Commit Graph

399 Commits

Author SHA1 Message Date
Hans de Goede 123dfdbcfa phy-sun4i-usb: Add support for the usb-phys on the sun8i-a23 SoC
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25 15:45:47 +05:30
Hans de Goede 2846469631 phy-sun4i-usb: Swap check for disconnect threshold
Before this commit the code for determining the disconnect threshold was
checking for "allwinner,sun4i-a10-usb-phy" or "allwinner,sun6i-a31-usb-phy"
assuming that those where the exception and then newer SoCs would use a
disconnect threshold of 2 like sun7i does. But it turns out that newer
SoCs use a disconnect threshold of 3 and sun5i and sun7i are the
exceptions, so check for those instead.

Here are the settings from the various Allwinner SDK sources:
 sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun8i-h3:  USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);

Note this commit makes no functional changes as currently we only support
sun4i - sun7i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25 15:45:47 +05:30
Hans de Goede 1a52abe682 phy-sun4i-usb: Add extcon support for the otg phy (phy0)
The sunxi musb glue needs to know if a host or normal usb cable is plugged
in, add extcon support so that the musb glue can monitor the host status.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25 15:45:47 +05:30
Hans de Goede d2332303ef phy-sun4i-usb: Add id and vbus detection support for the otg phy (phy0)
The usb0 phy is connected to an OTG controller, and as such needs some special
handling:

1) It allows explicit control over the pullups, enable these on phy_init and
disable them on phy_exit.

2) It has bits to signal id and vbus detect to the musb-core, add support for
for monitoring id and vbus detect gpio-s for use in dual role mode, and set
these bits to the correct values for operating in host only mode when no
gpios are specified in the devicetree.

While updating the devicetree binding documentation also add documentation
for the sofar undocumented usage of regulators for vbus for all 3 phys.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25 15:45:47 +05:30
Joachim Eastwood cbf919bd32 phy: add lpc18xx usb otg phy driver
Add PHY driver for the internal USB OTG PHY found on NXP
LPC18xx and LPC43xx devices. This driver takes care of
enabling the PHY in CREG (syscon) and setting the required
clock frequency.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-25 15:45:46 +05:30
Thomas Hebb dcb54fcb34 phy: berlin-usb: fix divider for BG2
The USB PLL divider set by the marvell,berlin2-usb-phy compatible is not
correct for BG2. We couldn't change it before because BG2Q incorrectly
used the same compatible string. Now that BG2Q's compatible is fixed,
change BG2's divider to the correct value.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Tested-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-15 20:02:09 +05:30
Thomas Hebb 96696a9df9 phy: berlin-usb: fix divider for BG2CD
The marvell,berlin2cd-usb-phy compatible incorrectly sets the PLL
divider to BG2's value instead of BG2CD/BG2Q's. Change it to the right
value.

Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-15 20:02:09 +05:30
Sebastian Ott 1c4b1d1da3 phy/pxa: add HAS_IOMEM dependency
Fix this compile error:

drivers/built-in.o: In function 'mv_usb2_phy_probe':
phy-pxa-28nm-usb2.c:(.text+0x25ec): undefined reference to
'devm_ioremap_resource'
drivers/built-in.o: In function 'mv_hsic_phy_probe':
phy-pxa-28nm-hsic.c:(.text+0x3084): undefined reference to
'devm_ioremap_resource'

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-15 20:02:09 +05:30
Roger Quadros 0a0830feb2 phy: ti-pipe3: fix suspend
Relying on PM-ops for shutting down PHY clocks was a
bad idea since the users (e.g. PCIe/SATA) might not
have been suspended by then.

The main culprit for not shutting down the clocks was
the stray pm_runtime_get() call in probe.

Fix the whole thing in the right way by getting rid
of that pm_runtime_get() call from probe and
removing all PM-ops. It is the sole responsibility
of the PHY user to properly turn OFF and de-initialize
the PHY as part of its suspend routine.

As PHY core serializes init/exit we don't need
to use a spinlock in this driver. So get rid of it.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-07-15 20:02:09 +05:30
Uwe Kleine-König 8e71c68074 phy: tusb1210: make better use of gpiod API
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Furthermore there is devm_gpiod_get_optional which is designed to get
optional gpios.

Simplify driver accordingly.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
2015-07-06 10:10:22 +02:00
Linus Torvalds 78c10e556e Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:

 - Improvements to the tlb_dump code
 - KVM fixes
 - Add support for appended DTB
 - Minor improvements to the R12000 support
 - Minor improvements to the R12000 support
 - Various platform improvments for BCM47xx
 - The usual pile of minor cleanups
 - A number of BPF fixes and improvments
 - Some improvments to the support for R3000 and DECstations
 - Some improvments to the ATH79 platform support
 - A major patchset for the JZ4740 SOC adding support for the CI20 platform
 - Add support for the Pistachio SOC
 - Minor BMIPS/BCM63xx platform support improvments.
 - Avoid "SYNC 0" as memory barrier when unlocking spinlocks
 - Add support for the XWR-1750 board.
 - Paul's __cpuinit/__cpuinitdata cleanups.
 - New Malta CPU board support large memory so enable ZONE_DMA32.

