Since a clocksource change post 3.2-rc1, tasks on my DB1500 board
hang after random amounts of time (from a few minutes to a few hours),
regardless of load. Debugging showed that the compare-match register
value is a few seconds lower than the current counter value.
The minimum value of 8 was initialy determined by a trial-and-error
approach. Currently it is sufficient for all Alchemys (without PCI
apparently), independent of CPU clock; only the DB1500 and DB1550
boards experience these timer-related tasks hangs now.
This patch increases the minimum timeout by 1 (to 9 counter ticks)
which seems sufficient since the systems are still working perfectly
fine after over 24 hours.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3214/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 has the CPLD located at an address which on the DB1200 is
RAM; reading the Board-ID sometimes results in a PB1200 being detected
instead (especially during reboots after long uptimes).
On the other hand, the address of the DB1200's CPLD is hosting Flash
chips on the PB1200. Test for the DB1200 first and additionally do a
quick write-test to the hexleds register to make sure we're writing
to the CPLD.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3005/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With a generic plat_irq_dispatch (for Alchemy at least) code for both
interrupt controller types can coexist in a single kernel image and be
autodetected at runtime.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2935/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add necessary transceiver control platform data and hook up the
IrDA peripheral on the DB1000 and DB1100 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Devboards can use the 32kHz counter as a RTC device.
Also delete the custom CMOS RTC header, which can be used for the
DS1693 on the PB1500. But since it doesn't have a buffer battery
it is as useful as the on-chip RTC which I prefer.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2874/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These 3 boards are very similar; with this patch a single kernel image
which runs on all three can be built.
Tested on DB1500 and DB1100.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PB1200 is basically a DB1200 with additional MMC and camera sockets
and different base addresses for external hardware (CPLD, IDE, Net, NAND).
This patch implements the missing PB1200 features in DB1200 support code
and runtime board detection.
Tested on DB1200 only.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2880/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these files are have more comments than real code; merge
them all into single board-<name>.c files.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Initially I had to write to both the MASK and ENABLE registers, otherwise
the CPLD would generate tons of spurious interrupts. With the change to
the demux handler to disable the muxed line, it is now sufficient to
disable the interrupt by writing either the enable or mask register.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2865/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No test hardware and no (apparent) users. These boards seem very
similar to the DB1500, so if required support can be brought back
again (I have datasheets) but then with dedicated board code, not
tacked on to DB1000 support.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2864/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch gets rid of all CONFIG_SOC_AU1XXX defines in
DMA/DBDMA-related code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xxx-ide uses defines from the pb1200/db1200 headers:
get DBDMA ID through platform resource information,
hardcode register spacing. The only 2 users of this driver (and
the only boards it can really work on realiably) use the same
register layout.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-ide@vger.kernel.org
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-ide@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/2716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
remove all redundant peripheral base address defines, fix
all affected boards and drivers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use runtime CPU detection to setup all USB parts.
Remove the Au1200 OTG and UDC platform devices since there are no
drivers for them anyway.
Clean up the USB address mess in the au1000 header.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/usb/host/alchemy-common.c
For GPIOLIB=y decide at runtime which gpiochips to register;
in the GPIOLIB=n case, the gpio headers need to be reshuffled
a bit to make multiple implementations coexist peacefully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2679/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No reason NOT to build it
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the last hardcoded base address from the au1000_eth
driver. The base address of the MACDMA unit was derived from the
platform device id; if someone registered the MACs in inverse order
both would not work.
So instead pass the base address of the DMA unit to the driver with
the other platform resource information.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: David S. Miller <davem@davemloft.net>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2674/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Disable the cascade IRQ in the cascade handler. This is required to
get the DB1300 working, and also gets rid of all spurious interrupts
previously observed on the DB1200; so Config[OD] can be disabled
again for better performance.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code forgets the Au1100 when looking for the correct method to
suspend the chip.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Harmless typo which prints an error message although MAC0 was registered
successfully.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The use of the "soc-audio" platform device is no longer en vogue,
update the code to the newer, simpler way of doing things.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PSC audio drivers (psc-ac97/psc-i2s) register the DMA platform_device
on their own. This is frowned upon, from now on board code must
register a simple pcm dma platform device for each PSC with sound duties.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a machine driver suitable for the AC97 part on the DB1000/DB1500/DB1100
boards.
Run-tested on DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'timers-clocksource-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: convert mips to generic i8253 clocksource
clocksource: convert x86 to generic i8253 clocksource
clocksource: convert footbridge to generic i8253 clocksource
clocksource: add common i8253 PIT clocksource
blackfin: convert to clocksource_register_hz
mips: convert to clocksource_register_hz/khz
sparc: convert to clocksource_register_hz/khz
alpha: convert to clocksource_register_hz
microblaze: convert to clocksource_register_hz/khz
ia64: convert to clocksource_register_hz/khz
x86: Convert remaining x86 clocksources to clocksource_register_hz/khz
Make clocksource name const
remove au_readl/au_writel, remove the predefined GPIO1/2 KSEG1 register
addresses and fix the fallout in all boards and drivers.
This also fixes a bug in the mtx-1_wdt driver which was introduced by
commit 6ea8115bb6
("Convert mtx1 wdt to be a platform device and use generic GPIO API")
before this patch mtx-1_wdt only modified GPIO215, the patch then
used the gpio resource information as bit index into the GPIO2 register
but the conversion to the GPIO API didn't realize that.
With this patch the drivers original behaviour is restored and GPIO15
is left alone.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Florian Fainelli <florian@openwrt.org>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-watchdog@vger.kernel.org
Cc: Wim Van Sebroeck <wim@iguana.be>
Patchwork: https://patchwork.linux-mips.org/patch/2381/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
According to the databooks, the Au1000 DMA engine must be programmed with
the physical FIFO addresses. This patch does that; furthermore this
opened the possibility to get rid of a lot of now unnecessary address
defines.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2348/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Rewrite ethernet setup to use runtime cpu detection, and also clean up
the ethernet base address mess as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Detect CPU type at runtime and setup uarts accordingly; also clean up the
uart base address mess in the process as far as possible.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2352/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org
Convert the PM sysdev to syscore_ops and clean up the ddma addresses a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2351/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the PM sysdev to use syscore_ops instead.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Patchwork: https://patchwork.linux-mips.org/patch/2350/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Manuel Lauss
Ralf Baechle
Yong Zhang
Linus Torvalds