This reverts commit d2180e0cf7.
The commit was flawed in that if the device_node pointers are different,
then in fact a different device is present and the device node could be
different in ways other than full_name.
As Frank Rowand explained:
"When an overlay (1) is removed, all uses and references to the nodes and
properties in that overlay are no longer valid. Any driver that uses any
information from the overlay _must_ stop using any data from the overlay.
Any driver that is bound to a new node in the overlay _must_ unbind. Any
driver that became bound to a pre-existing node that was modified by the
overlay (became bound after the overlay was applied) _must_ adjust itself
to account for any changes to that node when the overlay is removed. One
way to do this is to unbind when notified that the overlay is about to
be removed, then to re-bind after the overlay is completely removed.
If an overlay (2) is subsequently applied, a node with the same
full_name as from overlay (1) may exist. There is no guarantee
that overlay (1) and overlay (2) are the same overlay, even if
that node has the same full_name in both cases."
Also, there's not sufficient overlay support in mainline to actually
remove and re-apply an overlay to hit this condition as overlays can
only be applied from in kernel APIs.
Fixes: d2180e0cf7 ("[media] v4l: async: make v4l2 coexist with devicetree nodes in a dt overlay")
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Javi Merino <javi.merino@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 flash interface allows controlling multiple LEDs through a single
sub-devices if, and only if, these LEDs are of different types. This
approach scales badly for flash controllers that drive multiple flash LEDs
or for LED specific associations. Essentially, the original assumption of a
LED driver chip that drives a single flash LED and an indicator LED is no
longer valid.
Address the matter by registering one sub-device per LED.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> (for greybus/light)
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These formats are compressed 12-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR12P
V4L2_PIX_FMT_SGBRG12P
V4L2_PIX_FMT_SGRBG12P
V4L2_PIX_FMT_SRGGB12P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change is intended to give to the v4l2 drivers a choice to
change the default behavior of the v4l2-core DMA mapping direction
from DMA_TO/FROM_DEVICE (depending on the buffer type CAPTURE or
OUTPUT) to DMA_BIDIRECTIONAL during queue_init time.
Initially the issue with DMA mapping direction has been found in
Venus encoder driver where the hardware (firmware side) adds few
lines padding on bottom of the image buffer, and the consequence
is triggering of IOMMU protection faults.
This will help supporting venus encoder (and probably other drivers
in the future) which wants to map output type of buffers as
read/write.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid using a generic name such as MAX_DATA_LANES in a header file widely
included in drivers. Instead, call it V4L2_FWNODE_CSI2_MAX_DATA_LANES.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The clock lane is the first lane in the lane_polarities array. Reflect this
consistently by putting the number of data lanes after the number of clock
lanes.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
fwnode_property_read_u32_array() only returns the number of array elements
if the array argument is NULL. The assumption that it always did so lead to
lane-polarities properties never being read.
Fixes: 4ee236219f ("media: v4l2-fwnode: suppress a warning at OF parsing logic")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_input32 struct wasn't updated when this field was added.
It didn't cause a failure in the compat code, but it is better to
keep it in sync with v4l2_input to avoid confusion.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Certain syscalls like recvmmsg support 64 bit timespec values for the
X32 ABI. The helper function compat_put_timespec converts a timespec
value to a 32 bit or 64 bit value depending on what ABI is used. The
v4l2 compat layer, however, is not designed to support 64 bit timespec
values and always uses 32 bit values. Hence, compat_put_timespec must
not be used.
Without this patch, user space will be provided with bad timestamp
values from the VIDIOC_DQEVENT ioctl. Also, fields of the struct
v4l2_event32 that come immediately after timestamp get overwritten,
namely the field named id.
Fixes: 81993e81a9 ("compat: Get rid of (get|put)_compat_time(val|spec)")
Cc: stable@vger.kernel.org
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Tiffany Lin <tiffany.lin@mediatek.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit b2787845fb ("V4L/DVB (5289): Add support for video output
overlays.") added the field global_alpha to struct v4l2_window but did
not update the compat layer accordingly. This change adds global_alpha
to struct v4l2_window32 and copies the value for global_alpha back and
forth.
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some debug output whose log level is set 1 flooded the log.
Their log level is lowered to find the important log easily.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
None of the flash operations are mandatory and therefore there should be
no need for the flash ops structure either. Accept NULL.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 flash class initialisation expects struct led_classdev_flash that
describes an indicator but only uses struct led_classdev which is a field
iled_cdev in the struct. Use struct iled_cdev only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_fwnode_endpoint_alloc_parse() is intended as a replacement for
v4l2_fwnode_endpoint_parse(). It parses the "link-frequency" property and
if the property isn't found, it returns an error. However,
"link-frequency" is an optional property and if it does not exist is not
an error. Instead, the number of link frequencies is simply zero in that
case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This function is used only internally. So, make it static.
