apb_calc_first_last(), apb_fake_ranges(), pci_of_scan_bus(),
of_scan_pci_bridge(), pci_of_scan_bus(), and pci_scan_one_pbm()
should all be __devinit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor refactoring in the generic code was necessary for
this:
1) This controller requires 8-byte access to the interrupt map
and clear register. They are 64-bits on all the other
SBUS and PCI controllers anyways, so this was easy to cure.
2) The IMAP register has a different layout and some bits that we
need to preserve, so use a read/modify/write when making
changes to the IMAP register in generic code.
3) Flushing the entire IOMMU TLB is best done with a single write
to a register on this PCI controller, add a iommu->iommu_flushinv
for this.
Still lacks MSI support, that will come later.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fixups for the R7785RP board. Gets iVDR working.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the shared APM emulation code being introduced, hp6xx was missed
in the conversion. Get it building again.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
hp6xx requires some additional IRQs that aren't currently enabled in
the SH7709 setup code. Wire them up.
Signed-off-by: Takashi YOSHII <takashi.yoshii.ze@hitachi.com>
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds more full-featured support for the SH7722 Solution Engine.
Previously this was using the generic board, and lacked most of the
peripheral support.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was done in cpuinfo, but with the number of clocks
growing, it makes more sense to place this in a different proc entry.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7722 (MobileR) to the clock framework.
Signed-off-by: dmitry pervushin <dimka@nomadgs.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Drop the hd64461 I/O ops and wire up pata_platform for MMIO.
Signed-off-by: Kristoffer Ericson <Kristoffer_e1@hotmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the SH7780 PCIC on the Solution Engine 7780,
missing from the previous board-support patch.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7780-based Solution Engine reference board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we've been handling udivdi3 references and wrapping
them in to div64_32() automatically. This doesn't get a lot of
use, however, and as akpm noted in the recent thread on l-k:
http://lkml.org/lkml/2007/2/27/241
we're better off simply ripping it out and going the do_div()
route if there happen to be any places that need it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks some of the node 0 bootmem initialization in
preparation for discontigmem and sparsemem support.
ARCH_POPULATES_NODE_MAP is switched to as a result of this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updates for the landisk board:
- The push_switch framework was used.
- landisk_pwb.c was divided into psw.c and gio.c.
- pata_platform was supported in USL-5P.
- irq.c was rewritten.
- io.c was replaced with generic I/O routines.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements stricter and more compliant knightrider strobing in the
heartbeat handler. While there still seems to be some debate as to
whether the double 0 is "more" correct or not, this updated version
appears to have general consensus. Fixes a long-term "bug".
Signed-off-by: Takashi YOSHII <takashi.yoshii.ze@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables pata_platform support for the PCMCIA slot on the
SolutionEngine.
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Each board sets the total number of IRQs that it's interested in via
the machvec. Previously we cared about the off vs on-chip IRQ range,
but any code relying on that is long dead. Set NR_IRQS to something
sensible given the vector range, and allow boards to cap it if they
really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wire up GENERIC_BUG for SH. This moves off of the special bug
frame and on to the generic struct bug_entry. Roughly the same
semantics are retained, and we can kill off some of the verbose
BUG() reporting code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7780 has a speculative execution mode where it can speculatively
perform an instruction fetch for subroutine returns, this allows it
to be enabled. There are some various pitfalls associated with this
mode, so it's left as depending on CONFIG_EXPERIMENTAL and not
enabled by default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb thread support is woefully out of date (it predates
the pidhash), and needs a complete rewrite before it's useful
again. Just rip it out entirely.
Updating the unified kgdb stub is a more worthwhile endeavour
for anyone that happens to be interested in this, at present
it's just limping along.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has suffered quite a bit of bitrot, do some basic
tidying to get it to a reasonably functional state again.
This gets the basic support and the console working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
utrace removes the ptrace_message field in task_struct. Move our use
of this field into a new member in thread_info called "syscall"
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/voyager-2.6:
[VOYAGER] add smp alternatives
[VOYAGER] Use modern techniques to setup and teardown low identiy mappings.
[VOYAGER] Convert the monitor thread to use the kthread API
[VOYAGER] clockevents driver: bring voyager in to line
[VOYAGER] clockevents: correct boot cpu is zero assumption
[VOYAGER] add smp_call_function_single
linux/mmc/protocol.h header is gone, thus breaking the build of the
mach-qt2410.c file. As this header is not used, I'm removing it. The
right headers may still be added later if needed.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__ioremap() took a set of page table flags (specifically the cacheable
and bufferable bits) to control the mapping type. However, with
the advent of ARMv6, this is far too limited.
Replace the page table flags with a memory type index, so that the
desired attributes can be selected from the mem_type table.
