Commit Graph

411 Commits

Author SHA1 Message Date
Jeff Skirvin 726980d569 isci: Terminate outstanding TCs on TX/RX RNC suspensions.
TCs must only be terminated when RNCs are suspended.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 14:33:37 -07:00
Jeff Skirvin ac78ed0f78 isci: Handle all suspending TC completions
Add comprehensive decode for all TC completions that generate RNC
suspensions.

Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 14:33:37 -07:00
Jeff Skirvin 56d7c013e7 isci: Fixed bug in resumption from RNC Tx/Rx suspend state.
The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 14:33:36 -07:00
Jeff Skirvin 6f48844e3f isci: Manage the link layer hang detect timer for RNC suspensions.
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU.  The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.

This change enables the timer with the minimum period at the point
when the suspension is requested.

Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 14:33:36 -07:00
Dan Williams fc25f79af3 isci: fix oem parameter validation on single controller skus
OEM parameters [1] are parsed from the platform option-rom / efi
driver.  By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.

Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.

[1] the platform specific set of phy address, configuration,and analog
    tuning values

[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:29 -07:00
Maciej Trela 08e73be56b isci: enable BCN in sci_port_add_phy()
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:28 -07:00
Andrzej Jakowski 6119908f0f isci: Changes in COMSAS timings enabling ISCI to detect buggy disc drives.
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.

Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:28 -07:00
Dan Williams d1dc5e2d21 isci: kill isci_host.shost
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.

Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:13 -07:00
Dan Williams 2396a2650a isci: fix interrupt disable
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts.  Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.

The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.

Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams 50a92d9314 isci: fix 'link-up' events occur after 'start-complete'
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing.  However, the implementation is not correctly syncing with the
port configuration agent.  In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.

Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.

Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams eb608c3cb3 isci: fix controller stop
1/ notify waiters when controller stop completes (fixes 10 second stall
   unloading the driver)
2/ make sure phy stop is after port and device stop

Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams abec912d71 isci: refactor initialization for S3/S4
Based on an original implementation by Ed Nadolski and Artur Wojcik

In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init().  Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations).  The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().

The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful.  In the case of isci we'll just re-init using a subset of the
normal driver load path.

[clean up some unused / mis-indented function definitions in host.h]

Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams ae904d15cf isci: kill isci_port.domain_dev_list
Another unused field, and isci_port_init is overkill.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams 1844e4789f isci: kill ->status, and ->state_lock in isci_host
They serve no incremental purpose over the existing sas_ha state.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Tom Jackson 944b787d0a isci: Don't filter BROADCAST CHANGE primitives
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer.  The other BC primitives have been
added to the sci_phy_event_handler()

Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:12 -07:00
Dan Williams c79dd80d73 isci: kill sci_phy_protocol and sci_request_protocol
Holdovers from the initial driver cleanup, replace with enum sas_protocol.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:11 -07:00
Dan Williams 11cc51835a isci: kill ->is_direct_attached
domain_device ->parent conveys the same information.

Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:11 -07:00
Dan Williams 14e99b4a3f isci: improve 'invalid state' warnings
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).

Fix up the rnc warnings to use the state name.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2012-05-17 12:27:11 -07:00
Linus Torvalds 424a6f6ef9 SCSI updates on 20120319
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
 CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
 2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
 tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
 +AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
 uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
 =1TxB
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

SCSI updates from James Bottomley:
 "The update includes the usual assortment of driver updates (lpfc,
  qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
  amount of infrastructure work in the SAS library and transport class
  as well as an iSCSI update.  There's also a new SCSI based virtio
  driver."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
  [SCSI] qla4xxx: Update driver version to 5.02.00-k15
  [SCSI] qla4xxx: trivial cleanup
  [SCSI] qla4xxx: Fix sparse warning
  [SCSI] qla4xxx: Add support for multiple session per host.
  [SCSI] qla4xxx: Export CHAP index as sysfs attribute
  [SCSI] scsi_transport: Export CHAP index as sysfs attribute
  [SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
  [SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
  [SCSI] pm8001: fix endian issue with code optimization.
  [SCSI] pm8001: Fix possible racing condition.
  [SCSI] pm8001: Fix bogus interrupt state flag issue.
  [SCSI] ipr: update PCI ID definitions for new adapters
  [SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
  [SCSI] isci: improvements in driver unloading routine
  [SCSI] isci: improve phy event warnings
  [SCSI] isci: debug, provide state-enum-to-string conversions
  [SCSI] scsi_transport_sas: 'enable' phys on reset
  [SCSI] libsas: don't recover end devices attached to disabled phys
  [SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
  [SCSI] libsas: set attached device type and target protocols for local phys
  ...
2012-03-22 12:55:29 -07:00
Linus Torvalds 9f3938346a Merge branch 'kmap_atomic' of git://github.com/congwang/linux
Pull kmap_atomic cleanup from Cong Wang.

It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().

Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.

* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
  feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
  highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
  drbd: remove the second argument of k[un]map_atomic()
  zcache: remove the second argument of k[un]map_atomic()
  gma500: remove the second argument of k[un]map_atomic()
  dm: remove the second argument of k[un]map_atomic()
  tomoyo: remove the second argument of k[un]map_atomic()
  sunrpc: remove the second argument of k[un]map_atomic()
  rds: remove the second argument of k[un]map_atomic()
  net: remove the second argument of k[un]map_atomic()
  mm: remove the second argument of k[un]map_atomic()
  lib: remove the second argument of k[un]map_atomic()
  power: remove the second argument of k[un]map_atomic()
  kdb: remove the second argument of k[un]map_atomic()
  udf: remove the second argument of k[un]map_atomic()
  ubifs: remove the second argument of k[un]map_atomic()
  squashfs: remove the second argument of k[un]map_atomic()
  reiserfs: remove the second argument of k[un]map_atomic()
  ocfs2: remove the second argument of k[un]map_atomic()
  ntfs: remove the second argument of k[un]map_atomic()
  ...
2012-03-21 09:40:26 -07:00
Linus Torvalds 69a7aebcf0 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "It's indeed trivial -- mostly documentation updates and a bunch of
  typo fixes from Masanari.

  There are also several linux/version.h include removals from Jesper."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
  kcore: fix spelling in read_kcore() comment
  constify struct pci_dev * in obvious cases
  Revert "char: Fix typo in viotape.c"
  init: fix wording error in mm_init comment
  usb: gadget: Kconfig: fix typo for 'different'
  Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
  writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
  writeback: fix typo in the writeback_control comment
  Documentation: Fix multiple typo in Documentation
  tpm_tis: fix tis_lock with respect to RCU
  Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
  Doc: Update numastat.txt
  qla4xxx: Add missing spaces to error messages
  compiler.h: Fix typo
  security: struct security_operations kerneldoc fix
  Documentation: broken URL in libata.tmpl
  Documentation: broken URL in filesystems.tmpl
  mtd: simplify return logic in do_map_probe()
  mm: fix comment typo of truncate_inode_pages_range
  power: bq27x00: Fix typos in comment
  ...
2012-03-20 21:12:50 -07:00
Cong Wang 77dfce076c scsi: remove the second argument of k[un]map_atomic()
Signed-off-by: Cong Wang <amwang@redhat.com>
2012-03-20 21:48:19 +08:00
Andrzej Jakowski 13de2c5419 [SCSI] isci: improvements in driver unloading routine
This patch fixes scenario where driver removal should be possible
only when driver is in READY state. Also it removes redundant
invocation of routine disabling SCU interrupts - this method is
called somewhere else in driver deinitialization path.

Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 16:24:41 -06:00
Dan Williams e462116afb [SCSI] isci: improve phy event warnings
isci occasionally spews messages like:

isci 0000:03:00.0: sci_phy_event_handler: PHY starting substate machine received unexpected event_code b3940000

...which is not very helpful, since we don't know which controller,
which phy, the exact state, or a decode of the event.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 16:24:13 -06:00
Dan Williams d7a0ccdd9b [SCSI] isci: debug, provide state-enum-to-string conversions
Debugging the driver requires tracing the state transtions and tracing
state names is less work than decoding numbers.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 16:23:15 -06:00
Dan Williams 9508a66f89 [SCSI] libsas: async ata scanning
libsas ata error handling is already async but this does not help the
scan case.  Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.

Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.

Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.

Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:35:41 -06:00
Dan Williams 5a99832829 [SCSI] isci: remove IDEV_EH hack to disable "discovery-time" ata resets
Prior to commit 61aaff49 "isci: filter broadcast change notifications
during SMP phy resets" we borrowed the MVS_DEV_EH approach from the
mvsas driver for preventing ->lldd_I_T_nexus_reset() events during ata
discovery.  This hack was protecting against the old ->phy_reset() in
ata_bus_probe(), but since the conversion to the new error handling this
hack is preventing resets from reaching ata devices.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:16:52 -06:00
Dan Williams 6a719391e4 [SCSI] isci: remove bus and reset handlers
Remove ->eh_device_reset_handler() and ->eh_bus_reset_handler() for the
same reason they are not implemented for libata hosts, they cannot be
implemented reliably with ata-eh.  ATA error recovery wants to divert
all resets to the eh thread and wait for completion, these handlers may
be invoked from a non-blocking ioctl.

The other path they are called from is libsas-eh, and if we escalate
past I_T_nexus reset we have larger problems i.e. tear down all
in-flight commands in the domain potentially without notification to the
lldd if it has chosen not to implement ->lldd_clear_nexus_port() /
->lldd_clear_nexus_ha().

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:16:05 -06:00
Dan Williams 687833a03b [SCSI] isci: ->lldd_ata_check_ready handler
Report to libata whether the link to the given domain_device is up and the
signature fis has been received.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:15:07 -06:00
Dan Williams 43a5ab151f [SCSI] isci: stop interpreting ->lldd_lu_reset() as an ata soft-reset
Driving resets from libsas-eh is pre-mature as libata will make a
decision about performing a softreset.  Currently libata determines
whether to perform a softreset based on ata_eh_followup_srst_needed(),
and none of those conditions apply to isci.

