Commit Graph

570 Commits

Author SHA1 Message Date
Denis Du b6c3bad1ba hdlc_ppp: carrier detect ok, don't turn off negotiation
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.

Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-26 14:38:12 -05:00
Linus Torvalds 168fe32a07 Merge branch 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull poll annotations from Al Viro:
 "This introduces a __bitwise type for POLL### bitmap, and propagates
  the annotations through the tree. Most of that stuff is as simple as
  'make ->poll() instances return __poll_t and do the same to local
  variables used to hold the future return value'.

  Some of the obvious brainos found in process are fixed (e.g. POLLIN
  misspelled as POLL_IN). At that point the amount of sparse warnings is
  low and most of them are for genuine bugs - e.g. ->poll() instance
  deciding to return -EINVAL instead of a bitmap. I hadn't touched those
  in this series - it's large enough as it is.

  Another problem it has caught was eventpoll() ABI mess; select.c and
  eventpoll.c assumed that corresponding POLL### and EPOLL### were
  equal. That's true for some, but not all of them - EPOLL### are
  arch-independent, but POLL### are not.

  The last commit in this series separates userland POLL### values from
  the (now arch-independent) kernel-side ones, converting between them
  in the few places where they are copied to/from userland. AFAICS, this
  is the least disruptive fix preserving poll(2) ABI and making epoll()
  work on all architectures.

  As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
  it will trigger only on what would've triggered EPOLLWRBAND on other
  architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
  at all on sparc. With this patch they should work consistently on all
  architectures"

* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
  make kernel-side POLL... arch-independent
  eventpoll: no need to mask the result of epi_item_poll() again
  eventpoll: constify struct epoll_event pointers
  debugging printk in sg_poll() uses %x to print POLL... bitmap
  annotate poll(2) guts
  9p: untangle ->poll() mess
  ->si_band gets POLL... bitmap stored into a user-visible long field
  ring_buffer_poll_wait() return value used as return value of ->poll()
  the rest of drivers/*: annotate ->poll() instances
  media: annotate ->poll() instances
  fs: annotate ->poll() instances
  ipc, kernel, mm: annotate ->poll() instances
  net: annotate ->poll() instances
  apparmor: annotate ->poll() instances
  tomoyo: annotate ->poll() instances
  sound: annotate ->poll() instances
  acpi: annotate ->poll() instances
  crypto: annotate ->poll() instances
  block: annotate ->poll() instances
  x86: annotate ->poll() instances
  ...
2018-01-30 17:58:07 -08:00
Linus Torvalds 96c22a49ac Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
    missed one spot. From Zhu Yanjun.

 2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.

 3) Fix checksum offloading in thunderx driver, from Sunil Goutham.

 4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.

 5) Fix use after free of packet headers in TIPC, from Jon Maloy.

 6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.

 7) Tunneling fixes in mlxsw driver, from Petr Machata.

 8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
    Maloney.

 9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
    Dumazet.

10) Fix regression in sch_sfq.c due to one of the timer_setup()
    conversions. From Paolo Abeni.

11) SCTP does list_for_each_entry() using wrong struct member, fix from
    Xin Long.

12) Don't use big endian netlink attribute read for
    IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
    Long.

13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
    adding filters there. From Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  ethernet: dwmac-stm32: Fix copyright
  net: via: via-rhine: use %p to format void * address instead of %x
  net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
  myri10ge: Update MAINTAINERS
  net: sched: cbq: create block for q->link.block
  atm: suni: remove extraneous space to fix indentation
  atm: lanai: use %p to format kernel addresses instead of %x
  VSOCK: Don't set sk_state to TCP_CLOSE before testing it
  atm: fore200e: use %pK to format kernel addresses instead of %x
  ambassador: fix incorrect indentation of assignment statement
  vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
  bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
  sctp: use right member as the param of list_for_each_entry
  sch_sfq: fix null pointer dereference at timer expiration
  cls_bpf: don't decrement net's refcount when offload fails
  net/packet: fix a race in packet_bind() and packet_notifier()
  packet: fix crash in fanout_demux_rollover()
  sctp: remove extern from stream sched
  sctp: force the params with right types for sctp csum apis
  sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
  ...
2017-11-29 13:10:25 -08:00
Al Viro afc9a42b74 the rest of drivers/*: annotate ->poll() instances
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-28 11:06:58 -05:00
Vasyl Gomonovych f95d5bf03b lmc: Use memdup_user() as a cleanup
Fix coccicheck warning which recommends to use memdup_user():
drivers/net/wan/lmc/lmc_main.c:497:27-34: WARNING opportunity for memdup_user
Generated by: scripts/coccinelle/memdup_user/memdup_user.cocci

Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-28 10:57:54 -05:00
Kees Cook e99e88a9d2 treewide: setup_timer() -> timer_setup()
This converts all remaining cases of the old setup_timer() API into using
timer_setup(), where the callback argument is the structure already
holding the struct timer_list. These should have no behavioral changes,
since they just change which pointer is passed into the callback with
the same available pointers after conversion. It handles the following
examples, in addition to some other variations.