Finally, to prevent silent miscompilation due to the differing
arguments, rename the __ioremap() and __ioremap_pfn() functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add cached device type for ioremap_cached(). Group all device memory
types together, and ensure that they all have a "MT_DEVICE" prefix.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the memory types table to define the L1 descriptor bit 4 to
be in terms of the ARMv6 definition - execute never.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix oops in omap16xx mpuio suspend/resume code; field wasn't initialized
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
GPIO and MPUIO wake updates:
- Hook MPUIOs into the irq wakeup framework too. This uses a platform
device to update irq enables during system sleep states, instead of
a sys_device, since the latter is no longer needed for such things.
- Also forward enable/disable irq wake requests to the relevant GPIO
controller, so the top level IRQ dispatcher can (eventually) handle
these wakeup events automatically if more than one GPIO pin needs to
be a wakeup event source.
- Minor tweak to the 24xx non-wakeup gpio stuff: no need to check such
read-only data under the spinlock.
This assumes (maybe wrongly?) that only 16xx can do GPIO wakeup; without
a 15xx I can't test such stuff.
Also this expects the top level IRQ dispatcher to properly handle requests
to enable/disable irq wake, which is currently known to be wrong: omap1
saves the flags but ignores them, omap2 doesn't even save it. (Wakeup
events are, wrongly, hardwired in the relevant mach-omapX/pm.c file ...)
So MPUIO irqs won't yet trigger system wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Speedup and shrink GPIO irq handling code, by using a pointer
that's available in the irq_chip structure instead of calling
the get_gpio_bank() function. On OMAP1 this saves 44 words,
most of which were in IRQ critical path methods. Hey, every
few instructions help.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
More GPIO/IRQ cleanup:
- compile-time removal of much useless code
* mpuio support on non-OMAP1.
* 15xx/730/24xx gpio support on 1610
* 15xx/730/16xx gpio support on 24xx
* etc
- remove all BUG() calls, which are always bad news ... replaced some
with normal fault reports for that call, others with WARN_ON(1).
- small mpuio bugfix: add missing set_type() method
Oh, and fix a minor merge issue: inode->u.generic_ip is now gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add some GPIO debug support: /sys/kernel/debug/omap_gpio dumps the state
of all GPIOs that have been claimed, including basic IRQ info if relevant.
Tested on 24xx, 16xx.
Includes minor bugfixes: recording IRQ trigger mode (this should probably
be a genirq patch), adding missing space to non-wakeup warning
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some GPIOs on OMAP2420 do not have wakeup capabilities. If these GPIOs
are configured as IRQ sources, spurious interrupts will be generated
each time the core domain enters retention.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable 24xx GPIO autoidling
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the D-Link DSM-G600 Rev A.
This is an ARM XScale IXP4xx system relatively similar to
the NSLU2 and NAS-100D already supported by mainline. An
important difference is Gigabit Ethernet support using
the Via Velocity chipset.
This patch is the combined work of Michael Westerhof and
Alessandro Zummo, with contributions from Michael-Luke
Jones. This version addresses review comments from rmk
and Deepak Saxena.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (49 commits)
[SCTP]: Set assoc_id correctly during INIT collision.
[SCTP]: Re-order SCTP initializations to avoid race with sctp_rcv()
[SCTP]: Fix the SO_REUSEADDR handling to be similar to TCP.
[SCTP]: Verify all destination ports in sctp_connectx.
[XFRM] SPD info TLV aggregation
[XFRM] SAD info TLV aggregationx
[AF_RXRPC]: Sort out MTU handling.
[AF_IUCV/IUCV] : Add missing section annotations
[AF_IUCV]: Implementation of a skb backlog queue
[NETLINK]: Remove bogus BUG_ON
[IPV6]: Some cleanups in include/net/ipv6.h
[TCP]: zero out rx_opt in tcp_disconnect()
[BNX2]: Fix TSO problem with small MSS.
[NET]: Rework dev_base via list_head (v3)
[TCP] Highspeed: Limited slow-start is nowadays in tcp_slow_start
[BNX2]: Update version and reldate.
[BNX2]: Print bus information for PCIE devices.
[BNX2]: Add 1-shot MSI handler for 5709.
[BNX2]: Restructure PHY event handling.
[BNX2]: Add indirect spinlock.
...
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (65 commits)
Input: gpio_keys - add support for switches (EV_SW)
Input: cobalt_btns - convert to use polldev library
Input: add skeleton for simple polled devices
Input: update some documentation
Input: wistron - fix typo in keymap for Acer TM610
Input: add input_set_capability() helper
Input: i8042 - add Fujitsu touchscreen/touchpad PNP IDs
Input: i8042 - add Panasonic CF-29 to nomux list
Input: lifebook - split into 2 devices
Input: lifebook - add signature of Panasonic CF-29
Input: lifebook - activate 6-byte protocol on select models
Input: lifebook - work properly on Panasonic CF-18
Input: cobalt buttons - separate device and driver registration
Input: ati_remote - make button repeat sensitivity configurable
Input: pxa27x - do not use deprecated SA_INTERRUPT flag
Input: ucb1400 - make delays configurable
Input: misc devices - switch to using input_dev->dev.parent
Input: joysticks - switch to using input_dev->dev.parent
Input: touchscreens - switch to using input_dev->dev.parent
Input: mice - switch to using input_dev->dev.parent
...