Remove the srst implementation and translate ->lldd_lu_reset() for ata
devices as a request to drive a reset via libata-eh.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:13:40 -06:00
Dan Williams 9277699121 [SCSI] isci: fix interpretation of "hard" reset
A hard reset to isci in the direct-attached case is one where the driver
internally manages debouncing the link.  In the sas-expander-attached
case a hard reset is one that clears affiliations.  The driver should
not be prematurely dropping affiliations at run time, that decision (to
force expander hard resets to ata devices) is left to userspace to
manage.  So, arrange for I_T_nexus resets to be sas-link-resets in the
expander-attached case and isci-hard-resets in the direct-attached case.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:11:54 -06:00
Dan Williams fca4ecbdc4 [SCSI] isci: kill isci_port->status
It only tracks whether the port is stopping in order to gate new devices
being discovered while the port is stopping.  However, since the check
and subsequent handling is unlocked there is nothing to stop the port
from going down immediately after the check.

Driver is already prepared to handle devices arriving on stale ports,
and those will be cleaned up by an eventual ->lldd_dev_gone()
notification.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:11:19 -06:00
Dan Williams c132f69208 [SCSI] isci: kill iphy->isci_port lookups
This field is a holdover from the OS abstraction conversion.  The stable
phy to port lookups are done via iphy->ownining_port under scic_lock.
After this conversion to use port->lldd_port the only volatile lookup is
the initial lookup in isci_port_formed().  After that point any lookup
via a successfully notified domain_device is guaranteed to be valid
until the domain_device is destroyed.

Delete ->start_complete as it is only set once and is set as a
consequence of the port going link up, by definition of getting a port
formed event the port is "ready".

While we are correcting port lookups also move the asd_sas_port table
out from under the isci_port.  This is to preclude any temptation to use
container_of() to convert an asd_sas_port to an isci_port, the
association is dynamic and under libsas control.

Tested-by: Maciej Trela <maciej.trela@intel.com>
[dmilburn@redhat.com: fix i686 compile error]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 15:05:05 -06:00
Dan Williams f41a0c441c [SCSI] libsas: fix sas_find_local_phy(), take phy references
In the direct-attached case this routine returns the phy on which this
device was first discovered.  Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.

In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it.  However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached.  This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.

Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-29 13:01:06 -06:00
Dan Williams 312d3e5611 [SCSI] libsas: remove ata_port.lock management duties from lldds
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock.  The lock is held by the ata
->queuecommand() path.  mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done().  This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 13:50:12 -06:00
Dan Williams b1124cd3ec [SCSI] libsas: introduce sas_drain_work()
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:

  1/ form the port and find the direct attached device

  2/ if the attached device is an expander perform domain discovery

A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event).  Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.

drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight.  A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'.  As Tejun notes:

  "For now, I think it would be best to add private wrapper in libsas to
   support deferring unchained work items while draining."

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 13:48:51 -06:00
Dan Williams 6f4e75a49f [SCSI] libsas: kill sas_slave_destroy
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 13:36:36 -06:00
Dave Jiang 3d2d752549 [SCSI] isci: T10 DIF support
This allows the controller to do WRITE_INSERT and READ_STRIP for SAS
disks that support protection information. SAS disks must be formatted
with protection information to use this feature via sg_format.

  sg3_utils-1.32 -- sg_format version 1.19 20110730
  sg_format usage:
  sg_format --format --verbose --pinfo /dev/sda

Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:14:24 -06:00
Marcin Tomczak e5cc6aa4b6 [SCSI] isci: enable clock gating
Enabling clock gating for power savings on entry to controller ready
state. Disable SCU clock gating for power savings on exit from the
controller ready state.

The gating is fully automated by silicon after setting the mode.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:09:00 -06:00
Dave Jiang 6d7938f46f [SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.

Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-18 08:37:00 -06:00
Jesper Juhl a2888ec985 SCSI, ISCSI: Just #include "host.h" once in host.c
There's no need to include the header twice.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-02-10 09:52:19 +01:00
Marcin Tomczak 05b080fc93 [SCSI] isci: fix, prevent port from getting stuck in the 'configuring' state
When expander connected in x2 or x4 mode and with IO runnning, if
a cable from wideport is plugged out from the phy, IO's start failing
on all the targets.

Observed that when cable is pulled with IO running, cominit is
happening on all the links and IO's start dropping to 0 and eventually
the whole IO fails. Second observation, target is trying to open and
SCU is responding with "Open reject no destination".

A cause of the problem is when the port went from the "ready
configuring substate" back to "ready configuring substate" as a result
of phy being pulled off, scic suspended the port task scheduler
register. As a result no IO was allowed and in the "substate
configuring enter" routine the IO never goes back to 0. As a result
the port never comes out of "ready substate configuring".