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
  MIPS: spinlock: Adjust arch_spin_lock back-off time
  MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
  MIPS: BCM47xx: Simplify handling SPROM revisions
  MIPS: Cobalt Don't use module_init in non-modular MTD registration.
  MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
  MIPS: use for_each_sg()
  MIPS: BCM47xx: Don't select BCMA_HOST_PCI
  MIPS: BCM47xx: Add helper variable for storing NVRAM length
  MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
  MIPS: Replace smp_mb with release barrier function in unlocks.
  MIPS: i8259: DT support
  MIPS: Malta: Basic DT plumbing
  MIPS: include errno.h for ENODEV in mips-cm.h
  MIPS: Define GCR_GIC_STATUS register fields
  MIPS: BPF: Introduce BPF ASM helpers
  MIPS: BPF: Use BPF register names to describe the ABI
  MIPS: BPF: Move register definition to the BPF header
  MIPS: net: BPF: Replace RSIZE with SZREG
  MIPS: BPF: Free up some callee-saved registers
  MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
  ...
2015-06-27 12:44:34 -07:00
Linus Torvalds 2a298679b4 USB patches for 4.2-rc1
Here's the big USB patchset for 4.2-rc1.  As is normal these days, the
 majority of changes are in the gadget drivers, with a bunch of other
 small driver changes.
 
 All of these have been in linux-next with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
 TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
 =hrdz
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB updates from Greg KH:
 "Here's the big USB patchset for 4.2-rc1.  As is normal these days, the
  majority of changes are in the gadget drivers, with a bunch of other
  small driver changes.

  All of these have been in linux-next with no reported issues"

* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
  usb: dwc3: Use ASCII space in Kconfig
  usb: chipidea: add work-around for Marvell HSIC PHY startup
  usb: chipidea: allow multiple instances to use default ci_default_pdata
  dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
  phy: add Marvell HSIC 28nm PHY
  phy: Add Marvell USB 2.0 OTG 28nm PHY
  dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
  USB: ssb: use devm_kzalloc
  USB: ssb: fix error handling in ssb_hcd_create_pdev()
  usb: isp1760: check for null return from kzalloc
  cdc-acm: Add support of ATOL FPrint fiscal printers
  usb: chipidea: usbmisc_imx: Remove unneeded semicolon
  USB: usbtmc: add device quirk for Rigol DS6104
  USB: serial: mos7840: Use setup_timer
  phy: twl4030-usb: add ABI documentation
  phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
  phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
  phy: twl4030-usb: make runtime pm more reliable.
  drivers:usb:fsl: Fix compilation error for fsl ehci drv
  usb: renesas_usbhs: Don't disable the pipe if Control write status stage
  ...
2015-06-26 15:59:26 -07:00
Pratyush Anand 9c5dcdd0c7 Mohit Kumar has moved
Mohit's email-id doesn't exist anymore as he has left the company.
Replace ST's id with mohit.kumar.dhaka@gmail.com.

Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Mohit Kumar <mohit.kumar.dhaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-06-25 17:00:38 -07:00
Pratyush Anand e34cadde3b Pratyush Anand has moved
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company.  Replace ST's id with pratyush.anand@gmail.com.

Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-06-25 17:00:38 -07:00
Andrew Bresticker 57991ebaf9 PHY: Add driver for Pistachio USB2.0 PHY
Add a driver for the USB2.0 PHY found on the IMG Pistachio SoC.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2015-06-21 21:53:38 +02:00
Rob Herring 10d9029bcb phy: add Marvell HSIC 28nm PHY
Add PHY driver for the Marvell HSIC 28nm PHY. This PHY is found in PXA1928
SOC.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-09 12:20:30 -07:00
Rob Herring 603c5f9d9c phy: Add Marvell USB 2.0 OTG 28nm PHY
Add driver for USB 28nm PHY found in Marvell PXA1928 SOC.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-09 12:20:30 -07:00
Greg Kroah-Hartman 19915e6234 Merge 4.1-rc7 into usb-next
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-06-08 10:57:51 -07:00
Greg Kroah-Hartman b3d424e3dc phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
 *) new phy API to get PHY by index which is used in EHCI and
    OHCI controller drivers
 *) support specifying supply at port level used for multi-port PHYs
 *) sparse warning fixes in miphy PHYs
 *) fix pm_runtime issues in twl4030 driver
 
 Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJVbbvfAAoJEA5ceFyATYLZdAIP/2mFENq9DIRDqU7LV4aQRDlC
 TlL+DLGwElAGKkq7bL3UaWy+10kooTmVaYVB1MACAPXZgKguTkjsSdWXDSxFHDyG
 tq32CqkeMx1uhsZBMhdxsIsTnAPfEo1s2lO7O/HaJTq38aqKixC5+A3IYXttSvET
 jF4XCx7IGNK7YIMylTzAW1FN9rHvsp4RRKIkPjS8EAiAbQIcu7rxKdSbfwJ69Zxt
 EUep3u7jvlQK6SmOig3nkoQFf70G6d7p0VsBPrU6l6Dg9Ciu/5ZvzCkg5ukGotOl
 1GIpowjW3abIaX6yGOD95phU8+JPZbncG/vrQ5Hf/FDZtvCgs6tYqY+Zqmxf7SlK
 4Jj43+sjvDt05Ty9K1sP2FnQqBq9XKEmX5K1pYCrHDbDiH0L9gKeX9/46dJhDrMS
 F3rfrcgBxqBqT96BsqPHmuN0uUvXaF7pGKyFWoGodblBsYee6z4XAl8Up62Lqq3U
 QglegTz9ICKDU1j8xmjLHN9l21BfXANdirFTyjtV3XIGR6mcmzd3R3qk7x2ulaQ8
 lA4gfUhm9X8f55FTqLIw+7Ld+rgEW9NYHSX4fFvtzB/T5SPdOrslgjby4i0a81Pv
 IfQcLaQZ75QIj+22sy27cXrQsmUCe6sNXrms190uknh3hEHDeNOtPupYIMJcXiO+
 n2YJ6QCOnly3tSMFNWfM
 =vPk6
 -----END PGP SIGNATURE-----

Merge tag 'phy-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.2 merge window

*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
   OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-06-03 14:13:41 +09:00
NeilBrown 4724e27114 phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
The USB phy should initialize with power-off, and will be powered on
by the USB system when a cable connection is detected.

Having this pm_runtime_get_sync() during probe causes the phy to
*always* be powered on.
Removing it returns to sensible power management.

Fixes: 96be39ab34
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-06-01 16:08:24 +05:30
NeilBrown 186ecebeb6 phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
When the runtime_suspend callback is running, 'runtime_status'
is always RPM_SUSPENDING, so pm_runtime_suspended() will always
fail.
Similarly while the runtime_resume callback is running
'runtime_status' is RPM_RESUMING, so pm_runtime_active() will
always fail.

So remove these two pointless tests.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-06-01 16:08:24 +05:30
NeilBrown 56301df6bc phy: twl4030-usb: make runtime pm more reliable.
A construct like:

        if (pm_runtime_suspended(twl->dev))
               pm_runtime_get_sync(twl->dev);

is against the spirit of the runtime_pm interface as it
makes the internal refcounting useless.

In this case it is also racy, particularly as 'put_autosuspend'
is used to drop a reference.
When that happens a timer is started and the device is
runtime-suspended after the timeout.
If the above code runs in this window, the device will not be
found to be suspended so no pm_runtime reference is taken.
When the timer expires the device will be suspended, which is
against the intention of the code.

So be more direct is taking and dropping references.
If twl->linkstat is VBUS_VALID or ID_GROUND, then hold a
pm_runtime reference, otherwise don't.
Define "cable_present()" to test for this condition.

Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-06-01 16:08:24 +05:30
Hans de Goede 24fe86a617 phy: sun4i-usb: Add a sunxi specific function for setting squelch-detect
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.

The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.

Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-27 12:20:36 -05:00
Brian Norris 0d486806ff phy: add Broadcom SATA3 PHY driver for Broadcom STB SoCs
Supports up to two ports which can each be powered on/off and configured
independently.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-22 16:53:09 +05:30
Yoshihiro Shimoda 9d699bf4db phy: rcar-gen2: Add support for R-Car E2
This patch adds a compatible string to support for R-Car E2.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-21 18:35:08 +05:30
Heikki Krogerus 1c14905ef9 phy: add driver for TI TUSB1210 ULPI PHY
TUSB1210 ULPI PHY has vendor specific register for eye
diagram tuning. On some platforms the system firmware has
set optimized value to it. In order to not loose the
optimized value, the driver stores it during probe and
restores it every time the PHY is powered back on.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 12:07:01 -05:00
Heikki Krogerus 723487a6ff phy: helpers for USB ULPI PHY registering
ULPI PHYs need to be bound to their controllers with a
lookup. This adds helpers that the ULPI drivers can use to
do both, the registration of the PHY and the lookup, at the
same time.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2015-05-13 12:06:56 -05:00
Yoshihiro Shimoda a3ac3d4a29 phy: phy-rcar-gen2: Fix USBHS_UGSTS_LOCK value
According to the technical update (No. TN-RCS-B011A/E), the UGSTS LOCK
bit location is bit 8, not bits 1 and 0. It also says that the register
address offset of UGSTS is 0x88, not 0x90.
So, this patch fixes the USBHS_UGSTS_LOCK value and some comments.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-12 20:57:19 +05:30
Kishon Vijay Abraham I 4581f798ec phy: omap-usb2: invoke pm_runtime_disable on error path
if devm_clk_get for wkupclk fails, there will be an unbalanced
pm_runtime_enable. Fix it here.

