Commit Graph

356 Commits

Author SHA1 Message Date
Xiaotian Feng 26cd4d65de [libata] fix Null pointer dereference on disk error
Following oops were observed when disk error happened:

[ 4272.896937] sd 0:0:0:0: [sda] Unhandled error code
[ 4272.896939] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 4272.896942] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 00 5a de a7 00 00 08 00
[ 4272.896951] end_request: I/O error, dev sda, sector 5955239
[ 4291.574947] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4291.658305] IP: [] ahci_activity_show+0x1/0x40
[ 4291.730090] PGD 76dbbc067 PUD 6c4fba067 PMD 0
[ 4291.783408] Oops: 0000 [#1] SMP
[ 4291.822100] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/sw_activity
[ 4291.934235] CPU 9
[ 4291.958301] Pid: 27942, comm: hwinfo ......

ata_scsi_find_dev could return NULL, so ata_scsi_activity_{show,store} should check if atadev is NULL.

Signed-off-by: Xiaotian Feng <dannyfeng@tencent.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-12-14 09:40:34 -05:00
Martin K. Petersen 5db44863b6 [SCSI] sd: Implement support for WRITE SAME
Implement support for WRITE SAME(10) and WRITE SAME(16) in the SCSI disk
driver.

 - We set the default maximum to 0xFFFF because there are several
   devices out there that only support two-byte block counts even with
   WRITE SAME(16). We only enable transfers bigger than 0xFFFF if the
   device explicitly reports MAXIMUM WRITE SAME LENGTH in the BLOCK
   LIMITS VPD.

 - max_write_same_blocks can be overriden per-device basis in sysfs.

 - The UNMAP discovery heuristics remain unchanged but the discard
   limits are tweaked to match the "real" WRITE SAME commands.

 - In the error handling logic we now distinguish between WRITE SAME
   with and without UNMAP set.

The discovery process heuristics are:

 - If the device reports a SCSI level of SPC-3 or greater we'll issue
   READ SUPPORTED OPERATION CODES to find out whether WRITE SAME(16) is
   supported. If that's the case we will use it.

 - If the device supports the block limits VPD and reports a MAXIMUM
   WRITE SAME LENGTH bigger than 0xFFFF we will use WRITE SAME(16).

 - Otherwise we will use WRITE SAME(10) unless the target LBA is beyond
   0xFFFFFFFF or the block count exceeds 0xFFFF.

 - no_write_same is set for ATA, FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 22:45:42 -08:00
Martin K. Petersen 3c6bdaeab4 [SCSI] Add a report opcode helper
The REPORT SUPPORTED OPERATION CODES command can be used to query
whether a given opcode is supported by a device. Add a helper function
that allows us to look up commands.

We only issue RSOC if the device reports compliance with SPC-3 or
later. But to err on the side of caution we disable the command for ATA,
FireWire and USB.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-11-13 21:11:31 -08:00
Paolo Bonzini 1b26d29ccd [libata] scsi: implement MODE SELECT command
The cache_type file in sysfs lets users configure the disk cache in
write-through or write-back modes.  However, ata disks do not support
writing to the file because they do not implement the MODE SELECT
command.

This patch adds a translation from MODE SELECT (for the caching page
only) to the ATA SET FEATURES command.  The set of changeable parameters
answered by MODE SENSE is also adjusted accordingly.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-08-17 14:10:36 -04:00
Paolo Bonzini 6ca8e79466 [libata] scsi: support MODE SENSE request for changeable and default parameters
Since the next patch will introduce support for MODE SELECT, it
makes sense to start advertising which bits are actually changeable.
For now, the answer is none.

Default parameters can also be reported, they are simply the same
as the current parameters.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-08-17 14:09:59 -04:00
Jeff Garzik 3e451a495d [libata] scsi: Remove unlikely() from FUA check
Some other unlikely() should probably be removed as well.  A fresh look
reveals an over-enthusiasm for unlikely() in libata-scsi.c.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-08-17 14:04:50 -04:00
Lin Ming 3bd46600a7 libata-acpi: add ata port runtime D3Cold support
ATA port may support runtime D3Cold state, for example, Zero-power ODD case.
This patch adds wakeup notifier and enable/disable run_wake during
supend/resume.

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-06-29 11:38:13 -04:00
Dan Williams b202445925 [SCSI] libsas, libata: fix start of life for a sas ata_port
This changes the ordering of initialization and probing events from:
  1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
  1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  3/ schedule port probe in DISCE_PROBE

This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:

  BUG: unable to handle kernel paging request at 0000000000003b10
  IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
  ...
  [<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
  [<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
  [<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
  [<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
  [<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]

...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.

Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-04-23 12:11:47 +01:00
Lin Ming f8fc75dc57 [SCSI] libata: Pass correct DMA device to scsi host
Use scsi_add_host_with_dma in ata_scsi_add_hosts to pass in the
correct DMA device(ATA host).

Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2

Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-04-22 19:00:21 +01:00
Dan Williams 85d6725b7c libata: make ata_print_id atomic
This variable is incremented from multiple contexts (module_init via
libata-lldds and the libsas discovery thread).  Make it atomic to head
off any chance of libsas and libata creating duplicate ids.

Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-04-12 15:57:51 -04:00
Dan Williams 9508a66f89 [SCSI] libsas: async ata scanning
libsas ata error handling is already async but this does not help the
scan case.  Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.

Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.

Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.

Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:35:41 -06:00
Lin Ming 9ee4f39339 ata: add ata port runtime PM callbacks
Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.

Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-01-08 19:14:58 -05:00
Lin Ming 9a6d6a2dda ata: make ata port as parent device of scsi host
Currently, the device tree of ata port and scsi host looks as below,

        /sys/devices/pci0000:00/0000:00:1f.2    (ahci controller)
        |-- ata1                                (ata port)
        |-- host0                               (scsi host)
           |-- target0:0:0                      (scsi target)
               |-- 0:0:0:0                      (disk)

This patch makes ata port as parent device of scsi host, then it becomes

        /sys/devices/pci0000:00/0000:00:1f.2    (ahci controller)
        |-- ata1                                (ata port)
            |-- host0                           (scsi host)
                |-- target0:0:0                 (scsi target)
                    |-- 0:0:0:0                 (disk)

With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,

disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.

Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2012-01-08 19:14:57 -05:00
Marcos Paulo de Souza 6d2dd05429 [libata] libata-scsi.c: Add function parameter documentation
Add the documentation of parameters of ata_change_queue_depth to silence the warning of make xmldocs

Signed-off-by: Marcos paulo de Souza <marcos.mage@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-11-09 01:32:27 -05:00
Paul Gortmaker 38789fda29 ide/ata: Add export.h for EXPORT_SYMBOL/THIS_MODULE where needed
They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include export.h explicitly now.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:37 -04:00
Dan Williams f6e67035a9 [SCSI] libsas,libata: fix ->change_queue_{depth|type} for sata devices
Pass queue_depth change requests to libata, and prevent queue_type
changes for ATA devices.

Otherwise:
1/ we do not honor the libata specific restrictions on the queue depth
2/ libsas drivers that do not set sdev->tagged_supported are unable to
   change the queue_depth of ata devices via sysfs

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 12:30:30 -05:00
Joe Perches a9a79dfec2 ata: Convert ata_<foo>_printk(KERN_<LEVEL> to ata_<foo>_<level>
Saves text by removing nearly duplicated text format strings by
creating ata_<foo>_printk functions and printf extension %pV.

ata defconfig size shrinks ~5% (~8KB), allyesconfig ~2.5% (~13KB)

Format string duplication comes from:

 #define ata_link_printk(link, lv, fmt, args...) do { \
       if (sata_pmp_attached((link)->ap) || (link)->ap->slave_link)    \
               printk("%sata%u.%02u: "fmt, lv, (link)->ap->print_id,   \
                      (link)->pmp , ##args); \
       else \
               printk("%sata%u: "fmt, lv, (link)->ap->print_id , ##args); \
       } while(0)

Coalesce long formats.

$ size drivers/ata/built-in.*
   text	   data	    bss	    dec	    hex	filename
 544969	  73893	 116584	 735446	  b38d6	drivers/ata/built-in.allyesconfig.ata.o
 558429	  73893	 117864	 750186	  b726a	drivers/ata/built-in.allyesconfig.dev_level.o
 141328	  14689	   4220	 160237	  271ed	drivers/ata/built-in.defconfig.ata.o
 149567	  14689	   4220	 168476	  2921c	drivers/ata/built-in.defconfig.dev_level.o

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-07-23 17:57:36 -04:00
Nishanth Aravamudan 3f1e046ad3 libata/sas: only set FROZEN flag if new EH is supported
On 16.06.2011 [08:28:39 -0500], Brian King wrote:
> On 06/16/2011 02:51 AM, Tejun Heo wrote:
> > On Wed, Jun 15, 2011 at 04:34:17PM -0700, Nishanth Aravamudan wrote:
> >>> That looks like the right thing to do. For ipr's usage of
> >>> libata, we don't have the concept of a port frozen state, so this flag
> >>> should really never get set. The alternate way to fix this would be to
> >>> only set ATA_PFLAG_FROZEN in ata_port_alloc if ap->ops->error_handler
> >>> is not NULL.
> >>
> >> It seemed like ipr is as you say, but I wasn't sure if it was
> >> appropriate to make the change above in the common libata-scis code or
> >> not. I don't want to break some other device on accident.
> >>
> >> Also, I tried your suggestion, but I don't think that can happen in
> >> ata_port_alloc? ata_port_alloc is allocated ap itself, and it seems like
> >> ap->ops typically gets set only after ata_port_alloc returns?
> >
> > Maybe we can test error_handler in ata_sas_port_start()?
>
> Good point. Since libsas is converted to the new eh now, we would need to have
> this test.

Commit 7b3a24c57d ("ahci: don't enable
port irq before handler is registered") caused a regression for CD-ROMs
attached to the IPR SATA bus on Power machines:

  ata_port_alloc: ENTER
  ata_port_probe: ata1: bus probe begin
  ata1.00: ata_dev_read_id: ENTER
  ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
  ata1.00: ata_dev_read_id: ENTER
  ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
  ata1.00: limiting speed to UDMA7:PIO5
  ata1.00: ata_dev_read_id: ENTER
  ata1.00: failed to IDENTIFY (I/O error, err_mask=0x40)
  ata1.00: disabled
  ata_port_probe: ata1: bus probe end
  scsi_alloc_sdev: Allocation failure during SCSI scanning, some SCSI devices might not be configured

The FROZEN flag added in that commit is only cleared by the new EH code,
which is not used by ipr. Clear this flag in the SAS code if we don't
support new EH.

Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-06-23 16:41:26 -04:00
Linus Torvalds 798ce8f1cc Merge branch 'for-2.6.40/core' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.40/core' of git://git.kernel.dk/linux-2.6-block: (40 commits)
  cfq-iosched: free cic_index if cfqd allocation fails
  cfq-iosched: remove unused 'group_changed' in cfq_service_tree_add()
  cfq-iosched: reduce bit operations in cfq_choose_req()
  cfq-iosched: algebraic simplification in cfq_prio_to_maxrq()
  blk-cgroup: Initialize ioc->cgroup_changed at ioc creation time
  block: move bd_set_size() above rescan_partitions() in __blkdev_get()
  block: call elv_bio_merged() when merged
  cfq-iosched: Make IO merge related stats per cpu
  cfq-iosched: Fix a memory leak of per cpu stats for root group
  backing-dev: Kill set but not used var in  bdi_debug_stats_show()
  block: get rid of on-stack plugging debug checks
  blk-throttle: Make no throttling rule group processing lockless
  blk-cgroup: Make cgroup stat reset path blkg->lock free for dispatch stats
  blk-cgroup: Make 64bit per cpu stats safe on 32bit arch
  blk-throttle: Make dispatch stats per cpu
  blk-throttle: Free up a group only after one rcu grace period
  blk-throttle: Use helper function to add root throtl group to lists
  blk-throttle: Introduce a helper function to fill in device details
  blk-throttle: Dynamically allocate root group
  blk-cgroup: Allow sleeping while dynamically allocating a group
  ...
2011-05-25 09:14:07 -07:00
Martin K. Petersen 5f4e206666 libata: Use Maximum Write Same Length to report discard size limit
Previously we used Maximum Unmap LBA Count in the Block Limits VPD to
signal the maximum number of sectors we could handle in a single Write
Same command.

Starting with SBC3r26 the Block Limits VPD has an explicit limit on the
number of blocks in a Write Same. This means we can stop abusing a field
related to the Unmap command and let our SAT use the proper value in the
VPD (Maximum Write Same Length).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cc: stable@kernel.org
2011-05-19 20:46:01 -04:00
shaohua.li@intel.com 900e599eb0 SATA: enable non-queueable flush flag
Enable non-queueable flush flag for SATA.

Stable: 2.6.39 only

Cc: stable@kernel.org
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2011-05-06 11:36:25 -06:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Hannes Reinecke 6b3b9d73e0 libata: Include WWN ID in inquiry VPD emulation
As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
2011-03-14 02:59:37 -04:00
James Bottomley a29b5dad46 libata: fix locking for sas paths
For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host.  For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code.  However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone).  Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:45 -05:00
James Bottomley 238c9cf9ea libata: plumb sas port scan into standard libata paths
The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths.  This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).

Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-03-02 02:36:45 -05:00
Tejun Heo 729a6a300e libata: set queue DMA alignment to sector size for ATAPI too
ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page.  This
is achieved by setting queue DMA alignment.  If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.

This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors().  Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.

This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size.  While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-01-28 03:16:20 -05:00
Jeff Garzik b27dcfb067 [libata] avoid needlessly passing around ptr to SCSI completion func
It's stored in struct scsi_cmnd->scsi_done, making several 'done'
parameters to functions redundant.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-01-05 19:43:22 -05:00
Jeff Garzik 23e701e620 [libata] remove SCSI host lock and serial number usage from ata_scsi_queuecmd
cmd->serial_number is never tested in any path we reach; therefore we may
remove the call to scsi_cmd_get_serial() inside DEF_SCSI_QCMD, the SCSI
host_lock acquisition surrounding it, and our own SCSI host_lock
unlock+relock cycle.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-11-17 12:03:58 -05:00
Jeff Garzik f281233d3e SCSI host lock push-down
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.

The patch below presents a simple SCSI host lock push-down as an
equivalent transformation.  No locking or other behavior should change
with this patch.  All existing bugs and locking orders are preserved.

Additionally, add one parameter to queuecommand,
	struct Scsi_Host *
and remove one parameter from queuecommand,
	void (*done)(struct scsi_cmnd *)

Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.

Minimal code disturbance was attempted with this change.  Most drivers
needed only two one-line modifications for their host lock push-down.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-11-16 13:33:23 -08:00
Tejun Heo 2a5f07b5ec libata: fix NULL sdev dereference race in atapi_qc_complete()
SCSI commands may be issued between __scsi_add_device() and dev->sdev
assignment, so it's unsafe for ata_qc_complete() to dereference
dev->sdev->locked without checking whether it's NULL or not.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-11-12 17:10:51 -05:00
Martin K. Petersen 02e0a60477 libata: Signal that our SATL supports WRITE SAME(16) with UNMAP
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic.  Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:05 -04:00
Tejun Heo 6b7ae9545a libata: reimplement link power management
The current LPM implementation has the following issues.

* Operation order isn't well thought-out.  e.g. HIPM should be
  configured after IPM in SControl is properly configured.  Not the
  other way around.

* Suspend/resume paths call ata_lpm_enable/disable() which must only
  be called from EH context directly.  Also, ata_lpm_enable/disable()
  were called whether LPM was in use or not.

* Implementation is per-port when it should be per-link.  As a result,
  it can't be used for controllers with slave links or PMP.

* LPM state isn't managed consistently.  After a link reset for
  whatever reason including suspend/resume the actual LPM state would
  be reset leaving ap->lpm_policy inconsistent.

* Generic/driver-specific logic boundary isn't clear.  Currently,
  libahci has to mangle stuff which libata EH proper should be
  handling.  This makes the implementation unnecessarily complex and
  fragile.

* Tied to ALPM.  Doesn't consider DIPM only cases and doesn't check
  whether the device allows HIPM.

* Error handling isn't implemented.

Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense.  This patch reimplements
LPM support.

* The new implementation is per-link.  The target policy is still
  port-wide (ap->target_lpm_policy) but all the mechanisms and states
  are per-link and integrate well with the rest of link abstraction
  and can work with slave and PMP links.

* Core EH has proper control of LPM state.  LPM state is reconfigured
  when and only when reconfiguration is necessary.  It makes sure that
  LPM state is reset when probing for new device on the link.
  Controller agnostic logic is now implemented in libata EH proper and
  driver implementation only has to deal with controller specifics.

* Proper error handling.  LPM config failure is attributed to the
  device on the link and LPM is disabled for the link if it fails
  repeatedly.

* ops->enable/disable_pm() are replaced with single ops->set_lpm()
  which takes @policy and @hints.  This simplifies driver specific
  implementation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:04 -04:00
Tejun Heo c93b263e0d libata: clean up lpm related symbols and sysfs show/store functions
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm.  This patch cleans up lpm related symbols
and sysfs show/store functions as follows.

* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
  MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
  ATA_LPM_{MIN|MAX|MED}_POWER.

* Pre/postfixes are unified to lpm.

* sysfs show/store functions for link_power_management_policy were
  curiously named get/put and unnecessarily complex.  Renamed to
  show/store and simplified.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:04 -04:00
Grant Grundler 295124dce4 [libata] support for > 512 byte sectors (e.g. 4K Native)
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.

When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
  http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors

Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.

Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.

Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:03 -04:00
Gwendal Grignou d9027470b8 [libata] Add ATA transport class
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.

Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-10-21 20:21:03 -04:00
Linus Torvalds 2f9e825d3e Merge branch 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
  block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
  xen-blkfront: fix missing out label
  blkdev: fix blkdev_issue_zeroout return value
  block: update request stacking methods to support discards
  block: fix missing export of blk_types.h
  writeback: fix bad _bh spinlock nesting
  drbd: revert "delay probes", feature is being re-implemented differently
  drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
  drbd: Disable delay probes for the upcomming release
  writeback: cleanup bdi_register
  writeback: add new tracepoints
  writeback: remove unnecessary init_timer call
  writeback: optimize periodic bdi thread wakeups
  writeback: prevent unnecessary bdi threads wakeups
  writeback: move bdi threads exiting logic to the forker thread
  writeback: restructure bdi forker loop a little
  writeback: move last_active to bdi
  writeback: do not remove bdi from bdi_list
  writeback: simplify bdi code a little
  writeback: do not lose wake-ups in bdi threads
  ...

Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
2010-08-10 15:22:42 -07:00
Christoph Hellwig 7b6d91daee block: unify flags for struct bio and struct request
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver.  There were two flags in the bio that were
missing in the requests:  BIO_RW_UNPLUG and BIO_RW_AHEAD.  Also I've
renamed two request flags that had a superflous RW in them.

Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-08-07 18:20:39 +02:00
Christoph Hellwig 33659ebbae block: remove wrappers for request type/flags
Remove all the trivial wrappers for the cmd_type and cmd_flags fields in
struct requests.  This allows much easier grepping for different request
types instead of unwinding through macros.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-08-07 18:17:56 +02:00
Tejun Heo ad72cf9885 libata: take advantage of cmwq and remove concurrency limitations
libata has two concurrency related limitations.

a. ata_wq which is used for polling PIO has single thread per CPU.  If
   there are multiple devices doing polling PIO on the same CPU, they
   can't be executed simultaneously.

b. ata_aux_wq which is used for SCSI probing has single thread.  In
   cases where SCSI probing is stalled for extended period of time
   which is possible for ATAPI devices, this will stall all probing.

#a is solved by increasing maximum concurrency of ata_wq.  Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.

#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
2010-07-02 10:59:24 +02:00
Tejun Heo d8d9129ea2 libata: implement on-demand HPA unlocking
Implement ata_scsi_unlock_native_capacity() which will be called
through SCSI layer when block layer notices that partitions on a
device extend beyond the end of the device.  It requests EH to unlock
HPA, waits for completion and returns the current device capacity.

This allows libata to unlock HPA on demand instead of having to decide
whether to unlock upfront.  Unlocking on demand is safer than
unlocking by upfront because some BIOSes write private data to the
area beyond HPA limit.  This was suggested by Ben Hutchings.

Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-06-02 13:50:10 -04:00
Tejun Heo 3e4ec3443f libata: kill ATA_FLAG_DISABLED
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken.  Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.

Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead.  ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.

This simplifies condition check in IRQ handlers.  While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-05-17 22:49:02 -04:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Martin K. Petersen 086fa5ff08 block: Rename blk_queue_max_sectors to blk_queue_max_hw_sectors
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.