Fixed up conflicts with core device model removal of "struct subsystem" manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6:
remove "struct subsystem" as it is no longer needed
sysfs: printk format warning
DOC: Fix wrong identifier name in Documentation/driver-model/devres.txt
platform: reorder platform_device_del
Driver core: fix show_uevent from taking up way too much stack
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
Fix a crash caused by requests placed in the queue with the completed flag
already set. This lead to some ADB_SYNC requests returning early and their
request structs being popped off the stack while still queued. Stack corruption
ensued or an invalid request callback pointer was invoked or both. Eliminate
macii_retransmit() and its buggy implementation of macii_write(). Have
macii_queue_poll() fully initialise the request queues.
Fix a bug in macii_queue_poll() where the last_req pointer was not being set.
This caused some requests to leave the queue before being completed (and would
also corrupt the stack under certain conditions).
Fix a race in macii_start that could set the state machine to "reading" while
current_req was null.
No longer send poll commands with the ADBREQ_REPLY flag -- doing that caused
the replies to be stored in the request buffer where they were forgotten
about.
Don't autopoll by continuously sending new Talk commands. Get the controller to
do that for us. This reduces the ADB interrupt rate on an idle bus to about 5
per second. Only autopoll the devices that were probed.
Explicitly clear the interrupt flag when polling.
Use disable_irq rather than local_irq_save when polling.
Remove excess local_irq_save/restore pairs.
Improve bus timeout and service request detection.
Remove unused code (last_reply, adb_dir etc) and unneeded code (prefix_len,
first_byte etc).
Change TIP and TACK to their correct names on this ADB controller (ST_EVEN and
ST_ODD).
Add some commentry.
Add a generous quantity of sanity checks (BUG_ONs).
Let m68k macs use the adb_sync boot param too.
Tested on Mac II, Mac IIci, Quadra 650, Quadra 700 etc.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no slow IRQs on Macs since Roman Zippel's IRQ reorganisation that
went into 2.6.16 and removed mac_irq_list[] and the do_mac_irq_list()
dispatcher. (They were implemented in do_mac_irq_list() by lowering the IPL.)
Hence there's no more use for mutual exclusion in the Mac interrupt
dispatchers. Remove it.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some Macs lack a slot interrupt enable register. So the existing code makes
disabled and unregistered slot IRQ lines outputs set high. This seems to work
on quadras, but does not work on genuine VIAs (perhaps the card still succeeds
in pulling the line low, or perhaps because this increases the settle time on
the port A input, meaning that the CA1 IRQ could fire before the slot line
reads active).
Because of this, the nubus_active flags were used to mask IRQs, which is
actually worse than the problem it tries to solve. Any interrupt masked by
nubus_active will remain asserted and prevent further transitions on CA1. And
so the nubus gets wedged regardless of hardware (emulated VIA ASIC, real VIA
chip or RBV).
The best solution to this hardware limitation of genuine VIAs is to disable the
umbrella SLOTS IRQ when disabling a slot on those machines. Unfortunately, this
means all slot IRQs get disabled when any slot IRQ is disabled. But it is only
a problem when there's more than 1 device using nubus interrupts.
Another potential problem for genuine VIAs is an unregistered nubus IRQ.
Eventually it will be possible to enable the CA1 interrupt by installing its
handler only _after_ all nubus drivers have loaded but _before_ the kernel
needs them, at which time this last problem can be fixed. For now it can be
worked around:
- disable MacOS extensions
- don't boot MacOS (use the Emile bootloader instead)
- get the bootloaders to disable ROM drivers (Penguin does this for video
cards already, don't know about Emile)
- physically remove unsupported cards
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure that there are no slot IRQs asserted before leaving the nubus
handler. If there are and we don't then the nubus gets wedged because this
prevents a CA1 transition, which means no more nubus IRQs.
Make the interrupt dispatch loops terminate sooner.
Explicitly initialise the VIA latches to make the code more easily understood.
Also some cleanups.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reverse the last of a monumental brown-paper-bag commit that went into the 2.3
kernel.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some more machines that support A/UX interrupt priorities. There are
probably others as well, but I've only tested these ones so far.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only attempt to initialize the amount of interrupts a sun3 actually has...
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add early parameter support and convert current users to it.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat various m68k files, so they actually look like Linux sources.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Atari keyboard and mouse support.
