When an XRDY/XDR is hit, wait for XUDF before writing data to DATA_REG.
Otherwise some data bytes can be lost while transferring them from the
memory to the I2C interface.
Do a Busy-wait for XUDF, before writing data to DATA_REG. While waiting
if there is NACK | AL, set the appropriate error flags, ack the pending
interrupts and return from the ISR.
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of a NACK or ARDY or AL interrupt, complete the request.
There is no need to service the RRDY/RDR or XRDY/XDR interrupts.
Refer TRM SWPU114: Figure 18-31.I2C Master Transmitter Mode, Interrupt Method,
in F/S and HS Modes
http://focus.ti.com/pdfs/wtbu/SWPU114T_PrelimFinalEPDF_06_25_2009.pdf
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix bug in reading the I2C_BUFFSTAT register for getting byte count on RX/TX interrupt.
On Interrupt: I2C_STAT[RDR],
read 'RXSTAT' from I2C_BUFFSTAT[8-13]
On Interrupt: I2C_STAT[XDR]
read 'TXSTAT' from I2C_BUFFSTAT[0-5]
Signed-off-by: Jagadeesh Pakaravoor <j-pakaravoor@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Vikram pandita <vikram.pandita@ti.com>
[ben-linux@fluff.org: fixed mail format and added i2c-omap to subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Convert the i2c-sh_mobile i2c bus driver to use
subsys_initcall() instead of module_init().
This change makes the driver register a bit earlier which
together with earlier platform data moves the time for probe().
The earlier probe() makes it possible to use i2c_get_adapter()
and i2c_transfer() from device_initcall().
The same strategy is used by other i2c bus drivers such as
i2c-pxa.c and i2c-s3c2410.c.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
[ben-linux@fluff.org: minor subject updaye]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
s3c24xx_i2c_init() was overwriting the IICLC value set just above in
s3c24xx_i2c_clockrate() with zero, effectively disabling the platform
line control setting.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
I've tested TSL2550 driver and I've found a bug: when light is off,
returned value from tsl2550_calculate_lux function is -1 when it should
be 0 (sensor correctly read that light was off).
I think the bug is that a zero c0 value (approximated value of ch0) is
misinterpreted as an error.
Signed-off-by: Michele Jr De Candia <michele.decandia@valueteam.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use the function resource_size, which reduces the chance of introducing
off-by-one errors in calculating the resource size.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct resource *res;
@@
- (res->end - res->start) + 1
+ resource_size(res)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make i2c-davinci cope properly with "i2cdetect": don't spew
syslog spam on perfectly normal behaviors, or respond to any
address other than the one reserved for the SMBus host.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
DaVinci core code has converted to the new clkdev API so
clock name strings are not needed. Instead, just the a
'struct device' pointer is needed.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This build error triggers on x86:
drivers/built-in.o: In function `i2c_dw_init':
i2c-designware.c:(.text+0x4e37ca): undefined reference to `clk_get_rate'
drivers/built-in.o: In function `dw_i2c_probe':
i2c-designware.c:(.devinit.text+0x51f5e): undefined reference to `clk_get'
i2c-designware.c:(.devinit.text+0x51f76): undefined reference to `clk_enable'
i2c-designware.c:(.devinit.text+0x520ff): undefined reference to `clk_disable'
i2c-designware.c:(.devinit.text+0x52108): undefined reference to `clk_put'
Because this new driver uses the clk_*() facilities which is an
ARM-only thing currently.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The i2c Linux driver for the DesignWare i2c block of Synopsys, which is meant
for AMBA Peripheral Bus. This i2c block is used on SoC chips like the ARM9
based PVG610.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
When a process tries to read/write a disconnected i2c device, it receives a signal (e.g. ctrl-c) and the kernel gets stuck.
BUG: soft lockup - CPU#0 stuck for 61s! [I2CEEpromTest:392]
NIP: c01628f8 LR: c01628f0 CTR: c00177cc
REGS: c39abd70 TRAP: 0901 Not tainted (2.6.25.7-alcore)
MSR: 00009032 <EE,ME,IR,DR> CR: 42042048 XER: 20000000
TASK = c3889bd0[392] 'I2CEEpromTest' THREAD: c39aa000
GPR00: 00009000 c39abe20 c3889bd0 c39075c8 c39abe28 00000001 00000000 00000001
GPR08: c3889bd0 c39075c8 00009032 c39abe34 00002437
NIP [c01628f8] cpm_i2c_xfer+0x5fc/0x6d0
LR [c01628f0] cpm_i2c_xfer+0x5f4/0x6d0
Call Trace:
[c39abe20] [c0162924] cpm_i2c_xfer+0x628/0x6d0 (unreliable)
[c39abe90] [c015f6a0] i2c_transfer+0x88/0xb4
[c39abeb0] [c0160164] i2c_master_recv+0x48/0x6c
[c39abed0] [c01618dc] i2cdev_read+0x50/0xe4
[c39abef0] [c0068b24] vfs_read+0xc4/0x108
[c39abf10] [c0068f4c] sys_read+0x4c/0x90
[c39abf40] [c000d348] ret_from_syscall+0x0/0x38
Instruction dump:
3bc00064 92610010 3bf201c8 92810014 3b61
This happen because though the wait_event_interruptible_timeout takes the
signals into account, the driver does not handle them.
We propose to change the wait_event_interruptible_timeout with
wait_event_timeout, leaving the signals to be handled in other points
on the upper layers.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Acked-by: Jochen Friedrich <jochen@scram.de>
[ben-linux@fluff.org: fix title for patch]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Hi Ben,
Can you please queue this fix?