Casting from unsigned long:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, ptr);

and forced object casts:

    void my_callback(struct something *ptr)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, (unsigned long)ptr);

become:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

Direct function assignments:

    void my_callback(unsigned long data)
    {
        struct something *ptr = (struct something *)data;
    ...
    }
    ...
    ptr->my_timer.function = my_callback;

have a temporary cast added, along with converting the args:

    void my_callback(struct timer_list *t)
    {
        struct something *ptr = from_timer(ptr, t, my_timer);
    ...
    }
    ...
    ptr->my_timer.function = (TIMER_FUNC_TYPE)my_callback;

And finally, callbacks without a data assignment:

    void my_callback(unsigned long data)
    {
    ...
    }
    ...
    setup_timer(&ptr->my_timer, my_callback, 0);

have their argument renamed to verify they're unused during conversion:

    void my_callback(struct timer_list *unused)
    {
    ...
    }
    ...
    timer_setup(&ptr->my_timer, my_callback, 0);

The conversion is done with the following Coccinelle script:

spatch --very-quiet --all-includes --include-headers \
	-I ./arch/x86/include -I ./arch/x86/include/generated \
	-I ./include -I ./arch/x86/include/uapi \
	-I ./arch/x86/include/generated/uapi -I ./include/uapi \
	-I ./include/generated/uapi --include ./include/linux/kconfig.h \
	--dir . \
	--cocci-file ~/src/data/timer_setup.cocci

@fix_address_of@
expression e;
@@

 setup_timer(
-&(e)
+&e
 , ...)

// Update any raw setup_timer() usages that have a NULL callback, but
// would otherwise match change_timer_function_usage, since the latter
// will update all function assignments done in the face of a NULL
// function initialization in setup_timer().
@change_timer_function_usage_NULL@
expression _E;
identifier _timer;
type _cast_data;
@@

(
-setup_timer(&_E->_timer, NULL, _E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E->_timer, NULL, (_cast_data)_E);
+timer_setup(&_E->_timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, &_E);
+timer_setup(&_E._timer, NULL, 0);
|
-setup_timer(&_E._timer, NULL, (_cast_data)&_E);
+timer_setup(&_E._timer, NULL, 0);
)

@change_timer_function_usage@
expression _E;
identifier _timer;
struct timer_list _stl;
identifier _callback;
type _cast_func, _cast_data;
@@

(
-setup_timer(&_E->_timer, _callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, &_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, _E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, &_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)_E);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, (_cast_func)&_callback, (_cast_data)&_E);
+timer_setup(&_E._timer, _callback, 0);
|
 _E->_timer@_stl.function = _callback;
|
 _E->_timer@_stl.function = &_callback;
|
 _E->_timer@_stl.function = (_cast_func)_callback;
|
 _E->_timer@_stl.function = (_cast_func)&_callback;
|
 _E._timer@_stl.function = _callback;
|
 _E._timer@_stl.function = &_callback;
|
 _E._timer@_stl.function = (_cast_func)_callback;
|
 _E._timer@_stl.function = (_cast_func)&_callback;
)

// callback(unsigned long arg)
@change_callback_handle_cast
 depends on change_timer_function_usage@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
identifier _handle;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
(
	... when != _origarg
	_handletype *_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(_handletype *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
|
	... when != _origarg
	_handletype *_handle;
	... when != _handle
	_handle =
-(void *)_origarg;
+from_timer(_handle, t, _timer);
	... when != _origarg
)
 }

// callback(unsigned long arg) without existing variable
@change_callback_handle_cast_no_arg
 depends on change_timer_function_usage &&
                     !change_callback_handle_cast@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _origtype;
identifier _origarg;
type _handletype;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *t
 )
 {
+	_handletype *_origarg = from_timer(_origarg, t, _timer);
+
	... when != _origarg
-	(_handletype *)_origarg
+	_origarg
	... when != _origarg
 }

// Avoid already converted callbacks.
@match_callback_converted
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
	    !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier t;
@@

 void _callback(struct timer_list *t)
 { ... }

// callback(struct something *handle)
@change_callback_handle_arg
 depends on change_timer_function_usage &&
	    !match_callback_converted &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
@@

 void _callback(
-_handletype *_handle
+struct timer_list *t
 )
 {
+	_handletype *_handle = from_timer(_handle, t, _timer);
	...
 }

// If change_callback_handle_arg ran on an empty function, remove
// the added handler.
@unchange_callback_handle_arg
 depends on change_timer_function_usage &&
	    change_callback_handle_arg@
identifier change_timer_function_usage._callback;
identifier change_timer_function_usage._timer;
type _handletype;
identifier _handle;
identifier t;
@@

 void _callback(struct timer_list *t)
 {
-	_handletype *_handle = from_timer(_handle, t, _timer);
 }

// We only want to refactor the setup_timer() data argument if we've found
// the matching callback. This undoes changes in change_timer_function_usage.
@unchange_timer_function_usage
 depends on change_timer_function_usage &&
            !change_callback_handle_cast &&
            !change_callback_handle_cast_no_arg &&
	    !change_callback_handle_arg@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type change_timer_function_usage._cast_data;
@@

(
-timer_setup(&_E->_timer, _callback, 0);
+setup_timer(&_E->_timer, _callback, (_cast_data)_E);
|
-timer_setup(&_E._timer, _callback, 0);
+setup_timer(&_E._timer, _callback, (_cast_data)&_E);
)

// If we fixed a callback from a .function assignment, fix the
// assignment cast now.
@change_timer_function_assignment
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression change_timer_function_usage._E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_func;
typedef TIMER_FUNC_TYPE;
@@

