Commit Graph

357 Commits

Author SHA1 Message Date
Michael Chan a0ba676008 bnx2: Use netif_carrier_off() to prevent timeout.
Based on original patch from Stanislaw Gruszka <sgruszka@redhat.com>.

Using netif_carrier_off() is better than updating all the ->trans_start
on all the tx queues.

netif_carrier_off() needs to be called after bnx2_disable_int_sync()
to guarantee no race conditions with the serdes timers that can
modify the carrier state.

If the chip or phy is reset, carrier will turn back on when we get the
link interrupt.  If there is no reset, we need to turn carrier back on
in bnx2_netif_start().  Again, the phy_lock prevents race conditions with
the serdes timers.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17 17:34:43 -07:00
Michael Chan a931d29404 bnx2: Update 5709 MIPS firmware and version to 2.0.15.
New firmware fixes a performance regression on small packets.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17 17:33:31 -07:00
Eddie Wai b98eba5278 bnx2: Fix register printouts during NETEV_WATCHDOG.
Dump the correct MCP registers and add EMAC_RX_STATUS register during
NETDEV_WATCHDOG for debugging.

Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-17 17:32:56 -07:00
Michael Chan a33fa66bcf bnx2: Add prefetches to rx path.
Add prefetches of the skb and the next rx descriptor to speed up rx path.

Use prefetchw() for the skb [suggested by Eric Dumazet].

The rx descriptor is in skb->data which is mapped for streaming mode DMA.
Eric Dumazet pointed out that we should not prefetch the data before
dma_sync.  So we prefetch only if dma_sync is no_op on the system.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 22:17:24 -07:00
Michael Chan c67938a9e0 bnx2: Add GRO support.
And turn on NETIF_F_GRO by default [requested by DaveM].

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06 22:17:23 -07:00
David S. Miller 7ef527377b Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2010-05-02 22:02:06 -07:00
Michael Chan 587611d6e4 bnx2: Update version to 2.0.9.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-27 14:38:16 -07:00
Michael Chan 212f9934af bnx2: Prevent "scheduling while atomic" warning with cnic, bonding and vlan.
The bonding driver calls ndo_vlan_rx_register() while holding bond->lock.
The bnx2 driver calls bnx2_netif_stop() to stop the rx handling while
changing the vlgrp.  The call also stops the cnic driver which sleeps
while the bond->lock is held and cause the warning.

This code path only needs to stop the NAPI rx handling while we are
changing the vlgrp.  Since no reset is going to occur, there is no need
to stop cnic in this case.  By adding a parameter to bnx2_netif_stop()
to skip stopping cnic, we can avoid the warning.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-27 14:38:16 -07:00
Michael Chan c441b8d2cb bnx2: Fix lost MSI-X problem on 5709 NICs.
It has been reported that under certain heavy traffic conditions in MSI-X
mode, the driver can lose an MSI-X vector causing all packets in the
associated rx/tx ring pair to be dropped.  The problem is caused by
the chip dropping the write to unmask the MSI-X vector by the kernel
(when migrating the IRQ for example).

This can be prevented by increasing the GRC timeout value for these
register read and write operations.

Thanks to Dell for helping us debug this problem.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-27 14:38:15 -07:00
FUJITA Tomonori 1a4ccc2d46 bnx2: use the dma state API instead of the pci equivalents
The DMA API is preferred.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-07 21:05:35 -07:00
David S. Miller 4a35ecf8bf Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/bonding/bond_main.c
	drivers/net/via-velocity.c
	drivers/net/wireless/iwlwifi/iwl-agn.c
2010-04-06 23:53:30 -07:00
Jiri Pirko 22bedad3ce net: convert multicast list to list_head
Converts the list and the core manipulating with it to be the same as uc_list.

+uses two functions for adding/removing mc address (normal and "global"
 variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
 manipulation with lists on a sandbox (used in bonding and 80211 drivers)

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-03 14:22:15 -07:00
Michael Chan 1bf1e347ef bnx2: Use proper handler during netpoll.
Netpoll needs to call the proper handler depending on the IRQ mode
and the vector.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-23 23:19:56 -07:00
Benjamin Li 4327ba435a bnx2: Fix netpoll crash.
The bnx2 driver calls netif_napi_add() for all the NAPI structs during
->probe() time but not all of them will be used if we're not in MSI-X
mode.  This creates a problem for netpoll since it will poll all the
NAPI structs in the dev_list whether or not they are scheduled, resulting
in a crash when we access structure fields not initialized for that vector.

We fix it by moving the netif_napi_add() call to ->open() after the number
of IRQ vectors has been determined.

Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-23 23:19:55 -07:00
Matt Carlson df25bc38b5 bnx2: Remove now useless VPD code
Now that the VPD searching code is abstracted away, the outer loop used
to detect the read-only large resource data type section is useless.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:33 -08:00
Matt Carlson 4067a8541d pci: Add helper to search for VPD keywords
This patch adds the pci_vpd_find_info_keyword() helper function to
find information field keywords within read-only and read-write large
resource data type sections.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:33 -08:00
Matt Carlson e1d5bdabb9 pci: Add VPD information field helper functions
This patch adds a preprocessor constant to describe the PCI VPD
information field header size and an inline function to extract the
size of the information field itself.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:32 -08:00
Matt Carlson b55ac1b226 pci: Add helper to find a VPD resource data type
This patch adds the pci_vpd_find_tag() helper function to find VPD
resource data types in a buffer.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:32 -08:00
Matt Carlson 7ad506fa1a pci: Add large and small resource data type code
This patch introduces more VPD preprocessor definitions to identify some
small and large resource data type item names.  The patch then continues
to correct how the tg3 and bnx2 drivers search for the "read-only data"
large resource data type.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:31 -08:00
Matt Carlson a2ce766238 pci: Add PCI LRDT tag size and section size
This patch adds a preprocessor constant to describe the PCI VPD large
resource data type tag size and an inline function to extract the large
resource section size from the large resource data type tag.

Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-28 00:43:30 -08:00
Jiri Pirko 0ddf477b8a net: convert multiple drivers to use netdev_for_each_mc_addr, part3
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-22 15:45:51 -08:00
Joe Perches 3a9c6a4915 drivers/net/bnx2.c: Use (pr|netdev|netif)_<level> macro helpers
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Remove #define PFX
Use pr_<level>
Use netdev_<level>
Use netif_<level>
Remove periods from formats
Coalesce long formats
Coalesce some printks

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-17 17:45:19 -08:00
Michael Chan bec92044b7 bnx2: Update firmwares and update version to 2.0.8.
- Increase FTQ depth to 256 to ehnabce performance.
- Fix RV2P context corruption on 5709 when flow control is enabled.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:42 -08:00
Patrick Rabau c9885fe5a7 bnx2: Fix bug when saving statistics.
This fixes the problem of dropping the carry when adding 2 32-bit values.
Switch to use array indexing for better readability.

Reported by and fix provided by Patrick Rabau.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:04 -08:00
Michael Chan beb499afe3 bnx2: Allow user-specified multiple advertisement speed values.
Remove unnecessary code that works around older versions of ethtool
that can pass down invalid advertisement speed values.  This old
code prevents the user from specifying multiple advertisement values.
The new code uses simple masking to mask out invalid advertisment bits.

Reported-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:04 -08:00
Michael Chan 5726026bff bnx2: Adjust flow control water marks.
The current water marks are too high and can cause unnecessary flow
control frames.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:03 -08:00
Michael Chan e9f26c49ce bnx2: Need to call cnic_setup_cnic_irq_info() after MTU change.
New status blocks are allocated during MTU change so we need to
update this information for the cnic driver.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:02 -08:00
Michael Chan efde73a35c bnx2: Check BNX2_FLAG_USING_MSIX flag when setting up MSIX.
Checking the flag is more correct than checking bp->irq_nvecs. By
accident it is not a problem because we always have more than 1
vectors when using MSIX mode.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-16 15:19:02 -08:00
Jiri Pirko 4cd24eaf0c net: use netdev_mc_count and netdev_mc_empty when appropriate
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.

Jirka

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-02-12 11:38:58 -08:00
Alexey Dobriyan 257ddbdad1 netdev: remove HAVE_ leftovers
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-28 06:01:35 -08:00
Jiri Pirko 32e7bfc411 net: use helpers to access uc list V2
This patch introduces three macros to work with uc list from net drivers.

Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-25 13:36:10 -08:00
Michael Chan 354fcd7774 bnx2: Save statistics during reset.
MTU changes, ring size changes, etc cause the chip to be reset and the
statisctics flushed.  To keep track of the accumulated statistics, we
add code to save the whole statistics block before reset.  We also
modify the macros and statistics functions to return the sum of the
saved and current counters.

