChg PHYInt 10B8B Dispar }
ata5: hard resetting link
ata5: SATA link down (SStatus 0 SControl 310)
ata5: hard resetting link
ata5: SATA link down (SStatus 0 SControl 310)
ata5: hard resetting link
ata5: SATA link down (SStatus 0 SControl 310)
ata5.00: disabled
ata5: EH complete
ata5.00: detaching (SCSI 4:0:0:0)
sd 4:0:0:0: [sdb] Synchronizing SCSI cache
sd 4:0:0:0: [sdb] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 4:0:0:0: [sdb] Stopping disk
sd 4:0:0:0: [sdb] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
2016-02-25 13:22:16 -05:00
Ondrej Zary 44a9b494f2 sata_via: Apply WD workaround only when needed on VT6421
Currently, workaround for broken WD drives is applied always, slowing
down all drives. And it has a bug - it's not applied after resume.

Apply the workaround only if the error really appears
(SErr == 0x1000500). This allows unaffected drives to run at full speed
(provided that no affected drive is connected to the controller).
Also make sure the workaround is re-applied on resume.

Tested on VT6421.
As SCR registers access is known to cause problems on VT6420 (and I
don't have it to test), keep the workaround applied always on VT6420.

Unaffected drive (Hitachi HDS721680PLA380):
Before:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
 Timing O_DIRECT disk reads: 160 MB in  3.01 seconds =  53.16 MB/sec

After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
 Timing O_DIRECT disk reads: 200 MB in  3.01 seconds =  66.47 MB/sec

Affected drive (WDC WD5003ABYX-18WERA0):
Before:
$ hdparm -t --direct /dev/sda

/dev/sda:
 Timing O_DIRECT disk reads: 180 MB in  3.02 seconds =  59.51 MB/sec

After:
$ hdparm -t --direct /dev/sdb
/dev/sdb:
 Timing O_DIRECT disk reads: 156 MB in  3.03 seconds =  51.48 MB/sec
$ hdparm -t --direct /dev/sdb
/dev/sdb:
 Timing O_DIRECT disk reads: 180 MB in  3.02 seconds =  59.64 MB/sec

The first hdparm is slower because of the error:
[   50.408042] ata5: Incompatible drive: enabling workaround. This slows down transfer rate to ~60 MB/s
[   50.728052] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   50.744834] ata5.00: configured for UDMA/133

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
2016-02-25 13:17:53 -05:00
Quentin Lambert c54c719b55 ata: remove deprecated use of pci api
Replace occurences of the pci api by appropriate call to the dma api.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr)

@deprecated@
idexpression id;
position p;
@@

(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@bad1@
idexpression id;
position deprecated.p;
@@
...when != &id->dev
   when != pci_get_drvdata ( id )
   when != pci_enable_device ( id )
(
  pci_dma_supported@p ( id, ...)
|
  pci_alloc_consistent@p ( id, ...)
)

@depends on !bad1@
idexpression id;
expression direction;
position deprecated.p;
@@

(
- pci_dma_supported@p ( id,
+ dma_supported ( &id->dev,
...
+ , GFP_ATOMIC
  )
|
- pci_alloc_consistent@p ( id,
+ dma_alloc_coherent ( &id->dev,
...
+ , GFP_ATOMIC
  )
)

Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2015-04-08 10:55:05 -04:00
Bartlomiej Zolnierkiewicz 58eb8cd565 ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable.  Benefits of this change:

* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
  and CONFIG_PM_RUNTIME=y configurations

* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
  the future

* more consistent code (there are host drivers which are using the correct
  CONFIG_PM_SLEEP checks already)

The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2014-05-09 22:37:49 -04:00
Paul Gortmaker 1bc1808623 ata: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>.  Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
2014-02-13 16:40:56 -05:00
Tejun Heo 8c3d3d4b12 libata: update "Maintained by:" tags
Jeff moved on to a greener pasture.

 s/Maintained by: Jeff Garzik/Maintained by: Tejun Heo/g

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
2013-05-14 11:13:04 -07:00
Axel Lin 2fc75da0c5 ata: use module_pci_driver
This patch converts the drivers in drivers/ata/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Cc: Mark Lord <kernel@teksavvy.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-07-25 15:12:11 -04:00
Joe Perches 5b933e6340 ata: sata_via: Use dev_dbg
Use normal debugging path for dynamic debug capability.

Convert dev_printk(KERN_DEBUG to dev_dbg(

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-07-23 17:57:36 -04:00
Joe Perches 06296a1e68 ata: Add and use ata_print_version_once
Use a single mechanism to show driver version.
Reduces text a tiny bit too.

