Commit Graph

5 Commits

Author SHA1 Message Date
Pavel Machek 697894b9b8 mfd: ti-lmu: Use of_device_get_match_data() helper
Replace of_match_device() with of_device_get_match_data(), which
slightly decreases lines of code and allows to move the DT table
next to the I2C table.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-10-23 08:58:34 +01:00
Pavel Machek 7891d37509 mfd: ti-lmu: Use managed resource for everything
This replaces all remaining unmanaged resources with device
managed ones, so that the remove function is no longer needed.
This makes the code slightly shorter and fixes two problems:

 1. The hardware is disabled after the child devices have
    been removed. Previously there was a potential race
    condition.
 2. The hardware is disabled when mfd_add_devices fails
    during probe.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-10-23 08:58:34 +01:00
Pavel Machek 7a6a395b16 mfd: ti-lmu: Switch to GPIOD
Use new descriptor based API instead of the legacy one.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-10-23 08:58:34 +01:00
Sebastian Reichel 5b6850fa90 mfd: ti-lmu: constify mfd_cell tables
Add const attribute to all mfd_cell structures.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2018-10-23 08:58:34 +01:00
Milo Kim d5aa11bfe9 mfd: Add TI LMU driver
TI LMU (Lighting Management Unit) driver supports lighting devices below.

  LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.

LMU devices have common features.
  - I2C interface for accessing device registers
  - Hardware enable pin control
  - Backlight brightness control
  - Notifier for hardware fault monitoring
  - Regulators for LCD display bias

It contains fault monitor, backlight, LED and regulator driver.

LMU fault monitor
-----------------
  LM3633 and LM3697 provide hardware monitoring feature.
  It enables open or short circuit detection.
  After monitoring is done, each device should be re-initialized.
  Notifier is used for this case.
  Separate patch for 'ti-lmu-fault-monitor' will be sent later.

Backlight
---------
  It's handled by TI LMU backlight consolidated driver and
  chip dependent data. Separate patchset will be sent later.

LED indicator
-------------
  LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
  supported. Separate patch for 'leds-lm3633' will be sent later.

Regulator
---------
  LM3631 has 5 regulators for the display bias.
  LM3632 supports 3 regulators. One consolidated driver enables it.
  The lm363x regulator driver is already upstreamed.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2017-04-27 09:25:04 +01:00