The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.
So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.
Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff76834
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.
The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.
This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit 43fff76834 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
with:
pm_request_resume();
Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.
This results in the following happening:
1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
as no one has been calling pm_runtime_mark_last_busy(), the device was
resumed during those 5 seconds, so all the pm_request_resume() calls
while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
be read by the host the IRQ line is *already* / still logically high
when we autosuspend and since we use an edge triggered IRQ, the IRQ
will never trigger, causing the device to get stuck in suspend
Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Redpine bluetooth driver is a thin driver which depends on
'rsi_91x' driver for transmitting and receiving packets
to/from device. It creates hci interface when attach() is
called from 'rsi_91x' module.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.
Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c6 ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.
So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.
Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA ...")
Cc: stable@vger.kernel.org
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kevin Fenzi <kevin@scrye.com>
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.
Fixes: 3e81a4ca51 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-02-15
Here's the first bluetooth-next pull request targetting the 4.17 kernel
release.
- Fixes & cleanups to Atheros and Marvell drivers
- Support for two new Realtek controllers
- Support for new Intel Bluetooth controller
- Fix for supporting multiple slave-role Bluetooth LE connections
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Bluetooth parts of RTL8723D and RTL8723B share the same lmp
subversion, thus we need to check both lmp subversion and hci revision
to distinguish the two. The same situation is true for RTL8821A and
RTL8821C. Accordingly, the selection code is revised.
To improve maintainability, a new id_table struct is defined, and an
array of such structs is constructed. Adding a new device can thus be
as simple as adding another value to the table.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Asus Z370-I contains a Realtek RTL8822BE device with an associated
BT chip using a USB ID of 0b05:185c. This device is added to the driver.
Signed-off-by: Hon Weng Chong <honwchong@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
download_firmware() is never called from atomic context.
It is only called by ll_setup() that is called only via function pointer
"->setup" used in hci_uart_setup() in drivers/bluetooth/hci_serdev.c and
drivers/bluetooth/hci_ldisc.c. hci_uart_setup() is called only
via function pointer "->setup" used in hci_dev_do_open()
in net/bluetooth/hci_core.c.
All of the above functions do not enter atomic context.
Besides, ll_setup() calls msleep() and hci_dev_do_open calls mutex_lock().
So it indicates that all the above functions call functions that can sleep.
Despite never getting called from atomic context, download_firmware()
calls mdelay() for busy wait.
That is not necessary and can be replaced with msleep to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After checking all possible call chains to btmrvl_send_sync_cmd(),
my tool finds that this function is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
And it calls wait_event_interruptible_timeout() after bt_skb_alloc(),
so it indicates that btmrvl_send_sync_cmd()
can call function which can sleep.
Thus GFP_ATOMIC is not necessary, and it can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ath_wakeup_ar3k() is never called from atomic context.
It is only called by ath_hci_uart_work() that is only called in
ath_open() via INIT_WORK().
All of the above functions do not enter atomic context along the way.
Despite never getting called from atomic context, ath_wakeup_ar3k() calls
mdelay() for busy wait.
That is not necessary and can be replaced with msleep to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixed warning:
WARNING: Prefer using '"%s...", __func__' to using 'ath3k_disconnect', this function's name, in a string
#568: FILE: drivers/bluetooth/ath3k.c:568:
+ BT_DBG("ath3k_disconnect intf %p", intf);
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Do not need to initialize variables, because further on the code they
fall into the snprintf.
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replaced the numbers with a readable define.
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
The firmware download flow for RAM SKU is same for both USB and UART
and this patch creates a common function for both driver.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel_Read_Boot_Params command is used to read boot parameters
from the bootloader and this is Intel generic command used in USB
and UART drivers.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Each RAM SKU has a different boot parameter which is used in
HCI_Intel_Reset command after downloading the firmware.
The boot parameter is embedded in the firmware data and to support
multiple SKUs, driver reads the boot parameter while downloading
the firmware instead of using static values per SKU.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel_Reset command is used to reset the device after downloading
the firmware and this is Intel generic command used in both USB and
UART.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The format of Intel Bluetooth firmware for bootloader product is
ibt-<hw_variant>-<device_revision_id>.sfi and .ddc.
But for the 9x60 SKU, there are three variants of FW, which cannot be
differenticate just with hw_variant and device_revision_id.
So, to pick the appropriate FW file for 9x60 SKU, three fields,
hw_variant, hw_revision, and fw_revision, needs to be used rather than
hw_variant and device_revision_id.