The patch adds a mechanism of activate and deactivate phy when a port
link up, which fixes the problem.

Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:48:02 +04:00
Marcin Tomczak 0953dbea1d [SCSI] isci: fix start OOB
Split scu_link_layer_start_oob function to reset and enable and
add flush after all steps.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:47:27 +04:00
Marcin Tomczak be77834181 [SCSI] isci: fix io failures while wide port links are coming up
When the first phy of a wide port comes up, don't report the port ready
yet, always wait for 250 miliseconds then config the port with all phys
added to the port. So that we can avoid reporting wide port device too
early to kernel, which caused the first IOs (report luns, inquirys)
failed due to not all the phys are configured into its port. Changes
also made that the phys in a wide port don't need to go through half
second wait time for consuming power.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:46:59 +04:00
Marcin Tomczak 472d4d2cfb [SCSI] isci: allow more time for wide port targets
When hot insert the wide port device through the mini-sas port,
the first IOs (Report Luns or Inquiry) may fail due to the device
trying to open to a SCU phy that is still in suspended state. This
IO failure causes the wide port device stuck in UPDATING_PORT_WIDTH
state.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:46:18 +04:00
Bartek Nowakowski 7e629841b8 [SCSI] isci: enable wide port targets
Arrange for task_contexts prepared for the wide targets to account for
all the attached phys in the port.

Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:45:43 +04:00
Marcin Tomczak d4ec1cf61f [SCSI] isci: Fix IO fails when pull cable from phy in x4 wideport in MPC mode.
Failure seen pulling a cable from a x4 port configured in manual port
configuration (MPC) mode (MPC mode is set by the the OEM paramaters
provided by the platform or isci_firmware.bin).  While IO running to
devices behind and expander, plugging out the cable from phy is causing
IO failures and IO drops on disks and never recover.

It happens because during link up/down the phy were being taken out of
the port.

Fix: during link down the phy is kept in the same logical port.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:45:19 +04:00
Dan Williams d3fd2e2bc2 [SCSI] isci: update version to 1.1
Bump the version now that the driver has atapi support and the initial
round of hotplug fixes.  The EXPERIMENTAL tag should have been removed a
while back.  While we're here also kill the "select SCSI_SAS_HOST_SMP"
as the build error was separately fixed by commit d962480e "[SCSI]
libsas: fix try_test_sas_gpio_gp_bit() build error".

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:44:54 +04:00
Maciej Trela 27234ab44f [SCSI] isci: remove unused 'isci_tmf->device' field
As the field was never set, isci_print_tmf() using 'isci_tmf->device'
sometimes causes a kernel crash if the dev_dbg() statement is enabled.
Remove the unused field both from isci_tmf struct definition and from
isci_print_tmf()

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:44:15 +04:00
Jeff Skirvin be168a3b89 [SCSI] isci: link speeds default to gen 2
Gen-3 operation is marginal, default to gen-2 for now.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:43:59 +04:00
Marcin Tomczak 6024d38b86 [SCSI] isci: performance-fix, shorten default "no outbound task" timeout
"No task timeout timer reduced from 20 to 2 This timer controls how
long the SCU hardware will hold open the TX side of the connection
before sending a DONE.  The timer allows the hardware to attempt to
optimize the DONE/CLOSE behavior to allow for new COMMAND IU to be
posted.  In practice closing the connection quicker is better."

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:43:39 +04:00
Jeff Skirvin 9fee607f0b [SCSI] isci: oem parameter format v1.3 (cable select)
v1.3 allows the attenuation of the attached cables to be specified to
the driver in terms of 'short', 'medium', and 'long' (see probe_roms.h).
These settings (per phy) are retrieved from the platform oem-parameters
(BIOS rom) or via a module parameter override.

Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:43:04 +04:00
Dave Jiang 594e566ae5 [SCSI] isci: oem parameter format v1.1 (ssc select)
v1.1 allows finer grained tuning of the SSC (spread-spectrum-clocking)
settings for SAS and SATA.  See notes in probe_roms.h

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:42:00 +04:00
Jeff Skirvin afd13a1f2b [SCSI] isci: update afe (analog-front-end) recipe for C1
C1 silicon requires updates to the phy tuning recipe and also support
for user provided cable selects (per-phy) for short, medium, and long
cables.  Default to 'short' awaiting support for selecting the cable via
oem parameters.

Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:40:29 +04:00
Dan Williams 2e5da889d4 [SCSI] isci: cleanup oem parameter and recipe handling
Before updating the code to support the latest platform updates and
silicon revision cleanup some of the long deref chains.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:39:52 +04:00
Ben Hutchings 7d99b3abaf [SCSI] isci, firmware: Remove isci fallback parameter blob and generator
This parameter blob and generator program have been moved to the
linux-firmware.git repository.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 11:34:37 +04:00
Andrzej Jakowski 7000f7c71e [SCSI] isci: overriding max_concurr_spinup oem parameter by max(oem, user)
Fixes bug where max_concurr_spinup oem parameter should be
overriden by max_concurr_spinup user parameter. Override should
happen only when max_concurr_spinup user parameter is specified
in command line (greater than 0). Also this fix shortens variables
representing max_conxurr_spinup for oem and user parameters.

Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:23:18 +04:00
Dan Williams 52d7463433 [SCSI] isci: revert bcn filtering
The initial bcn filtering implementation was validated on a kernel
baseline that predated the switch to new libata error handling.  Also,
prior to that conversion we borrowed the mvsas MVS_DEV_EH approach to
prevent the unwanted extra ap->ops->phy_reset(ap) that occurred in the
ata_bus_probe() path.

After the conversion to new libata eh resets at discovery are more
frequent and get filtered prematurely by IDEV_EH.  The result is that
our bcn filtering has been blocked from running and at discovery and it
appears to stall discovery completion to the point of triggering hung
task timeouts.  So, revert the implementation for now.  When it returns
it will go into libsas proper.

The domain rediscovery that takes place due to ->lldd_I_T_nexus_reset()
events should now be properly waited for by the ata_port_wait_eh() call
in ata_port_probe().  So the hard coded delay in the isci
->lldd_I_T_nexus_reset() and other libsas drivers should help debounce
the libsas thread from seeing temporary device removals.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:23:01 +04:00
Jeff Skirvin 8e35a1398c [SCSI] isci: Fix hard reset timeout conditions.
A hard reset can timeout before or after the last phy in the
port goes away.  If after, then notify the OS that the last
phy has failed.

The recovery for the failed hard reset has been removed.
This recovery code was unecessary in that the link would
recover from the failure normally by a new link reset sequence
or hotplug of the remote device.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:22:41 +04:00
Jeff Skirvin 5412e25c55 [SCSI] isci: No need to manage the pending reset bit on pending requests.
The lldd does not need to look at or manage the pending device
reset bit in pending sas_tasks.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:20:28 +04:00
Jeff Skirvin 3b34c169f8 [SCSI] isci: Remove redundant isci_request.ttype field.
Use the existing IREQ_TMF flag as a request type indicator.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:19:47 +04:00
Jeff Skirvin 98145cb722 [SCSI] isci: Fix task management for SMP, SATA and on dev remove.
libsas uses the LLDD abort task interface to handle I/O timeouts
in the SATA/STP and SMP discovery paths, so this change will terminate
STP/SMP requests. Also, if the device is gone, the lldd will prevent
libsas from further escalations in the error handler.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:17:48 +04:00
Jeff Skirvin db49c2d037 [SCSI] isci: No task_done callbacks in error handler paths.
libsas will cleanup pending sas_tasks after error handler
path functions are called; do not call task_done callbacks.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:17:04 +04:00
Jeff Skirvin b343dff1a2 [SCSI] isci: Handle task request timeouts correctly.
In the case where "task" requests timeout (note that this class of
requests can also include SATA/STP soft reset FIS transmissions),
handle the case where the task was being managed by some call to
terminate the task request by completing both the tmf and the aborting
process.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:16:23 +04:00
Jeff Skirvin d689168222 [SCSI] isci: Fix tag leak in tasks and terminated requests.
Make sure terminated requests and completed task tags are freed.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:16:04 +04:00
Jeff Skirvin c2cb8a5fd7 [SCSI] isci: Immediately fail I/O to removed devices.
In the case where an I/O fails to start in isci_request_execute,
only allow retries if the device is not already gone.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:15:17 +04:00
Jeff Skirvin 0e2e27990e [SCSI] isci: Lookup device references through requests in completions.
The LLDD needs to obtain a reference to the device through the request
itself and not through the domain_device, because the
domain_device.lldd_dev is set to NULL early in the lldd_dev_gone call.
This relies on the fact that the isci_remote_device object is keeping a
seperate reference count of outstanding requests.  TODO: unify the
request count tracking with the isci_remote_device kref.

The failure signature of this condition looks like the following
log, where the important bits are the call to lldd_dev_gone followed
by a crash in isci_terminate_request_core:

[  229.151541] isci 0000:0b:00.0: isci_remote_device_gone: domain_device = ffff8801492d4800, isci_device = ffff880143c657d0, isci_port = ffff880143c63658
[  229.166007] isci 0000:0b:00.0: isci_remote_device_stop: isci_device = ffff880143c657d0
[  229.175317] isci 0000:0b:00.0: isci_terminate_pending_requests: idev=ffff880143c657d0 request=ffff88014741f000; task=ffff8801470f46c0 old_state=2
[  229.189702] isci 0000:0b:00.0: isci_terminate_request_core: device = ffff880143c657d0; request = ffff88014741f000
[  229.201339] isci 0000:0b:00.0: isci_terminate_request_core: before completion wait (ffff88014741f000/ffff880149715ad0)
[  229.213414] isci 0000:0b:00.0: sci_controller_process_completions: completion queue entry:0x8000a0e9
[  229.214401] BUG: unable to handle kernel NULL pointer dereference at 0000000000000228
[  229.214401] IP:jdskirvi-testlbo [<ffffffffa00a58be>] sci_request_completed_state_enter+0x50/0xafb [isci]
[  229.214401] PGD 13d19e067 PUD 13d104067 PMD 0
[  229.214401] Oops: 0000 [#1] SMP
[  229.214401] CPU 0 x kernel: [  226
[  229.214401] Modules linked in: ipv6 dm_multipath uinput nouveau snd_hda_codec_realtek snd_hda_intel ttm drm_kms_helper drm snd_hda_codec snd_hwdep snd_pcm snd_timer i2c_algo_bit isci snd libsas ioatdma mxm_wmi iTCO_wdt soundcore snd_page_alloc scsi_transport_sas iTCO_vendor_support wmi dca video i2c_i801 i2c_core [last unloaded: speedstep_lib]
[  229.214401]
[  229.214401] Pid: 5, comm: kworker/u:0 Not tainted 3.0.0-isci-11.7.29+ #30.353196] Buffer  Intel Corporation Stoakley/Pearlcity Workstation
[  229.214401] RIP: 0010:[<ffffffffa00a58be>] I/O error on dev [<ffffffffa00a58be>] sci_request_completed_state_enter+0x50/0xafb [isci]
[  229.214401] RSP: 0018:ffff88014fc03d20  EFLAGS: 00010046
[  229.214401] RAX: 0000000000000000 RBX: ffff88014741f000 RCX: 0000000000000000
[  229.214401] RDX: ffffffffa00b2c90 RSI: 0000000000000017 RDI: ffff88014741f0a0
[  229.214401] RBP: ffff88014fc03d90 R08: 0000000000000018 R09: 0000000000000000
[  229.214401] R10: 0000000000000000 R11: ffffffff81a17d98 R12: 000000000000001d
[  229.214401] R13: ffff8801470f46c0 R14: 0000000000000000 R15: 0000000000008000
[  229.214401] FS:  0000000000000000(0000) GS:ffff88014fc00000(0000) knlGS:0000000000000000
[  229.214401] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  229.214401] CR2: 0000000000000228 CR3: 000000013ceaa000 CR4: 00000000000406f0
[  229.214401] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  229.214401] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  229.214401] Process kworker/u:0 (pid: 5, threadinfo ffff880149714000, task ffff880149718000)
[  229.214401] Call Trace:
[  229.214401]  <IRQ>
[  229.214401]  [<ffffffffa00aa6ce>] sci_change_state+0x4a/0x4f [isci]
[  229.214401]  [<ffffffffa00a4ca6>] sci_io_request_tc_completion+0x79c/0x7a0 [isci]
[  229.214401]  [<ffffffffa00acf35>] sci_controller_process_completions+0x14f/0x396 [isci]
[  229.214401]  [<ffffffffa00abbda>] ? spin_lock_irq+0xe/0x10 [isci]
[  229.214401]  [<ffffffffa00ad2cf>] isci_host_completion_routine+0x71/0x2be [isci]
[  229.214401]  [<ffffffff8107c6b3>] ? mark_held_locks+0x52/0x70
[  229.214401]  [<ffffffff810538e8>] tasklet_action+0x90/0xf1
[  229.214401]  [<ffffffff81054050>] __do_softirq+0xe5/0x1bf
[  229.214401]  [<ffffffff8106d9d1>] ? hrtimer_interrupt+0x129/0x1bb
[  229.214401]  [<ffffffff814ff69c>] call_softirq+0x1c/0x30
[  229.214401]  [<ffffffff8100bb67>] do_softirq+0x4b/0xa3
[  229.214401]  [<ffffffff81053d84>] irq_exit+0x53/0xb4
[  229.214401]  [<ffffffff814fffe7>] smp_apic_timer_interrupt+0x83/0x91
[  229.214401]  [<ffffffff814fee53>] apic_timer_interrupt+0x13/0x20
[  229.214401]  <EOI>
[  229.214401]  [<ffffffff814f7ad4>] ? retint_restore_args+0x13/0x13
[  229.214401]  [<ffffffff8107af29>] ? trace_hardirqs_off+0xd/0xf
[  229.214401]  [<ffffffff8104ea71>] ? vprintk+0x40b/0x452
[  229.214401]  [<ffffffff814f4b5a>] printk+0x41/0x47
[  229.214401]  [<ffffffff81314484>] __dev_printk+0x78/0x7a
[  229.214401]  [<ffffffff8131471e>] dev_printk+0x45/0x47
[  229.214401]  [<ffffffffa00ae2a3>] isci_terminate_request_core+0x15d/0x317 [isci]
[  229.214401]  [<ffffffffa00af1ad>] isci_terminate_pending_requests+0x1a4/0x204 [isci]
[  229.214401]  [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[  229.214401]  [<ffffffffa00a7d9e>] isci_remote_device_nuke_requests+0xa6/0xff [isci]
[  229.214401]  [<ffffffffa00a811a>] isci_remote_device_stop+0x7c/0x166 [isci]
[  229.214401]  [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[  229.214401]  [<ffffffffa00a827a>] isci_remote_device_gone+0x76/0x7e [isci]
[  229.214401]  [<ffffffffa002363e>] sas_notify_lldd_dev_gone+0x34/0x36 [libsas]
[  229.214401]  [<ffffffffa0023945>] sas_unregister_dev+0x57/0x9c [libsas]
[  229.214401]  [<ffffffffa00239c0>] sas_unregister_domain_devices+0x36/0x65 [libsas]
[  229.214401]  [<ffffffffa0022cb8>] sas_deform_port+0x72/0x1ac [libsas]
[  229.214401]  [<ffffffffa00229f6>] ? sas_phye_oob_error+0xc3/0xc3 [libsas]
[  229.214401]  [<ffffffffa0022a34>] sas_phye_loss_of_signal+0x3e/0x42 [libsas]