(
 _E->_timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E->_timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-&_callback;
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)_callback
+(TIMER_FUNC_TYPE)_callback
 ;
|
 _E._timer.function =
-(_cast_func)&_callback
+(TIMER_FUNC_TYPE)_callback
 ;
)

// Sometimes timer functions are called directly. Replace matched args.
@change_timer_function_calls
 depends on change_timer_function_usage &&
            (change_callback_handle_cast ||
             change_callback_handle_cast_no_arg ||
             change_callback_handle_arg)@
expression _E;
identifier change_timer_function_usage._timer;
identifier change_timer_function_usage._callback;
type _cast_data;
@@

 _callback(
(
-(_cast_data)_E
+&_E->_timer
|
-(_cast_data)&_E
+&_E._timer
|
-_E
+&_E->_timer
)
 )

// If a timer has been configured without a data argument, it can be
// converted without regard to the callback argument, since it is unused.
@match_timer_function_unused_data@
expression _E;
identifier _timer;
identifier _callback;
@@

(
-setup_timer(&_E->_timer, _callback, 0);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0L);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E->_timer, _callback, 0UL);
+timer_setup(&_E->_timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0L);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_E._timer, _callback, 0UL);
+timer_setup(&_E._timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0L);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(&_timer, _callback, 0UL);
+timer_setup(&_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0L);
+timer_setup(_timer, _callback, 0);
|
-setup_timer(_timer, _callback, 0UL);
+timer_setup(_timer, _callback, 0);
)

@change_callback_unused_data
 depends on match_timer_function_unused_data@
identifier match_timer_function_unused_data._callback;
type _origtype;
identifier _origarg;
@@

 void _callback(
-_origtype _origarg
+struct timer_list *unused
 )
 {
	... when != _origarg
 }

Signed-off-by: Kees Cook <keescook@chromium.org>
2017-11-21 15:57:07 -08:00
Gustavo A. R. Silva a3e2ecbae0 net: wan: x25_asy: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 114928
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-11 19:10:06 +09:00
David S. Miller 2a171788ba Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Files removed in 'net-next' had their license header updated
in 'net'.  We take the remove from 'net-next'.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-04 09:26:51 +09:00
Linus Torvalds ead751507d License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
 makes it harder for compliance tools to determine the correct license.
 
 By default all files without license information are under the default
 license of the kernel, which is GPL version 2.
 
 Update the files which contain no license information with the 'GPL-2.0'
 SPDX license identifier.  The SPDX identifier is a legally binding
 shorthand, which can be used instead of the full boiler plate text.
 
 This patch is based on work done by Thomas Gleixner and Kate Stewart and
 Philippe Ombredanne.
 
 How this work was done:
 
 Patches were generated and checked against linux-4.14-rc6 for a subset of
 the use cases:
  - file had no licensing information it it.
  - file was a */uapi/* one with no licensing information in it,
  - file was a */uapi/* one with existing licensing information,
 
 Further patches will be generated in subsequent months to fix up cases
 where non-standard license headers were used, and references to license
 had to be inferred by heuristics based on keywords.
 
 The analysis to determine which SPDX License Identifier to be applied to
 a file was done in a spreadsheet of side by side results from of the
 output of two independent scanners (ScanCode & Windriver) producing SPDX
 tag:value files created by Philippe Ombredanne.  Philippe prepared the
 base worksheet, and did an initial spot review of a few 1000 files.
 
 The 4.13 kernel was the starting point of the analysis with 60,537 files
 assessed.  Kate Stewart did a file by file comparison of the scanner
 results in the spreadsheet to determine which SPDX license identifier(s)
 to be applied to the file. She confirmed any determination that was not
 immediately clear with lawyers working with the Linux Foundation.
 
 Criteria used to select files for SPDX license identifier tagging was:
  - Files considered eligible had to be source code files.
  - Make and config files were included as candidates if they contained >5
    lines of source
  - File already had some variant of a license header in it (even if <5
    lines).
 
 All documentation files were explicitly excluded.
 
 The following heuristics were used to determine which SPDX license
 identifiers to apply.
 
  - when both scanners couldn't find any license traces, file was
    considered to have no license information in it, and the top level
    COPYING file license applied.
 
    For non */uapi/* files that summary was:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|-------
    GPL-2.0                                              11139
 
    and resulted in the first patch in this series.
 
    If that file was a */uapi/* path one, it was "GPL-2.0 WITH
    Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|-------
    GPL-2.0 WITH Linux-syscall-note                        930
 
    and resulted in the second patch in this series.
 
  - if a file had some form of licensing information in it, and was one
    of the */uapi/* ones, it was denoted with the Linux-syscall-note if
    any GPL family license was found in the file or had no licensing in
    it (per prior point).  Results summary:
 
    SPDX license identifier                            # files
    ---------------------------------------------------|------
    GPL-2.0 WITH Linux-syscall-note                       270
    GPL-2.0+ WITH Linux-syscall-note                      169
    ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
    ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
    LGPL-2.1+ WITH Linux-syscall-note                      15
    GPL-1.0+ WITH Linux-syscall-note                       14
    ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
    LGPL-2.0+ WITH Linux-syscall-note                       4
    LGPL-2.1 WITH Linux-syscall-note                        3
    ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
    ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1
 
    and that resulted in the third patch in this series.
 