Format will be like this:
ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi and .ddc
Signed-off-by: Tedd Ho-Jeong An <tedd.an@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 8bfa7e1e03 ("Bluetooth: hci_bcm: Handle errors properly")
introduced error checking for the bcm_gpio_set_power() call in bcm_open()
but the error-path it introduces unsets dev->hu, which is correct for
platform_device instantiated bcm_dev-s but not for serdev instantiated
devs. For serdev instantiated devs serdev_device_close() should be called
instead (and dev->hu should be left set).
Cc: Lukas Wunner <lukas@wunner.de>
Fixes: 8bfa7e1e03 ("Bluetooth: hci_bcm: Handle errors properly")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the device ID for the bluetooth chip used in the
AMPAK AP6212 WiFi+Bluetooth module. The AP6212 is used on several
BananaPi boards, e.g. M2-Ultra.
The AP6212 is a combo module, where the WiFi chip is identified as
BCM43430A0 whereas the Bluetooth chip identifies itself as 4343A0. Note,
the missing '0' before the 'A0'.
The AP6212 needs a firmware blob. Loading the provided firmware file
from the BananaPi vendor, the adapter name is printed as
'BCM4343A0 26MHz AP6212_CL1-0061':
'''
hci0: Type: Primary Bus: UART
BD Address: 43:43:A0:12:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING
RX bytes:3076 acl:0 sco:0 events:278 errors:0
TX bytes:39726 acl:0 sco:0 commands:279 errors:0
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: SLAVE ACCEPT
Name: 'BCM4343A0 26MHz AP6212_CL1-0061'
Class: 0x000000
Service Classes: Unspecified
Device Class: Miscellaneous,
HCI Version: 4.1 (0x7) Revision: 0xf2
LMP Version: 4.1 (0x7) Subversion: 0x2122
Manufacturer: Broadcom Corporation (15)
'''
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the documentation for Laird SD40 radio modules (which use
the BCM4329 chipset), the order of the Enable_BREAK_To_Host and
Pulsed_HOST_WAKE parameters in the sleep mode struct is reversed
vis-à-vis our struct declaration. See page 46 of this PDF:
http://cdn.lairdtech.com/home/brandworld/files/Application%20Note%20-%2040%20Series%20Bluetooth.pdf
The documentation is dated Oct 2015, so fairly recent, making it appear
more likely that the documentation is correct and our code is wrong.
Amend our code to be in congruence with the documentation.
Cc: Sue White <sue.white@lairdtech.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver calls mdelay(15) in the ->suspend, ->resume, ->runtime_suspend
and ->runtime_resume hook, however spinning for such a long period of
time is discouraged as per Documentation/timers/timers-howto.txt.
The use of mdelay() seems unnecessary, it is allowed to sleep in the
system sleep and runtime PM hooks (with the exception of ->suspend_noirq
and ->resume_noirq) and the driver itself also does not rely on a
non-sleeping ->runtime_resume as the only place where a synchronous
resume is performed, in bcm_dequeue(), is called from a work item in
hci_ldisc.c and hci_serdev.c.
So replace the mdelay(15) with msleep(15).
Note that the delay is inserted after asserting or deasserting the
device wake pin, but in bcm_gpio_set_power() that pin is asserted or
deasserted *without* observing a delay. It is thus unclear if the delay
is necessary at all. It is likewise unclear why it is exactly 15 ms,
the commit introducing it, 118612fb91 ("Bluetooth: hci_bcm: Add
suspend/resume PM functions"), does not provide a rationale.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The host wake IRQ is optional, but if none is found, "BCM irq: -22" is
logged which may irritate users. This is really a debug message, so use
dev_dbg() instead of dev_info(). If users are interested in the IRQ,
they can always consult /proc/interrupts.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable Bluetooth on the following Macs which provide custom ACPI methods
to toggle the GPIOs for device wake and shutdown instead of accessing
the pins directly:
MacBook8,1 2015 12"
MacBook9,1 2016 12"
MacBook10,1 2017 12"
MacBookPro13,1 2016 13"
MacBookPro13,2 2016 13" with Touch Bar
MacBookPro13,3 2016 15" with Touch Bar
MacBookPro14,1 2017 13"
MacBookPro14,2 2017 13" with Touch Bar
MacBookPro14,3 2017 15" with Touch Bar
On the MacBook8,1 Bluetooth is muxed with a second device (a debug port
on the SSD) under the control of PCH GPIO 36. Because serdev cannot
deal with multiple slaves yet, it is currently necessary to patch the
DSDT and remove the SSDC device.