Also introduce a temporary wrapper for backwards compability.  This can
be removed after the merge window is closed.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2010-02-26 13:58:08 +01:00
Douglas Gilbert bc496ed00a libata-scsi passthru: fix bug which truncated LBA48 return values
Fix assignment which overwrote SAT ATA PASS-THROUGH command EXTEND
bit setting (ATA_TFLAG_LBA48)

Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2010-02-04 01:01:22 -05:00
Christoph Hellwig 0cdd6eb7e0 libata: use the WRITE_SAME_16 define
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-17 01:02:09 -05:00
Linus Torvalds 382f51fe2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
  [SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
  [SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
  [SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
  [SCSI] zfcp: Update FSF error reporting
  [SCSI] zfcp: Improve ELS ADISC handling
  [SCSI] zfcp: Simplify handling of ct and els requests
  [SCSI] zfcp: Remove ZFCP_DID_MASK
  [SCSI] zfcp: Move WKA port to zfcp FC code
  [SCSI] zfcp: Use common code definitions for FC CT structs
  [SCSI] zfcp: Use common code definitions for FC ELS structs
  [SCSI] zfcp: Update FCP protocol related code
  [SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
  [SCSI] zfcp: Assign scheduled work to driver queue
  [SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
  [SCSI] zfcp: Implement module unloading
  [SCSI] zfcp: Merge trace code for fsf requests in one function
  [SCSI] zfcp: Access ports and units with container_of in sysfs code
  [SCSI] zfcp: Remove suspend callback
  [SCSI] zfcp: Remove global config_mutex
  [SCSI] zfcp: Replace local reference counting with common kref
  ...
2009-12-09 19:42:25 -08:00
Mike Christie e881a172da [SCSI] modify change_queue_depth to take in reason why it is being called
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.

This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>

[Vasu.Dev: v2
	Also converted pmcraid_change_queue_depth and then verified
all modules compile  using "make allmodconfig" for any new build
warnings on X86_64.

	Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
2009-12-04 12:00:41 -06:00
Martin K. Petersen d0634c4aea libata: Clarify ata_set_lba_range_entries function
ata_set_lba_range_entries used the variable max for two different things
which was confusing.  Make the function take a buffer size in bytes as
argument and return the used buffer size upon completion.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 18:01:23 -05:00
Martin K. Petersen e78db4dfb1 libata: Report zeroed read after TRIM and max discard size
Our current TRIM payload is a single sector that can accommodate 64 *
65535 blocks being unmapped.  Report this value in the Block Limits
Maximum Unmap LBA count field.

If a storage device supports TRIM and the DRAT and RZAT bits are set,
report TPRZ=1 in Read Capacity(16).

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 18:01:04 -05:00
Christoph Hellwig 18f0f97850 libata: add translation for SCSI WRITE SAME (aka TRIM support)
Add support for the ATA TRIM command in libata.  We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.

Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Matthew Garrett 6a74463798 ata: Don't require newlines for link_power_management_policy
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-12-03 02:46:35 -05:00
Tejun Heo bd30add88c libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
ata_scsi_pass_thru() was checking for input sanity and disallowed
commands while initializaing qc from scmd.  TPM filtering was added
right after protocol check at which point tf wasn't initialized
properly.  This means that TPM filtering has never really worked.

This patch fixes the bug by reorganizing ata_scsi_pass_thru() such
that qc is fully initialized before checking for invalid conditions
which is way less error prone.

Discovered while Thilo-Alexander Ginkel was trying debug patches for
bko#13416.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Thilo-Alexander Ginkel <thilo@ginkel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-08 21:17:43 -04:00
Martin K. Petersen f17259a312 libata: Delegate nonrot flag setting to SCSI
Now that the SCSI disk driver correctly handles non-rotational devices
we can move setting the queue flag to SCSI.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-01 19:47:20 -04:00
Tejun Heo 051d9fbdd1 libata: remove spindown skipping and warning
This was a hack to give userland shutdown tools time to drop manual
spindown.  All popular distros updated quite some time ago and the due
is well passed.  Drop it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-09-01 19:47:20 -04:00
Jens Axboe e4b636366c Merge branch 'master' into for-2.6.31
Conflicts:
	drivers/block/hd.c
	drivers/block/mg_disk.c

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-22 20:25:34 +02:00
Martin K. Petersen 4bca328643 libata: Media rotation rate and form factor heuristics
This patch provides new heuristics for parsing both the form factor and
media rotation rate ATA IDENFITY words.

The reported ATA version must be 7 or greater and the device must return
values defined as valid in the standard.  Only then are the
characteristics reported to SCSI via the VPD B1 page.

This seems like a reasonable compromise to me considering that we have
been shipping several kernel releases that key off the rotation rate bit
without any version checking whatsoever.  With no complaints so far.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-05-15 14:14:56 -04:00
Martin K. Petersen 61d79a8eb3 libata: Report disk alignment and physical block size
For disks with 4KB sectors, report the correct block size and alignment
when filling out the READ CAPACITY(16) response.

This patch is based upon code from Matthew Wilcox' 4KB ATA tree.  I
fixed the bug I reported a while back caused by ATA and SCSI using
different approaches to describing the alignment.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-05-15 14:14:22 -04:00
Vitaly Mayatskikh ea7a5ed58f Avoid world-writable sysfs files in libata driver.
Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-05-11 14:31:31 -04:00
Tejun Heo b079041030 block: cleanup rq->data_len usages
With recent unification of fields, it's now guaranteed that
rq->data_len always equals blk_rq_bytes().  Convert all non-IDE direct
users to accessors.  IDE will be converted in a separate patch.

Boaz: spotted incorrect data_len/resid_len conversion in osd.

[ Impact: convert direct rq->data_len usages to blk_rq_bytes() ]

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2009-05-11 09:50:55 +02:00
Alan Cox e3cf95dd6d ata: Report 16/32bit PIO as best we can
The legacy old IDE ioctl API for this is a bit primitive so we try
and map stuff sensibly onto it.

- Set PIO over DMA devices to report 32bit
- Add ability to change the PIO32 settings if the controller permits it
- Add that functionality into the sff drivers
- Add that functionality into the VLB legacy driver
- Turn on the 32bit PIO on the ninja32 and add support there

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-04-16 15:28:23 -04:00
Randy Dunlap 5eb66fe05f libata: fix kernel-doc warnings
Fix libata kernel-doc warnings:

Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:45 -05:00
Rafael J. Wysocki 2a6e58d273 SATA: Blacklisting of systems that spin off disks during ACPI power off
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:49 -05:00
Jeff Garzik 94be9a58d7 [libata] get-identity ioctl: Fix use of invalid memory pointer
for SAS drivers.

Caught by Ke Wei (and team?) at Marvell.

Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.

Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:17:09 -05:00
Kay Sievers b9d5fc41dc libata: struct device - replace bus_id with dev_name(), dev_set_name()
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-06 10:44:43 -08:00
Linus Torvalds 590cf28580 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (104 commits)
  [SCSI] fcoe: fix configuration problems
  [SCSI] cxgb3i: fix select/depend problem
  [SCSI] fcoe: fix incorrect use of struct module
  [SCSI] cxgb3i: remove use of skb->sp
  [SCSI] cxgb3i: Add cxgb3i iSCSI driver.
  [SCSI] zfcp: Remove unnecessary warning message
  [SCSI] zfcp: Add support for unchained FSF requests
  [SCSI] zfcp: Remove busid macro
  [SCSI] zfcp: remove DID_DID flag
  [SCSI] zfcp: Simplify mask lookups for incoming RSCNs
  [SCSI] zfcp: Remove initial device data from zfcp_data
  [SCSI] zfcp: fix compile warning
  [SCSI] zfcp: Remove adapter list
  [SCSI] zfcp: Simplify SBAL allocation to fix sparse warnings
  [SCSI] zfcp: register with SCSI layer on ccw registration
  [SCSI] zfcp: Fix message line break
  [SCSI] qla2xxx: changes in multiq code
  [SCSI] eata: fix the data buffer accessors conversion regression
  [SCSI] ibmvfc: Improve async event handling
  [SCSI] lpfc : correct printk types on PPC compiles
  ...
2008-12-30 17:43:10 -08:00
FUJITA Tomonori f4f4e47e4a [SCSI] add residual argument to scsi_execute and scsi_execute_req
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-12-29 11:24:24 -06:00
Tejun Heo 1eca4365be libata: beef up iterators
There currently are the following looping constructs.

* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order

Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link.  Instead of adding another one with long name, do the following
cleanup.

* Implement and export ata_link_next() and ata_dev_next() which take
  @mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
  looping mode explicitly.

The following iteration modes are implemented.

* ATA_LITER_EDGE		: loop over edge links
* ATA_LITER_HOST_FIRST		: loop over all links, host link first
* ATA_LITER_PMP_FIRST		: loop over all links, PMP links first

* ATA_DITER_ENABLED		: loop over enabled devices
* ATA_DITER_ENABLED_REVERSE	: loop over enabled devices in reverse order
* ATA_DITER_ALL			: loop over all devices
* ATA_DITER_ALL_REVERSE		: loop over all devices in reverse order

This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-28 22:43:20 -05:00
Tejun Heo 8a8bc22332 libata: revert convert-to-block-tagging patches
This patch reverts the following three commits which convert libata to
use block layer tagging.

 43a49cbdf3
 e013e13bf6
 2fca5ccf97

Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.

The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands.  Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made.  I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.