  - when the two scanners agreed on the detected license(s), that became
    the concluded license(s).
 
  - when there was disagreement between the two scanners (one detected a
    license but the other didn't, or they both detected different
    licenses) a manual inspection of the file occurred.
 
  - In most cases a manual inspection of the information in the file
    resulted in a clear resolution of the license that should apply (and
    which scanner probably needed to revisit its heuristics).
 
  - When it was not immediately clear, the license identifier was
    confirmed with lawyers working with the Linux Foundation.
 
  - If there was any question as to the appropriate license identifier,
    the file was flagged for further research and to be revisited later
    in time.
 
 In total, over 70 hours of logged manual review was done on the
 spreadsheet to determine the SPDX license identifiers to apply to the
 source files by Kate, Philippe, Thomas and, in some cases, confirmation
 by lawyers working with the Linux Foundation.
 
 Kate also obtained a third independent scan of the 4.13 code base from
 FOSSology, and compared selected files where the other two scanners
 disagreed against that SPDX file, to see if there was new insights.  The
 Windriver scanner is based on an older version of FOSSology in part, so
 they are related.
 
 Thomas did random spot checks in about 500 files from the spreadsheets
 for the uapi headers and agreed with SPDX license identifier in the
 files he inspected. For the non-uapi files Thomas did random spot checks
 in about 15000 files.
 
 In initial set of patches against 4.14-rc6, 3 files were found to have
 copy/paste license identifier errors, and have been fixed to reflect the
 correct identifier.
 
 Additionally Philippe spent 10 hours this week doing a detailed manual
 inspection and review of the 12,461 patched files from the initial patch
 version early this week with:
  - a full scancode scan run, collecting the matched texts, detected
    license ids and scores
  - reviewing anything where there was a license detected (about 500+
    files) to ensure that the applied SPDX license was correct
  - reviewing anything where there was no detection but the patch license
    was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
    SPDX license was correct
 
 This produced a worksheet with 20 files needing minor correction.  This
 worksheet was then exported into 3 different .csv files for the
 different types of files to be modified.
 
 These .csv files were then reviewed by Greg.  Thomas wrote a script to
 parse the csv files and add the proper SPDX tag to the file, in the
 format that the file expected.  This script was further refined by Greg
 based on the output to detect more types of files automatically and to
 distinguish between header and source .c files (which need different
 comment types.)  Finally Greg ran the script using the .csv files to
 generate the patches.
 
 Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
 Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
 Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
 6dVh26uchcEQLN/XqUDt
 =x306
 -----END PGP SIGNATURE-----

Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull initial SPDX identifiers from Greg KH:
 "License cleanup: add SPDX license identifiers to some files

  Many source files in the tree are missing licensing information, which
  makes it harder for compliance tools to determine the correct license.

  By default all files without license information are under the default
  license of the kernel, which is GPL version 2.

  Update the files which contain no license information with the
  'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
  binding shorthand, which can be used instead of the full boiler plate
  text.

  This patch is based on work done by Thomas Gleixner and Kate Stewart
  and Philippe Ombredanne.

  How this work was done:

  Patches were generated and checked against linux-4.14-rc6 for a subset
  of the use cases:

   - file had no licensing information it it.

   - file was a */uapi/* one with no licensing information in it,

   - file was a */uapi/* one with existing licensing information,

  Further patches will be generated in subsequent months to fix up cases
  where non-standard license headers were used, and references to
  license had to be inferred by heuristics based on keywords.

  The analysis to determine which SPDX License Identifier to be applied
  to a file was done in a spreadsheet of side by side results from of
  the output of two independent scanners (ScanCode & Windriver)
  producing SPDX tag:value files created by Philippe Ombredanne.
  Philippe prepared the base worksheet, and did an initial spot review
  of a few 1000 files.

  The 4.13 kernel was the starting point of the analysis with 60,537
  files assessed. Kate Stewart did a file by file comparison of the
  scanner results in the spreadsheet to determine which SPDX license
  identifier(s) to be applied to the file. She confirmed any
  determination that was not immediately clear with lawyers working with
  the Linux Foundation.

  Criteria used to select files for SPDX license identifier tagging was:

   - Files considered eligible had to be source code files.

   - Make and config files were included as candidates if they contained
     >5 lines of source

   - File already had some variant of a license header in it (even if <5
     lines).

  All documentation files were explicitly excluded.

  The following heuristics were used to determine which SPDX license
  identifiers to apply.

   - when both scanners couldn't find any license traces, file was
     considered to have no license information in it, and the top level
     COPYING file license applied.

     For non */uapi/* files that summary was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0                                              11139

     and resulted in the first patch in this series.

     If that file was a */uapi/* path one, it was "GPL-2.0 WITH
     Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
     was:

       SPDX license identifier                            # files
       ---------------------------------------------------|-------
       GPL-2.0 WITH Linux-syscall-note                        930

     and resulted in the second patch in this series.

