* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix build of sh7750 base boards
sh: update INTC to clear IRQ sense valid flag
sh: Fix sh build failure when CONFIG_SFC=m
sh: fix MSIOF0 SPI on ecovec: it conflicts with VOU
sh: support XZ-compressed kernel.
sh: Fix up breakage from asm-generic/pgtable.h changes.
The EP93xx C and D GPIO ports are multiplexed with the Keypad Interface
peripheral. At power-up they default into non-GPIO mode with the Key
Matrix controller enabled so these ports are unusable for GPIO. Note
that the Keypad Interface peripheral is only available in the EP9307,
EP9312, and EP9315 processor variants.
The keypad support will clear the DeviceConfig bits appropriately to
enable the Keypad Interface when the driver is loaded. And, when the
driver is unloaded it will set the bits to return the ports to GPIO mode.
To make these ports available for GPIO after power-up on all EP93xx
processor variants, set the KEYS and GONK bits in the DeviceConfig
register.
Similarly, the E, G, and H ports are multiplexed with the IDE Interface
peripheral. At power-up these also default into non-GPIO mode. Note
that the IDE peripheral is only available in the EP9312 and EP9315
processor variants.
Since an IDE driver is not even available in mainline, set the EONIDE,
GONIDE, and HONIDE bits in the DeviceConfig register so that these
ports will be available for GPIO use after power-up.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Changing the virt_to_phys() argument to "const volatile void *" avoids
compiler warnings in some situations where this function is used.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the twd timer reload value is reprogrammed each time we
enter periodic mode. This ensures that the reload value is always
reset correctly.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the option text to those which appear on the front of the
appropriate board user guides. This gives consistent board naming, and
makes it obvious which option is for which platform.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As no one seems to really know which configuration options tie up with
which boards, I thought I'd do some investigation and try to work it
out. After discussion with some folk in linaro, I think I have this
nailed.
The names are updated to use the name on the front of the appropriate
board user guide for the various baseboards, which I've taken to be
the official name for each board.
I haven't significantly updated the descriptions for the tiles as that
is even less clear - as far as I can see on ARMs website, there is no
Cortex-A9 tile for Realview EB - only ARM11MPCore, ARM1156T2F-S,
ARM1176TZF-S and Cortex-R4F. So exactly what this 'Multicore Cortex-A9
Tile' is...
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two section mismatch warnings in the platform SMP bringup code for
Realview and Versatile Express:
WARNING: arch/arm/mach-realview/built-in.o(.text+0x8ac): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
WARNING: arch/arm/mach-vexpress/built-in.o(.text+0x7b4): Section mismatch in reference from the function write_pen_release() to the variable .cpuinit.data:pen_release
The function write_pen_release() references
the variable __cpuinitdata pen_release.
This is often because write_pen_release lacks a __cpuinitdata
annotation or the annotation of pen_release is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Function _sr_lookup, defined in the same file, returns ERR_PTR not NULL in
an error case.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f;
@@
f(...) { ... return ERR_PTR(...); }
@@
identifier r.f, fld;
expression x;
statement S1,S2;
@@
x = f(...)
... when != IS_ERR(x)
(
if (IS_ERR(x) ||...) S1 else S2
|
*x->fld
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In arch/x86/kernel/dumpstack_64.c::dump_trace() we have this code:
...
if (!stack) {
unsigned long dummy;
stack = &dummy;
if (task && task != current)
stack = (unsigned long *)task->thread.sp;
}
bp = stack_frame(task, regs);
/*
* Print function call entries in all stacks, starting at the
* current stack address. If the stacks consist of nested
* exceptions
*/
tinfo = task_thread_info(task);
for (;;) {
char *id;
unsigned long *estack_end;
estack_end = in_exception_stack(cpu, (unsigned long)stack,
&used, &id);
...