(reformating and Kconfig fixes by Roman Zippel)
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c1821c2e97 introduced the
uaccess structure that is used to select the correct set of user
copy functions for the different execution modes (standard vs.
noexec vs. z9 optimized user copy). The uaccess symbol is exported
with EXPORT_SYMBOL_GPL. This breaks all non-gpl modules that use
user copy. To make them work again change the export to
EXPORT_SYMBOL.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register aes-s390 algorithms with the actual supported max keylen size
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
And here's a port of the powerpc patch to get rid of the notifier
chain completely to s390. It's ontop of Martins patch as that one
is in mainline already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cleanup of dev_base list use, with the aim to simplify making device
list per-namespace. In almost every occasion, use of dev_base variable
and dev->next pointer could be easily replaced by for_each_netdev
loop. A few most complicated places were converted to using
first_netdev()/next_netdev().
Signed-off-by: Pavel Emelianov <xemul@openvz.org>
Acked-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's surround constructs like:
orr r3, r3, #(KERNEL_RAM_PADDR & 0x00f00000)
between .if .endif since (KERNEL_RAM_PADDR & 0x00f00000) is 0 in 99% of
all cases.
Also let's mask PHYS_OFFSET with 0x00f00000 instead of 0x00e00000.
Section mappings are really 1MB not 2MB and the 2MB groupping is
a higher level issue already much better enforced with
#if (PHYS_OFFSET & 0x001fffff)
#error "PHYS_OFFSET must be at an even 2MiB boundary!"
#endif
at the top of the file.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK
boards.
SAM9260-EK:
- Register I2C device.
SAM9263-EK:
- Add platform_data and register MACB device.
(Patch by Nicolas Ferre)
- Add platform_data and register AC97 device.
(Patch by Nicolas Ferre)
- Register I2C device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
'type' in the struct expansion_card is only used to indicate
whether this card is an EASI card or not. Therefore, having
it as an enum is wasteful (and introduces additional noise
when we come to remove the enum.) Convert it to a mere flag
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the startup of kecardd to use kthread_run not a
kernel_thread combination of kernel_thread and daemonize. Making the code
slightly simpler and more maintainable.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add pata_platform device for RiscPC, thereby converting the primary
IDE channel on the machine to PATA.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Although expansion cards can't do bus-master DMA, subsystems
want to be able to use coherent memory for DMA purposes to
these cards. Therefore, set the coherent DMA mask to allow
such memory to be allocated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9263-EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9261-EK board.
Original patch by Morten Larsen.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define and register the remaining peripheral clocks for the AT91
processors.
AT91SAM9261 clocks patch by Ivan Zhakov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that do_undefinstr handles kernel and user mode undefined
instruction exceptions it must not assume that interrupts are enabled at
entry.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The tpmi units interface with the SAS controller on iop348.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the iop3xx platform support code assumes that RedBoot is the
bootloader and has already initialized the ATU. Linux should handle this
initialization for three reasons:
1/ The memory map that RedBoot sets up is not optimal (page_to_dma and
virt_to_phys return different addresses). The effect of this is that using
the dma mapping API for the internal bus dma units generates pci bus
addresses that are incorrect for the internal bus.
2/ Not all iop platforms use RedBoot
3/ If the ATU is already initialized it indicates that the iop is an add-in
card in another host, it does not own the PCI bus, and should not be
re-initialized.
Changelog:
* rather than change nr_controllers to zero, simply do not call
pci_common_init
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add more information to PCI resource collision message
to help with debugging.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
set_irq_msi() currently connects an irq_desc to an msi_desc. The archs call
it at some point in their setup routine, and then the generic code sets up the
reverse mapping from the msi_desc back to the irq.
set_irq_msi() should do both connections, making it the one and only call
required to connect an irq with it's MSI desc and vice versa.
The arch code MUST call set_irq_msi(), and it must do so only once it's sure
it's not going to fail the irq allocation.
Given that there's no need for the arch to return the irq anymore, the return
value from the arch setup routine just becomes 0 for success and anything else
for failure.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allows architectures to advertise that they support MSI rather than listing
each architecture as a PCI_MSI dependency.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert code that allocs a struct pci_dev to use alloc_pci_dev().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At one time, if a BIOS ROM shadow was detected for the boot video
device (stored at offset 0xc0000), we'd set a special resource flag,
IORESOURCE_ROM_SHADOW, so that the sysfs ROM file code could handle
it properly. That broke along the way somewhere though, so current
kernels will be missing 'rom' files in sysfs if the video device
doesn't have an explicit ROM BAR.
This patch fixes the regression by moving the video fixup quirk to a
little later in the boot cycle (to avoid having its work undone by
PCI resource allocation) and checking in the PCI sysfs code whether
a rom file should be created due to a shadow resource, which is also
moved to a little later in the boot cycle so it will occur after the
video fixup. Tested and works on my i386 test box.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to work on cleaning up the relationship between kobjects, ksets and
ktypes. The removal of 'struct subsystem' is the first step of this,
especially as it is not really needed at all.
