The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the requested gpio property is not found in the device tree, some
callers of gpiod_get_from_of_node() expect a return value of NULL, others
expect -ENOENT.
In particular devm_fwnode_get_index_gpiod_from_child() expects -ENOENT.
Currently it gets a NULL, which breaks the loop that tries all
gpio_suffixes. The result is that a gpio property is not found, even
though it is there.
This patch changes gpiod_get_from_of_node() to return -ENOENT instead
of NULL when the requested gpio property is not found in the device
tree. Additionally it modifies all calling functions to properly
evaluate the return value.
Another approach would be to leave the return value of
gpiod_get_from_of_node() as is and fix the bug in
devm_fwnode_get_index_gpiod_from_child(). Other callers would still need
to be reworked. The effort would be the same as with the chosen solution.
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver supported turning off regulators in suspend only for S2MPS14
device. However this makes also sense for S2MPS11 and can reduce the
power consumption during suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the regulator ID instead of calling rdev_get_id() every time.
This makes code slightly easier to read as shorter 'rdev_id' variable is
used instead of full call. This can also speed things up by reducing
number of calls, although effect was not measured.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_gpiod_get_from_of_node() call returns ERR_PTR, it is assigned
into an array of GPIO descriptors and used later because such error is
not treated as critical thus it is not propagated back to the probe
function.
All code later expects that such GPIO descriptor is either a NULL or
proper value. This later might lead to dereference of ERR_PTR.
Only devices with S2MPS14 flavor are affected (other do not control
regulators with GPIOs).
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step
instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or
under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420
Arndale Octa board).
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
GPIO descriptor array must be zero initialized to ensure that core will
properly handle also the case when no external GPIO pin is defined.
Fixes: 1c984942f0 ("regulator: s2mps11: Pass descriptor instead of GPIO number")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up with the standard devm_gpiod_get_optional()
call.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Tested on Odroid XU3 (with s2mps11 although not using any GPIOs
for regulators, so at least default paths are not broken).
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace GPL v2.0+ license statements with SPDX license
identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static struct regulator_ops is not modified so can be made const for
code safeness.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes some of the LDOs and BUCKs voltage range as per
user manual of s2mps15 (REV0.4).
Fixes: 51af206758 ("regulator: s2mps11: Add support for S2MPS15 regulators")
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Driver did not provide default value for ramp delay for LDOs which lead
to warning in dmesg, e.g. on Odroid XU4:
[ 1.486076] vdd_ldo9: ramp_delay not set
[ 1.506875] vddq_mmc2: ramp_delay not set
[ 1.523766] vdd_ldo15: ramp_delay not set
[ 1.544702] vdd_sd: ramp_delay not set
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver's init and exit function don't do anything besides registering
and unregistering the platform driver, so the module_platform_driver()
macro could just be used instead of having separate functions.
Currently the macro is not being used because the driver is initialized at
subsys init call level but this isn't necessary since consumer devices are
defined in the DT as dependencies so there's no need for init calls order.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Remove the s2mps11_info.rdev_num because it is not used outside of
probe.
Suggested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Following BUILD_BUG_ON using a variable fails for some of the compilers
and optimization levels (reported for gcc 4.9):
var = ARRAY_SIZE(s2mps15_regulators);
BUILD_BUG_ON(S2MPS_REGULATOR_MAX < var);
Fix this by using ARRAY_SIZE directly.
Additionally add missing BUILD_BUG_ON check for S2MPS15 device (the
check ensures that internal arrays are big enough to hold data for all
of regulators on all devices).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently S2MPSXX multifunction device is named as *-pmic,
and these MFDs also supports regulator as a one of its MFD cell which
has the same name, because current name is confusing and we want to
sort it out.
We did discussed different approaches about how the MFD and it
cells need to be named here [1].
Based in the discussion this patch rename MFD regulator name as
*-regulator instead of current *-pmic.