You'll notice that we assign to 'stack' the address of the variable
'dummy' which is only in-scope inside the 'if (!stack)'. So when we later
access stack (at the end of the above, and assuming we did not take the
'if (task && task != current)' branch) we'll be using the address of a
variable that is no longer in scope. I believe this patch is the proper
fix, but I freely admit that I'm not 100% certain.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
LKML-Reference: <alpine.LNX.2.00.1101242232590.10252@swampdragon.chaosbits.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: DMA: clear interrupt status correctly
OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration
arm: omap3: cm-t3517: minor comment fix
arm: omap3: cm-t3517: rtc fix
omap1: Fix sched_clock implementation when both MPU timer and 32K timer are used
omap1: Fix booting for 15xx and 730 with omap1_defconfig
omap1: Fix sched_clock for the MPU timer
OMAP: PRCM: remove duplicated headers
OMAP4: clockdomain: bypass unimplemented wake-up dependency functions on OMAP4
OMAP: counter_32k: init clocksource as part of machine timer init
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix time function double declaration with glibc
perf tools: Fix build by checking if extra warnings are supported
perf tools: Fix build when using gcc 3.4.6
perf tools: Add missing header, fixes build
perf tools: Fix 64 bit integer format strings
perf test: Fix build on older glibcs
perf: perf_event_exit_task_context: s/rcu_dereference/rcu_dereference_raw/
perf test: Use cpu_map->[cpu] when setting affinity
perf symbols: Fix annotation of thumb code
perf: Annotate cpuctx->ctx.mutex to avoid a lockdep splat
powerpc, perf: Fix frequency calculation for overflowing counters (FSL version)
perf: Fix perf_event_init_task()/perf_event_free_task() interaction
perf: Fix find_get_context() vs perf_event_exit_task() race
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix jump label with RO/NX module protection crash
x86, hotplug: Fix powersavings with offlined cores on AMD
x86, mcheck, therm_throt.c: Export symbol platform_thermal_notify to allow coretemp to handler intr
x86: Use asm-generic/cacheflush.h
x86: Update CPU cache attributes table descriptors
_CLK_SET_RATE does not only handle the cpu clock but also other
clocks, so do not hardcode the HW_CLKCTRL_CPU register.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
reg | (1 << clk->enable_shift) always evaluates to true. Switch it
to & which makes much more sense
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
If we use jump table in module init, there are marked
as removed in __jump_table section after init is done.
But we already applied ro permissions on the module, so
we can't modify a read only section (crash in
remove_jump_label_module_init).
Make the __jump_table section rw.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Siarhei Liakh <sliakh.lkml@gmail.com>
Cc: Xuxian Jiang <jiang@cs.ncsu.edu>
Cc: James Morris <jmorris@namei.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Cc: Kees Cook <kees.cook@canonical.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4D3C3F20.7030203@free.fr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
`debug=mem' on Amiga has been broken for a while.
early_param() processing is done very/too early, i.e. before
amiga_identify() / amiga_chip_init(), causing amiga_savekmsg_setup() not
to find any Chip RAM.
As we don't plan to free this memory anyway, just steal it from the initial
Chip RAM memory block instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It's a way too generic name for a global #define and conflicts with a variable
with the same name, causing build errors like:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c: In function ‘_si_clkctl_cc’:
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected identifier or ‘(’ before ‘volatile’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1364: error: expected ‘)’ before ‘(’ token
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1421: error: incompatible types in assignment
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1422: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1423: error: invalid operands to binary &
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1424: error: invalid operands to binary |
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: aggregate value used where an integer was expected
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1425: error: incompatible type for argument 4 of ‘bcmsdh_reg_write’
| drivers/staging/brcm80211/brcmfmac/../util/siutils.c:1428: error: invalid operands to binary &
| make[8]: *** [drivers/staging/brcm80211/brcmfmac/../util/siutils.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Some versions of gcc replace calls to strstr() with single-character
"needle" string parameters by calls to strchr() behind our back.
If strchr() is defined as an inline function, this causes linking errors
like
ERROR: "strchr" [drivers/target/target_core_mod.ko] undefined!
As m68k is the only architecture that has an inline strchr() and this
inline version is not an optimized asm version, uninline strchr() and use
the standard out-of-line C version in lib/string.c instead.
This also decreases the defconfig/allmodconfig kernel image sizes by a few
hundred bytes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
ea53069231 made a CPU use monitor/mwait
when offline. This is not the optimal choice for AMD wrt to powersavings
and we'd prefer our cores to halt (i.e. enter C1) instead. For this, the
same selection whether to use monitor/mwait has to be used as when we
select the idle routine for the machine.