Remove uses of static int printed_version
Add and use ata_print_version(const struct device *, const char *ver)
and ata_print_version_once.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 543870	  73893	 116592	 734355	  b34ad	drivers/ata/built-in.allyesconfig.print_once.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 141212	  14689	   4220	 160121	  27179	drivers/ata/built-in.defconfig.print_once.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-07-23 17:57:36 -04:00
Joe Perches a9a79dfec2 ata: Convert ata_<foo>_printk(KERN_<LEVEL> to ata_<foo>_<level>
Saves text by removing nearly duplicated text format strings by
creating ata_<foo>_printk functions and printf extension %pV.

ata defconfig size shrinks ~5% (~8KB), allyesconfig ~2.5% (~13KB)

Format string duplication comes from:

 #define ata_link_printk(link, lv, fmt, args...) do { \
       if (sata_pmp_attached((link)->ap) || (link)->ap->slave_link)    \
               printk("%sata%u.%02u: "fmt, lv, (link)->ap->print_id,   \
                      (link)->pmp , ##args); \
       else \
               printk("%sata%u: "fmt, lv, (link)->ap->print_id , ##args); \
       } while(0)

Coalesce long formats.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.allyesconfig.dev_level.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.defconfig.dev_level.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-07-23 17:57:36 -04:00
Joe Perches a44fec1fce ata: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
Saves a bit of text as the call takes fewer args.

Coalesce a few formats.
Convert a few bare printks to pr_cont.

$ size drivers/ata/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.o.allyesconfig.new
 559574	  73893	 117888	 751355	  b76fb	drivers/ata/built-in.o.allyesconfig.old
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.o.defconfig.new
 149851	  14689	   4220	 168760	  29338	drivers/ata/built-in.o.defconfig.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-07-23 17:57:36 -04:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Sergei Shtylyov 9cbe056f6c libata: remove ATA_FLAG_NO_LEGACY
All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c30670 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efdc6 (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:46 -05:00
Tejun Heo b1353e4f40 sata_via: apply magic FIFO fix to vt6420 too
vt6420 has the same FIFO overflow problem as vt6421 when combined with
certain devices.  This patch applies the magic fix to vt6420 too.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Martin Qvist <q@maq.dk>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-11-19 13:16:26 -05:00
Tejun Heo 97750cebb3 libata: add @ap to ata_wait_register() and introduce ata_msleep()
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration.  These will be used to implement EH exclusion.

This patch doesn't cause any behavior difference.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:05 -04:00
Tejun Heo b475a3b83a sata_via: explain the magic fix
Add Joseph Chan's explanation of the problem and workaround to the
VT6421 magic fix.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-06-07 16:03:08 -04:00
Tejun Heo 8b27ff4cf6 sata_via: magic vt6421 fix for transmission problems w/ WD drives
vt6421 has problems talking to recent WD drives.  It causes a lot of
transmission errors while high bandwidth transfer as reported in the
following bugzilla entry.

  https://bugzilla.kernel.org/show_bug.cgi?id=15173

Joseph Chan provided the following fix.  I don't have any idea what it
does but I can verify the issue is gone with the patch applied.

Signed-off-by: Tejun Heo <tj@kernel.org>
Originally-from: Joseph Chan <JosephChan@via.com.tw>
Reported-by: Jorrit Tijben <sjorrit@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-06-02 13:49:50 -04:00
Tejun Heo 1c5afdf7a6 libata-sff: separate out BMDMA init
Separate out ata_pci_bmdma_prepare_host() and ata_pci_bmdma_init_one()
from their SFF counterparts.  SFF ones no longer try to initialize
BMDMA or set PCI master.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-25 19:40:30 -04:00
Tejun Heo c3b2889424 libata-sff: separate out BMDMA irq handler
Separate out BMDMA irq handler from SFF irq handler.  The misnamed
host_intr() functions are renamed to ata_sff_port_intr() and
ata_bmdma_port_intr().  Common parts are factored into
__ata_sff_port_intr() and __ata_sff_interrupt() and used by sff and
bmdma interrupt routines.

All BMDMA drivers now use ata_bmdma_interrupt() or
ata_bmdma_port_intr() while all non-BMDMA SFF ones use
ata_sff_interrupt() or ata_sff_port_intr().

For now, ata_pci_sff_init_one() uses ata_bmdma_interrupt() as it's
used by both SFF and BMDMA drivers.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-25 19:40:24 -04:00
Tejun Heo 37f65b8bc2 libata-sff: ata_sff_irq_clear() is BMDMA specific
ata_sff_irq_clear() is BMDMA specific.  Rename it to
ata_bmdma_irq_clear(), move it to ata_bmdma_port_ops and make
->sff_irq_clear() optional.