So, for the time being, keep using the old dumb in-libata qc
allocation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-11-10 08:04:47 -08:00
Elias Oltmanns a464189de3 libata: Fix a potential race condition in ata_scsi_park_show()
Peter Moulder has pointed out that there is a slight chance that a
negative value might be passed to jiffies_to_msecs() in
ata_scsi_park_show(). This is fixed by saving the value of jiffies in a
local variable, thus also reducing code since the volatile variable
jiffies is accessed only once.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Tejun Heo <tj.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-04 01:08:24 -05:00
Jens Axboe 43a49cbdf3 libata: fix NCQ devices behind port multipliers
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-27 19:25:30 +01:00
Jens Axboe e013e13bf6 libata: fix bug with non-ncq devices
The recent commit 2fca5ccf97 ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices

The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list.  So we need to check for
-1 first and only use the tag field if it's valid.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-24 08:22:38 -07:00
Jens Axboe 2fca5ccf97 libata: switch to using block layer tagging support
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-23 16:05:26 -07:00
Bartlomiej Zolnierkiewicz a4f19040a3 libata: WIN_* -> ATA_CMD_*
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-10-10 22:39:20 +02:00
Linus Torvalds e26feff647 Merge branch 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.28' of git://git.kernel.dk/linux-2.6-block: (132 commits)
  doc/cdrom: Trvial documentation error, file not present
  block_dev: fix kernel-doc in new functions
  block: add some comments around the bio read-write flags
  block: mark bio_split_pool static
  block: Find bio sector offset given idx and offset
  block: gendisk integrity wrapper
  block: Switch blk_integrity_compare from bdev to gendisk
  block: Fix double put in blk_integrity_unregister
  block: Introduce integrity data ownership flag
  block: revert part of d7533ad0e132f92e75c1b2eb7c26387b25a583c1
  bio.h: Remove unused conditional code
  block: remove end_{queued|dequeued}_request()
  block: change elevator to use __blk_end_request()
  gdrom: change to use __blk_end_request()
  memstick: change to use __blk_end_request()
  virtio_blk: change to use __blk_end_request()
  blktrace: use BLKTRACE_BDEV_SIZE as the name size for setup structure
  block: add lld busy state exporting interface
  block: Fix blk_start_queueing() to not kick a stopped queue
  include blktrace_api.h in headers_install
  ...
2008-10-10 10:52:45 -07:00
Jens Axboe 8bff7c6b0f libata: set queue SSD flag for SSD devices
SSD devices should give an RPM setting of 1 in word 217 of the ID
page. If we see such a device, tell the block layer about it.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-10-09 08:56:19 +02:00
Elias Oltmanns 45fabbb77b libata: Implement disk shock protection support
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.

Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-29 00:27:54 -04:00
Tejun Heo 2486fa561a libata: update atapi disable handling
Global and per-LLD ATAPI disable checks were done in the command issue
path probably because it was left out during EH conversion.  On
affected machines, this can cause lots of warning messages.  Move them
to where they belong - the probing path.

Reported by Chunbo Luo.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-31 01:47:05 -04:00
Linus Torvalds b312bf359e Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  AHCI: Remove an unnecessary flush from ahci_qc_issue
  AHCI: speed up resume
  [libata] Add support for VPD page b1
  ata: endianness annotations in pata drivers
  libata-eh: update atapi_eh_request_sense() to take @dev instead of @qc
  [libata] sata_svw: update code comments relating to data corruption
  libata/ahci: enclosure management support
  libata: improve EH internal command timeout handling
  libata: use ULONG_MAX to terminate reset timeout table
  libata: improve EH retry delay handling
  libata: consistently use msecs for time durations
2008-07-15 11:18:10 -07:00
Matthew Wilcox 1e9dbc9291 [libata] Add support for VPD page b1
SCSI VPD page b1 reports the nominal rotation speed and physical size
of the device.  Devices that conform to ATA-8 can return this information
in words 217 and 168 of the identify data.

Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
Kristen Carlson Accardi 18f7ba4c2f libata/ahci: enclosure management support
Add Enclosure Management support to libata and ahci.

Signed-off-by:  Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:33 -04:00
FUJITA Tomonori 27f8221af4 block: add blk_queue_update_dma_pad
This adds blk_queue_update_dma_pad to prevent LLDs from overwriting
the dma pad mask wrongly (we added blk_queue_update_dma_alignment due
to the same reason).

This also converts libata to use blk_queue_update_dma_pad instead of
blk_queue_dma_pad.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-07-04 09:52:13 +02:00
Tejun Heo 5895ef9a5b libata: don't check whether to use DMA or not for no data commands
There's no reason to check whether to use DMA or not for no data
commands.  Don't do it.  While at it, make local variable using_pio in
atapi_xlat() set iff ATAPI_PROT_PIO is going to be used and rename
ata_check_atapi_dma() to atapi_check_dma() for consistency.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-18 20:27:49 -04:00
Randy Dunlap ec2a20e619 libata: fix libata-scsi kernel-doc notation
Fix libata-scsi kernel-doc notation:

Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1659): No description found for parameter 'cmd'
Warning(linux-2.6.25-git15//drivers/ata/libata-scsi.c:1971): No description found for parameter 'buf'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-30 12:37:50 -04:00
Tejun Heo 50af2fa1e1 libata: ignore SIMG4726 config pseudo device
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device.  This makes the device completely ignored by
libata.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-19 17:51:48 -04:00
Tejun Heo 87340e9834 libata-scsi: improve rbuf handling for simulated commands
Buffer length handling in simulated commands is error-prone and full
of bugs.  There are a number of places where necessary length checks
are missing and if the output buffer is passed in as sglist, nothing
works.

This patch adds a static buffer ata_scsi_rbuf which is sufficiently
large to handle the larges output from simulated commands (4k
currently), let all simulte functions write to the buffer and removes
all length checks as we know that there always is enough buffer space.
Copying in (for ATAPI inquiry fix up) and out are handled by
sg_copy_to/from_buffer() behind ata_scsi_rbuf_get/put() interface
which handles sglist properly.

This patch is inspired from buffer length check fix patch from Petr
Vandrovec.

Updated to use sg_copy_to/from_buffer() as suggested by FUJITA
Tomonori.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vmware.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:17:03 -04:00
Tejun Heo f0761be344 libata-scsi: clean up inquiry / mode sense related functions
* make ata_scsiop_*() static
* make ata_scsi_set_sense() static and move it above its users
* make ata_scsi_rbuf_fill() static
* kill unused ata_scsi_badcmd()

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-29 02:16:37 -04:00
Tony Jones ee959b00c3 SCSI: convert struct class_device to struct device
It's big, but there doesn't seem to be a way to split it up smaller...

Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-19 19:10:33 -07:00
Linus Torvalds 2cca775bae Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (137 commits)
  [SCSI] iscsi: bidi support for iscsi_tcp
  [SCSI] iscsi: bidi support at the generic libiscsi level
  [SCSI] iscsi: extended cdb support
  [SCSI] zfcp: Fix error handling for blocked unit for send FCP command
  [SCSI] zfcp: Remove zfcp_erp_wait from slave destory handler to fix deadlock
  [SCSI] zfcp: fix 31 bit compile warnings
  [SCSI] bsg: no need to set BSG_F_BLOCK bit in bsg_complete_all_commands
  [SCSI] bsg: remove minor in struct bsg_device
  [SCSI] bsg: use better helper list functions
  [SCSI] bsg: replace kobject_get with blk_get_queue
  [SCSI] bsg: takes a ref to struct device in fops->open
  [SCSI] qla1280: remove version check
  [SCSI] libsas: fix endianness bug in sas_ata
  [SCSI] zfcp: fix compiler warning caused by poking inside new semaphore (linux-next)
  [SCSI] aacraid: Do not describe check_reset parameter with its value
  [SCSI] aacraid: Fix down_interruptible() to check the return value
  [SCSI] sun3_scsi_vme: add MODULE_LICENSE
  [SCSI] st: rename flush_write_buffer()
  [SCSI] tgt: use KMEM_CACHE macro
  [SCSI] initio: fix big endian problems for auto request sense
  ...
2008-04-18 11:25:31 -07:00
James Bottomley 855d854a33 libata: fix boot panic with SATAPI devices on non-SFF HBAs
The kernel now panics reliably on boot if you have a SATAPI device
connected.

The problem was introduced by the libata merge trying to pull out all
the SFF code into a separate module.  Unfortunately, if you're a satapi
device you usually need to call atapi_request_sense, which has a bare
invocation of a SFF callback which is NULL on non-SFF HBAs.  Fix this by
making the call conditional.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-18 11:20:42 -07:00
Tejun Heo 071f44b1d2 libata: implement PMP helpers
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link.  While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.

This change simplifies LLDs and helps making PMP support optional.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:25 -04:00
Tejun Heo 127102aea2 libata: make SFF support optional
Now that SFF support is completely separated out from the core layer,
it can be made optional.  Add CONFIG_ATA_SFF and let SFF drivers
depend on it.  If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled.  This saves good
number of bytes for small systems.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:24 -04:00
Tejun Heo 5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo b558edddb1 libata: kill ata_ehi_schedule_probe()
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic.  Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it.  This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.

While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency.  Setting extra bits in the probe_mask
doesn't hurt anybody.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo 672b2d65ba libata: kill ATA_EHI_RESUME_LINK
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested.  The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.

As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo cf48062658 libata: prefer hardreset
When both soft and hard resets are available, libata preferred
softreset till now.  The logic behind it was to be softer to devices;
however, this doesn't really help much.  Rationales for the change:

* BIOS may freeze lock certain things during boot and softreset can't
  unlock those.  This by itself is okay but during operation PHY event
  or other error conditions can trigger hardreset and the device may
  end up with different configuration.

  For example, after a hardreset, previously unlockable HPA can be
  unlocked resulting in different device size and thus revalidation
  failure.  Similar condition can occur during or after resume.

* Certain ATAPI devices require hardreset to recover after certain
  error conditions.  On PATA, this is done by issuing the DEVICE RESET
  command.  On SATA, COMRESET has equivalent effect.  The problem is
  that DEVICE RESET needs its own execution protocol.

  For SFF controllers with bare TF access, it can be easily
  implemented but more advanced controllers (e.g. ahci and sata_sil24)
  require specialized implementations.  Simply using hardreset solves
  the problem nicely.

* COMRESET initialization sequence is the norm in SATA land and many
  SATA devices don't work properly if only SRST is used.  For example,
  some PMPs behave this way and libata works around by always issuing
  hardreset if the host supports PMP.

  Like the above example, libata has developed a number of mechanisms
  aiming to promote softreset to hardreset if softreset is not going
  to work.  This approach is time consuming and error prone.

  Also, note that, dependingon how you read the specs, it could be
  argued that PMP fan-out ports require COMRESET to start operation.
  In fact, all the PMPs on the market except one don't work properly
  if COMRESET is not issued to fan-out ports after PMP reset.

* COMRESET is an integral part of SATA connection and any working
  device should be able to handle COMRESET properly.  After all, it's
  the way to signal hardreset during reboot.  This is the most used
  and recommended (at least by the ahci spec) method of resetting
  devices.

So, this patch makes libata prefer hardreset over softreset by making
the following changes.

* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
  ATA_EH_{SOFT|HARD}RESET used to be used.  ATA_EH_{SOFT|HARD}RESET is
  now only used to tell prereset whether soft or hard reset will be
  issued.

