Maxim Semiconductor's PMIC MAX77686 has RTC IP which is
reused in the MAX77620/MAX20024 PMICs.
Add support for these devices in MAX77686 RTC driver. This
device does not have RTC alarm pending status outside of
RTC IP. The RTC IP is having separate I2C address for its
register access.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver uses the MODULE_ALIAS() macro to export a platform module alias
to allow the module to be autoloaded if the device is registered using the
legacy platform registration mechanism but the driver is always used by OF
only machines so the alias is not needed and should just be removed.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf85063_get_datetime() tries to handle a century bit but that bit is not
documented and the final value is never used anywhere else in the kernel.
Reviewed-by: Juergen Borleis <jbe@pengutronix.de>
Tested-by: Ulrich Ölmann <u.oelmann@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
drivers/rtc/rtc-vr41xx.c:229: warning: ‘vr41xx_rtc_alarm_irq_enable’ defined but not used
Apparently the conversion to alarm_irq_enable forgot to wire up the
callback.
Fixes: 16380c153a ("RTC: Convert rtc drivers to use the alarm_irq_enable method")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Kconfig option for rv3029 is not mentioning any part number, explicitly
show rv3029.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
as3722 RTC IRQ is nested threaded and wired to the as3722 inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps80031 RTC IRQ is nested threaded and wired to the tps80031
inerrupt controller. So, this flag is not required for nested irqs
anymore, since commit 3c646f2c6a ("genirq: Don't suspend
nested_thread irqs over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps65910 RTC IRQ is nested threaded and wired to the tps65910 inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
tps6586x RTC IRQ is nested threaded and wired to the tps6586x inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Palams RTC IRQ is nested threaded and wired to the Palmas inerrupt
controller. So, this flag is not required for nested irqs anymore,
since commit 3c646f2c6a ("genirq: Don't suspend nested_thread irqs
over system suspend") was merged.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RTC entries are mostly grouped by vendor. Move the few outliers in
place.
Also, change the one occurrence of 'nxp' to 'NXP' to make all NXP
entries consistent.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This driver adds support for the PIC32 real time clock and calendar
peripheral:
- reading and setting time
- alarms provided by dedicated IRQ
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Document the devicetree bindings for the real time clock found
on Microchip PIC32 class devices.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so unsupport UIE mode.
pcf8563 and hym8563 also have a minute accuracy and unsupport it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The alarm for rx8025 only has a minute accuracy, so round up to nearest
minute when setting alarm. Without doing this, rtctest blocks one day
after setting alarm to 5 seconds later.
pcf8563 and hym8563 also have similar handling.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ctrl1 register is accessed by alarm operations. But it is updated
in threaded interrupt handler without acquiring rtc->ops_lock.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When IRQ line for this chips is connected, devm_request_threaded_irq()
refuses to register irq handler with the following message.
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Few functions were marked inline even though they were relatively large
and sometimes used in multiple places. De-inline them to let the
compiler decide whether optimization makes sense. This fixes inline_hunt
report:
drivers/rtc/rtc-s5m.c: Deinline s5m8767_rtc_set_alarm_reg, save 704 bytes
drivers/rtc/rtc-s5m.c: Deinline s5m8767_wait_for_udr_update, save 192 bytes
Reported-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Makefile/Kconfig currently controlling compilation of this code is:
obj-$(CONFIG_RTC_CLASS) += rtc-core.o
rtc-core-y := class.o interface.o
drivers/rtc/Kconfig:menuconfig RTC_CLASS
drivers/rtc/Kconfig: bool "Real Time Clock"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the code there is no doubt it is builtin-only.
We don't replace module.h with init.h since the file does need
to know what a struct module is.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
When setting a new time/date the RTC's clock must be stopped first, in
order to write the time/date registers in an atomic manner.
So, this change stops the clock first and then writes the time/date
registers and the clock control register (to re-enable the clock) in one
turn.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Check if the RTC signals an invalid time/date (due to a battery power loss
for example). In this case ignore the time/date until it is really set again.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
By using i2c_smbus_read_i2c_block_data() the code is now much simpler.
While at it: when reading the RTC's seconds register, all time/date registers
are frozen until the RTC's year register is read. So it is important to read
all time/date registers in one turn to not lose a second event. Make it more
clear why the read must happen in this way.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 has an offset register, which can be used to make minor
adjustments to the clock rate to compensate for temperature or
a crystal that is not exactly right.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
clock offset may be set and read in decimal parts per billion
attribute is /sys/class/rtc/rtcN/offset
The attribute is only visible for rtcs that have set_offset implemented.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
A number of rtc devices, such as the NXP pcf2123 include a facility
to adjust the clock in order to compensate for temperature or a
crystal, capacitor, etc, that results in the rtc clock not running
at exactly 32.768 kHz.
Data sheets I have seen refer to this as a clock offset, and measure it
in parts per million, however they often reference ppm to 2 digits of
precision, which makes integer ppm less than ideal.
We use parts per billion, which more than covers the precision needed
and works nicely within 32 bits
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix a scheduling while atomic issue caused by rv8803_set_time()
holding a spinlock during the call to i2c_smbus_read_byte_data().