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:14:44 +04:00
Linus Torvalds ec7ae51753 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
  [SCSI] qla4xxx: export address/port of connection (fix udev disk names)
  [SCSI] ipr: Fix BUG on adapter dump timeout
  [SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
  [SCSI] hpsa: change confusing message to be more clear
  [SCSI] iscsi class: fix vlan configuration
  [SCSI] qla4xxx: fix data alignment and use nl helpers
  [SCSI] iscsi class: fix link local mispelling
  [SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
  [SCSI] aacraid: use lower snprintf() limit
  [SCSI] lpfc 8.3.27: Change driver version to 8.3.27
  [SCSI] lpfc 8.3.27: T10 additions for SLI4
  [SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
  [SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
  [SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
  [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
  [SCSI] megaraid_sas: Changelog and version update
  [SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
  [SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
  [SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
  [SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
  ...
2011-10-28 16:44:18 -07:00
Dan Williams ac013ed1cb [SCSI] isci: export phy events via ->lldd_control_phy()
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy().  Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.

These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
 * /sys/class/sas_phy/<phyX>/invalid_dword_count
 * /sys/class/sas_phy/<phyX>/running_disparity_error_count
 * /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
 * /sys/class/sas_phy/<phyX>/phy_reset_problem_count

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:24:26 -05:00
Jeff Skirvin cdd05f05b4 [SCSI] isci: The port state should be set to stopping on the last phy.
Fixes a bug where any phy removed from the port set the port
state to "stopping" - do this only when the last phy removed
from the port.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:22:28 -05:00
Jeff Skirvin 7582ba8bdf [SCSI] isci: fix decode of DONE_CRC_ERR TC completion status
DONE_CRC_ERR is not a RNC suspension condition, so do not change the
state to expect the incoming suspension notification.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
[djbw: dropped DONE_CMD_LL_R_ERR change]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:21:51 -05:00
Jeff Skirvin cd06b9bae1 [SCSI] isci: SATA/STP I/O is only returned in the normal path to libsas
Since libsas has it's own means to escalate SATA/STP device error
handling depending on task status codes, return all SATA/STP I/O
on the normal path.

i.e. skip sas_task_abort() and let sas_ata_task_done() disposition the
qc.  Longer term we want to audit non-essential calls to
sas_task_abort().

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:21:24 -05:00
Dan Williams b50102d3e9 [SCSI] isci: atapi support
Based on original implementation from Jiangbi Liu and Maciej Trela.

ATAPI transfers happen in two-to-three stages.  The two stage atapi
commands are those that include a dma data transfer.  The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration.  The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.

stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb.  Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).

stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.

stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.

To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO).  This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).

If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition.  However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response.  In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.

Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:20:03 -05:00
Jeff Skirvin 983d3fdd33 [SCSI] isci: fix missed unlock in apc_agent_timeout()
Needed to jump to scic_lock unlock.

Also spotted by coccicheck.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:08:00 -05:00
Dan Williams 54b5e3a4bf [SCSI] isci: fix support for large smp requests
Kill the local smp response buffer.

Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes).  The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.

Cc: <stable@kernel.org>
Reported-by: Derick Marks <derick.w.marks@intel.com>
Tested-by: Derick Marks <derick.w.marks@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 13:07:17 -05:00
Dan Williams ad4f4c1de8 [SCSI] isci: initial sgpio write support
Basic support to initialize the gpio unit, accept an incomming
SAS_GPIO_REG_TX_GP bitstream, and translate it to the ODx.n fields in
the hardware registers.  If register indexes outside the supported range
are specified in the SMP frame we simply accept the write and return how
many registers (SFF-8485) were written (libsas reports this as residue
in the request).

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-22 15:01:56 +04:00
Dan Williams 13257cfbc5 [SCSI] isci: fix sgpio register definitions
output_data_select registers are off by one u32

delete the macros we will never use.