With this patch, offlining cores 1-5 on a X6 machine allows core0 to
boost again.
[ hpa: putting this in urgent since it is a (power) regression fix ]
Reported-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@kernel.org # 37.x
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.hl>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1295534572-10730-1-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
After changing the p2m mapping to a tree by
commit 58e05027b5
xen: convert p2m to a 3 level tree
and trying to boot a DomU with 615MB of memory, the following crash was
observed in the dump:
kernel direct mapping tables up to 26f00000 @ 1ec4000-1fff000
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c0107397>] xen_set_pte+0x27/0x60
*pdpt = 0000000000000000 *pde = 0000000000000000
Adding further debug statements showed that when trying to set up
pfn=0x26700 the returned mapping was invalid.
pfn=0x266ff calling set_pte(0xc1fe77f8, 0x6b3003)
pfn=0x26700 calling set_pte(0xc1fe7800, 0x3)
Although the last_pfn obtained from the startup info is 0x26700, which
should in turn not be hit, the additional 8MB which are added as extra
memory normally seem to be ok. This lead to looking into the initial
p2m tree construction, which uses the smaller value and assuming that
there is other code handling the extra memory.
When the p2m tree is set up, the leaves are directly pointed to the
array which the domain builder set up. But if the mapping is not on a
boundary that fits into one p2m page, this will result in the last leaf
being only partially valid. And as the invalid entries are not
initialized in that case, things go badly wrong.
I am trying to fix that by checking whether the current leaf is a
complete map and if not, allocate a completely new page and copy only
the valid pointers there. This may not be the most efficient or elegant
solution, but at least it seems to allow me booting DomUs with memory
assignments all over the range.
BugLink: http://bugs.launchpad.net/bugs/686692
[v2: Redid a bit of commit wording and fixed a compile warning]
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In therm_throt.c, commit
9e76a97efd patch doesn't export
the symbol platform_thermal_notify.
Other drivers (e.g. drivers/hwmon/coretemp.c) can not find the
symbol platform_thermal_notify when defining threshould
interrupt handler.
Please apply this patch to allow threshold interrupt handler in
coretemp.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: R Durgadoss <durgadoss.r@intel.com>
Cc: khali@linux-fr.org <khali@linux-fr.org>
Cc: lm-sensors@lm-sensors.org <lm-sensors@lm-sensors.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
LKML-Reference: <20110121041239.GB26954@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The implementation of the cache flushing interfaces on the x86
is identical with the default implementation in asm-generic.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: arnd@arndb.de
LKML-Reference: <1295523136-4277-2-git-send-email-akinobu.mita@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Dike <jdike@addtoit.com>
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All architectures are finally converted. Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Use the generic irq Kconfig. Select GENERIC_HARDIRQS_NO_DEPRECATED as
we have converted all irq_chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chip to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Convert the irq chips to the new functions and use proper flow
handlers. handle_level_irq is appropriate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
The irq descriptors are already initialized by the generic
code. Remove the redundant init code and set the irq chip with the
proper accessor function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Use the generic irq Kconfig. Select GENERIC_HARDIRQS_NO_DEPRECATED as
we have converted all irq_chip functions. Fix the fallout in
show_interrupts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
Convert the irq chip functions and install handle_simple_irq for each
interrupt to get rid of __do_IRQ()
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
Convert the irq_chip functions and install handle_simple_irq for each
interrupt. This converts V10 to the flow handling and lets us remove
__do_IRQ().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
Use the wrapper around __do_IRQ() so we can convert V10 and V32
seperately.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mikael Starvik <starvik@axis.com>
Switch to the generic irq Kconfig. h8300 has all irq chips converted
to the new functions, so select the GENERIC_HARDIRQS_NO_DEPRECATED
switch as well. Fixup the resulting fallout in show_interrupts().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
__do_IRQ is deprecated so h8300 needs to be converted to proper flow
handling. The irq chip is simple and does not required any
mask/ack/eoi functions, so we can use handle_simple_irq.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
No functional change, just straight forward conversion.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Don't say that enable timed out when it was disable, and
show which IRQ had the problem.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upcoming servers will include a Broadcom NIC, add to the defconfig to
increase testing coverage and make sure mainline builds come up with
networking.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
- Enable 64kB pages so it gets some regular testing.