Note: ata_bmdma_irq_clear() is actually only needed by ata_piix and
      possibly by sata_sil.  This should be moved to respective low
      level drivers later.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-25 19:40:19 -04:00
Bart Hartgers a55ab496ea sata_via: Delay on vt6420 when starting ATAPI DMA write
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.

I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.

There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html

Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 15:19:21 -05:00
Bart Hartgers 02d1d6160f sata_via: Correctly setup PIO/DMA for pata slave on vt6421.
Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.

Anyhow, using the same mechanism for both master and slave seems like
a good idea.

Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-03-01 14:58:44 -05:00
JosephChan@via.com.tw f38e35b43f sata_via: Remove redundant device ID for VIA VT8261
Just remove redundant device ID for VIA VT8261.
The device ID 0x9000 and 0x9040 are redundant (for VT8261).
The 0x9040 is reserved for other usage.

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-11-03 14:27:06 -05:00
Jeff Garzik f1c22943e9 [libata] sata_via: kill uninit'd var warning
Reported and initial patch by Marin Mitov.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-04-13 04:09:34 -04:00
Erik Inge Bolsø 14bdef982c [libata] convert drivers to use ata.h mode mask defines
No functional changes in this patch.

Signed-off-by: Erik Inge Bolsø <knan-lkml@anduin.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-03-24 22:13:27 -04:00
JosephChan@via.com.tw 6813952021 sata_via: Add VT8261 support
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:22 -05:00
Marcin Slusarz 554d491de1 sata_via: restore vt*_prepare_host error handling
commit b9d5b89b48 (sata_via: fix support
for 5287) accidently (?) removed vt*_prepare_host error handling - restore it

catched by gcc:
drivers/ata/sata_via.c: In function 'svia_init_one':
drivers/ata/sata_via.c:567: warning: 'host' may be used uninitialized in this function

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:06 -05:00
Tejun Heo b9d5b89b48 sata_via: fix support for 5287
5287 used to be treated as vt6420 but it didn't work.  It's new family
of controllers called vt8251 which hosts four SATA ports as M/S of the
two ATA ports.  This configuration is rather peculiar in that although
the M/S devices are on the same port, each have its own SCR (or
equivalent link status/control) registers which screws up the
port-link-device hierarchy assumed by libata.  Another controller
which falls into this category is ata_piix w/ SIDPR access.

libata now has facility to deal with this class of controllers named
slave_link.  A low level driver for such controllers can just call
ata_slave_link_init() on the respective ports and libata will handle
all the difficult parts like following up with single SRST after
hardresetting both ports.

This patch creates new controller class vt8251, implements slave_link
aware init sequence and config space based SCR access for it and moves
5287 to the new class.

This patch is based on Joseph Chan's larger patch which was created
before slave_link was implemented in libata.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-31 01:43:28 -04:00
Tejun Heo b78152e9db sata_via: load DEVICE register when CTL changes
VIA controllers clear DEVICE register when IEN changes.  Make sure
DEVICE is updated along with CTL.

This change is separated from Joseph Chan's larger patch.

  http://thread.gmane.org/gmane.linux.kernel.commits.mm/40640

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Joseph Chan <JosephChan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:42:47 -04:00
Tejun Heo 82ef04fb4c libata: make SCR access ops per-link
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link.  However, that assumption won't hold anymore with the scheduled
addition of slave link.

Make SCR access ops per-link.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:22:28 -04:00
Tejun Heo 705e76beb9 libata: restructure SFF post-reset readiness waits
Previously, post-softreset readiness is waited as follows.

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
   If not, continue to #3.

3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
   on devmask using ata_sff_wait_ready().

And for post-hardreset readiness,

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. sata_sff_hardreset waits for device readiness using
   ata_sff_wait_ready().

This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().

ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready().  If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.

ata_sff_wait_after_reset() is updated to perform the following steps.

1. waits for 150ms.

2. waits for dev0 readiness using ata_sff_wait_ready().  Note that
   this is done regardless of devmask, as ata_sff_wait_ready() handles
   0xff status correctly, this preserves the original behavior except
   that it may wait longer after softreset if link is online but
   status is 0xff.  This behavior change is very unlikely to cause any
   actual difference and is intended.  It brings softreset behavior to
   that of hardreset.

3. waits for dev1 readiness just the same way ata_bus_post_reset() did.

Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets.  As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.

This change makes reset implementation simpler and more consistent.