   - if a file had some form of licensing information in it, and was one
     of the */uapi/* ones, it was denoted with the Linux-syscall-note if
     any GPL family license was found in the file or had no licensing in
     it (per prior point). Results summary:

       SPDX license identifier                            # files
       ---------------------------------------------------|------
       GPL-2.0 WITH Linux-syscall-note                       270
       GPL-2.0+ WITH Linux-syscall-note                      169
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
       ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
       LGPL-2.1+ WITH Linux-syscall-note                      15
       GPL-1.0+ WITH Linux-syscall-note                       14
       ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
       LGPL-2.0+ WITH Linux-syscall-note                       4
       LGPL-2.1 WITH Linux-syscall-note                        3
       ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
       ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

     and that resulted in the third patch in this series.

   - when the two scanners agreed on the detected license(s), that
     became the concluded license(s).

   - when there was disagreement between the two scanners (one detected
     a license but the other didn't, or they both detected different
     licenses) a manual inspection of the file occurred.

   - In most cases a manual inspection of the information in the file
     resulted in a clear resolution of the license that should apply
     (and which scanner probably needed to revisit its heuristics).

   - When it was not immediately clear, the license identifier was
     confirmed with lawyers working with the Linux Foundation.

   - If there was any question as to the appropriate license identifier,
     the file was flagged for further research and to be revisited later
     in time.

  In total, over 70 hours of logged manual review was done on the
  spreadsheet to determine the SPDX license identifiers to apply to the
  source files by Kate, Philippe, Thomas and, in some cases,
  confirmation by lawyers working with the Linux Foundation.

  Kate also obtained a third independent scan of the 4.13 code base from
  FOSSology, and compared selected files where the other two scanners
  disagreed against that SPDX file, to see if there was new insights.
  The Windriver scanner is based on an older version of FOSSology in
  part, so they are related.

  Thomas did random spot checks in about 500 files from the spreadsheets
  for the uapi headers and agreed with SPDX license identifier in the
  files he inspected. For the non-uapi files Thomas did random spot
  checks in about 15000 files.

  In initial set of patches against 4.14-rc6, 3 files were found to have
  copy/paste license identifier errors, and have been fixed to reflect
  the correct identifier.

  Additionally Philippe spent 10 hours this week doing a detailed manual
  inspection and review of the 12,461 patched files from the initial
  patch version early this week with:

   - a full scancode scan run, collecting the matched texts, detected
     license ids and scores

   - reviewing anything where there was a license detected (about 500+
     files) to ensure that the applied SPDX license was correct

   - reviewing anything where there was no detection but the patch
     license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
     applied SPDX license was correct

  This produced a worksheet with 20 files needing minor correction. This
  worksheet was then exported into 3 different .csv files for the
  different types of files to be modified.

  These .csv files were then reviewed by Greg. Thomas wrote a script to
  parse the csv files and add the proper SPDX tag to the file, in the
  format that the file expected. This script was further refined by Greg
  based on the output to detect more types of files automatically and to
  distinguish between header and source .c files (which need different
  comment types.) Finally Greg ran the script using the .csv files to
  generate the patches.

  Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
  Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
  Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  License cleanup: add SPDX license identifier to uapi header files with a license
  License cleanup: add SPDX license identifier to uapi header files with no license
  License cleanup: add SPDX GPL-2.0 license identifier to files with no license
2017-11-02 10:04:46 -07:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Colin Ian King 3a1246fcbc wan: wanxl: remove redundant assignment to stat
stat set to zero and the value is never read, instead stat is
set again in the do-loop. Hence the setting to zero is redundant
and can be removed. Cleans up clang warning:

drivers/net/wan/wanxl.c:737:2: warning: Value stored to 'stat'
is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02 15:48:16 +09:00
David S. Miller ed29668d1a Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Smooth Cong Wang's bug fix into 'net-next'.  Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-02 15:23:39 +09:00
Pan Bian 7db8874abd net: lapbether: fix double free
The function netdev_priv() returns the private data of the device. The
memory to store the private data is allocated in alloc_netdev() and is
released in netdev_free(). Calling kfree() on the return value of
netdev_priv() after netdev_free() results in a double free bug.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-11-01 12:11:02 +09:00
Kees Cook 032cfd66af drivers/net: wan/sdla: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Allen Pais <allen.lkml@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27 12:09:16 +09:00
Kees Cook 605ea2f935 drivers/net: wan/lmc: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Allen Pais <allen.lkml@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27 12:09:16 +09:00
Kees Cook e2009be038 drivers/net: wan/dscc4: Remove unused timer
This removes an entirely unused timer, which avoids needing to convert it
to timer_setup().

Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-27 12:09:16 +09:00
Kees Cook 56546e3b9f drivers/net: wan/sbni: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: David Howells <dhowells@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-25 13:20:30 +09:00
Kees Cook d26c089e78 hdlc: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. This adds a pointer back to the
net_device, and drops needless open-coded resetting of the .function and
.data fields.

Cc: David S. Miller <davem@davemloft.net>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-18 12:39:55 +01:00
Allen Pais 802be57134 net: wan : hdlc: use setup_timer() helper
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 15:48:46 -07:00
Allen Pais 19569c88b9 drivers: net: lmc: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:44 -07:00
Allen Pais 8d81fe753c drivers: net: hdlc_ppp: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:43 -07:00
Allen Pais f2803332f2 drivers: net: dscc: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:43 -07:00
Allen Pais dffec39fb1 drivers: net: cisco_hdlc: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:40 -07:00
Allen Pais f347bd6b5f drivers: net: sdla: use setup_timer() helper.
Use setup_timer function instead of initializing timer with the
    function and data fields.

Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-21 11:44:40 -07:00
Linus Torvalds 44ccba3f7b - For the randstruct plugin, enable automatic randomization of structures
that are entirely function pointers (along with a couple designated
   initializer fixes).
 - For the structleak plugin, provide an option to perform zeroing
   initialization of all otherwise uninitialized stack variables that are
   passed by reference (Ard Biesheuvel).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 Comment: Kees Cook <kees@outflux.net>
 
 iQIcBAABCgAGBQJZrwHlAAoJEIly9N/cbcAmJR0QAKsTL0B6iBJlzrcAj6HkloMu
 QTTx+qrdpuhEJ+mH10JpOJnFctVI3vt7tUXGhBb0eBXuvnXPACjy3jx2X1tcnKf4
 v2HLf2GuCb95HqDVgrzn+HNPiAPb0dEM7qJPV+VfZA0K2nb6dVmS9fDYQWCLGJI+
 aazpmJDAOhXuKtUsbONaomoygBbS2kYrYCzqYB4M0FmZvbKw4CUdvVonkxhAITtl
 Zj3cl++jgHnVSNmyk92n3LTbIOv/o+pAMWv3/K6KDUIsNtVyk4znaghQJ6VKZhoR
 ua1gGzd0vrKMm960y8sDve+w5JSwaHVq6Y4jeqQynZywDpB998IhQiLmWfdSoN0O
 BPzAkxdNjCGNe+Ro6fQWYAXvnBZN2Gw8RiIjJP5DEz8EXe2BgGAFn3C6xbIS+F+A
 mXcn3Chorc1ZEfwMrbQ24vTfHRNmwMYQbZYZ9XftzixJU8XXhAf135DS+Enrc09X
 eSWEWaAJuF4en8A+1CsxO7vMh3U8tcS2lldbEUgXCJlNExzYFxBHwB2GImYXUt9D
 1i74n0PSz3EA8zfVr3qsGdraJq+7Ubq2NRWoudtQPYbHIh+VZcQ2VQEFtWOkmlgB
 T4foN7s17MrZzxn8krlYy8yODFJkisRJi/A5ox7hERwZjAhMQdwbTEr8HhKTui6X
 rm73yglE4ebfidp4Iyq4
 =3jxS
 -----END PGP SIGNATURE-----

Merge tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux

Pull gcc plugins update from Kees Cook:
 "This finishes the porting work on randstruct, and introduces a new
  option to structleak, both noted below:

   - For the randstruct plugin, enable automatic randomization of
     structures that are entirely function pointers (along with a couple
     designated initializer fixes).

   - For the structleak plugin, provide an option to perform zeroing
     initialization of all otherwise uninitialized stack variables that
     are passed by reference (Ard Biesheuvel)"

* tag 'gcc-plugins-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  gcc-plugins: structleak: add option to init all vars used as byref args
  randstruct: Enable function pointer struct detection
  drivers/net/wan/z85230.c: Use designated initializers
  drm/amd/powerplay: rv: Use designated initializers
2017-09-07 20:30:19 -07:00
Alexey Khoroshilov ba6ba68f59 wan: dscc4: convert to plain DMA API
Make use the dma_*() interfaces rather than the pci_*() interfaces.

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-11 14:42:28 -07:00
Alexey Khoroshilov 6aa200058e wan: dscc4: add checks for dma mapping errors
The driver does not check if mapping dma memory succeed.
The patch adds the checks and failure handling.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-08-11 14:42:28 -07:00
Kees Cook 3598f5d087 drivers/net/wan/z85230.c: Use designated initializers
In preparation for the randstruct gcc plugin performing randomization of
structures that are entirely function pointers, use designated initializers
so the compiler doesn't get angry.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
2017-08-01 17:04:38 -07:00
Johannes Berg af72868b90 networking: make skb_pull & friends return void pointers
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = {
            skb_pull,
            __skb_pull,
            skb_pull_inline,
            __pskb_pull_tail,
            __pskb_pull,
            pskb_pull
    };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = {
            skb_pull,
            __skb_pull,
            skb_pull_inline,
            __pskb_pull_tail,
            __pskb_pull,
            pskb_pull
    };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:39 -04:00
Johannes Berg 4df864c1d9 networking: make skb_put & friends return void pointers
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_put, __skb_put };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_put, __skb_put };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

which actually doesn't cover pskb_put since there are only three
users overall.

A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:39 -04:00
Johannes Berg 59ae1d127a networking: introduce and use skb_put_data()
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)

Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:37 -04:00
David S. Miller 0ddead90b2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
The conflicts were two cases of overlapping changes in
batman-adv and the qed driver.

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-15 11:59:32 -04:00
David S. Miller cf124db566 net: Fix inconsistent teardown and release of private netdev state.
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init().  However, the release of these resources
can occur in one of two different places.

Either netdev_ops->ndo_uninit() or netdev->destructor().

The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.

netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.

netdev->destructor(), on the other hand, does not run until the
netdev references all go away.

Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().

This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.

If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit().  But
it is not able to invoke netdev->destructor().

This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.

However, this means that the resources that would normally be released
by netdev->destructor() will not be.

Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.

Many drivers do not try to deal with this, and instead we have leaks.

Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().

netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().

netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().

Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().