Reported-by: Benoit Parrot <bparrot@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-12 20:57:19 +05:30
Felipe Balbi 7f7a4d306f phy: fix Kconfig dependencies
DM816x PHY uses usb_phy_* methods and because
of that, it must select USB_PHY, however, because
the drivers in question (DM816x, TWL4030 and
OMAP_USB2) sit outside of drivers/usb/ directory,
meaning they can be built even if USB_SUPPORT=n.

This patches fixes the dependencies by adding
USB_SUPPORT as a dependency and making all drivers
select USB_PHY (which cannot be selected through
menuconfig).

Note that this fixes some linking breakages when
building with randconfig.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-12 20:57:18 +05:30
Stephen Boyd 4d051f74cb phy: qcom-ufs: Switch dependency to ARCH_QCOM
This phy only exists on platforms under ARCH_QCOM, not ARCH_MSM.

Cc: Yaniv Gardi <ygardi@codeaurora.org>
Cc: Dov Levenglick <dovl@codeaurora.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-12 20:52:13 +05:30
Axel Lin 33f434d283 phy: core: Check requested PHY status in _of_phy_get()
This is a common checking in various drivers, so move the checking to
_of_phy_get().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 21:42:27 +05:30
Felipe Balbi 5bea496820 phy: miphy365x: fix sparse warnings
Add missing 'static' modifier so sparse
won't complain anymore.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 21:42:26 +05:30
Felipe Balbi 99db11c6e8 phy: miphy28lp: fix sparse warnings
Add missing __iomem annotation to the base address
so Sparse doesn't complain.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 21:42:26 +05:30
Dmitry Torokhov 87006dd600 phy: phy-core: allow specifying supply at port level
Multi-port phys may have per port power supplies. Let's change phy
core to look for supply at the port level when multiple ports are
specified. To keep compatibility with the existing device tree board
descriptions for single-port phys we will continue looking up the
power supply at the parent node level

Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 21:42:25 +05:30
Arun Ramamurthy 6be109b31c phy: core: Add devm_of_phy_get_by_index to phy-core
Some generic drivers, such as ehci, may use multiple phys and for such
drivers referencing phy(s) by name(s) does not make sense. Instead of
inventing new naming schemes and using custom code to iterate through them,
such drivers are better of using nameless phy bindings and using this newly
introduced API to iterate through them.

Signed-off-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
[kishon@ti.com: fix compilation errors]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 21:42:23 +05:30
Axel Lin f83be4c3f6 phy: core: Fix error checking in (devm_)phy_optional_get
Don't pass valid pointer to PTR_ERR, use PTR_ERR(phy) only when
IS_ERR(phy) is true.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-05-11 20:18:51 +05:30
Linus Torvalds 42e3a58b02 USB patches for 4.1-rc1
Here's the big USB (and PHY) driver patchset for 4.1-rc1.
 
 Everything here has been in linux-next, and the full details are below
 in the shortlog.  Nothing major, just the normal round of new
 drivers,api updates, and other changes, mostly in the USB gadget area,
 as usual.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlUsHXYACgkQMUfUDdst+ykGvwCfbI3z0VYJqyvPi7pbn+jtGouQ
 E7MAoICdP90ofZfyzQzXy+2xKTTCiP5L
 =jSjh
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB driver updates from Greg KH:
 "Here's the big USB (and PHY) driver patchset for 4.1-rc1.

  Everything here has been in linux-next, and the full details are below
  in the shortlog.  Nothing major, just the normal round of new
  drivers,api updates, and other changes, mostly in the USB gadget area,
  as usual"