Thanks to Kay for fixing the bugs in this patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In arch/i386/cpu/common.c there is:
cpu_devs[X86_VENDOR_INTEL]
cpu_devs[X86_VENDOR_CYRIX]
cpu_devs[X86_VENDOR_AMD]
...
They are all filled with data early.
The data (struct) got set to NULL for all, but Intel in different
late_initcall (exit_cpu_vendor) calls.
I don't see what sense this makes at all, maybe something that got
forgotten with the HOTPLUG_CPU extenstions?
Please check/review whether initdata, cpuinitdata is still ok and this
still works with HOTPLUG_CPU and without, it should...
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: davej@redhat.com
In the case of !CONFIG_PCI_DIRECT && !CONFIG_PCI_MMCONFIG, type is
unreferened.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
On i945, a mmconfig range hitting the f0000000-ffffffff zone conflicts
with the APIC registers and others. Consider it invalid.
On E7520, values 0000 and f000 for the window register are defined
invalid in the documentation.
I haven't seen a bios use these values, but who trusts biosen these
days?
Signed-off-by: Olivier Galibert <galibert@pobox.com>
Signed-off-by: Andi Kleen <ak@suse.de>
arch/i386/pci/mmconfig-shared.c | 25 +++++++++++++++++--------
1 file changed, 17 insertions(+), 8 deletions(-)
Only 1GB-aligned kernel/user splits are now handled for PAE. The
2GB/2GB split attempts to avoid aliasing vmallocspace with the 1:1
mapping for physical memory by using an actual split of 1.875/2.125
to accommodate 128MB of vmallocspace out of what would otherwise
be a full 2GB for userspace. That attempt disturbs the alignment
required by PAE for 2GB/2GB splits, and furthermore does not provide
a 2GB/2GB split as advertised.
This patch resolves the issues here in two manners. The first is
by providing a true 2GB/2GB split in addition to the 1.875/2.125
split. The second is by renaming the 1.875/2.125 split to
CONFIG_VMSPLIT_2G_OPT analogously to CONFIG_VMSPLIT_3G_OPT, which
performs a similar manuever to avoid aliasing vmallocspace with
the 1:1 mapping for physical memory around the 3GB boundary. With
the 1.875/2.125 split properly-named, its config option is then
tagged as depending on !HIGHMEM to express the PAE implementation's
current inability to deal with such unaligned splits.
This patch is essentially a combination of two patches, one written
by Eric Biederman and the other by Eric Dumazet. If they could add
their Signed-off-by: to this, I'd be much obliged.
Signed-off-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Mark Lord <lkml@rtr.ca>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Fix:
In file included from include2/asm/apic.h:5,
from include2/asm/smp.h:15,
from linux/arch/x86_64/kernel/genapic_flat.c:18:
linux/include/linux/pm.h: In function ‘call_platform_enable_wakeup’:
linux/include/linux/pm.h:331: error: ‘EIO’ undeclared (first use in this function)
linux/include/linux/pm.h:331: error: (Each undeclared identifier is reported only once
linux/include/linux/pm.h:331: error: for each function it appears in.)
Signed-off-by: Andi Kleen <ak@suse.de>
The option never worked well and functionlist wasn't well maintained.
Also it made the build very slow on many binutils version.
So just remove it.
Cc: arjan@linux.intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
This was supposed to see the full memory on a ASUS A8SX motherboard
with 4GB RAM where the northbridge reports less memory, but it didn't
help there. But it's a reasonable change so let's include it anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Check some CPUID bits that are needed for compiler generated early in boot.
When the system is still in real mode before changing the VESA BIOS mode
it is possible to still display an visible error message on the screen.
Similar to x86-64.
Includes cleanups from Eric Biederman
Signed-off-by: Andi Kleen <ak@suse.de>
- Use 64bit TSC calculations to avoid handling overflow
- Use 32bit unsigned arithmetic for the APIC timer. This
way overflows are handled correctly.
- Fix exit check of loop to account for apic timer counting down
Signed-off-by: dpreed@reed.com
Signed-off-by: Andi Kleen <ak@suse.de>
- Introduce a wd_ops structure
- Convert the various nmi watchdogs over to it
- This allows to split the perfctr reservation from the watchdog
setup cleanly.
- Do perfctr reservation globally as it should have always been
- Remove dead code referenced only by unused EXPORT_SYMBOLs
Signed-off-by: Andi Kleen <ak@suse.de>
Set the node_possible_map at runtime on x86_64. On a non NUMA system,
num_possible_nodes() will now say '1'.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Background:
We've found that MCEs (specifically DRAM SBEs) tend to come in bunches,
especially when we are trying really hard to stress the system out. The
current MCE poller uses a static interval which does not care whether it
has or has not found MCEs recently.
Description:
This patch makes the MCE poller adjust the polling interval dynamically.