This patch also changes the corresponding entries in the regulator driver
to keep git-bisect happy.
[1]-> https://lkml.org/lkml/2015/10/28/417
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS15 PMIC is similar in functionality to S2MPS11/14 PMIC. It contains
27 LDO and 10 Buck regulators and allows programming these regulators via a
I2C interface. This patch adds initial support for LDO/Buck regulators of
S2MPS15 PMIC.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Status of enabling suspend mode for regulator was stored in bitmap-like
long integer.
However since adding support for S2MPU02 the number of regulators
exceeded 32 so on devices with more than 32 regulators (S2MPU02 and
S2MPS13) overflow happens when shifting the bit. This could lead to
enabling suspend mode for completely different regulator than intended
or to switching different regulator to other mode (e.g. from always
enabled to controlled by PWRHOLD pin). Both cases could result in larger
energy usage and issues when suspending to RAM.
Fixes: 00e2573d2c ("regulator: s2mps11: Add support S2MPU02 regulator device")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Remove unneeded semicolons after the switch statement to satisfy
coccicheck.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing registers('BUCK7_SW' & 'LDO29_CTRL'). Since BUCK7 has
1 more register (BUCK7_SW) than others, register offset should
be added one more for which has bigger address than BUCK7 registers.
Fixes: 76b9840b24ae04(regulator: s2mps11: Add support S2MPS13 regulator device)
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
One fix here, a fix for the voltage mapping on one of the s2mps11
regulators which broke systems using it including apparently the Gear 2
smartwatches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoX7vAAoJECTWi3JdVIfQtcEH/junzpSCOwIrI8NG9/ZF0xt5
rLB1SlDxtiSPv6eFA+KXYYmO8VNjZ1g+NN1PoeSNgAK08YzG9IUHIqI1L1iDe2qG
2vpPY++Rg5eWPY79Sa9oy/+2zmFmUh3t+Shv7p3WC1Q8GES4bD6dm/QVxykh16nW
nDGYZN981THIHS9xPKsmvCbHMp6PknDZkqO9Umzflt7cYgzgFP8xTaTlb4vkwTza
3ZjGnEMIe1ldkLGFEJmdsSMro07hKzVYk8e3auOK+gAMpO+QjpY8WxuarmpQBPLx
GddKhfkox5HNUxm9jRp0jivgi8YXD4a1lXzwXpxSihax1Q/Q/v00yoJ6selRQXg=
=/mpj
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull one regulator fix from Mark Brown:
"One fix here, a fix for the voltage mapping on one of the s2mps11
regulators which broke systems using it including apparently the
Gear 2 smartwatches"
* tag 'regulator-v3.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: s2mps11: Fix dw_mmc failure on Gear 2
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Invalid buck4 configuration for linear mapping of voltage in S2MPS14
regulators caused boot failure on Gear 2 (dw_mmc-exynos):
[ 3.569137] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null)
[ 3.571716] VFS: Mounted root (ext4 filesystem) readonly on device 179:15.
[ 3.629842] mmcblk0: error -110 sending status command, retrying
[ 3.630244] mmcblk0: error -110 sending status command, retrying
[ 3.636292] mmcblk0: error -110 sending status command, aborting
Buck4 voltage regulator has different minimal voltage value than other
bucks. Commit merging multiple regulator description macros caused to
use linear_min_sel from buck[1235] regulators as value for buck4. This
lead to lower voltage of buck4 than required.
Output of the buck4 is used internally as power source for
LDO{3,4,7,11,19,20,21,23}. On Gear 2 board LDO11 is used as MMC
regulator (V_EMMC_1.8V).