* tag 'usb-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (252 commits)
  drivers/usb/core: devio.c: Removed an uneeded space before tab
  usb: dwc2: host: sleep USB_RESUME_TIMEOUT during resume
  usb: chipidea: debug: add low power mode check before print registers
  usb: chipidea: udc: bypass pullup DP when gadget connect in OTG fsm mode
  usb: core: hub: use new USB_RESUME_TIMEOUT
  usb: isp1760: hcd: use new USB_RESUME_TIMEOUT
  usb: dwc2: hcd: use new USB_RESUME_TIMEOUT
  usb: host: sl811: use new USB_RESUME_TIMEOUT
  usb: host: r8a66597: use new USB_RESUME_TIMEOUT
  usb: host: oxu210hp: use new USB_RESUME_TIMEOUT
  usb: host: fusbh200: use new USB_RESUME_TIMEOUT
  usb: host: fotg210: use new USB_RESUME_TIMEOUT
  usb: host: isp116x: use new USB_RESUME_TIMEOUT
  usb: musb: use new USB_RESUME_TIMEOUT
  usb: host: uhci: use new USB_RESUME_TIMEOUT
  usb: host: ehci: use new USB_RESUME_TIMEOUT
  usb: host: xhci: use new USB_RESUME_TIMEOUT
  usb: define a generic USB_RESUME_TIMEOUT macro
  usb: musb: dsps: fix build on i386 when COMPILE_TEST is set
  ehci-hub: use USB_DT_HUB
  ...
2015-04-13 17:07:21 -07:00
Mark Brown bea3672833 Merge remote-tracking branches 'regulator/topic/mode', 'regulator/topic/notifier', 'regulator/topic/palmas', 'regulator/topic/qcom' and 'regulator/topic/stw481x' into regulator-next 2015-04-10 19:16:03 +01:00
Greg Kroah-Hartman 2aebe3f3b2 New Features
============
 *) Add driver for USB PHYs on sun9i
 *) Add driver for USB PHY on dm816x
 *) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC
 
 Fixes
 =====
 *) Fix power_on/power_off failure paths in some drivers
 *) Make miphy365x use generic PHY type constants
 *) Fix build errors due to missing export symbols in qcom-ufs driver
 *) Make all the functions return proper error values
 
 Cleanups
 ========
 *) use PTR_ERR_OR_ZERO to simplify code
 *) use devm_kcalloc instead of devm_kzalloc with multiply
 *) remove un-necessary ifdef CONFIG_OF
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJVHrrMAAoJEA5ceFyATYLZV8kP/074teM4HZMAqmUVRG+nRr8b
 Eb8QYOzpnazUKtUovMYePzLjIZ3kvlMepSVVZiZqP6Uc2s6bnhTUN758HZBTdMVO
 Cer63lcp5eM6yBSIL4kNo3+18ikql3LJK9kQZoLGszZmVJzwwqhL/cWxl8+WfZ+P
 U71ciL07xmQD1c1GbRsuDBykaDKnf4M9HVUzP9w/pFANKYWWHdR3bj53kz9W7bGm
 gF/6wVFfxkknPfQjlqo9VUoSPN3P+WIcoM2rPG1b1u2adAAKFSYvXX2eJKWZF6Cz
 L9IZn1bTB0tMkrbswpMRqPtKjfmGyi1Acx8jt8WVA5pjNZ4K2P+9T7vsWifEnYa/
 BDYdJJRzZSL89m9zwEFvLF490pTJrk33eFbqzHDGmDcdtj8KY8XZ9Fp5R2Lmj26s
 mtST0Pi+j9SGg95KZBcXd2l1EJmdDutEYy7LgVvkLk4IFPfOyaAFEhSNW+Qi+Lh9
 SkDqbZUrk9ZxzsWqYJW5LVbQlscJ2NzQuf5AgkrXsufXO0B8RAV5bt0f88ENmQsJ
 rbbbWIb/ljT6YbZqT8z2X8T0PNZBknSfepb5LO5QAZMMJJm2202TondsISytvC9U
 fS5sBIDzuiiMtOA9FwA5Yl1bPWq6QY4OwqIMX3LAs10ylJhbuqJ7nK5qH3O4bpk+
 DzOCd1oLJhXjnOXIujz2
 =0gB+
 -----END PGP SIGNATURE-----

Merge tag 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

New Features
============
*) Add driver for USB PHYs on sun9i
*) Add driver for USB PHY on dm816x
*) Modified exynos5-usbdrd driver to add support for Exynos5433 SoC

Fixes
=====
*) Fix power_on/power_off failure paths in some drivers
*) Make miphy365x use generic PHY type constants
*) Fix build errors due to missing export symbols in qcom-ufs driver
*) Make all the functions return proper error values

Cleanups
========
*) use PTR_ERR_OR_ZERO to simplify code
*) use devm_kcalloc instead of devm_kzalloc with multiply
*) remove un-necessary ifdef CONFIG_OF
2015-04-10 13:47:50 +02:00
Axel Lin 407ed83574 phy: spear1340-miphy: Return proper error for spear1340_miphy_xlate
The of_xlate callback should return ERR_PTR on error.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:21 +05:30
Axel Lin 247e21c613 phy: spear1310-miphy: Return proper error for spear1310_miphy_xlate
The of_xlate callback should return ERR_PTR on error.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:21 +05:30
Peter Griffin fbea230e78 phy: miphy365x: Use the generic phy type constants in dt-bindings/phy/phy.h
Now there are generic phy type constants declared in phy.h, migrate over to
using them rather than defining our own. This change has been done as one
atomic commit to be bisectable.