* Strip out now unneeded promote-to-hardreset logics from
  ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
  other places.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:15 -04:00
FUJITA Tomonori 526917641a [SCSI] libata: use scsi_build_sense_buffer
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 12:19:02 -05:00
Tejun Heo aacda37538 libata: implement ata_qc_raw_nbytes()
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-24 22:09:12 -04:00
Tejun Heo e3790c7d42 block: separate out padding from alignment
Block layer alignment was used for two different purposes - memory
alignment and padding.  This causes problems in lower layers because
drivers which only require memory alignment ends up with adjusted
rq->data_len.  Separate out padding such that padding occurs iff
driver explicitly requests it.

Tomo: restorethe code to update bio in blk_rq_map_user
      introduced by the commit 40b01b9bbd
      according to padding alignment.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-03-04 11:18:17 +01:00
FUJITA Tomonori 7a85f8896f block: restore the meaning of rq->data_len to the true data length
The meaning of rq->data_len was changed to the length of an allocated
buffer from the true data length. It breaks SG_IO friends and
bsg. This patch restores the meaning of rq->data_len to the true data
length and adds rq->extra_len to store an extended length (due to
drain buffer and padding).

This patch also removes the code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd.
The commit adjusts bio according to memory alignment
(queue_dma_alignment). However, memory alignment is NOT padding
alignment. This adjustment also breaks SG_IO friends and bsg. Padding
alignment needs to be fixed in a proper way (by a separate patch).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
2008-03-04 11:17:11 +01:00
Jeff Garzik b445c56815 [libata] wrap kmap_atomic(KM_IRQ0) with local_irq_save/restore()
Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-02-29 19:10:51 -05:00
Tejun Heo 9116300634 libata: automatically use DMADIR if drive/bridge requires it
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-24 00:27:33 -05:00
Randy Dunlap 73fd8b6d31 libata: fix kernel-doc parameter warning
Fix libata kernel-doc parameter:

Warning(linux-2.6.25-rc2-git3//drivers/ata/libata-scsi.c:845): No description found for parameter 'rq'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-20 12:20:49 -05:00
James Bottomley fa2fc7f481 libata: implement drain buffers
This just updates the libata slave configure routine to take advantage
of the block layer drain buffers.  It also adjusts the size lengths in
the atapi code to add the drain buffer to the DMA length so the driver
knows it can rely on it.

I suspect I should also be checking for AHCI as well as ATA_DEV_ATAPI,
but I couldn't see how to do that easily.

tj: * atapi_drain_needed() added such that draining is applied to only
      misc ATAPI commands.
    * q->bounce_gfp used when allocating drain buffer.
    * Now duplicate ATAPI PIO drain logic dropped.
    * ata_dev_printk() used instead of sdev_printk().

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-02-19 11:36:57 +01:00
James Bottomley dde2020754 libata: eliminate the home grown dma padding in favour of
that provided by the block layer

ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis.  However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary.  Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length.  The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.

Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary.  Note that this aligment only applies to transfers
coming in from user space.  However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.

tj: * Adjusting sg after padding is done in block layer.  Make libata
      set queue alignment correctly for ATAPI devices and drop broken
      sg mangling from ata_sg_setup().
    * Use request->raw_data_len for ATAPI transfer chunk size.
    * Killed qc->raw_nbytes.
    * Separated out killing qc->n_iter.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2008-02-19 11:36:56 +01:00
Harvey Harrison 08f01058fe ata: make ata_scsiop_inq_89 static in libata-scsi.c
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-02-15 13:50:53 -05:00
Linus Torvalds 9b73e76f3c Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
  [SCSI] usbstorage: use last_sector_bug flag universally
  [SCSI] libsas: abstract STP task status into a function
  [SCSI] ultrastor: clean up inline asm warnings
  [SCSI] aic7xxx: fix firmware build
  [SCSI] aacraid: fib context lock for management ioctls
  [SCSI] ch: remove forward declarations
  [SCSI] ch: fix device minor number management bug
  [SCSI] ch: handle class_device_create failure properly
  [SCSI] NCR5380: fix section mismatch
  [SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
  [SCSI] IB/iSER: add logical unit reset support
  [SCSI] don't use __GFP_DMA for sense buffers if not required
  [SCSI] use dynamically allocated sense buffer
  [SCSI] scsi.h: add macro for enclosure bit of inquiry data
  [SCSI] sd: add fix for devices with last sector access problems
  [SCSI] fix pcmcia compile problem
  [SCSI] aacraid: add Voodoo Lite class of cards.
  [SCSI] aacraid: add new driver features flags
  [SCSI] qla2xxx: Update version number to 8.02.00-k7.
  [SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
  ...
2008-01-25 17:19:08 -08:00
James Bottomley d0ad3bc97c [SCSI] libata: fix corruption induced by relaxed DMA alignment in SCSI
Hugh Dickens noticed that SMART commands issued from user space can
end up corupting memory.  The problem occurs if the buffer used to
read data spans two pages.  The reason is that the PIO sector routines
in libata are expecting physically contiguous pages when they do
sector operations, so the left overs on the second page go into the
next physically adjacent page rather than the next page in the sg
mapping.

Fix this by enforcing strict 512 byte alignment on all buffers from
userspace.

Acked-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-23 11:27:54 -06:00
James Bottomley 7ccd720da3 [libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:17 -05:00
akpm@linux-foundation.org cadb7345d9 [libata] Prefer SCSI_SENSE_BUFFERSIZE to sizeof()
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:16 -05:00
Al Viro 4ca4e43964 libata annotations and fixes
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:15 -05:00
Tejun Heo ff2aeb1eb6 libata: convert to chained sg
libata used private sg iterator to handle padding sg.  Now that sg can
be chained, padding can be handled using standard sg ops.  Convert to
chained sg.

* s/qc->__sg/qc->sg/

* s/qc->pad_sgent/qc->extra_sg[]/.  Because chaining consumes one sg
  entry.  There need to be two extra sg entries.  The renaming is also
  for future addition of other extra sg entries.

* Padding setup is moved into ata_sg_setup_extra() which is organized
  in a way that future addition of other extra sg entries is easy.

* qc->orig_n_elem is unused and removed.

* qc->n_elem now contains the number of sg entries that LLDs should
  map.  qc->mapped_n_elem is added to carry the original number of
  mapped sgs for unmapping.

* The last sg of the original sg list is used to chain to extra sg
  list.  The original last sg is pointed to by qc->last_sg and the
  content is stored in qc->saved_last_sg.  It's restored during
  ata_sg_clean().

* All sg walking code has been updated.  Unnecessary assertions and
  checks for conditions the core layer already guarantees are removed.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:14 -05:00
Tejun Heo 0dc36888d4 libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion.  Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:14 -05:00
Tejun Heo 93f8fecbe7 libata: make atapi_request_sense() use sg
atapi_request_sense() is now the only left user of ata_sg_init_one().
Convert it to use sg interface.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:13 -05:00
Alan Cox ae8d4ee7ff libata: Disable ATA8-ACS proposed Trusted Computing features by default
Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.

Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
  in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test

While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)

Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.

Signed-off-by: Alan Cox <alan@redhat.com>
2008-01-23 05:24:09 -05:00
Tejun Heo d8cf5389bd libata: relocate sdev->manage_start_stop configuration
After 9b8e8de7, manage_start_stop configuration depends on valid ATA
device.  Move it into ata_scsi_dev_config().  This was detected by the
coverity checker.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-14 21:11:02 -05:00
James Bottomley 465ff3185e [SCSI] relax scsi dma alignment
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes.  I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.

The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev.  (basically all inquiries it
issues can now be directly mapped).

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 18:29:22 -06:00
Ondrej Zary 9b8e8de7e5 libata and starting/stopping ATAPI floppy devices
Prevent libata from starting/stopping non-ATA devices (like ATAPI floppy
drives) as they don't seem to like it:

sd 1:0:1:0: [sdb] Starting disk
ata2.01: configured for PIO2
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0x2 [current]
sd 1:0:1:0: [sdb] ASC=0x3a ASCQ=0x0

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-10 17:13:19 -05:00
Tejun Heo e190222d04 libata: bump transfer chunk size if it's odd
None of the drives I have follows what the standard says about
transfer chunk size.  Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.

According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended.  However, in reality, none of the
drives I have does that.  They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.

In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA.  Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes.  This causes data corruption and buffer
overruns.

This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte.  This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-26 11:03:40 -05:00
Mark Lord 607126c2a2 libata-scsi: be tolerant of 12-byte ATAPI commands in 16-byte CDBs
Sebastian Kemper reported that issuing CD/DVD commands under libata is
not fully compatible with ide-scsi.  In particular, the
GPCMD_SET_STREAMING was being rejected at the host level in some
instances.

The reason is that libata-scsi insists upon the cmd_len field exactly
matching the SCSI opcode being issued, whereas ide-scsi tolerates
12-byte commands contained within a 16-byte (cmd_len) CDB.

There doesn't seem to be a good reason for us to not be compatible
there, so here is a patch to fix libata-scsi to permit SCSI opcodes so
long as they fit within whatever size CDB is provided.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
2007-11-19 12:28:11 +09:00
Jeff Garzik f26792d5c6 [libata] Utilize new SCSI event infrastructure
An end to CD-ROM polling (if you have a device that supports AN)...
hooray!

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-11-03 22:23:02 -04:00
Adrian Bunk a2d6ed149c make ata_scsi_lpm_get() static
ata_scsi_lpm_get() can become static.

Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-11-03 08:46:29 -04:00
Tejun Heo e027bd36c1 libata: implement and use ATA_QCFLAG_QUIET
Implement ATA_QCFLAG_QUIET which indicates that there's no need to
report if the command fails with AC_ERR_DEV and set it for passthrough
commands.

Combined with previous changes, this now makes device errors for all
direct commands reported directly to the issuer without going through
EH actions and reporting.

Note that EH is still invoked after non-IO device errors to determine
the nature of the error and resume command execution (some controller
requires special care after error to continue).  It just performs
default maintenance after error, examines what's going on, realizes
that it's none of its business and reports the command failure without
logging any error messages.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30 09:59:43 -04:00
Tejun Heo b666da35d9 libata: flush is an IO command
ATA_QCFLAG_IO is used to mark commands which are used to perform
regluar IO transfers via block layer.  These commands are assumed to
be valid and taken more seriously during error handling.  Cache flush
is used by regular IO path and necessary for data integrity.  Mark it
with ATA_QCFLAG_IO.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-30 09:59:42 -04:00
Kristen Carlson Accardi ca77329fb7 [libata] Link power management infrastructure
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".

Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized.  Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.