While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap.  This is to make them consistent with other
reset helpers and ease core changes.

pata_scc is updated accordingly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo 5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo 9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Tejun Heo 6fd3639011 libata: kill ata_chk_status()
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo 029cfd6b74 libata: implement and use ops inheritance
libata lets low level drivers build ata_port_operations table and
register it with libata core layer.  This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.

This becomes worse for drivers which support related similar
controllers which differ slightly.  They share most of the operations
except for a few.  However, the driver still needs to list all
operations for each variant.  This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.

This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone.  When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time.  Some of those inconsistencies
cause immediate problems and fixed.  Others just remain there dormant
making maintenance increasingly difficult.

To rectify the problem, this patch implements ata_port_operations
inheritance.  To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance.  An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop.  When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified.  This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.

libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma.  To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.

After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to.  The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.

* sata_sx4 is still using old style EH and currently doesn't take
  advantage of ops inheritance.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo 68d1d07b51 libata: implement and use SHT initializers
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer.  This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.

This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht.  Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.

All sht tables are identical before and after this patch.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo 6bd99b4e09 libata: normalize port_info, port_operations and sht tables
Over the time, port info, ops and sht structures developed quite a bit
of inconsistencies.  This patch updates drivers.

* Enable/disable_pm callbacks added to all ahci ops tables.

* Every driver for SFF controllers now uses ata_sff_port_start()
  instead of ata_port_start() unless the driver has custom
  implementation.

* Every driver for SFF controllers now uses ata_pci_default_filter()
  unless the driver has custom implementation.

* Removed an odd port_info->sht initialization from ata_piix.c.
  Likely a merge byproduct.

* A port which has ATA_FLAG_SATA set doesn't need to set cable_detect
  to ata_cable_sata().  Remove it from via and mv port ops.

* Some drivers had unnecessary .max_sectors initialization which is
  ignored and was missing .slave_destroy callback.  Fixed.

* Removed unnecessary sht initializations port_info's.

* Removed onsolete scsi device suspend/resume callbacks from
  pata_bf54x.

* No reason to set ata_pci_default_filter() and bmdma functions for
  PIO-only drivers.  Remove those callbacks and replace
  ata_bmdma_irq_clear with ata_noop_irq_clear.

* pata_platform sets port_start to ata_dummy_ret0.  port_start can
  just be set to NULL.

* sata_fsl supports NCQ but was missing qc_defer.  Fixed.

* pata_rb600_cf implements dummy port_start.  Removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
Harvey Harrison 48e1f800ea ata: fix sparse warning in sata_via.c
drivers/ata/sata_via.c:336:2: warning: returning void-valued expression

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:51:01 -05:00
Alejandro Riveira Fernández 4f743d1d22 sata_via.c: Remove missleading comment.
Maybe for the trivial tree...

sata_via.c has PATA support since:

  d73f30e1c9

  sata_via: PATA support

AFAICS so the TODO list is no longer true.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-06 07:00:33 -05:00
Jeff Garzik 5796d1c4c8 [libata] Address some checkpatch-spotted issues
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 06:15:27 -04:00
Al Viro b4482a4b2e more trivial signedness fixes in drivers
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-14 12:41:52 -07:00
Tejun Heo b6d6c74628 sata_via: kill SATA_PATA_SHARING register handling
The SATA_PATA_SHARING register doesn't have anything to do with the
SATA part of the controller.  It indicates whether an extern SATA PHY
is attached to the PATA part of the controller and if so how it is
wired.  As the PATA part is driven by pata_via, sata_via has no reason
to care about that.  Also, pata_via should work fine under all
configurations.

This patch removes unnecessary attach failures.  It seems recent via
chipsets are defaulting to different values or are actually connected
to SATA PHY triggering this more often.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:42 -04:00
Tejun Heo cbcdd87593 libata: implement and use ata_port_desc() to report port configuration
Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:37 -04:00
Jeff Garzik ac8869d56d [libata] Remove ->port_disable() hook
It was always set to ata_port_disable().  Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:35 -04:00
Jeff Garzik 6d32d30f55 [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:34 -04:00
Tejun Heo cc0680a580 libata-link: linkify reset
Make reset methods and related functions deal with ata_link instead of
ata_port.

* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:31 -04:00
Tejun Heo 9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Ondrej Zary b4154d4a01 Fix sata_via write errors on PATA drive connected to VT6421
I think that I've found and fixed the problem. There is a copy/paste bug in
vt6421_set_dma_mode() function which causes wrong values to be written to
PATA_UDMA_TIMING register.

This patch fixes a copy/paste bug that breaks DMA modes on VT6421 PATA port.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-01 06:52:18 -04:00