Note: The values of the defines are the same, so there is no ABI breakage
with this patch.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:20 +05:30
Chen-Yu Tsai 9c3b443026 phy: Add driver to support individual USB PHYs on sun9i
Unlike previous Allwinner SoCs, there is no central PHY control block
on the A80. Also, OTG support is completely split off into a different
controller.

This adds a new driver to support the regular USB PHYs.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:19 +05:30
Tony Lindgren 609adde838 phy: Add a driver for dm816x USB PHY
Add a minimal driver for dm816x USB. This makes USB work on dm816x
without any other changes needed as it can use the existing musb_dsps
glue layer for the USB controller.

Note that this phy is different from dm814x and am335x.

Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:19 +05:30
Axel Lin 52ea796b91 phy: qcom-ufs: Don't return error if fail to get optional resource
"dev_ref_clk_ctrl_mem" is optional resource, so don't return error if fail to
get the resource. Since it's an optional resource, don't emit error if
fail to get dev_ref_clk_ctrl_mem.

Also remove redundant test for res, it's done by devm_ioremap_resource().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:18 +05:30
Axel Lin 358d6c87e7 phy: qcom-ufs: Fix build error due to missing export symbols
Fix below build error when compile the driver as a module.

ERROR: "ufs_qcom_phy_power_off" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_power_on" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_exit" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_calibrate" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_generic_probe" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_init_vregulators" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_init_clks" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_remove" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "get_ufs_qcom_phy" [drivers/phy/phy-qcom-ufs-qmp-20nm.ko] undefined!
ERROR: "ufs_qcom_phy_power_off" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_power_on" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_exit" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_generic_probe" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_init_vregulators" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_init_clks" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_calibrate" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "ufs_qcom_phy_remove" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
ERROR: "get_ufs_qcom_phy" [drivers/phy/phy-qcom-ufs-qmp-14nm.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-04-03 18:16:18 +05:30
Axel Lin 7a504c935e phy: samsung_usb2: Fixup samsung_usb2_phy_power_on/off paths
Ensure we have balanced clk_prepare_enable/clk_disable_unprepare calls if
.power_on or .power_off callbacks return error.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-26 05:06:10 +05:30
Jaewon Kim 2be608561a phy: exynos5-usbdrd: Add to support for Exynos5433 SoC
This patch adds driver data to support for Exynos5433 SoC.
The Exynos5433 has one USB3.0 Host and USB3.0 DRD(Dual Role Device).
Exynos5433 is simplar to Eyxnos7 but Exynos5433 have
one more USB3.0 Host controller.

Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-26 05:06:10 +05:30
Axel Lin d89a7f69d6 phy: qcom-ufs: Catch devm_phy_create failure in ufs_qcom_phy_generic_probe
Current code does NULL test against return value of ufs_qcom_phy_generic_probe.
However, in the case of devm_phy_create() failure, ufs_qcom_phy_generic_probe
does not return NULL. Fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-26 05:06:09 +05:30
Axel Lin 080de5ba39 phy: stih41x-usb: Fixup stih41x_usb_phy_power_on failure path
If stih41x_usb_phy_power_on() fails, we need to call clk_disable_unprepare()
before return error. This is to ensure we have balanced clk_enable/disable
calls.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-26 05:06:09 +05:30
Axel Lin b1ff3231b2 phy: omap-usb2: Fix missing clk_prepare call when using old dt name
Current code does not call clk_prepare(phy->optclk) when using the old
usb_otg_ss_refclk960m name. Fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:39 +05:30
Axel Lin dd64ad387c phy: ti/omap: Fix modalias
Remove extra space in MODULE_ALIAS.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:38 +05:30
Axel Lin 736b67a320 phy: core: Fixup return value of phy_exit when !pm_runtime_enabled
When phy_pm_runtime_get_sync() returns -ENOTSUPP, phy_exit() also returns
-ENOTSUPP if !phy->ops->exit. Fix it.
Also move the code to override ret close to the code we got ret.
I think it is less error prone this way.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:38 +05:30
Axel Lin 018e6ff3c0 phy: miphy28lp: Convert to devm_kcalloc and fix wrong sizof
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:37 +05:30
Axel Lin d8d52948a0 phy: miphy365x: Convert to devm_kcalloc and fix wrong sizeof
Prefer devm_kcalloc over devm_kzalloc with multiply.
In additional, use sizeof(phy) is incorrect, fix it.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:37 +05:30
Axel Lin 8f27f167de phy: twl4030-usb: Remove redundant assignment for twl->linkstat
It's pointless to set twl->linkstat twice.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:36 +05:30
Axel Lin ecd5fb026d phy: exynos5-usbdrd: Fix off-by-one valid value checking for args->args[0]
Current code uses args->args[0] as array subscript of phy_drd->phys[].
So the valid value range for args->args[0] is 0 ... EXYNOS5_DRDPHYS_NUM - 1.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:14:36 +05:30
Thierry Reding 2f1bce487c phy: Find the right match in devm_phy_destroy()
devm_phy_create() stores the pointer to the new PHY at the address
returned by devres_alloc(). The res parameter passed to devm_phy_match()
is therefore the location where the pointer to the PHY is stored, hence
it needs to be dereferenced before comparing to the match data in order
to find the correct match.

Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-13 17:13:52 +05:30
Axel Lin 6b08e36ba3 phy: rockchip-usb: Fixup rockchip_usb_phy_power_on failure path
If rockchip_usb_phy_power() fails, we need to call clk_disable_unprepare()
before return. This is to ensure we have balanced clk_enable/disable calls.
Also remove unneeded ret checking in rockchip_usb_phy_power_off.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-12 11:01:17 +05:30
Axel Lin a5e5d3c0b2 phy: ti-pipe3: Simplify ti_pipe3_dpll_wait_lock implementation
Code simplification. No functional change.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-12 11:01:17 +05:30
Axel Lin bd4abc2f96 phy: samsung-usb2: Remove NULL terminating entry from phys array
Current code uses num_phys settings to tell the number of entries in phys.
Thus remove the NULL terminating entry from phys array which is not necessary.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-12 11:01:16 +05:30
Axel Lin 1cbdfc48c3 phy: hix5hd2-sata: Check return value of platform_get_resource
This prevent NULL pointer dereference if res is NULL.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-12 11:01:16 +05:30
Axel Lin 0f9722e37f phy: exynos-dp-video: Kill exynos_dp_video_phy_pwr_isol function
If IS_ERR(state->regs) the .probe fails.
So IS_ERR(state->regs) test in exynos_dp_video_phy_pwr_isol() is not necessary.
exynos_dp_video_phy_pwr_isol() simply does a regmap_update_bits() call now,
just call regmap_update_bits() instead and return proper return value.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-12 11:01:15 +05:30
Axel Lin af69decc7c phy: exynos-mipi-video: Use spin_lock to protct state->regmap rmw operations
The state->regmap is initialized by devm_regmap_init_mmio().
So it's fine to use spin_lock rather than mutex to protct state->regmap rmw
operations.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[Julia.Lawall@lip6.fr: Found an issue with the original patch w.r.t unbalanced
 spin_lock call]
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-11 15:51:06 +05:30
Axel Lin 739ae3452d phy: berlin-usb: Set drvdata for phy and use it
At the context where we have pointer to struct phy, it's useful to call
phy_get_drvdata() to get the address of priv. With this change, we can
remove the to_phy_berlin_usb_priv() macro and remove *phy from struct
phy_berlin_usb_priv.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 17:18:09 +05:30
Stephen Rothwell 7e476c7dd8 regulator: fixes for regulator_set_optimum_mode name change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
2015-03-10 10:39:32 +00:00
Axel Lin 298fe56ee2 phy: ti-pipe3: Remove unneeded ifdef CONFIG_OF guard and of_match_ptr
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:28 +05:30
Axel Lin 52a4a72a1a phy: omap-usb2: Remove unneeded ifdef CONFIG_OF guard and of_match_ptr
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin 1f9ba767d5 phy: omap-control: Remove unneeded ifdef CONFIG_OF guard and of_match_ptr
if !CONFIG_OF, the probe fails.
This is a dt-only driver, so the ifdef CONFIG_OF guard and of_match_ptr are
not needed.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin 320c3fcec6 phy: miphy28lp: Use PTR_ERR_OR_ZERO
PTR_ERR_OR_ZERO simplifies the code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gabriel Fernandez<gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin f8f55393b2 phy: berlin-sata: Use devm_kcalloc at appropriate place
Prefer devm_kcalloc over devm_kzalloc with multiply.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin 8fd0ea395f phy: xgene: Use PTR_ERR_OR_ZERO
Also remove unneeded goto and rc variable.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin 82ffb676c8 phy: berlin-usb: Use PTR_ERR_OR_ZERO
PTR_ERR_OR_ZERO simplifies the code.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-10 14:12:27 +05:30
Axel Lin cfd565d1e1 phy: exynos-mipi-video: Fixup the test for state->regmap
syscon_regmap_lookup_by_phandle() returns ERR_PTR on error.
Thus don't use null test against state->regmap.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:48 +05:30
Axel Lin 235b633eb5 phy: miphy28lp: Add missing .owner field in miphy28lp_ops
Add missing .owner field in miphy28lp_ops, which is used for refcounting.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:47 +05:30
Axel Lin 991e45f8f8 phy: xgene: Remove duplicate code to set ctx->dev
Set it once is enough and it's done after devm_kzalloc().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:47 +05:30
Axel Lin 7a83b145b5 phy: armada375-usb2: Set drvdata for phy and use it
At the context we have pointer to struct phy, it's useful to call
phy_get_drvdata() to get the address of cluster_phy. This has slightly
better readability than calling dev_get_drvdata(phy->dev.parent).