Documentation/scsi/link_power_management_policy.txt has additional
information.

Signed-off-by:  Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-29 11:00:35 -04:00
Tejun Heo 4dbfa39b6c libata: relocate and fix post-command processing
Some commands need post-processing after successful completion.  This
was done in ata_scsi_qc_complete() till now but this has the following
problems.

* Post-command processing gets executed when qc is completed from EH.
  Some qc's are retried from EH with zero err_mask and thus triggers
  unnecessary/incorrect post-command processing.

* Command post processing doesn't belong to SAT layer.

* Link-wide revalidation was scheduled where device revalidation
  suffices.

This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used.  While at it,
restructure code a bit for readability.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-29 06:15:25 -04:00
Jeff Garzik 2dcb407e61 [libata] checkpatch-inspired cleanups
Tackle the relatively sane complaints of checkpatch --file.

The vast majority is indentation and whitespace changes, the rest are

* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-23 20:59:42 -04:00
Jens Axboe 45711f1af6 [SG] Update drivers to use sg helpers
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-22 21:19:53 +02:00
Linus Torvalds 92d15c2ccb Merge branch 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block: (63 commits)
  Fix memory leak in dm-crypt
  SPARC64: sg chaining support
  SPARC: sg chaining support
  PPC: sg chaining support
  PS3: sg chaining support
  IA64: sg chaining support
  x86-64: enable sg chaining
  x86-64: update pci-gart iommu to sg helpers
  x86-64: update nommu to sg helpers
  x86-64: update calgary iommu to sg helpers
  swiotlb: sg chaining support
  i386: enable sg chaining
  i386 dma_map_sg: convert to using sg helpers
  mmc: need to zero sglist on init
  Panic in blk_rq_map_sg() from CCISS driver
  remove sglist_len
  remove blk_queue_max_phys_segments in libata
  revert sg segment size ifdefs
  Fixup u14-34f ENABLE_SG_CHAINING
  qla1280: enable use_sg_chaining option
  ...
2007-10-16 10:09:16 -07:00
FUJITA Tomonori 8889e3c129 remove blk_queue_max_phys_segments in libata
LIBATA_MAX_PRD is the maximum number of DMA scatter/gather elements
permitted by the HBA's DMA engine. It's properly set to
q->max_hw_segments via the sg_tablesize parameter.

libata shouldn't call blk_queue_max_phys_segments. Now LIBATA_MAX_PRD
is equal to SCSI_MAX_PHYS_SEGMENTS by default (both is 128), so
everything is fine. But if they are changed, some code (like the scsi
mid layer, sg chaining, etc) might not work properly.

(Addition from Jens) The basic issue is that the physical segment
setting is purely a driver issue. And since SCSI is managing the sglist,
libata has no business changing the setting. All libata should care
about is the hw segment setting.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-10-16 11:24:44 +02:00
Randy Dunlap c5d0e6a0d2 docbook: fix libata content
Fix libata docbook warnings.

Warning(linux-2.6.23-git8//drivers/ata/libata-scsi.c:3251): No description found for parameter 'dev'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-15 17:56:36 -07:00
Tejun Heo f58db80267 libata: fix revalidation issuing after configuration commands
After commands which can change device configuration, EH is scheduled
to revalidate and reconfigure the device.  Host link was incorrectly
used unconditionally when scheduling EH action.  This resulted in
bogus revalidation request and mismatched configuration between device
and driver.  Fix it.

This bug was reported by Igor Durdanovic.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Igor Durdanovic <idurdanovic@comcast.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-15 15:24:54 -04:00
Alan Cox 2db78dd302 libata_scsi: Fix ATAPI transfer lengths
Some controller variants snoop the ATAPI length value for Packet
transfers to do state machine and FIFO management. Thus we want to
set it properly, even for cases where it is otherwise meaningless.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:45 -04:00
Tejun Heo 7d77b24708 libata-pmp-prep: implement sata_async_notification()
AN serves multiple purposes.  For ATAPI, it's used for media change
notification.  For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.

To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:42 -04:00
Tejun Heo e31e8531d6 libata-pmp-prep: implement ATA_HORKAGE_SKIP_PM
Some pseudo devices fail PM commands unnecessarily aborting system
suspend.  Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM
commands for these devices.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:41 -04:00
Tejun Heo 31cc23b349 libata-pmp-prep: implement ops->qc_defer()
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently.  This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.

If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link.  If ATA_DEFER_PORT, until a qc completes
on any link.  The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.

ops->qc_defer() replaces fixed ata_scmd_need_defer().  For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented.  ahci and
sata_sil24 are converted to use ata_std_qc_defer().

ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.

IMHO, this shouldn't cause any noticeable performance issues as

* for most cases deferring occurs rarely (except for NCQ-aware
  cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
  completes which usually is a very long time cpu-wise.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:41 -04:00
Tejun Heo 854c73a2f1 libata: misc updates for AN
Update AN support in preparation of PMP support.

* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Jeff Garzik c78968bb0f [libata] SCSI: simulator version, not device version, belongs in VPD
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Jeff Garzik 24f7568666 [libata] SCSI: clean up R/W recovery mode page
Clear ARRE, we don't do auto-reallocation on reads, just on writes.

Also, hardcode the size of the array using RW_RECOVERY_MPAGE_LEN,
following the style of the surrounding code.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Jeff Garzik 00bd02027f [libata] SCSI: improve FORMAT UNIT; minor code cleanups
* SAT specifies that FORMAT UNIT should be translated into a series
  of READ and WRITE commands that zero the ATA device.  That is far too
  cumbersome to bother with.

  Since we don't actually format the device, the old behavior of
  always returning success was inaccurate.  Change FORMAT UNIT from
  returning success immediately (old behavior) to always returning
  an error (new behavior).

* Add some comments around SYNCHRONIZE CACHE

* Shuffle scsi command code around a bit, so that things are close
  to alphabetic order.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-12 14:55:40 -04:00
Jeff Garzik 4539414552 [libata] Slightly improved no-op REQUEST SENSE, SEND DIAGNOSTIC
A few pedantic apps care about missing or lame "mandatory" SCSI
commands, so

REQUEST SENSE -- as we autosense, R.S. just returns zeroes

SEND DIAGNOSTIC -- our default (no-op) self-test succeeds, all
		   other requests for testing fail.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Jeff Garzik ad355b4628 [libata] SCSI: support INQUIRY page 89h (ATA info page)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:40 -04:00
Boaz Harrosh 7120165cf3 libata-scsi: convert to use the data buffer accessors
simple search-and-replace of direct scsi_cmnd access to
  use the data buffer accessors.

Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:38 -04:00
Boaz Harrosh e10b8c3f5f libata-scsi: Remove !use_sg code paths
This is a minimal patch needed to remove use of !use_sg
     but it is not a complete clean up of the !use_sg paths.
     Libata-core still has the qc->flags & ATA_QCFLAG_SG
     and !qc->n_elem code paths. Perhaps an ata maintainer
     would have a go at it.

     - TODO: further cleanup of qc->flags & ATA_QCFLAG_SG
       and !qc->n_elem code paths in libata-core
     - TODO: Use scsi_dma_{map,unmap} where applicable.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:38 -04:00
Kristen Carlson Accardi 2f2949680a [libata] ahci: send event when AN received
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change.  This will be done via the scsi device.

Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:33 -04:00
Mark Lord baf4fdfaaf libata: add support for ATA_16 on ATAPI
Add support for issuing ATA_16 passthru commands to ATAPI devices
managed by libata.  It requires the previous CDB length fix patch.

A boot/module parameter, "atapi_passthru16=0" can be used to globally
disable this feature, if ever desired.

tj: restructured __ata_scsi_queuecmd() according to Jeff's suggestion.

Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo 41bda9c980 libata-link: update hotplug to handle PMP links
Update hotplug to handle PMP links.  When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L.  While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:32 -04:00
Tejun Heo f58229f806 libata-link: implement and use link/device iterators
Multiple links and different number of devices per link should be
considered to iterate over links and devices.  This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().

This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES.  All such
changes have been examined and nothing should be broken.

While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo 9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Jens Axboe 165125e1e4 [BLOCK] Get rid of request_queue_t typedef
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.

Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
2007-07-24 09:28:11 +02:00
Tejun Heo 1ae463171c libata: improve SCSI scan failure handling
SCSI scan may fail due to memory allocation failure even if EH is not
in progress.  Due to use of GFP_ATOMIC in SCSI scan path, allocation
failure isn't too rare especially while probing multiple devices at
once which is the case when a bunch of devices are connected to PMP.

This patch moves SCSI scan failure detetion logic from
ata_scsi_hotplug() to ata_scsi_scan_host() and implement synchronous
scan behavior.  The synchronous path sleeps briefly and repeats SCSI
scan if some devices aren't attached properly.  It contains robust
retry loop to minimize the chance of device misdetection during boot
and falls back to async retry if everything fails.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 08:26:25 -04:00
Alan Cox d26fc9551a libata: Support chips with 64K PRD quirk
Add ata_dumb_qc_prep and supporting logic so that a driver can just
specify it needs to be helped in this area. 64K entries are split
as with drivers/ide.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-09 12:17:35 -04:00
Tejun Heo e00f1ff3c8 libata: call ata_check_atapi_dma() with qc better prepared
In atapi_xlat(), prepare qc better before calling
ata_check_atapi_dma() such that ata_check_atapi_dma() can use info
from qc.  While at it, reformat weird looking if/else block in the
function.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-27 02:50:08 -04:00
Albert Lee 2c3d2a46f1 libata passthru: update cached device paramters
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata.  Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:12 -04:00
Albert Lee fa4453c4c9 libata passthru: always enforce correct DEV bit
Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:12 -04:00
Albert Lee 23cb1d718d libata passthru: map UDMA protocols
Map the ATA passthru UDMA protocols to ATA_PROT_DMA.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:11 -04:00
Albert Lee 1dce589c38 libata passthru: support PIO multi commands
support the pass through of PIO multi commands.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:11 -04:00
Albert Lee f93f1078d0 libata passthru: update protocol numbers
Update the ATA passthru protocol numbers according to the new spec.

Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-06-09 23:08:11 -04:00
Jeff Garzik 6c7b7d2b76 [libata] Fix decoding of 6-byte commands
The code for parsing 6-byte SCSI command LBAs
missed the top 5 bits (the MSB).