If we find an MCE, poll 2x faster (down to 10 ms). When we stop finding
MCEs, poll 2x slower (up to check_interval seconds). The check_interval
tunable becomes the max polling interval. The "Machine check events
logged" printk() is rate limited to the check_interval, which should be
identical behavior to the old functionality.
Result:
If you start to take a lot of correctable errors (not exceptions), you
log them faster and more accurately (less chance of overflowing the MCA
registers). If you don't take a lot of errors, you will see no change.
Alternatives:
I considered simply reducing the polling interval to 10 ms immediately
and keeping it there as long as we continue to find errors. This felt a
bit heavy handed, but does perform significantly better for the default
check_interval of 5 minutes (we're using a few seconds when testing for
DRAM errors). I could be convinced to go with this, if anyone felt it
was not too aggressive.
Testing:
I used an error-injecting DIMM to create lots of correctable DRAM errors
and verified that the polling interval accelerates. The printk() only
happens once per check_interval seconds.
Patch:
This patch is against 2.6.21-rc7.
Signed-Off-By: Tim Hockin <thockin@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data:cpu_llc_id from __ksymtab between '__ksymtab_cpu_llc_id' (at offset 0x4a0) and '__ksymtab_smp_num_siblings'
It is strange to export a __cpuinitdata symbols to modules, and no module
appears to use it anyway.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch just trivial converts from calling kernel_thread and daemonize
to just calling kthread_run.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The locking of the xtime_lock around the cpu notifier is unessesary now.
At one time the tsc was used after a frequency change for timekeeping, but
the re-write of timekeeping no longer uses the TSC unless the frequency is
constant.
The variables that are changed in this section of code had also once been
used for timekeeping, but not any longer ..
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Currently the i386 architecture checks the family for mce capability and this
removes that and uses the CPUID information. Tested on a K8 revE and a
family10h processor.
This eliminates checking of a set AMD procesor family if mce is
allowed and relies on the information being in CPUID.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
IRQ is already disabled through local_irq_disable(). So
spin_lock_irqsave() can be replaced with spin_lock().
Signed-off-by: Hisashi Hifumi <hifumi.hisashi@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Avoid checking for cpu gone in mm hot path when CONFIG_HOTPLUG_CPU is not
defined.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We apparently hit the 1024 limit of vsyscall_0 zone when some debugging
options are set, or if __vsyscall_gtod_data is 64 bytes larger.
In order to save 128 bytes from the vsyscall_0 zone, we move __vgetcpu_mode
& __jiffies to vsyscall_2 zone where they really belong, since they are
used only from vgetcpu() (which is in this vsyscall_2 area).
After patch is applied, new layout is :
ffffffffff600000 T vgettimeofday
ffffffffff60004e t vsysc2
ffffffffff600140 t vread_hpet
ffffffffff600150 t vread_tsc
ffffffffff600180 D __vsyscall_gtod_data
ffffffffff600400 T vtime
ffffffffff600413 t vsysc1
ffffffffff600800 T vgetcpu
ffffffffff600870 D __vgetcpu_mode
ffffffffff600880 D __jiffies
ffffffffff600c00 T venosys_1
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
startup_ipi_hook depends on CONFIG_X86_LOCAL_APIC, so move it to the
right part of the paravirt_ops initialization.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix section mismatch warnings in mtrr code.
Fix line length on one source line.
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.data: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x103)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x180)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x199)
WARNING: arch/x86_64/kernel/built-in.o - Section mismatch: reference to .init.text: from .text.get_mtrr_state after 'get_mtrr_state' (at offset 0x1c1)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2007-05-02 19:27:18 +02:00
Fernando Luis [** ISO-8859-1 charset **] VzquezCao
Use safe_apic_wait_icr_idle to check ICR idle bit if the vector is
NMI_VECTOR to avoid potential hangups in the event of crash when kdump
tries to stop the other CPUs.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
2007-05-02 19:27:18 +02:00
Fernando Luis [** ISO-8859-1 charset **] VzquezCao
Implement __send_IPI_dest_field which can be used to send IPIs when the
"destination shorthand" field of the ICR is set to 00 (destination
field). Use it whenever possible.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
2007-05-02 19:27:18 +02:00
Fernando Luis [** ISO-8859-1 charset **] VzquezCao
Implement __send_IPI_dest_field which can be used to send IPIs when the
"destination shorthand" field of the ICR is set to 00 (destination
field). Use it whenever possible.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
inquire_remote_apic is used for APIC debugging, so use
safe_apic_wait_icr_idle instead of apic_wait_icr_idle to avoid possible
lockups when APIC delivery fails.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
__inquire_remote_apic is used for APIC debugging, so use
safe_apic_wait_icr_idle instead of apic_wait_icr_idle to avoid possible
lockups when APIC delivery fails.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
The functionality provided by the new safe_apic_wait_icr_idle is being
open-coded all over "kernel/smpboot.c". Use safe_apic_wait_icr_idle
instead to consolidate code and ease maintenance.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
The functionality provided by the new safe_apic_wait_icr_idle is being
open-coded all over "kernel/smpboot.c". Use safe_apic_wait_icr_idle
instead to consolidate code and ease maintenance.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
apic_wait_icr_idle looks like this:
static __inline__ void apic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
cpu_relax();
}
The busy loop in this function would not be problematic if the
corresponding status bit in the ICR were always updated, but that does
not seem to be the case under certain crash scenarios. Kdump uses an IPI
to stop the other CPUs in the event of a crash, but when any of the
other CPUs are locked-up inside the NMI handler the CPU that sends the
IPI will end up looping forever in the ICR check, effectively
hard-locking the whole system.