- The largest POWER7 has 1024 threads so bump NR_CPUS it to match.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
IRQSOFF_TRACER and STACK_TRACER force the kernel to be built with -pg
which is a substantial overhead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The dts-installed variable is initialised using a wildcard path that
will be expanded relative to the build directory. Use the existing
variable dtstree to generate an absolute wildcard path that will work
when building in a separate directory.
Reported-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Gerhard Pircher <gerhard_pircher@gmx.net> [against 2.6.32]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Decoding machine checks is CPU specific and so machine_check_generic doesn't
do the right thing on 64bit chips. Luckily we never call into this code
because we call ppc_md.machine_check_exception instead if available.
Since we check cur_cpu_spec->machine_check before calling it, we may as
well remove machine_check_generic from 64bit archs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The spec suggests we should first check the extended log flag before checking
the length field.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The FWNMI code uses a global buffer without any locks to read the RTAS error
information. If two CPUs take a machine check at once then we will corrupt
this buffer.
Since most FWNMI rtas messages are not of the extended type, we can create a
64bit percpu buffer and use it where possible. If we do receive an extended
RTAS log then we fall back to the old behaviour of using the global buffer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rework pseries machine check handler:
- If MSR_RI isn't set, we cannot recover even if the machine check was fully
recovered
- Rename nonfatal to recovered
- Handle RTAS_DISP_LIMITED_RECOVERY
- Use BUS_MCEERR_AR instead of BUS_ADRERR
- Don't check all the RTAS error log fields when receiving a synchronous
machine check. Recent versions of the pseries firmware do not fill them
in during a machine check and instead send a follow up error log with
the detailed information. If we see a synchronous machine check, and we
came from userspace then kill the task.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a machine check comes from userspace we send a SIGBUS to the task and
fail to printk anything.
If we are taking machine checks due to bad hardware we want to know about
it right away. Furthermore if we don't complain loudly then it will look
a lot like a bug in the userspace application, potentially causing a lot
of confusion.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are calling debugger_fault_handler twice in machine_check_exception.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Newer versions of the System p firwmare send a partial RTAS error log in the
machine check handler with a more detailed response appearing sometime later
via check event.
This means at machine check time we do not have enough information to
ascertain exactly what went on. Furthermore, I have found the RTAS error
logs in the machine check handler contain no useful information, so halting on
them makes little sense. If we want to halt it would make more sense to do
it following the error log received sometime later via check event.
In light of this, never halt the error log in the pseries machine
check handler.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should never force MSR_RI on. If we take a machine check with MSR_RI off
then we have no chance of recovering safely.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We were printing 64 bits of DSISR in show_regs even though it is 32 bit.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We should disable ftrace during kexec, some of the tracers are very invasive
and we do not want them going off while doing the low level work of swapping
one kernel out for another. This mirrors what we do on x86.
Even though we cannot return from a kexec on powerpc (since we do not implement
CONFIG_KEXEC_JUMP), add the restore code in case we do one day.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the crash handler hooks to run the SPU stop code, just like we do for
ehea and cell RAS code.
While I'm here I noticed "CPUSs reliabally"
so fix the spelling MISTAKESs reliabally.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We check for a valid handler before calling ppc_md.machine_kexec_prepare
so we can just remove these empty handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's no need to initialise ppc_md.machine_kexec and
ppc_md.machine_kexec_prepare to the default handlers.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_crash_shutdown, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_kexec, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
No one uses ppc_md.machine_kexec_cleanup, so remove it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move all the kexec handlers together.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With cmwq, there's no reason to use a separate workqueue in
cpufreq_spudemand. Use system_wq instead. The work items are already
sync canceled on stop, so it's already guaranteed that no work is
running when spu_gov_exit() is entered.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simplify read file operation for /proc/powerpc/rtas/* interface
by using simple_read_from_buffer.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Simplify several write fileoperations for spufs by using
simple_write_to_buffer().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
32-bit variant of the previous patch for 64-bit:
<<
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack....