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-25 04:39:39 -04:00
Tejun Heo d9aca22cf4 libata: remove libata.spindown_compat
With STANDBYDOWN tracking added, libata.spindown_compat isn't
necessary anymore.  If userspace shutdown(8) issues STANDBYNOW, libata
warns.  If userspace shutdown(8) doesn't issue STANDBYNOW, libata does
the right thing.  Userspace can tell whether kernel supports spindown
by testing whether sysfs node manage_start_stop exists as before.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-17 20:57:38 -04:00
Tejun Heo 13b8d09f5d libata: track spindown status and skip spindown_compat if possible
Our assumption that most distros issue STANDBYNOW seems wrong.  The
upstream sysvinit and thus many distros including gentoo and opensuse
don't take any action for libata disks on spindown.  We can skip
compat handling for these distros so that they don't need to update
anything to take advantage of kernel-side shutdown.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:31 -04:00
Tejun Heo da071b42f7 libata: fix shutdown warning message printing
Unlocking ap->lock and ssleeping don't work because SCSI commands can
be issued from completion path without context.  Reimplement delayed
completion by allowing translation functions to override
qc->scsidone(), storing the original completion function to
scmd->scsi_done() and overriding qc->scsidone() with a function which
schedules delayed invocation of scmd->scsi_done().

This isn't pretty at all but all the ugly parts are thankfully
contained in the stop translation path where the compat feature is
implemented.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-16 01:18:31 -04:00
Tejun Heo 920a4b1038 libata: implement libata.spindown_compat
Now that libata uses sd->manage_start_stop, libata spins down disk on
shutdown.  In an attempt to compensate libata's previous shortcoming,
some distros sync and spin down disks attached via libata in their
shutdown(8).  Some disks spin back up just to spin down again on
STANDBYNOW1 if the command is issued when the disk is spun down, so
this double spinning down causes problem.

This patch implements module parameter libata.spindown_compat which,
when set to one (default value), prevents libata from spinning down
disks on shutdown thus avoiding double spinning down.  Note that
libata spins down disks for suspend to mem and disk, so with
libata.spindown_compat set to one, disks should be properly spun down
in all cases without modifying shutdown(8).

shutdown(8) should be fixed eventually.  Some drive do spin up on
SYNCHRONZE_CACHE even when their cache is clean.  Those disks
currently spin up briefly when sd tries to shutdown the device and
then the machine powers off immediately, which can't be good for the
head.  We can't skip SYNCHRONIZE_CACHE during shudown as it can be
dangerous data integrity-wise.

So, this spindown_compat parameter is already scheduled for removal by
the end of the next year and here's what shutdown(8) should do.

  * Check whether /sys/modules/libata/parameters/spindown_compat
    exists.  If it does, write 0 to it.

  * For each libata harddisk {
	* Check whether /sys/class/scsi_disk/h:c:i:l/manage_start_stop
	  exists.  Iff it doesn't, synchronize cache and spin the disk
	  down as before.
  }

The above procedure will make shutdown(8) work properly with kernels
before this change, ones with this workaround and later ones without
it.

To accelerate shutdown(8) updates, if the compat mode is in use, this
patch prints BIG FAT warning for five seconds during shutdown (the
optimal interval to annoy the user just the right amount discovered by
hours of tireless usability testing).

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:01:04 -04:00
Tejun Heo 9666f4009c libata: reimplement suspend/resume support using sdev->manage_start_stop
Reimplement suspend/resume support using sdev->manage_start_stop.

* Device suspend/resume is now SCSI layer's responsibility and the
  code is simplified a lot.

* DPM is dropped.  This also simplifies code a lot.  Suspend/resume
  status is port-wide now.

* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.

* Resume now has to wait for disk to spin up before proceeding.  I
  couldn't find easy way out as libata is in EH waiting for the
  disk to be ready and sd is waiting for EH to complete to issue
  START_STOP.

* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
  This fixes spindown on shutdown and suspend-to-disk.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:01:03 -04:00
Tejun Heo f31871951b libata: separate out ata_host_alloc() and ata_host_register()
Reorganize ata_host_alloc() and its subroutines into the following
three functions.

* ata_host_alloc() : allocates host and its ports.  shost is not
  registered automatically.

* ata_scsi_add_hosts() : allocates and adds shosts associated with an
  ATA host.  Used by ata_host_register().

* ata_host_register() : takes a fully initialized ata_host structure
  and registers it to libata layer and probes it.

Only ata_host_alloc() and ata_host_register() are exported.
ata_device_add() is rewritten using the above functions.  This patch
does not introduce any observable behavior change.  Things worth
mentioning.

* print_id is assigned at registration time and LLDs are allowed to
  overallocate ports and reduce host->n_ports during initialization.
  ata_host_register() will throw away unused ports automatically.

* All SCSI host initialization stuff now resides in
  ata_scsi_add_hosts() in libata-scsi.c, where it should be.

* ipr is now the only user of ata_host_init().  Either kill it by
  converting ipr to use ata_host_alloc() and friends or rename and
  move it to libata-scsi.c

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:03 -04:00
Mark Lord 5a5dbd18a7 libata: add support for READ/WRITE LONG
The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.

The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.

The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.

This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:16:01 -04:00
Mark Lord f0ef88ed41 RESEND: libata: check cdb len per dev instead of per host
Resending, with s/printk/DPRINTK/ as pointed out by Alan.

Fix libata to perform CDB len validation per device
rather than per host.  This way, validation still works
when we have a mix of 12-byte and 16-byte devices on
a common host interface.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-28 14:15:55 -04:00
Mark Lord 277239f228 libata bugfix: preserve LBA bit for HDIO_DRIVE_TASK
Preserve the LBA bit in the DevSel/Head register for HDIO_DRIVE_TASK.

Signed-off-by:  Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-04 02:07:28 -04:00
Tejun Heo 6ffa01d88c libata: add CONFIG_PM to libata core layer
Conditionalize all PM related stuff in libata core layer using
CONFIG_PM.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-02 18:30:35 -05:00
Tejun Heo 44877b4e22 libata: s/ap->id/ap->print_id/g
ata_port has two different id fields - id and port_no.  id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number.  The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.

The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot.  This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.

Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:20 -05:00
Tejun Heo c3c70c443c libata: fix ata_scsi_change_queue_depth()
Fix ata_scsi_change_queue_depth() such that...

* NCQ on/off is exactly determined using the same logic as the issue path.

* queue depth is adjusted to 1 if NCQ is not enabled.

* -EINVAL is returned if requested action is ignored due to limitations.

This fixes the bug which allows queue depth to be increased on
blacklisted NCQ hosts/devices.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:19 -05:00
Tejun Heo fcf1bf1584 libata: fix ata_scmd_need_defer()
Fix ata_scmd_need_defer() such that...

* whether NCQ is used or not is exactly determined using the same
  criteria as the issue path.

* defer-check is performed in all cases.

This fixes race condition where turning off NCQ on the fly causes
non-NCQ commands sneak into NCQ phase.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:18 -05:00
Tejun Heo 4d05447ec7 libata: fix probe_ent alloc/free bugs
ata_probe_ent_alloc() had a temporary hack such that devm_kzalloc()
was used for allocation if devres had been previously initialized on
the device; otherwise, plain kzalloc() was used.  This was to make the
code useable from both the old and devres-aware libata drivers during
transition.  This hack made ata_sas_port_alloc() unable to determine
how the probe_ent is allocated, causing double free in some cases.

Remove the now-unneeded hack and make ata_sas_port_alloc() use
devm_kfree().

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:17 -05:00
Mark Lord 2b06719153 libata bugfix: HDIO_DRIVE_TASK
I was trying to use HDIO_DRIVE_TASK for something today,
and discovered that the libata implementation does not copy
over the upper four LBA bits from args[6].

This is serious, as any tools using this ioctl would have their
commands applied to the wrong sectors on the drive, possibly resulting
in disk corruption.

Ideally, newer apps should use SG_IO/ATA_16 directly,
avoiding this bug.  But with libata poised to displace drivers/ide,
better compatibility here is a must.

This patch fixes libata to use the upper four LBA bits passed
in from the ioctl.

The original drivers/ide implementation copies over all bits
except for the master/slave select bit.  With this patch,
libata will copy only the four high-order LBA bits,
just in case there are assumptions elsewhere in libata (?).

Signed-Off-By:  Mark Lord <mlord@pobox.com>

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-21 04:58:17 -05:00
Tejun Heo f0d36efdc6 libata: update libata core layer to use devres
Update libata core layer to use devres.

* ata_device_add() acquires all resources in managed mode.

* ata_host is allocated as devres associated with ata_host_release.

* Port attached status is handled as devres associated with
  ata_host_attach_release().

* Initialization failure and host removal is handedl by releasing
  devres group.

* Except for ata_scsi_release() removal, LLD interface remains the
  same.  Some functions use hacky is_managed test to support both
  managed and unmanaged devices.  These will go away once all LLDs are
  updated to use devres.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:37 -05:00
Tejun Heo 5924b74c1c libata: implement HDIO_GET_IDENTITY
'hdparm -I' doesn't work with ATAPI devices and sg_sat is not widely
spread yet leaving no easy way to access ATAPI IDENTIFY data.
Implement HDIO_GET_IDENTITY such that at least 'hdparm -i' works.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:34 -05:00
Tejun Heo 726f0785b6 libata: kill qc->nsect and cursect
libata used two separate sets of variables to record request size and
current offset for ATA and ATAPI.  This is confusing and fragile.
This patch replaces qc->nsect/cursect with qc->nbytes/curbytes and
kills them.  Also, ata_pio_sector() is updated to use bytes for
qc->cursg_ofs instead of sectors.  The field used to be used in bytes
for ATAPI and in sectors for ATA.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:31 -05:00
Tejun Heo a0cf733b33 libata: straighten out ATA_ID_* constants
* Kill _OFS suffixes in ATA_ID_{SERNO|FW_REV|PROD}_OFS for consistency
  with other ATA_ID_* constants.