Quoting from Intel's "MultiProcessor Specification" (Version 1.4), B-3:
"A local APIC unit indicates successful dispatch of an IPI by
resetting the Delivery Status bit in the Interrupt Command
Register (ICR). The operating system polls the delivery status
bit after sending an INIT or STARTUP IPI until the command has
been dispatched.
A period of 20 microseconds should be sufficient for IPI dispatch
to complete under normal operating conditions. If the IPI is not
successfully dispatched, the operating system can abort the
command. Alternatively, the operating system can retry the IPI by
writing the lower 32-bit double word of the ICR. This “time-out”
mechanism can be implemented through an external interrupt, if
interrupts are enabled on the processor, or through execution of
an instruction or time-stamp counter spin loop."
Intel's documentation suggests the implementation of a time-out
mechanism, which, by the way, is already being open-coded in some parts
of the kernel that tinker with ICR.
Create a apic_wait_icr_idle replacement that implements the time-out
mechanism and that can be used to solve the aforementioned problem.
AK: moved both functions out of line
AK: Added improved loop from Keith Owens
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
apic_wait_icr_idle looks like this:
static __inline__ void apic_wait_icr_idle(void)
{
while (apic_read(APIC_ICR) & APIC_ICR_BUSY)
cpu_relax();
}
The busy loop in this function would not be problematic if the
corresponding status bit in the ICR were always updated, but that does
not seem to be the case under certain crash scenarios. Kdump uses an IPI
to stop the other CPUs in the event of a crash, but when any of the
other CPUs are locked-up inside the NMI handler the CPU that sends the
IPI will end up looping forever in the ICR check, effectively
hard-locking the whole system.
Quoting from Intel's "MultiProcessor Specification" (Version 1.4), B-3:
"A local APIC unit indicates successful dispatch of an IPI by
resetting the Delivery Status bit in the Interrupt Command
Register (ICR). The operating system polls the delivery status
bit after sending an INIT or STARTUP IPI until the command has
been dispatched.
A period of 20 microseconds should be sufficient for IPI dispatch
to complete under normal operating conditions. If the IPI is not
successfully dispatched, the operating system can abort the
command. Alternatively, the operating system can retry the IPI by
writing the lower 32-bit double word of the ICR. This “time-out”
mechanism can be implemented through an external interrupt, if
interrupts are enabled on the processor, or through execution of
an instruction or time-stamp counter spin loop."
Intel's documentation suggests the implementation of a time-out
mechanism, which, by the way, is already being open-coded in some parts
of the kernel that tinker with ICR.
Create a apic_wait_icr_idle replacement that implements the time-out
mechanism and that can be used to solve the aforementioned problem.
AK: moved both functions out of line
AK: added improved loop from Keith Owens
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
If our copy of the MTRRs of the BSP has RdMem or WrMem set, and
we are running on an AMD64/K8 system, the boot CPU must have had
MtrrFixDramEn and MtrrFixDramModEn set (otherwise our RDMSR would
have copied these bits cleared), so we set them on this CPU as well.
This allows us to keep the AMD64/K8 RdMem and WrMem bits in sync
across the CPUs of SMP systems in order to fullfill the duty of
system software to "initialize and maintain MTRR consistency
across all processors." as written in the AMD and Intel manuals.
If an WRMSR instruction fails because MtrrFixDramModEn is not
set, I expect that also the Intel-style MTRR bits are not updated.
AK: minor cleanup, moved MSR defines around
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Note: This patch didn'nt need an update since it's initial post.
Some BIOSes may modify fixed-range MTRRs in SMM, e.g. when they
transition the system into ACPI mode, which is entered thru an SMI,
triggered by Linux in acpi_enable().
SMIs which cause that Linux is interrupted and BIOS code is
executed (which may change e.g. fixed-range MTRRs) in SMM may
be raised by an embedded system controller which is often found
in notebooks also at other occasions.
If we would not update our copy of the fixed-range MTRRs before
suspending to RAM or to disk, restore_processor_state() would
set the fixed-range MTRRs of the BSP using old backup values
which may be outdated and this could cause the system to fail
later during resume.
This patch ensures that our copy of the fixed-range MTRRs
is updated when saving the boot processor state on suspend
to disk and suspend to RAM.