>>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When an interrupt occurs in userspace, we can call trace_hardirqs_on/off()
With one level stack. But if we have irqsoff tracing enabled,
it checks both CALLER_ADDR0 and CALLER_ADDR1. The second call
goes two stack frames up. If this is from user space, then there may
not exist a second stack.
Add a second stack when calling trace_hardirqs_on/off() otherwise
the following oops might occur:
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 PA Semi PWRficient
last sysfs file: /sys/block/sda/size
Modules linked in: ohci_hcd ehci_hcd usbcore
NIP: c0000000000e1c00 LR: c0000000000034d4 CTR: 000000011012c440
REGS: c00000003e2f3af0 TRAP: 0300 Not tainted (2.6.37-rc6+)
MSR: 9000000000001032 <ME,IR,DR> CR: 48044444 XER: 20000000
DAR: 00000001ffb9db50, DSISR: 0000000040000000
TASK = c00000003e1a00a0[2088] 'emacs' THREAD: c00000003e2f0000 CPU: 1
GPR00: 0000000000000001 c00000003e2f3d70 c00000000084e0d0 c0000000008816e8
GPR04: 000000001034c678 000000001032e8f9 0000000010336540 0000000040020000
GPR08: 0000000040020000 00000001ffb9db40 c00000003e2f3e30 0000000060000000
GPR12: 100000000000f032 c00000000fff0280 000000001032e8c9 0000000000000008
GPR16: 00000000105be9c0 00000000105be950 00000000105be9b0 00000000105be950
GPR20: 00000000ffb9dc50 00000000ffb9dbf0 00000000102f0000 00000000102f0000
GPR24: 00000000102e0000 00000000102f0000 0000000010336540 c0000000009ded38
GPR28: 00000000102e0000 c0000000000034d4 c0000000007ccb10 c00000003e2f3d70
NIP [c0000000000e1c00] .trace_hardirqs_off+0xb0/0x1d0
LR [c0000000000034d4] decrementer_common+0xd4/0x100
Call Trace:
[c00000003e2f3d70] [c00000003e2f3e30] 0xc00000003e2f3e30 (unreliable)
[c00000003e2f3e30] [c0000000000034d4] decrementer_common+0xd4/0x100
Instruction dump:
81690000 7f8b0000 419e0018 f84a0028 60000000 60000000 60000000 e95f0000
80030000 e92a0000 eb6301f8 2f800000 <eb890010> 41fe00dc a06d000a eb1e8050
---[ end trace 4ec7fd2be9240928 ]---
Reported-by: Joerg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When we create an alternative feature section, the else case must be the
same size or smaller than the body. This is because when we patch the
else case in we just overwrite the body, so there must be room.
Up to now we just did this by inspection, but it's quite easy to enforce
it in the assembler, so we should.
The only change is to add the ifgt block, but that effects the alignment
of the tabs and so the whole macro is modified.
Also add a test, but #if 0 it because we don't want to break the build.
Anyone who's modifying the feature macros should enable the test.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
smp: Allow on_each_cpu() to be called while early_boot_irqs_disabled status to init/main.c
lockdep: Move early boot local IRQ enable/disable status to init/main.c
* akpm:
kernel/smp.c: consolidate writes in smp_call_function_interrupt()
kernel/smp.c: fix smp_call_function_many() SMP race
memcg: correctly order reading PCG_USED and pc->mem_cgroup
backlight: fix 88pm860x_bl macro collision
drivers/leds/ledtrig-gpio.c: make output match input, tighten input checking
MAINTAINERS: update Atmel AT91 entry
mm: fix truncate_setsize() comment
memcg: fix rmdir, force_empty with THP
memcg: fix LRU accounting with THP
memcg: fix USED bit handling at uncharge in THP
memcg: modify accounting function for supporting THP better
fs/direct-io.c: don't try to allocate more than BIO_MAX_PAGES in a bio
mm: compaction: prevent division-by-zero during user-requested compaction
mm/vmscan.c: remove duplicate include of compaction.h
memblock: fix memblock_is_region_memory()
thp: keep highpte mapped until it is no longer needed
kconfig: rename CONFIG_EMBEDDED to CONFIG_EXPERT
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: remove virtio-pci root device
LGUEST_GUEST: fix unmet direct dependencies (VIRTUALIZATION && VIRTIO)
lguest: compile fixes
lguest: Use this_cpu_ops
lguest: document --rng in example Launcher
lguest: example launcher to use guard pages, drop PROT_EXEC, fix limit logic
lguest: --username and --chroot options
Fix sparse warning for non-ANSI function declaration:
arch/x86/xen/irq.c:129:30: warning: non-ANSI function declaration of function 'xen_init_irq_ops'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Add platform data for MIPI-DSI and LCDC on the AG5EVM
board. The sh73a0 clkdev bindings are also updated.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PLL1 and PLL2 in the sh73a0 CPGA has a CFG bit that
must be taken into account to correctly calculate the
frequency.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
During early boot, local IRQ is disabled until IRQ subsystem is
properly initialized. During this time, no one should enable
local IRQ and some operations which usually are not allowed with
IRQ disabled, e.g. operations which might sleep or require
communications with other processors, are allowed.