Based on original patch by Breno Leitao <leitao@linux.vnet.ibm.com>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17 19:16:03 -08:00
Michael Chan a47430583d bnx2: Refine statistics code.
Refine the statistics macros by passing in just the name of the
counter field.  This makes it a lot easier and cleaner to add
counters saved before the last reset in the next patch.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-17 19:16:02 -08:00
Benjamin Li e2eb8e3859 bnx2: Flush the register writes which setup the MSI-X table
The MSI-X table size needs to be properly set before pci_enable_msix()
is called.  But on certain machines, the writes are delayed and the
MSI-X table size is incorrectly read.  By reading the
BNX2_PCI_MSIX_CONTROL register, the writes are flushed and now
ensure that the MSI-X table is set correctly before MSI-X
is enable on the device.

This patch was originally diagnosed and authored by
Kalyan Ram Chintalapati <kalyanc@vmware.com>.

Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Kalyan Ram Chintalapati <kalyanc@vmware.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08 00:51:21 -08:00
Michael Chan b746656069 bnx2: Fix bnx2_netif_stop() merge error.
The error was introduced while merging:

commit 4529819c45
bnx2: reset_task is crashing the kernel. Fixing it.

Signed-off-by: Michael Chan <mchan@broadcom.com>k
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-20 18:40:18 -08:00
Breno Leitao e6bf95ffa8 bnx2: fixing a timout error due not refreshing TX timers correctly
When running the following script on an active bnx2 interface:

while(true); do ifconfig ethX mtu 9000; ifconfig ethX mtu 1500; done

A timeout error appears and dumps the following stack:

NETDEV WATCHDOG: eth4 (bnx2): transmit queue 0 timed out
------------[ cut here ]------------
Badness at net/sched/sch_generic.c:261
<snip>

This patch just fixes the way that ->trans_start is refreshed.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-18 20:35:34 -08:00
Breno Leitao 4529819c45 bnx2: reset_task is crashing the kernel. Fixing it.
If bnx2 schedules a reset via the reset_task, e.g., due to a TX
timeout, it's possible for the NIC to be disabled with packets
pending for transmit.  In this case, napi_disable will loop forever,
eventually crashing the kernel.  This patch moves the disable of
the device to after the napi_disable call.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-18 20:29:04 -08:00
Michael Chan 012093f6d5 bnx2: Refine VPD logic.
- Replace magic values with constants
- Simplify length calculation and fix a bug

Based on valuable feedback from Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 15:58:00 -08:00
Michael Chan 55dbabee63 bnx2: Update version to 2.0.3.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:14 -08:00
Michael Chan 76d9906170 bnx2: Read firmware version from VPD.
And display it through ethtool -i.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:13 -08:00
Michael Chan b929e53cb7 bnx2: Print warning when unable to allocate the full SKB/page ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:11 -08:00
Michael Chan 20175c57f2 bnx2: Dump some state during tx timeout.
To help debug the problem.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:11 -08:00
Michael Chan 51bf6bb424 bnx2: Protect tx timeout reset with rtnl_lock().
To prevent race conditions with other reset events.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-03 13:18:09 -08:00
David S. Miller e00484023e Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 2009-12-02 22:00:34 -08:00
Alexander Duyck e95524a726 bnx2: remove skb_dma_map/unmap calls from driver
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.

[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
  code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02 19:57:13 -08:00
Breno Leitao 529fab67d7 bnx2: EEH is failing with timeout
bnx2 is failing when a PCI error is detected. The error is the
following:

bnx2: Chip not in correct endian mode
bnx2: fw sync timeout, reset code = 404001d

This error was caused because the way pci_restore_state() is working
after commit 4b77b0a2ba ("PCI: Clear
saved_state after the state has been restored").

Signed-off-by: Breno Leitao<leitao@linux.vnet.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-02 15:36:28 -08:00
Eric Dumazet c7079857cd bnx2: avoid compiler warnings
drivers/net/bnx2.c: In function ‘bnx2_enable_forced_2g5’:
drivers/net/bnx2.c:1447: warning: ‘bmcr’ may be used uninitialized in this function
drivers/net/bnx2.c: In function ‘bnx2_disable_forced_2g5’:
drivers/net/bnx2.c:1482: warning: ‘bmcr’ may be used uninitialized in this function

One fix would be to have an initial value, but a plain return might be better.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-04 05:06:26 -08:00
Ben Hutchings 7ab0f2736b netdev: Remove redundant checks for CAP_NET_ADMIN in MDIO implementations
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-03 20:02:11 -07:00
David S. Miller 6cdee2f96a Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
	drivers/net/yellowfin.c
2009-09-02 00:32:56 -07:00
Stephen Hemminger 61357325f3 netdev: convert bulk of drivers to netdev_tx_t
In a couple of cases collapse some extra code like:
   int retval = NETDEV_TX_OK;
   ...
   return retval;
into
   return NETDEV_TX_OK;

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01 01:14:07 -07:00