The custom ACPI methods are called:
BTLP (Low Power) takes one argument, toggles device wake GPIO
BTPU (Power Up) tells SMC to drive shutdown GPIO high
BTPD (Power Down) tells SMC to drive shutdown GPIO low
BTRS (Reset) calls BTPD followed by BTPU
BTRB unknown, not present on all MacBooks
Search for the BTLP, BTPU and BTPD methods on ->probe and cache them in
struct bcm_device if the machine is a Mac.
Additionally, set the init_speed based on a custom device property
provided by Apple in lieu of _CRS resources. The Broadcom UART's speed
is fixed on Apple Macs: Any attempt to change it results in Bluetooth
status code 0x0c and bcm_set_baudrate() thus always returns -EBUSY.
By setting only the init_speed and leaving oper_speed at zero, we can
achieve that the host UART's speed is adjusted but the Broadcom UART's
speed is left as is.
The host wake pin goes into the SMC which handles it independently
of the OS, so there's no IRQ for it.
Thanks to Ronald Tschalär who did extensive debugging and testing of
this patch and contributed fixes.
ACPI snippet containing the custom methods and device properties
(taken from a MacBook8,1):
Method (BTLP, 1, Serialized)
{
If (LEqual (Arg0, 0x00))
{
Store (0x01, GD54) /* set PCH GPIO 54 direction to input */
}
If (LEqual (Arg0, 0x01))
{
Store (0x00, GD54) /* set PCH GPIO 54 direction to output */
Store (0x00, GP54) /* set PCH GPIO 54 value to low */
}
}
Method (BTPU, 0, Serialized)
{
Store (0x01, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTPD, 0, Serialized)
{
Store (0x00, \_SB.PCI0.LPCB.EC.BTPC)
Sleep (0x0A)
}
Method (BTRS, 0, Serialized)
{
BTPD ()
BTPU ()
}
Method (_DSM, 4, NotSerialized) // _DSM: Device-Specific Method
{
If (LEqual (Arg0, ToUUID ("a0b5b7c6-1318-441c-b0c9-fe695eaf949b")))
{
Store (Package (0x08)
{
"baud",
Buffer (0x08)
{ 0xC0, 0xC6, 0x2D, 0x00, 0x00, 0x00, 0x00, 0x00 },
"parity",
Buffer (0x08)
{ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"dataBits",
Buffer (0x08)
{ 0x08, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 },
"stopBits",
Buffer (0x08)
{ 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }
}, Local0)
DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0))
Return (Local0)
}
Return (0x00)
}
Link: https://github.com/Dunedan/mbp-2016-linux/issues/29
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Tested-by: Max Shavrick <mxms@me.com> [MacBook8,1]
Tested-by: Leif Liddy <leif.liddy@gmail.com> [MacBook9,1]
Tested-by: Daniel Roschka <danielroschka@phoenitydawn.de> [MacBookPro13,2]
Tested-by: Ronald Tschalär <ronald@innovation.ch> [MacBookPro13,3]
Tested-by: Peter Y. Chuang <peteryuchuang@gmail.com> [MacBookPro14,1]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A significant portion of this driver lacks error handling. As a first
step, add error paths to bcm_gpio_set_power(), bcm_open(), bcm_close(),
bcm_suspend_device(), bcm_resume_device(), bcm_resume(), bcm_probe() and
bcm_serdev_probe(). (I've also scrutinized bcm_suspend() but think it's
fine as is.)
Those are all the functions accessing the device wake and shutdown GPIO.
On Apple Macs the pins are accessed through ACPI methods, which may fail
for various reasons, hence proper error handling is necessary. Non-Macs
access the pins directly, which may fail as well but the GPIO core does
not yet pass back errors to consumers.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
MacBooks provides custom ACPI methods to toggle the GPIOs for device
wake and shutdown instead of accessing the pins directly. Prepare for
their support by adding callbacks to toggle the GPIOs, which on non-Macs
do nothing more but call gpiod_set_value().
No functional change intended.
Suggested-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If devm_request_irq() fails, the driver bails out of bcm_request_irq()
but continues to ->setup the device (because the IRQ is optional).
The driver subsequently calls devm_free_irq(), enable_irq_wake() and
disable_irq_wake() on the IRQ even though requesting it failed.