lockdep tracked this with early_boot_irqs_off/on() callbacks.
As other subsystems need this information too, move it to
init/main.c and make it generally available. While at it,
toggle the boolean to early_boot_irqs_disabled instead of
enabled so that it can be initialized with %false and %true
indicates the exceptional condition.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20110120110635.GB6036@htj.dyndns.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update to latest definitions in:
http://www.intel.com/Assets/PDF/appnote/241618.pdf
[ Note, this update of the doc has removed some old values which
we have listed. I think until we have clarification that they
were never used in production, they should be left there. ]
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
LKML-Reference: <20110120012055.GA15985@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Honor the kconfig menu hierarchy to remove kconfig dependency warnings:
VIRTIO and VIRTIO_RING are subordinate to VIRTUALIZATION.
warning: (LGUEST_GUEST) selects VIRTIO which has unmet direct dependencies (VIRTUALIZATION)
warning: (LGUEST_GUEST && VIRTIO_PCI && VIRTIO_BALLOON) selects VIRTIO_RING which has unmet direct dependencies (VIRTUALIZATION && VIRTIO)
Reported-by: Toralf F_rster <toralf.foerster@gmx.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
arch/x86/lguest/boot.c: In function ‘lguest_init_IRQ’:
arch/x86/lguest/boot.c:824: error: macro "__this_cpu_write" requires 2 arguments, but only 1 given
arch/x86/lguest/boot.c:824: error: ‘__this_cpu_write’ undeclared (first use in this function)
arch/x86/lguest/boot.c:824: error: (Each undeclared identifier is reported only once
arch/x86/lguest/boot.c:824: error: for each function it appears in.)
drivers/lguest/x86/core.c: In function ‘copy_in_guest_info’:
drivers/lguest/x86/core.c:94: error: lvalue required as left operand of assignment
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When clearing the DMA channel, clear all status bits.
When handling a DMA interrupt, clear only the interrupt
status bits that have been read and are passed to the
channel's interrupt handler, not every status bit.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio7 on the tps65930 is used as an output on the devkit8000 and
gpio1 is not connected. Remove gpio7 and change gpio1 to pulldown
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When fixing the frequency calculations for perf on powerpc I
forgot to fix the FSL version.
If we dont set event->hw.last_period the frequency to period
calculations in perf go haywire and we continually
throttle/unthrottle the PMU.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110118214404.2f42e634@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Earlier patches select HAVE_SCHED_CLOCK for omaps. To have working sched_clock
also for MPU timer, we need to implement it in a way where the right one gets
selected during the runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit a4f740cf, "of/flattree: Add of_flat_dt_match() helper function"
introduced build failures in arch/powerpc/platform/83xx by mistyping
'static' as 'struct' in the compatible string list, and omitting a few
semicolons. This patch fixes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In order to be able to suppress the use of SRAT tables that
32-bit Linux can't deal with (in one case known to lead to a
non-bootable system, unless disabling ACPI altogether), move the
"numa=" option handling to common code.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Renninger <trenn@suse.de>
LKML-Reference: <4D36B581020000780002D0FF@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 86b1e8dd83 ("x86: Make relocatable kernel work with
new binutils").