Signed-off-by: Oleksij Rempel <fixed-term.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for RTC controller found on Alphascale asm9260
SoC.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To make RTC block of MAX77686/MAX77802 as independent driver,
move the registration of i2c device, regmap for register access
and irq_chip for interrupt support inside the RTC driver.
Removed the same initialisation from MFD driver.
Having this change will allow to reuse this driver for different
PMIC/devices from Maxim Semiconductor if they kept same RTC IP on
different PMIC. Some of examples as PMIC MAX77620, MAX20024 where
same RTC IP used and hence driver for these chips will use this
driver only for RTC support.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is different RTC I2C address for RTC block in MAX77686.
Driver is creating dummy i2c client for this address to access
the register of this IP block.
As there is no call to i2c_get_clientdata() for rtc_i2c client,
there is no need to store pointer and hence removing the call
to set client data for rtc i2c client.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Get rid of referring parent device info for register access
all the places by making regmap as part of max77686 rtc
device info. This will also remove the need of storing parent
device info in max77686 rtc device info as this is no more required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
rtc_regmap should be used to access all RTC registers instead
of parent regmap regardless of what chip or property have it.
This makes the register access uniform and extendible for other
chips.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix following check patch error in rtc-max77686 driver:
- Alignment should match open parenthesis.
- braces {} should be used on all arms of this statement.
- Prefer using the BIT macro
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
At the moment the "sun6i" RTC drivers depends on having two specific
SoC families selected.
The Allwinner A64 SoC has the same RTC, so extend the Kconfig option
to allow inclusion of the driver for all Allwinner SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The RX6110 comes in two different variants: SPI and I2C.
This driver only supports the SPI variant.
If the need ever arises to also support the I2C variant, this driver
could easily be refactored to support both cases.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the binding documentation for the Epson RX6110 RTC.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
pcf2123 data sheet recommends a software reset when the chip
is first powered on. This change avoids resetting the chip
every time the driver is loaded, which has some negative effects.
There are several registers including a clock rate adjustment that really
should survive a reload of the driver (or reboot).
In addition, stopping and restarting the clock to verify the chip is
there is not a good thing once the time is set.
According to the data sheet, the seconds register has a 1 in
the high bit when the voltage has gotten low. We check for this
condition, as well as whether the time retrieved from the chip is
valid. We reset the rtc only if the time is not reliable and valid.
This is sufficient for checking for the presence of the chip,
as either all zeros or all 0xff will result in an invalid time/date
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Refactor chip reset items into its own function, isolating it from
the rest of the device probe.
Subsequent commits will avoid calling this code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add new functions pcf2123_write(), and pcf2123_write_reg().
Use named defines for the values being written.
This improves modularity and readability, and reduces lines of code.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Put read operations into a function.
This improves modularity and readability.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add defines for all 16 registers in the pcf2123.
Add defines for useful bits from several registers
I've tried to document all the registers, and
as best as possible, all the special bits they employ
Use BIT() wherever possible in the bit definitions
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The function measurement block must not cross a page boundary. Ensure
that by raising the alignment requirement to the smallest power of 2
larger than the size of the fmb.
Fixes: d0b088531 ("s390/pci: performance statistics and debug infrastructure")
Cc: stable@vger.kernel.org # v3.8+
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iBFT table only specifies a prefix length, not a netmask.
And the netmask is pretty much pointless for IPv6.
So introduce a new attribute 'prefix-len'.
Some older user-space code might rely on the netmask attribute
being present, so we should always display it.
Changes from v1:
- Combined two patches into one
Changes from v2:
- Cleaned up/corrected wording for patch description
v3: [Put Hannes back as author]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Lee Duncan <lduncan@suse.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
* pm-cpufreq: (94 commits)
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
intel_pstate: Optimize calculation for max/min_perf_adj
intel_pstate: Remove extra conversions in pid calculation
cpufreq: Move scheduler-related code to the sched directory
Revert "cpufreq: postfix policy directory with the first CPU in related_cpus"
cpufreq: Reduce cpufreq_update_util() overhead a bit
cpufreq: Select IRQ_WORK if CPU_FREQ_GOV_COMMON is set
cpufreq: Remove 'policy->governor_enabled'
cpufreq: Rename __cpufreq_governor() to cpufreq_governor()
cpufreq: Relocate handle_update() to kill its declaration
cpufreq: governor: Drop unnecessary checks from show() and store()
cpufreq: governor: Fix race in dbs_update_util_handler()
cpufreq: governor: Make gov_set_update_util() static
cpufreq: governor: Narrow down the dbs_data_mutex coverage
cpufreq: governor: Make dbs_data_mutex static
cpufreq: governor: Relocate definitions of tuners structures
cpufreq: governor: Move per-CPU data to the common code
cpufreq: governor: Make governor private data per-policy
...
Laxman Dewangan
Javier Martinez Canillas
Alexandre Belloni
Geert Uytterhoeven
Grygorii Strashko
Soren Brinkmann
Joshua Henderson
Akinobu Mita
Krzysztof Kozlowski
Paul Gortmaker
Juergen Borleis
Joshua Clayton
Oleksij Rempel
Oleksij Rempel
Andre Przywara
Steffen Trumtrar
Sebastian Ott
Hannes Reinecke
Rafael J. Wysocki