And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-07 15:53:24 -04:00
Holger Brunck 85deed5603 net/wan/fsl_ucc_hdlc: fix muram allocation error
sizeof(priv->ucc_pram) is 4 as it is the size of a pointer, but we want
to reserve space for the struct ucc_hdlc_param.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-22 12:28:45 -04:00
Holger Brunck 067bb938da net/wan/fsl_ucc_hdlc: add hdlc-bus support
This adds support for hdlc-bus mode to the fsl_ucc_hdlc driver. This can
be enabled with the "fsl,hdlc-bus" property in the DTS node of the
corresponding ucc.

This aligns the configuration of the UPSMR and GUMR registers to what is
done in our ucc_hdlc driver (that only support hdlc-bus mode) and with
the QuickEngine's documentation for hdlc-bus mode.

GUMR/SYNL is set to AUTO for the busmode as in this case the CD signal
is ignored. The brkpt_support is enabled to set the HBM1 bit in the
CMXUCR register to configure an open-drain connected HDLC bus.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:39 -04:00
Holger Brunck 54e9e08749 net/wan/fsl_ucc_hdlc: call qe_setbrg only for loopback mode
We can't assume that we are always in loopback mode if rx and tx clock
have the same clock source. If we want to use HDLC busmode we also have
the same clock source but we are not in loopback mode. So move the
setting of the baudrate generator after the check for property for the
loopback mode.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:38 -04:00
Holger Brunck 5b8aad93c5 net/wan/fsl_ucc_hdlc: fix incorrect memory allocation
We need space for the struct qe_bd and not for a pointer to this struct.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:38 -04:00
Holger Brunck 10515db509 net/wan/fsl_ucc_hdlc: fix wrong indentation
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:38 -04:00
Holger Brunck 66bb144bd9 net/wan/fsl_ucc_hdlc: fix unitialized variable warnings
This fixes the following compiler warnings:
drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_poll':
warning: 'skb' may be used uninitialized in this function
[-Wmaybe-uninitialized]
  skb->mac_header = skb->data - skb->head;

and

drivers/net/wan/fsl_ucc_hdlc.c: In function 'ucc_hdlc_probe':
drivers/net/wan/fsl_ucc_hdlc.c:1127:3: warning: 'utdm' may be used
uninitialized in this function [-Wmaybe-uninitialized]
   kfree(utdm);

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:38 -04:00
Holger Brunck f089785479 net/wan/fsl_ucc_hdlc: cleanup debug traces
Some of the tracing seems to be remaining traces for basic driver
development. They can be removed now, as they cause noisy printouts.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:28:37 -04:00
Alexey Dobriyan 0cd2950357 net: make struct net_device::tx_queue_len unsigned int
4 billion packet queue is something unthinkable so use 32-bit value
for now.

Space savings on x86_64:

	add/remove: 0/0 grow/shrink: 3/70 up/down: 16/-131 (-115)
	function                                     old     new   delta
	change_tx_queue_len                           94     108     +14
	qdisc_create                                1176    1177      +1
	alloc_netdev_mqs                            1124    1125      +1
	xenvif_alloc                                 533     532      -1
	x25_asy_setup                                167     166      -1
			...
	tun_queue_resize                             945     940      -5
	pfifo_fast_enqueue                           167     162      -5
	qfq_init_qdisc                               168     158     -10
	tap_queue_resize                             810     799     -11
	transmit                                     719     698     -21

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-05-18 10:19:30 -04:00
Linus Torvalds 291b38a756 Annotation of module parameters that specify device settings
-----BEGIN PGP SIGNATURE-----
 
 iQIVAwUAWPiW6vSw1s6N8H32AQLOrw/+NTqGf7bjq+64YKS6NfR0XDgE+wNJltGO
 ck7zJW3NHIg76RNu8s0I9xg5aVmwizz3Z5DGROZquaolnezux4tQihZ3AFyxIzLc
 +Y3WHYagcML7yFfjl/WznCLRD5EW3yPln4lCvQO0nW/xICRYeRI057JaIbi2Dtek
 BhcXt3c4AjXDLdYJkgtHV3p2R2mt8hcdFdWqqx6s7JaIThZNRGNzxAgtbcB9k5IW
 HVG9ZEIL73VBYWHrYivzjHYF5rBnNCPt87eOwDQeTOSkhv8te+u9k+bH8vxZw1T0
 XUtDrLBndKiuVo2GUfLkkF8LItx3Q9eLCJYy0joaIliyPqTEsPx9KjQ+Af0cxS9s
 ZPCZ5SYf96stKmDeL5xaMfrAmeyVHJ4lc4JTOqdzbIT8blsOSfYO/03p0ALShSDv
 /RQLaKGlf8Bjoy8PwKFcXb4sIDufcd/U1Av/EMFXxOfgN/u2JUkGKq6EaIM5B68L
 fHPje+aR9VNELPmPjwNOWtmN4I79EH3EItQf7zv0KG+UeKhcHLx/EAcSJ3ZRKEkH
 Lathg7pPOEJGArPiVO79TZzBG01ADn1aiwv65XObMzNZ+54xI/mN/Y1DNF/kL5jU
 XzvNzEjFt8mwMIZGVNdAt4+pDyMfIZGZSyUkSRKFnaQZMIvQrfQIU9RLBYLX5eOx
 +/p0VkIwDpg=
 =lbS7
 -----END PGP SIGNATURE-----

Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull hw lockdown support from David Howells:
 "Annotation of module parameters that configure hardware resources
  including ioports, iomem addresses, irq lines and dma channels.