Thanks,
Tony
>From ffe2b2cdf6283770b70a197e3748c6b40a1006be Mon Sep 17 00:00:00 2001
From: Tony Lindgren <tony@atomide.com>
Date: Wed, 17 Jun 2009 13:14:23 +0300
Subject: [PATCH] i2c-omap: Fix build breaking typo in cpu_is_omap_2430
Commit 84bf2c86 introduced a typo, it should be cpu_is_omap2430
instead. The typo was probably caused by a mismerge.
Without this patch all omaps fail to build with:
error: implicit declaration of function 'cpu_is_omap_2430'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: New macro to initialize i2c address lists on the fly
i2c: Don't advertise i2c functions when not available
i2c: Use rwsem instead of mutex for board info
i2c: Add a sysfs interface to instantiate devices
i2c: Limit core locking to the necessary sections
i2c: Kill the redundant client list
i2c: Kill is_newstyle_driver
i2c: Merge i2c_attach_client into i2c_new_device
i2c: Drop i2c_probe function
i2c: Get rid of the legacy binding model
i2c: Kill client_register and client_unregister methods
By using rwsem we can easily manage recursive calls of
i2c_scan_static_board_info() function without breaking the locking.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a sysfs interface to instantiate and delete I2C devices. This is
primarily a replacement of the force_* module parameters implemented
by some i2c drivers. These module parameters were implemented
internally by the I2C_CLIENT_INSMOD* macros, which don't scale well.
This can also be used when developing a driver on a self-soldered
board which doesn't yet have proper I2C device declaration at the
platform level, and presumably for various debugging situations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The i2c-core code tends to hold the core lock for longer than it
should. Limit locking to the necessary sections for both performance
and clarity. This is also a requirement to support I2C multiplexers in
the future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Brownell <dbrownell@users.sourceforge.net>
We used to maintain our own per-adapter list of i2c clients, but this
is redundant with what the driver core does, and no longer needed.
Just drop the redundant list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Legacy i2c drivers are gone, all drivers are new-style now, so there
is no point to check.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Now that i2c_attach_client is no longer exported, it doesn't need to
be a separate function. Merge it into its only user, i2c_new_device.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The legacy i2c_probe() function has no users left, get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
We converted all the legacy i2c drivers so we can finally get rid of
the legacy binding model. Hooray!
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
These methods were useful in the legacy binding model but no longer in
the new (standard) binding model. There are no users left so we can
drop them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the stu300 driver for the ST Micro ST DDC I2C bus
driver depend on MACH_U300, new platforms reusing this I2C
driver will need to add in a similar dependency.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[ben-linux@fluff.org: re-aranged subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This replace all instances in the i2c busses tree of
res->end - res->start + 1 with the handy macro resource_size(res)
from ioport.h (coming in from platform_device.h).
This was created with a simple
sed -i -e 's/\([a-z]*\)->end *- *[a-z]*->start *+ *1/resource_size(\1)/g'
Then manually replacing the PXA redefiniton of the same kind
of macro manually. Recompiled some ARM defconfigs I could find to
make a rough test so it shouldn't break anything, though I
couldn't see exactly which configs you need for all the drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This adds support for the ST Microelectronics DDC I2C bus
driver. This bus is used in the U300 architecture recently
added to RMK:s ARM tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Jean Delvare <khali@linus-fr.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Rather than relying on some of the headers implicitly pulling in io.h,
pull it in explicitly our self for ioremap() and friends.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
therm_windtunnel: Convert to a new-style i2c driver
therm_adt746x: Convert to a new-style i2c driver
windfarm: Convert to new-style i2c drivers
therm_pm72: Convert to a new-style i2c driver
i2c-viapro: Add new PCI device ID for VX855
i2c/chips: Move max6875 to drivers/misc/eeprom
i2c: Do not give adapters a default parent
i2c: Do not probe for TV chips on Voodoo3 adapters
i2c: Retry automatically on arbitration loss
i2c: Remove void casts
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The south bridge of the VIA VX855 chipset has a different PCI Device ID
so i2c-viapro.c needs to be updated with this.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This driver only reads the user EEPROM of that chip, so we can move it
to the eeprom-directory in order to further clean up (and later remove)
drivers/i2c/chips.
The Kconfig text was updated to match the current functionality,
dropping the meanwhile obsoleted parts.
Defconfigs have been adapted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We don't need to give adapters a parent if they don't have one. The
driver core will put them in the virtual device directory and all will
be fine.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
There's no point in giving the I2C bus of Voodoo3 adapters a class
value, there's no video chip driver checking for it anymore. If
support is ever needed, the video device should be instantiated
explicitly rather than probed.
To the best of my knowledge the only video chip that can be found on
these boards is a BT869 video encoder, for which no support exists
currently.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Some small changes in i2c core to retry i2c xfers until either the
maximum number of retries or the timeout is hit.
Signed-off-by: Clifford Wolf <clifford@clifford.at>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
There is sometimes a need for the ocores driver to add devices to the
bus when installed.
i2c_register_board_info can not always be used, because the I2C devices
are not known at an early state, they could for instance be connected
on a I2C bus on a PCI device which has the Open Cores IP.
i2c_new_device can not be used in all cases either since the resulting
bus nummer might be unknown.
The solution is the pass a list of I2C devices in the platform data to
the Open Cores driver. This is useful for MFD drivers.
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sonasath, Moiz