In combination with other patches this allows to fix s2ram
and s2disk on the Acer Ferrari 1000 notebook and at least
s2disk on the Acer Ferrari 5000 notebook.
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Applied fix by Andew Morton:
http://lkml.org/lkml/2007/4/8/88 - Fix `make headers_check'.
AMD and Intel x86 CPU manuals state that it is the responsibility of
system software to initialize and maintain MTRR consistency across
all processors in Multi-Processing Environments.
Quote from page 188 of the AMD64 System Programming manual (Volume 2):
7.6.5 MTRRs in Multi-Processing Environments
"In multi-processing environments, the MTRRs located in all processors must
characterize memory in the same way. Generally, this means that identical
values are written to the MTRRs used by the processors." (short omission here)
"Failure to do so may result in coherency violations or loss of atomicity.
Processor implementations do not check the MTRR settings in other processors
to ensure consistency. It is the responsibility of system software to
initialize and maintain MTRR consistency across all processors."
Current Linux MTRR code already implements the above in the case that the
BIOS does not properly initialize MTRRs on the secondary processors,
but the case where the fixed-range MTRRs of the boot processor are changed
after Linux started to boot, before the initialsation of a secondary
processor, is not handled yet.
In this case, secondary processors are currently initialized by Linux
with MTRRs which the boot processor had very early, when mtrr_bp_init()
did run, but not with the MTRRs which the boot processor uses at the
time when that secondary processors is actually booted,
causing differing MTRR contents on the secondary processors.
Such situation happens on Acer Ferrari 1000 and 5000 notebooks where the
BIOS enables and sets AMD-specific IORR bits in the fixed-range MTRRs
of the boot processor when it transitions the system into ACPI mode.
The SMI handler of the BIOS does this in SMM, entered while Linux ACPI
code runs acpi_enable().
Other occasions where the SMI handler of the BIOS may change bits in
the MTRRs could occur as well. To initialize newly booted secodary
processors with the fixed-range MTRRs which the boot processor uses
at that time, this patch saves the fixed-range MTRRs of the boot
processor before new secondary processors are started. When the
secondary processors run their Linux initialisation code, their
fixed-range MTRRs will be updated with the saved fixed-range MTRRs.
If CONFIG_MTRR is not set, we define mtrr_save_state
as an empty statement because there is nothing to do.
Possible TODOs:
*) CPU-hotplugging outside of SMP suspend/resume is not yet tested
with this patch.
*) If, even in this case, an AP never runs i386/do_boot_cpu or x86_64/cpu_up,
then the calls to mtrr_save_state() could be replaced by calls to
mtrr_save_fixed_ranges(NULL) and mtrr_save_state() would not be
needed.
That would need either verification of the CPU-hotplug code or
at least a test on a >2 CPU machine.
*) The MTRRs of other running processors are not yet checked at this
time but it might be interesting to syncronize the MTTRs of all
processors before booting. That would be an incremental patch,
but of rather low priority since there is no machine known so
far which would require this.
AK: moved prototypes on x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
In this current implementation which is used in other patches,
mtrr_save_fixed_ranges() accepts a dummy void pointer because
in the current implementation of one of these patches, this
function may be called from smp_call_function_single() which
requires that this function takes a void pointer argument.
This function calls get_fixed_ranges(), passing mtrr_state.fixed_ranges
which is the element of the static struct which stores our current
backup of the fixed-range MTRR values which all CPUs shall be
using.
Because mtrr_save_fixed_ranges calls get_fixed_ranges after
kernel initialisation time, __init needs to be removed from
the declaration of get_fixed_ranges().
If CONFIG_MTRR is not set, we define mtrr_save_fixed_ranges
as an empty statement because there is nothing to do.
AK: Moved prototypes for x86-64 around to fix warnings
Signed-off-by: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Three cleanups:
1: ELF notes are never mapped, so there's no need to have any access
flags in their phdr.
2: When generating them from asm, tell the assembler to use a SHT_NOTE
section type. There doesn't seem to be a way to do this from C.
3: Use ANSI rather than traditional cpp behaviour to stringify the
macro argument.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Otherwise non GPL modules cannot even do basic operations
like disabling interrupts anymore, which would be excessive.
Longer term should split the single structure up into
internal and external symbols and not export the internal
ones at all.
Signed-off-by: Andi Kleen <ak@suse.de>
The other symbols used to delineate the alt-instructions sections have the
form __foo/__foo_end. Rename parainstructions to match.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Convert VMI timer to use clock events, making it properly able to use the NO_HZ
infrastructure. On UP systems, with no local APIC, we just continue to route
these events through the PIT. On systems with a local APIC, or SMP, we provide
a single source interrupt chip which creates the local timer IRQ. It actually
gets delivered by the APIC hardware, but we don't want to use the same local
APIC clocksource processing, so we create our own handler here.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Dan Hecht <dhecht@vmware.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
David S. Miller