Shuts up this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:153:6: warning: no previous prototype for 'v4l2_fwnode_endpoint_parse_csi1_bus' [-Wmissing-prototypes]
void v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
smatch produce this warning:
drivers/media/v4l2-core/v4l2-fwnode.c:76 v4l2_fwnode_endpoint_parse_csi_bus() error: buffer overflow 'array' 5 <= u16max
That's because, in thesis, the routine might have called with
some value at bus->num_data_lanes. That's not the current
case.
Yet, better to shut up this warning, and make the code more
reliable if some future changes might cause a bug.
While here, simplify the code a little bit by reading only
once from lanes-properties array.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
CCP2 and CSI-1, are older single data lane serial busses.
[mchehab@s-opensource.com: don't use spaces for identation]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Just obtain it. It'll actually get used soon with CSI-1/CCP2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The function to parse CSI2 bus parameters was called
v4l2_fwnode_endpoint_parse_csi_bus(), rename it as
v4l2_fwnode_endpoint_parse_csi2_bus() in anticipation of CSI1/CCP2
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
5238 112 4 5354 14ea drivers/media/v4l2-core/videobuf2-dma-sg.o
File size After adding 'const':
text data bss dec hex filename
5358 0 4 5362 14f2 drivers/media/v4l2-core/videobuf2-dma-sg.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3171 192 0 3363 d23 drivers/media/v4l2-core/videobuf2-vmalloc.o
File size After adding 'const':
text data bss dec hex filename
3291 80 0 3371 d2b drivers/media/v4l2-core/videobuf2-vmalloc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dma_buf_ops are not supposed to change at runtime. All functions
working with dma_buf_ops provided by <linux/dma-buf.h> work with
const dma_buf_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6035 272 0 6307 18a3 drivers/media/v4l2-core/videobuf2-dma-contig.o
File size After adding 'const':
text data bss dec hex filename
6155 160 0 6315 18ab drivers/media/v4l2-core/videobuf2-dma-contig.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit 680d87c0a9 ("[media] tuner-core: use pr_foo, instead of
internal printk macros") removed the use of PREFIX, remove the #define
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The type field in struct v4l2_selection is supposed to never use the
_MPLANE variants. E.g. if the driver supports V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE,
then userspace should still pass V4L2_BUF_TYPE_VIDEO_CAPTURE.
The reasons for this are lost in the mists of time, but it is really
annoying. In addition, the exynos drivers didn't follow this rule and
instead expected the _MPLANE type.
To fix that code is added to the v4l2 core that maps the _MPLANE buffer
types to their regular equivalents before calling the driver.
Effectively this allows for userspace to use either _MPLANE or the regular
buffer type. This keeps backwards compatibility while making things easier
for userspace.
Since drivers now never see the _MPLANE buffer types the exynos drivers
had to be adapted as well.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are multiple places where arrays or otherwise variable sized
buffer are allocated through V4L2 core code, including things like
controls, memory pages, staging buffers for ioctls and so on. Such
allocations can potentially require an order > 0 allocation from the
page allocator, which is not guaranteed to be fulfilled and is likely to
fail on a system with severe memory fragmentation (e.g. a system with
very long uptime).
Since the memory being allocated is intended to be used by the CPU
exclusively, we can consider using vmalloc() as a fallback and this is
exactly what the recently merged kvmalloc() helpers do. A kmalloc() call
is still attempted, even for order > 0 allocations, but it is done
with __GFP_NORETRY and __GFP_NOWARN, with expectation of failing if
requested memory is not available instantly. Only then the vmalloc()
fallback is used. This should give us fast and more reliable allocations
even on systems with higher memory pressure and/or more fragmentation,
while still retaining the same performance level on systems not
suffering from such conditions.
While at it, replace explicit array size calculations on changed
allocations with kvmalloc_array().
Purposedly not touching videobuf1, as it is deprecated, has only few
users remaining and would rather be seen removed instead.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a check for v4l2_dev to v4l2_async_notifier_register() as to fail as
early as possible since this will fail later in v4l2_async_test_notify().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'call_ptr_memop' can return NULL, so we must test its return value with
'IS_ERR_OR_NULL'. Otherwise, the test 'if (mem_priv)' is meaningless.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
this add functions for:
- remove buffers from src/dst queue by index
- remove exact buffer from src/dst queue
also extends m2m API to iterate over a list of src/dst buffers
in safely and non-safely manner.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add V4L2_CID_DIGITAL_GAIN to control explicitly digital gain.