Markus Trippelsdorf reported a boot failure caused by this patch.
The real solution to the original patch will likely involve an
arch-generic solution to define an overlaid jiffies_64 and jiffies
variables.
Until that's done and tested on all architectures revert this commit to
solve the regression.
Reported-and-bisected-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Lu, Hongjiu" <hongjiu.lu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>,
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4D36A759.60704@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CONFIG_SFC=m uses topology_core_cpumask() which, for sh, expects
cpu_core_map to be exported. It is not. This patch exports the needed
symbol.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* Pins 2 and 4 of switch 33 are documented as don't care on the PCB,
my testing seems to confirm this.
* I have been unable to do anything sensible with S1 set to on.
Am I missing something with regards to MMC1?
* Clarify which driver is needed for each switch setting.
* Should the AP4 board code be updated to allow the
SHDI driver to access SHDI1 as the mackerel code does?
Signed-off-by: Simon Horman <horms@verge.net.au>
Acked-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Clear irqstack thread_info
x86: Make relocatable kernel work with new binutils
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Malta: enable Cirrus FB console
MIPS: add CONFIG_VIRTUALIZATION for virtio support
MIPS: Implement __read_mostly
MIPS: ath79: add common WMAC device for AR913X based boards
MIPS: ath79: Add initial support for the Atheros AP81 reference board
MIPS: ath79: add common SPI controller device
SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
MIPS: ath79: add common GPIO buttons device
MIPS: ath79: add common watchdog device
MIPS: ath79: add common GPIO LEDs device
MIPS: ath79: add initial support for the Atheros PB44 reference board
MIPS: ath79: utilize the MIPS multi-machine support
MIPS: ath79: add GPIOLIB support
MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
MIPS: jump label: Add MIPS support.
MIPS: Use WARN() in uasm for better diagnostics.
MIPS: Optimize TLB handlers for Octeon CPUs
MIPS: Add LDX and LWX instructions to uasm.
MIPS: Use BBIT instructions in TLB handlers
MIPS: Declare uasm bbit0 and bbit1 functions.
...
A few headers are included twice, remove them.
Found the following errors using make includecheck:
arch/arm/mach-omap2/clock44xx_data.c: prm44xx.h is
included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm1_44xx.h
is included more than once.
arch/arm/mach-omap2/clockdomains44xx_data.c: cm2_44xx.h
is included more than once.
arch/arm/mach-omap2/powerdomain2xxx_3xxx.c: prm-regbits-34xx.h
is included more than once.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[paul@pwsan.com: dropped lists from patch cc:s; tweaked subject line]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 56a6a19dff ("omap2plus: prm:
Trvial build break fix for undefined reference to
'omap2_prm_read_mod_reg'") generates a lot of warnings on boot since
clockdomain functions that manipulate wake-up dependencies are not
implemented yet on OMAP4 for 2.6.38. This patch bypasses the OMAP2/3
functions on OMAP4, which in turn avoids the warnings when the
functions would attempt to call the underlying OMAP2/3 PRCM functions.
A one-line warning is still logged from the clockdomain code that the
OMAP4 wake-up dependency code is not yet implemented.