Avoid by invalidating the IRQ on request failure.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On ->setup, pm_runtime_enable() is only called if a valid IRQ was found,
but on ->close(), pm_runtime_disable() is called unconditionally.
Disablement of runtime PM is recorded in a counter, so every
pm_runtime_disable() needs to be balanced. Fix it.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reported-and-reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Upon ->close, the driver powers the Bluetooth controller down, deasserts
the device wake pin, updates the runtime PM status to "suspended" and
finally frees the IRQ.
Because the IRQ is freed last, a runtime resume can take place after
the controller was powered down. The impact is not grave, the worst
thing that can happen is that the device wake pin is reasserted (should
have no effect while the regulator is off) and that setting the runtime
PM status to "suspended" does not reflect reality.
Still, it's wrong, so free the IRQ first.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
pm_runtime_disable() and pm_runtime_set_suspended() are replaced with
empty inlines if CONFIG_PM is disabled, so there's no need to #ifdef
them.
device_init_wakeup() is likewise replaced with an inline, though it's
not empty, but it and devm_free_irq() can be made conditional on
IS_ENABLED(CONFIG_PM), which is preferable to #ifdef as per section 20
of Documentation/process/coding-style.rst.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ->close, ->suspend and ->resume hooks assume presence of a valid IRQ
if the device is wakeup capable. However it's entirely possible that
wakeup was enabled by some other entity besides this driver and in this
case the user will get a WARN splat if no valid IRQ was found. Avoid by
checking if the IRQ is valid, i.e. > 0.
Case in point: On recent MacBook Pros, the Bluetooth device lacks an
IRQ (because host wakeup is handled by the SMC, independently of the
operating system), but it does possess a _PRW method (which specifies
the SMC's GPE as wake event). The ACPI core therefore automatically
marks the physical Bluetooth device wakeup capable upon binding it to
its ACPI companion:
device_set_wakeup_capable+0x96/0xb0
acpi_bind_one+0x28a/0x310
acpi_platform_notify+0x20/0xa0
device_add+0x215/0x690
serdev_device_add+0x57/0xf0
acpi_serdev_add_device+0xc9/0x110
acpi_ns_walk_namespace+0x131/0x280
acpi_walk_namespace+0xf5/0x13d
serdev_controller_add+0x6f/0x110
serdev_tty_port_register+0x98/0xf0
tty_port_register_device_attr_serdev+0x3a/0x70
uart_add_one_port+0x268/0x500
serial8250_register_8250_port+0x32e/0x490
dw8250_probe+0x46c/0x720
platform_drv_probe+0x35/0x90
driver_probe_device+0x300/0x450
bus_for_each_drv+0x67/0xb0
__device_attach+0xde/0x160
bus_probe_device+0x9c/0xb0
device_add+0x448/0x690
platform_device_add+0x10e/0x260
mfd_add_device+0x392/0x4c0
mfd_add_devices+0xb1/0x110
intel_lpss_probe+0x2a9/0x610 [intel_lpss]
intel_lpss_pci_probe+0x7a/0xa8 [intel_lpss_pci]
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
[lukas: fix up ->suspend and ->resume as well, add commit message]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 0395ffc1ee ("Bluetooth: hci_bcm: Add PM for BCM devices")
amended this driver to request a shutdown and device wake GPIO on probe,
but mandated that only one of them need to be present:
/* Make sure at-least one of the GPIO is defined and that
* a name is specified for this instance
*/
if ((!dev->device_wakeup && !dev->shutdown) || !dev->name) {
dev_err(&pdev->dev, "invalid platform data\n");
return -EINVAL;
}
However the same commit added a call to bcm_gpio_set_power() to the
->probe hook, which unconditionally accesses *both* GPIOs. Luckily,
the resulting NULL pointer deref was never reported, suggesting there's
no machine where either GPIO is missing.
Commit 8a92056837 ("Bluetooth: hci_bcm: Add (runtime)pm support to the
serdev driver") removed the check whether at least one of the GPIOs is
present without specifying a reason.
Because commit 62aaefa7d0 ("Bluetooth: hci_bcm: improve use of gpios
API") refactored the driver to use devm_gpiod_get_optional() instead of
devm_gpiod_get(), one is now tempted to believe that the driver doesn't
require *any* of the two GPIOs.