Fixes: 5a867cf288 ("regulator: s2mps11: Optimize the regulator description macro")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
- Support for specifying the target regulation mode and voltage during
system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhaLEAAoJECTWi3JdVIfQMIEH/0n/0TJngSaoifV72PCkICdx
GbNs2bUkjuNAbYw6S6xmbA6MYPEllGiFnmJPRjV41qf0a1TTG/vam3fjeaBao7En
DxEBsz22iuBM4wmOSEKTsDtTRuiX170cqKKWZ4ugFo/uaDinueW2tz0Uzvz05or5
bSxT8hbeYerNksb13mn7OjW8r0rCE24w1K669MZgwp0uuIY+NKUTnwT4TqMzDo5c
OT4RQ2XZAQOhOfqS4VTR07Ab8PzGQd4zzmTYljqd2MKL7ubKz41vNSnGHwPdrTH1
FeQ9Q/JZl0W6zwUjltGfZLjDewD1Kcb+3gdgCiD+V8wQQ1xg8H15nql4WpK6P8s=
=bMvT
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
Summary:
- Support for specifying the target regulation mode and voltage
during system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033"
* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
regulator: sky81452: Modify Device Tree structure
regulator: sky81452: Modify Device Tree structure
dt-bindings: Update documentation for "system-power-controller" and fix misspellings
of: Rename "poweroff-source" property to "system-power-controller"
regulator: max77686: Remove support for board files
regulator: max77802: Remove support for board files
regulator: max77802: Fill regulator modes translation callback
regulator: max77802: Document binding for regulator operating modes
regulator: of: Add support for parsing initial and suspend modes
regulator: of: Pass the regulator description in the match table
regulator: of: Add regulator desc param to of_get_regulator_init_data()
regulator: Add mode mapping function to struct regulator_desc
regulator: Document binding for initial and suspend modes
regulator: core: Add PRE_DISABLE notification
regulator: gpio: fix parsing of gpio list
regulator: rpm: add support for RPM-controller SMB208
regulator: da9063: Do not transform local IRQ to virtual
regulator: sky81452: Modify dependent Kconfig symbol
regulator: rt5033: Add RT5033 Regulator device driver
...
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch sets ena_gpio_initialized for all drivers which set a
ena_gpio from parsed DT properties. Drivers using pdata may get zero
initialized pdata and therefore copy a 0 into the regulator_config
ena_gpio field.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was allocating memory for storing GPIOs for external control
with unnecessary GFP_ZERO flag. Then right after allocation it
initialized memory to -EINVAL in loop. Skip the GFP_ZERO flag.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add S2MPU02 regulator device to existing S2MPS11 device driver
because of little difference between S2MPS1x and S2MPU02. The S2MPU02
regulator device includes LDO[1-28] and BUCK[1-7].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Add missing linear_min_sel of S2MPU02 LDO regulators by Jonghwa Lee]
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
S2MPS11 supports enabling/disabling ramp delay only for buck[2346].
Other bucks have ramp delay enabled always.
However the bit shift for enabling buck6 ramp delay in register is equal
to 0. When ramp delay was set for the bucks unsupporting enable/disable
(buck[15789] and buck10), the ramp delay for buck6 was also enabled.
Fixes: b96244fad9 ("regulator: s2mps11: Don't check enable_shift before setting enable ramp rate")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
GPIO 0 is a valid GPIO so allow using it as external control for
S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for external control over GPIO for LDO10, LDO11 and LDO12
S2MPS14 regulators. External control can be turned on by writing 0x0 to
control register which in case of other regulators is used for disabling
them. These LDO10-LDO12 regulators can be disabled only by I2C GPIO or
PWREN pin so the patch actually allows proper way of disabling them.
Additionally the GPIO control has two benefits:
- It is faster than toggling it over I2C bus.
- It allows disabling the regulator during suspend to RAM; The AP will
enable it during resume.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor code for parsing DTS to increase a little code readability. The
behaviour should not change.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code misses updating the register when enable_shift is 0.
e.g. S2MPS11_BUCK9_RAMP_SHIFT and S2MPS11_BUCK6_RAMP_EN_SHIFT are 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