Reported-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-09-22 15:00:56 +04:00
Jiri Kosina e060c38434 Merge branch 'master' into for-next
Fast-forward merge with Linus to be able to merge patches
based on more recent version of the tree.
2011-09-15 15:08:18 +02:00
Justin P. Mattock 699324871f treewide: remove extra semicolons from various parts of the kernel
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2011-09-15 14:50:49 +02:00
Dan Williams 4fcf812ca3 [SCSI] libsas: export sas_alloc_task()
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.

Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-27 08:35:13 -06:00
Dan Williams 98e2a5a3a1 [SCSI] isci: add version number
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 20:06:14 -07:00
Dan Williams 77cd72a53f [SCSI] isci: fix event-get pointer increment
Hardware only increments the put pointer on event types >= 4.  Do not
increment the get pointer for event type 3.

Reported-by: Kapil Karkra <kapil.karkra@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 20:05:47 -07:00
Dan Williams 9b4be52899 [SCSI] isci: dynamic interrupt coalescing
Hardware allows both an outstanding number commands and a timeout value
(whichever occurs first) as a gate to the next interrupt generation.  This
scheme at completion time looks at the remaining number of outstanding tasks
and sets the timeout to maximize small transaction operation.  If transactions
are large (take more than a few 10s of microseconds to complete) then
performance is not interrupt processing bound, so the small timeouts this
scheme generates are overridden by the time it takes for a completion to
arrive.

Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 20:04:42 -07:00
Jeff Skirvin 39ea2c5b5f [SCSI] isci: Leave requests alone if already terminating.
Instead of immediately completing any request that has a second
termination call made on it, wait for the TC done/abort HW event.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 19:58:44 -07:00
Dave Jiang 3a7bda830f [SCSI] isci: Adding documentation to API change and fixup sysfs registration
Adding API update for adding isci_id entry scsi_host sysfs entry.
Also fixing up the sysfs registration to the scsi_host template

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 19:54:24 -07:00
Marcin Tomczak 985af6f70d [SCSI] isci: change sas phy timeouts from 54us to 59us
Need the following workaround in the driver for interoperability with
the older Intel SSD drives and any other SATA drive that may exhibit the
same behavior. This is a corner case where SCU speed is limited to
either 3G or 1.5G and the drive has a period of DC idle when it switches
speed during SATA speed negotiation. Workaround :change PHYTOV[31:24]
from 0x36 to 0x3B.

Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 19:52:14 -07:00
Dan Williams ee33e2b771 [SCSI] isci: fix 32-bit operation when CONFIG_HIGHMEM64G=n
The unsolicited frame control infrastructure requires a table of dma
addresses for the hardware to lookup the frame buffer location by an
index.  The hardware expects the elements of this table to be 64-bit
quantities, so we cannot reference these elements as dma_addr_t.  All
unsolicited frame protocols are affected, particularly SATA-PIO and SMP
which prevented direct-attached SATA drives and expander-attached drives
to not be discovered.

Cc: <stable@kernel.org>
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 19:50:27 -07:00
Dan Williams 1a87828447 [SCSI] isci: fix sata response handling
A bug (likely copy/paste) that has been carried from the original
implementation.  The unsolicited frame handling structure returns the
d2h fis in the isci_request.stp.rsp buffer.

Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-23 19:45:45 -07:00
James Bottomley a5ec7f86dc [SCSI] isci: fix checkpatch errors
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-03 14:26:24 -05:00
Jeff Skirvin bc6f387d31 isci: Device reset should request sas_phy_reset(phy, true)
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams a8a0a133b0 isci: pare back error messsages
The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams dc00c8b694 isci: cleanup silicon revision detection
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 4e4dca3de9 isci: merge scu_unsolicited_frame.h into unsolicited_frame_control.h
Does not need its own file.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 16ba77091b isci: merge sata.[ch] into request.c
Undo some needless separation.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 34a991587a isci: kill 'get/set' macros
Most of these simple dereference macros are longer than their open coded
equivalent.  Deleting enum sci_controller_mode is thrown in for good
measure.

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 89a7301f21 isci: retire scic_sds_ and scic_ prefixes
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_.  The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.

Also unwind the 'sds1' out of the parameter structs.

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams d9dcb4ba79 isci: unify isci_host and scic_sds_controller
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost).  Hmmm, we had two
'oem_parameters' instances, one was unused... nice.

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 78a6f06e0e isci: unify isci_remote_device and scic_sds_remote_device
Remove the distinction between these two implementations and unify on
isci_remote_device (local instances named idev).

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams ffe191c92f isci: unify isci_port and scic_sds_port
Remove the distinction between these two implementations and unify on
isci_port (local instances named iport).  The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.

Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00
Dan Williams 76802ce675 isci: fix scic_sds_remote_device_terminate_requests
Commit 0815632 "isci: unify remote_device stop_handlers" introduced the
possibility that not all requests get terminated if we reach the
request_count.  Now that we properly reference count devices we don't
need this self-defense and can do the straightforward scan of all active
requests.

Reported-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Acked-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2011-07-03 04:04:52 -07:00