Which is wrong, the driver still requires both GPIOs to avoid a NULL
pointer deref. To this end, establish the status quo ante and request
the GPIOs with devm_gpiod_get() again. Bail out of ->probe if either
of them is missing.
Oddly enough, whereas bcm_gpio_set_power() accesses the device wake pin
unconditionally, bcm_suspend_device() and bcm_resume_device() do check
for its presence before accessing it. Those checks are superfluous,
so remove them.
Cc: Frédéric Danis <frederic.danis.oss@gmail.com>
Cc: Loic Poulain <loic.poulain@linaro.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 7d06d5895c ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
removed the setting of the BTUSB_RESET_RESUME quirk for QCA Rome devices,
instead favoring adding USB_QUIRK_RESET_RESUME quirks in usb/core/quirks.c.
This was done because the DIY BTUSB_RESET_RESUME reset-resume handling
has several issues (see the original commit message). An added advantage
of moving over to the USB-core reset-resume handling is that it also
disables autosuspend for these devices, which is similarly broken on these.
But there are 2 issues with this approach:
1) It leaves the broken DIY BTUSB_RESET_RESUME code in place for Realtek
devices.
2) Sofar only 2 of the 10 QCA devices known to the btusb code have been
added to usb/core/quirks.c and if we fix the Realtek case the same way
we need to add an additional 14 entries. So in essence we need to
duplicate a large part of the usb_device_id table in btusb.c in
usb/core/quirks.c and manually keep them in sync.
This commit instead restores setting a reset-resume quirk for QCA devices
in the btusb.c code, avoiding the duplicate usb_device_id table problem.
This commit avoids the problems with the original DIY BTUSB_RESET_RESUME
code by simply setting the USB_QUIRK_RESET_RESUME quirk directly on the
usb_device.
This commit also moves the BTUSB_REALTEK case over to directly setting the
USB_QUIRK_RESET_RESUME on the usb_device and removes the now unused
BTUSB_RESET_RESUME code.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 7d06d5895c ("Revert "Bluetooth: btusb: fix QCA...suspend/resume"")
Cc: stable@vger.kernel.org
Cc: Leif Liddy <leif.linux@gmail.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Daniel Drake <drake@endlessm.com>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't populate the const read-only array 'param' on the stack but instead
make it static. Makes the object code smaller by nearly 20 bytes:
Before:
text data bss dec hex filename
11605 2629 64 14298 37da linux/drivers/bluetooth/btintel.o
After:
text data bss dec hex filename
11531 2685 64 14280 37c8 linux/drivers/bluetooth/btintel.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't populate the const read-only array 'req' on the stack but instead
make it static. Makes the object code smaller by over 40 bytes:
Before:
text data bss dec hex filename
8497 3408 128 12033 2f01 linux/drivers/bluetooth/bpa10x.o
After:
text data bss dec hex filename
8366 3496 128 11990 2ed6 linux/drivers/bluetooth/bpa10x.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 27378f4c1b ("Bluetooth: Avoid WARN splat due to missing
GPIOLIB") amended Kconfig to select GPIOLIB if BT_HCIUART_NOKIA,
BT_HCIUART_INTEL or BT_HCIUART_BCM is enabled since all three drivers
require it to function.
The diagnosis was correct but the treatment was not. As stated in
Documentation/gpio/consumer.txt:
Guidelines for GPIOs consumers
==============================
Drivers that can't work without standard GPIO calls should have
Kconfig entries that depend on GPIOLIB.
^^^^^^^^^
Fix it.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the hci support is built-in, but mvmem is a loadable module, we
get a link failure:
drivers/bluetooth/hci_ll.o: In function `hci_ti_probe':
hci_ll.c:(.text+0x226): undefined reference to `nvmem_cell_get'
hci_ll.c:(.text+0x238): undefined reference to `nvmem_cell_read'
hci_ll.c:(.text+0x244): undefined reference to `nvmem_cell_put'
This adds another Kconfig dependency to enforce valid configurations.
Fixes: 0e58d0cdb3 ("Bluetooth: hci_ll: Add optional nvmem BD address source")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
David S. Miller
Hans de Goede
Takashi Iwai
Prameela Rani Garnepudi
Kai-Heng Feng
Stefan Wahren
Linus Torvalds
Alex Lu
Larry Finger
Jia-Ju Bai
Maxim Zhukov
Tedd Ho-Jeong An
Tedd Ho-Jeong An
Jörg Krause
Lukas Wunner
Ronald Tschalär
Colin Ian King
Arnd Bergmann