  This allows a future patch to prohibit the use of such module
  parameters to prevent that hardware from being abused to gain access
  to the running kernel image as part of locking the kernel down under
  UEFI secure boot conditions.

  Annotations are made by changing:

        module_param(n, t, p)
        module_param_named(n, v, t, p)
        module_param_array(n, t, m, p)

  to:

        module_param_hw(n, t, hwtype, p)
        module_param_hw_named(n, v, t, hwtype, p)
        module_param_hw_array(n, t, hwtype, m, p)

  where the module parameter refers to a hardware setting

  hwtype specifies the type of the resource being configured. This can
  be one of:

        ioport          Module parameter configures an I/O port
        iomem           Module parameter configures an I/O mem address
        ioport_or_iomem Module parameter could be either (runtime set)
        irq             Module parameter configures an I/O port
        dma             Module parameter configures a DMA channel
        dma_addr        Module parameter configures a DMA buffer address
        other           Module parameter configures some other value

  Note that the hwtype is compile checked, but not currently stored (the
  lockdown code probably won't require it). It is, however, there for
  future use.

  A bonus is that the hwtype can also be used for grepping.

  The intention is for the kernel to ignore or reject attempts to set
  annotated module parameters if lockdown is enabled. This applies to
  options passed on the boot command line, passed to insmod/modprobe or
  direct twiddling in /sys/module/ parameter files.

  The module initialisation then needs to handle the parameter not being
  set, by (1) giving an error, (2) probing for a value or (3) using a
  reasonable default.

  What I can't do is just reject a module out of hand because it may
  take a hardware setting in the module parameters. Some important
  modules, some ipmi stuff for instance, both probe for hardware and
  allow hardware to be manually specified; if the driver is aborts with
  any error, you don't get any ipmi hardware.

  Further, trying to do this entirely in the module initialisation code
  doesn't protect against sysfs twiddling.

  [!] Note that in and of itself, this series of patches should have no
      effect on the the size of the kernel or code execution - that is
      left to a patch in the next series to effect. It does mark
      annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
      an already existing field"

* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
  Annotate hardware config module parameters in sound/pci/
  Annotate hardware config module parameters in sound/oss/
  Annotate hardware config module parameters in sound/isa/
  Annotate hardware config module parameters in sound/drivers/
  Annotate hardware config module parameters in fs/pstore/
  Annotate hardware config module parameters in drivers/watchdog/
  Annotate hardware config module parameters in drivers/video/
  Annotate hardware config module parameters in drivers/tty/
  Annotate hardware config module parameters in drivers/staging/vme/
  Annotate hardware config module parameters in drivers/staging/speakup/
  Annotate hardware config module parameters in drivers/staging/media/
  Annotate hardware config module parameters in drivers/scsi/
  Annotate hardware config module parameters in drivers/pcmcia/
  Annotate hardware config module parameters in drivers/pci/hotplug/
  Annotate hardware config module parameters in drivers/parport/
  Annotate hardware config module parameters in drivers/net/wireless/
  Annotate hardware config module parameters in drivers/net/wan/
  Annotate hardware config module parameters in drivers/net/irda/
  Annotate hardware config module parameters in drivers/net/hamradio/
  Annotate hardware config module parameters in drivers/net/ethernet/
  ...
2017-05-10 19:13:03 -07:00
Pan Bian 2a39e7aa8a wan: pc300too: abort path on failure
In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-04-24 15:51:31 -04:00
David Howells af28a03c1b Annotate hardware config module parameters in drivers/net/wan/
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image.  Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.

To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify.  The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.

Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.

This patch annotates drivers in drivers/net/wan/.

Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "Jan \"Yenya\" Kasprzak" <kas@fi.muni.cz>
cc: netdev@vger.kernel.org
2017-04-20 12:02:32 +01:00
Zhao Qiang 02bb56ddc6 ucc/hdlc: fix two little issue
1. modify bd_status from u32 to u16 in function hdlc_rx_done,
because bd_status register is 16bits
2. write bd_length register before writing bd_status register

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-03-13 21:53:48 -07:00
Ingo Molnar 174cd4b1e5 sched/headers: Prepare to move signal wakeup & sigpending methods from <linux/sched.h> into <linux/sched/signal.h>
Fix up affected files that include this signal functionality via sched.h.

Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-03-02 08:42:32 +01:00
Valentin Longchamp 74179d44b6 net/wan: add MODULE_LICENSE for fsl_ucc_hdlc
It is required to build it as a module.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-17 15:20:43 -05:00
Wei Yongjun fee402211f net: wan: slic_ds26522: Remove .owner field for driver
Remove .owner field if calls are used which set it automatically.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-07 11:41:15 -05:00
Wei Yongjun c3afa99553 net: wan: slic_ds26522: Use module_spi_driver to simplify the code
module_spi_driver() makes the code simpler by eliminating
boilerplate code.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-07 11:41:15 -05:00
Eric Dumazet 6ad20165d3 drivers: net: generalize napi_complete_done()
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")

This allows for more efficient GRO aggregation without
sacrifying latencies.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-01-30 15:10:42 -05:00