* Kill ATA_SERNO_LEN

* Add and use ATA_ID_SERNO_LEN, ATA_ID_FW_REV_LEN and ATA_ID_PROD_LEN.
  This change also makes ata_device_blacklisted() use proper length
  for fwrev.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:30 -05:00
Adrian Bunk 7102d230d6 drivers/ata/: make 4 functions static
This patch makes the following needlessly global functions static:
- libata-core.c: ata_qc_complete_internal()
- libata-scsi.c: ata_scsi_qc_new()
- libata-scsi.c: ata_dump_status()
- libata-scsi.c: ata_to_sense_error()

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:30 -05:00
Arjan van de Ven 7a44e910f4 [PATCH] user of the jiffies rounding patch: ATA subsystem
This patch introduces users of the round_jiffies() function: ATA subsystem

This delayed work is of the "about once a second" variety and can be rounded
to coincide with other wakers.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-09 17:39:29 -05:00
Robert Hancock 78981a7c6c libata: fix translation for START STOP UNIT
libata's SCSI translation for the SCSI START STOP UNIT command with the
START bit clear (i.e.  stopping the drive) appears to be incorrect.  It
sends an ATA STANDBY command with the time period set to 0, which the code
comment says means "now", but the ATA standard says this means disable the
standby timer, which effectively does nothing.  Change this to issue a
STANDBY IMMEDIATE command which will actually spin the drive down.  The SAT
(SCSI/ATA Translation) standard revision 9 concurs with this choice.

Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:20:39 -05:00
David Milburn af068bd1de libata-scsi: ata_task_ioctl should return ATA registers from sense data
User applications using the HDIO_DRIVE_TASK ioctl through libata expect
specific ATA registers to be returned to userspace.  Verified that
ata_task_ioctl correctly returns register values to the smartctl
application.

Signed-off-by: David Milburn <dmilburn@redhat.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-30 09:20:39 -05:00
Brian King 7a801184fa libata: Fixup n_elem initialization
Fixup the inialization of qc->n_elem. It currently gets
initialized to 1 for commands that do not transfer any data.
Fix this by initializing n_elem to 0 and only setting to 1
in ata_scsi_qc_new when there is data to transfer. This fixes
some problems seen with SATA devices attached to ipr adapters.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-01-24 02:04:34 -05:00
Tejun Heo 2e5704f63e [PATCH] libata: take scmd->cmd_len into account when translating SCSI commands
libata depended on SCSI command to have the correct length when
tranlating it into an ATA command.  This generally worked for commands
issued by SCSI HLD but user could issue arbitrary broken command using
sg interface.

Also, when building ATAPI command, full command size was always
copied.  Because some ATAPI devices needs bytes after CDB cleared, if
upper layer doesn't clear bytes after CDB, such devices will
malfunction.  This necessiated recent clear-garbage-after-CDB fix in
sg interfaces.  However, scsi_execute() isn't fixed yet and HL-DT-ST
DVD-RAM GSA-H30N malfunctions on initialization commands issued from
SCSI.

This patch makes xlat functions always consider SCSI cmd_len.  Each
translation function checks for proper cmd_len and ATAPI translaation
clears bytes after CDB.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-20 14:26:26 -05:00
Tejun Heo ad706991f4 [PATCH] libata: kill @cdb argument from xlat methods
xlat function will be updated to consider qc->scsicmd->cmd_len and
many xlat functions deference qc->scsicmd already.  It doesn't make
sense to pass qc->scsicmd->cmnd as @cdb separately.  Kill the
argument.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-20 14:26:26 -05:00
Tejun Heo 542b1444c5 [PATCH] libata: clean up variable name usage in xlat related functions
Variable names in xlat functions are quite confusing now.  'scsicmd'
is used for CDB while qc->scsicmd points to struct scsi_cmnd while
'cmd' is used for struct scsi_cmnd.

This patch cleans up variable names in xlat functions such that 'scmd'
is used for struct scsi_cmnd and 'cdb' for CDB.  Also, 'scmd' local
variable is added if qc->scsicmd is used multiple times.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-20 14:26:26 -05:00
Jeff Garzik da02d2a16e [libata] use kmap_atomic(KM_IRQ0) in SCSI simulator
We are inside spin_lock_irqsave().  quoth akpm's debug facility:

 [  231.948000] SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
 [  232.232000] ata1.00: configured for UDMA/33
 [  232.404000] WARNING (1) at arch/i386/mm/highmem.c:47 kmap_atomic()
 [  232.404000]  [<c01162e6>] kmap_atomic+0xa9/0x1ab
 [  232.404000]  [<c0242c81>] ata_scsi_rbuf_get+0x1c/0x30
 [  232.404000]  [<c0242caf>] ata_scsi_rbuf_fill+0x1a/0x87
 [  232.404000]  [<c0243ab2>] ata_scsiop_mode_sense+0x0/0x309
 [  232.404000]  [<c01729d5>] end_bio_bh_io_sync+0x0/0x37
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c02311c6>] scsi_done+0x0/0x16
 [  232.404000]  [<c0242dcc>] ata_scsi_simulate+0xb0/0x13f
[...]

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-16 10:12:36 -05:00
David Howells 9db7372445 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/ata/libata-scsi.c
	include/linux/libata.h

Futher merge of Linus's head and compilation fixups.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 17:01:28 +00:00
David Howells 4c1ac1b491 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:

	drivers/infiniband/core/iwcm.c
	drivers/net/chelsio/cxgb2.c
	drivers/net/wireless/bcm43xx/bcm43xx_main.c
	drivers/net/wireless/prism54/islpci_eth.c
	drivers/usb/core/hub.h
	drivers/usb/input/hid-core.c
	net/core/netpoll.c

Fix up merge failures with Linus's head and fix new compilation failures.

Signed-Off-By: David Howells <dhowells@redhat.com>
2006-12-05 14:37:56 +00:00
Tejun Heo bd056d7eeb [PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
Separate out rw ATA taskfile building from ata_scsi_rw_xlat() into
ata_build_rw_tf().  This will be used to improve media error handling.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-12-03 17:56:24 +09:00
Tejun Heo f84e7e41e1 [PATCH] libata: make sure sdev doesn't go away while rescanning
ata_scsi_dev_rescan() doesn't synchronize against SCSI device detach
and the target sdev might go away in the middle.  Fix it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2006-12-03 17:56:24 +09:00
Tejun Heo 6a36261e63 [PATCH] libata: fix READ CAPACITY simulation
* READ CAPACITY (16) implementation fixed.  Result was shifted by two
  bytes.  Carlos Pardo spotted this problem and submitted preliminary
  patch.  Capacity => 2TB is handled correctly now.  (verifid w/ fake
  capacity)

* Use dev->n_sectors instead of re-reading directly from ID data.

* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
  This should be done for all simulation functions.  Userland can
  issue any simulated command with arbitrary buffer length.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
2006-12-03 17:56:23 +09:00
Tejun Heo d25614bad6 [PATCH] libata: improve SCSI sense data generation
Update ata_gen_ata_sense() to use desc format sense data to report the
first failed block.  The first failed block is read from result_tf
using ata_tf_read_block() which can handle all three address formats.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:46:00 -05:00
Tejun Heo 750426aa1a [PATCH] libata: cosmetic changes to sense generation functions
* s/ata_gen_ata_desc_sense/ata_gen_passthru_sense/

* s/ata_gen_fixed_sense/ata_gen_ata_sense/

* make both functions static

* neither function has locking requirement, change it to None.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:46:00 -05:00
Tejun Heo f38621b310 [PATCH] libata: fix passthru sense data header
sb[7] should contain the length of whole information sense data
descriptor while desc[1] should contain the number of following bytes
in the descriptor.  ie. 14 for sb[7] but 12 for desc[1].

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:46:00 -05:00
Tejun Heo 6fc49adb94 [PATCH] libata: use FLUSH_EXT only when driver is larger than LBA28 limit
Many drives support LBA48 even when its capacity is smaller than
1<<28, as LBA48 is required for many functionalities.  FLUSH_EXT is
mandatory for drives w/ LBA48 support.

Interestingly, at least one of such drives (ST960812A) has problems
dealing with FLUSH_EXT.  It eventually completes the command but takes
around 7 seconds to finish in many cases thus drastically slowing down
IO transactions.  This seems to be a firmware bug which sneaked into
production probably because no other ATA driver including linux IDE
issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT
but is smaller than 1<<28 blocks.

This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive
supports LBA48 & FLUSH_EXT and is larger than LBA28 limit.  Both cache
flush paths are updated to issue FLUSH_EXT only when the flag is set.
Note that the changed behavior is more inline with the rest of libata.
libata prefers shorter commands whenever possible.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Danny Kukawka <dkukawka@novell.com>
Cc: Stefan Seyfried <seife@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:45:54 -05:00
Tejun Heo 914ed354b3 [PATCH] libata: move dev->max_sectors configuration into ata_dev_configure()
Move dev->max_sectors configuration from ata_scsi_dev_config() to
ata_dev_configure().

* more consistent.
* allows LLDs to peek at the default dev->max_sectors value.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:41:31 -05:00
Tejun Heo 309afcb5c8 [PATCH] libata: make user scan wait for scan to complete
Make user scan wait for scan to complete.  This way user can wait for
warm plug request to complete and is prevented from causing EH event
storm by repetitively issuing scan request while EH is in progress.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Fajun Chen <fajunchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-12-01 22:40:29 -05:00
Brian King 08475a1920 [PATCH] libata: Fixup ata_sas_queuecmd to handle __ata_scsi_queuecmd failure
Fixes ata_sas_queuecmd to properly handle a failure from
__ata_scsi_queuecmd.

Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-28 03:51:55 -05:00
Tejun Heo c31f571d9f [PATCH] libata: don't schedule EH on wcache on/off if old EH
Do not schedule EH for revalidation on wcache on/off if old EH.  Old
EH cannot handle it and will result in WARN_ON()'s and oops.

This closes bug #7412.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2006-11-28 03:45:13 -05:00
David Howells 65f27f3844 WorkStruct: Pass the work_struct pointer instead of context data
Pass the work_struct pointer to the work function rather than context data.
The work function can use container_of() to work out the data.

For the cases where the container of the work_struct may go away the moment the
pending bit is cleared, it is made possible to defer the release of the
structure by deferring the clearing of the pending bit.

To make this work, an extra flag is introduced into the management side of the
work_struct.  This governs auto-release of the structure upon execution.

Ordinarily, the work queue executor would release the work_struct for further
scheduling or deallocation by clearing the pending bit prior to jumping to the
work function.  This means that, unless the driver makes some guarantee itself
that the work_struct won't go away, the work function may not access anything
else in the work_struct or its container lest they be deallocated..  This is a
problem if the auxiliary data is taken away (as done by the last patch).

However, if the pending bit is *not* cleared before jumping to the work
function, then the work function *may* access the work_struct and its container
with no problems.  But then the work function must itself release the
work_struct by calling work_release().

In most cases, automatic release is fine, so this is the default.  Special
initiators exist for the non-auto-release case (ending in _NAR).


Signed-Off-By: David Howells <dhowells@redhat.com>
2006-11-22 14:55:48 +00:00