We already have analogue gain control which the digital gain control
complements. Typically higher quality images are obtained using analogue
gain only as the digital gain does not add information to the image
(rather it may remove it).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds support for the three new SDR formats. These formats
were prefixed with "planar" indicating I & Q data are not interleaved
as in other formats. Here, I & Q data constitutes the top half and bottom
half of the received buffer respectively.
V4L2_SDR_FMT_PCU16BE - 14-bit complex (I & Q) unsigned big-endian sample
inside 16-bit. V4L2 FourCC: PC16
V4L2_SDR_FMT_PCU18BE - 16-bit complex (I & Q) unsigned big-endian sample
inside 18-bit. V4L2 FourCC: PC18
V4L2_SDR_FMT_PCU20BE - 18-bit complex (I & Q) unsigned big-endian sample
inside 20-bit. V4L2 FourCC: PC20
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The buffer cache should be synchronised in buffer preparation, not when
the buffer is queued to the device. Fix this.
Mmap buffers do not need cache synchronisation since they are always
coherent.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rename __qbuf_*() functions which are specific to a buffer type as
__prepare_*() which matches with what they do. The naming was there for
historical reasons; the purpose of the functions was changed without
renaming them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mutex that was initialised in v4l2_ctrl_handler_init_class() was not
destroyed in v4l2_ctrl_handler_free(). Do that.
Additionally, explicitly refer to the ctrl handler's mutex in mutex
initialisation for clarity.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sometimes the caller is already holding the control handler mutex and
using it to serialise something. Provide an unlocked variant of the same
function to be used in those cases.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All drivers have been converted from V4L2 OF to V4L2 fwnode. The V4L2 OF
framework is now unused. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pass the more generic fwnode_handle to the init function than the
device_node.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add fwnode matching to complement OF node matching. And fwnode may also be
an OF node.
Do not enable fwnode matching yet. It will replace OF matching soon.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The fwnode_handle is a more generic way than OF device_node to describe
firmware nodes. Instead of the OF API, use more generic fwnode API to
obtain the same information.
As the V4L2 fwnode support will be required by a small minority of e.g.
ACPI based systems (the same might actually go for OF), make this a module
instead of embedding it in the videodev module.
The origins of the V4L2 fwnode framework is in the V4L2 OF framework.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The VIDIOC_G/S_EDID ioctls can return valid data even if an error is returned.
Mark those ioctls accordingly. Rather than using an explicit 'if' to check for the
ioctl (as was done until now for VIDIOC_QUERY_DV_TIMINGS) just set a new flag in the
v4l2_ioctls array.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We should ensure that 'plane_no' is '< vb->num_planes' as done in
'vb2_plane_cookie' just a few lines below.
Fixes: e23ccc0ad9 ("[media] v4l: add videobuf2 Video for Linux 2 driver framework")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=Snzj
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Seeing the kunmap_atomic dma_buf_ops share the same name with a macro
in highmem.h, the former can be aliased if any dma-buf user includes
that header.
I'm personally trying to include highmem.h inside scatterlist.h and this
breaks the dma-buf code proper.
Christoph Hellwig suggested [1] renaming it and pushing this patch ASAP.
To maintain consistency I've renamed all four of kmap* and kunmap* to be
map* and unmap*. (Even though only kmap_atomic presently conflicts.)
[1] https://www.spinics.net/lists/target-devel/msg15070.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1492630570-879-1-git-send-email-logang@deltatee.com
The rotate control will modify the layout by definition. Always
set this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The format is used on the R-Car VSP1 video queues that carry
2-D histogram statistics data.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The format is used on the R-Car VSP1 video queues that carry
1-D histogram statistics data.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The metadata buffer type is used to transfer metadata between userspace
and kernelspace through a V4L2 buffers queue. It comes with a new
metadata capture capability and format description.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: removed left-over 'experimental' note]
[hans.verkuil@cisco.com: add newline after _v4l2-meta-format label]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide the frame structure and data layout of V4L2-PIX-FMT-INZI
format utilized by Intel SR300 Depth camera.
Signed-off-by: Evgeni Raikhel <evgeni.raikhel@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All control menus use the english capitalization rules of titles.
The only menu not following these rules is the RGB Quantization Range control
menu. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