A clockdomain wake-up and sleep dependency implementation for OMAP4
from Rajendra should be possible to merge during the 2.6.39 merge
window:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg41748.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg42222.html
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit dc548fbbd2 ("ARM: omap: convert
sched_clock() to use new infrastructure"), OMAPs that use the 32KiHz
"synchronization timer" as their clocksource crash during boot:
[ 0.000000] OMAP clockevent source: GPTIMER1 at 32768 Hz
[ 0.000000] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 0.000000] pgd = c0004000
[ 0.000000] [00000000] *pgd=00000000
[ 0.000000] Internal error: Oops: 80000005 [#1] SMP
[ 0.000000] last sysfs file:
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Tainted: G W (2.6.37-07734-g2467802 #7)
[ 0.000000] PC is at 0x0
[ 0.000000] LR is at sched_clock_poll+0x2c/0x3c
[ 0.000000] pc : [<00000000>] lr : [<c0060b74>] psr: 600001d3
[ 0.000000] sp : c058bfd0 ip : c058a000 fp : 00000000
[ 0.000000] r10: 00000000 r9 : 411fc092 r8 : 800330c8
[ 0.000000] r7 : c05a08e0 r6 : c0034c48 r5 : c05ffc40 r4 : c0034c4c
[ 0.000000] r3 : c05ffe6c r2 : c05a0bc0 r1 : c059f098 r0 : 00000000
[ 0.000000] Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 0.000000] Control: 10c53c7f Table: 8000404a DAC: 00000017
This is due to the recent ARM init_sched_clock() changes and the late
initialization of the counter_32k clock source. More information here:
http://marc.info/?l=linux-omap&m=129513468605208&w=2
Fix by initializing the counter_32k clocksource during the machine timer
initialization.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
While most users of a physical Malta board are using the serial port
as the console, a lot of QEMU users would prefer to interact with a
graphical console. Enable the Cirrus FB support in the Malta default
configuration to make that possible. Note that the default console will
still be the serial port, users have to pass "console=tty0" to the
kernel to use the Cirrus FB.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2001/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CONFIG_VIRTUALIZATION to the MIPS architecture and include the
the virtio code there. Used to enable the virtio drivers under QEMU.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2002/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just do what everyone else is doing by placing __read_mostly things in
the .data.read_mostly section.
mips_io_port_base can not be read-only (const) and writable
(__read_mostly) at the same time. One of them has to go, so I chose
to eliminate the __read_mostly. It will still get stuck in a portion
of memory that is not adjacent to things that are written, and thus
not be on a dirty cache line, for whatever that is worth.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1702/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add common platform_device and helper code to make the registration
of the built-in wireless MAC easier on the Atheros AR9130/AR9132
based boards. Also register the WMAC device on the AR81 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>,
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several boards are using the built-in SPI controller of the
AR71XX/AR724X/AR913X SoCs. This patch adds common platform_device
and helper code to register it. Additionally, the patch registers
the SPI bus on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1956/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Almost all boards have one or more push buttons connected to GPIO lines.
This patch adds common code to register a platform_device for them.
The patch also adds support for the buttons on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1954/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All supported SoCs have a built-in hardware watchdog driver. This patch
registers a platform_device for that to make it usable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1955/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Almost all boards have one or more LEDs connected to GPIO lines. This
patch adds common code to register a platform_device for them.
The patch also adds support for the LEDs on the PB44 board.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1953/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds initial support for various Atheros SoCs based on the
MIPS 24Kc core. The following models are supported at the moment:
- AR7130
- AR7141
- AR7161
- AR9130
- AR9132
- AR7240
- AR7241
- AR7242
The current patch contains minimal support only, but the resulting
kernel can boot into user-space with using of an initramfs image on
various boards which are using these SoCs. Support for more built-in
devices and individual boards will be implemented in further patches.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In order not to be left behind, we add jump label support for MIPS.
Tested on 64-bit big endian (Octeon), and 32-bit little endian
(malta/qemu).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Jason Baron <jbaron@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/1923/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On the off chance that uasm ever warns about overflow, there is no way
to know what the offending instruction is.
Change the printks to WARNs, so we can get a nice stack trace. It has
the added benefit of being much more noticeable than the short single
line warning message, so is less likely to be ignored.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1905/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds
Hartley Sweeten
Catalin Marinas
Russell King
Pawel Moll
Nobuhiro Iwamatsu
Julia Lawall
Jesper Juhl
Fabio Estevam
Fabio Estevam
Sascha Hauer
matthieu castet
Geert Uytterhoeven
Borislav Petkov
Stefan Bader
Fenghua Yu
Akinobu Mita
Thomas Gleixner
Rakesh Iyer
Scott Wood
Nishanth Aravamudan
Anton Blanchard
Ben Hutchings
Tejun Heo
Steven Rostedt
Michael Ellerman
David Rientjes
Benjamin Herrenschmidt
Randy Dunlap
Magnus Damm
Dave Jones
Rusty Russell
Christoph Lameter
Adrian Hunter
Daniel Morsing
Igor Grinberg
Tony Lindgren
Grant Likely
Jan Beulich
Ingo Molnar
Aurelien Jarno
Simon Horman
Felipe Balbi
Paul Walmsley
David Daney
Gabor Juhos