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:47 +05:30
Axel Lin 5bd568f5d2 phy: miphy365x: Avoid calling of_get_child_count() multiple times
Currently, of_get_child_count() is called in each iteration of the for loop in
miphy365x_xlate(). This patch stores the return value of of_get_child_count()
in miphy_dev->nphys and call of_get_child_count() once in miphy365x_probe().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:47 +05:30
Axel Lin 21647f7383 phy: miphy28lp: Avoid calling of_get_child_count() multiple times
Currently, of_get_child_count() is called in each iteration of the for loop in
miphy28lp_xlate(). This patch stores the return value of of_get_child_count()
in miphy_dev->nphys and call of_get_child_count() once in miphy28lp_probe().

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-03-04 18:31:47 +05:30
Linus Torvalds e29876723f USB patches for 3.20-rc1
Here's the big pull request for the USB driver tree for 3.20-rc1.
 
 Nothing major happening here, just lots of gadget driver updates, new
 device ids, and a bunch of cleanups.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlTgtrcACgkQMUfUDdst+yn0tACgygJPNvu1l3ukNJCCpWuOErIj
 3KsAnjiEXv90DLYJiVLJ4EbLPw0V9wAv
 =DrJx
 -----END PGP SIGNATURE-----

Merge tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB patches from Greg KH:
 "Here's the big pull request for the USB driver tree for 3.20-rc1.

  Nothing major happening here, just lots of gadget driver updates, new
  device ids, and a bunch of cleanups.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
  usb: musb: fix device hotplug behind hub
  usb: dwc2: Fix a bug in reading the endpoint directions from reg.
  staging: emxx_udc: fix the build error
  usb: Retry port status check on resume to work around RH bugs
  Revert "usb: Reset USB-3 devices on USB-3 link bounce"
  uhci-hub: use HUB_CHAR_*
  usb: kconfig: replace PPC_OF with PPC
  ehci-pci: disable for Intel MID platforms (update)
  usb: gadget: Kconfig: use bool instead of boolean
  usb: musb: blackfin: remove incorrect __exit_p()
  USB: fix use-after-free bug in usb_hcd_unlink_urb()
  ehci-pci: disable for Intel MID platforms
  usb: host: pci_quirks: joing string literals
  USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
  USB: usbfs: allow URBs to be reaped after disconnection
  cdc-acm: kill unnecessary messages
  cdc-acm: add sanity checks
  usb: phy: phy-generic: Fix USB PHY gpio reset
  usb: dwc2: fix USB core dependencies
  usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
  ...
2015-02-15 10:24:55 -08:00
Linus Torvalds 540a7c5061 SCSI misc on 20150209
This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
 megaraid_sas, ses) plus an assortment of minor updates.  There's also an
 update to ufs which adds new phy drivers and finally a new logging
 infrastructure for SCSI.
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQEcBAABAgAGBQJU2Ty5AAoJEDeqqVYsXL0M9rAH/1xNpAxXuxQq+dW5Z+uOaX60
 5RRIu7/xA1HEfzkT5FTHrolmogDjVqawu4PZS66iHDeo05RBVUlbTA8qCK+MlRcN
 U6s0cLEw59eH3EaCfOGuYp/MnbhuV0eNxe0btmqJIQwuW3+gwZKGJdOq6LS2YasJ
 k/DyIBVmkJAVsN56vm9q2vbtcZp+Bg+ngqBS+SC4TF7vV1WCtFmS6yaUf62PYW3D
 +Irx37qHZntDR5wdw3dsuKDi5U8bl6myPjaVLnVJqg/WIF9RlCkjk5xpWT99AmVO
 NmtYQxLLBlAQ5K+sIlBUwxZe+8q1l+Aj4TTmJHAfFtyfp25s7JR9I6/QtOyC5Kw=
 =odol
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull first round of SCSI updates from James Bottomley:
 "This is the usual grab bag of driver updates (hpsa, storvsc, mp2sas,
  megaraid_sas, ses) plus an assortment of minor updates.

  There's also an update to ufs which adds new phy drivers and finally a
  new logging infrastructure for SCSI"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (114 commits)
  scsi_logging: return void for dev_printk() functions
  scsi: print single-character strings with seq_putc
  scsi: merge consecutive seq_puts calls
  scsi: replace seq_printf with seq_puts
  aha152x: replace seq_printf with seq_puts
  advansys: replace seq_printf with seq_puts
  scsi: remove SPRINTF macro
  sg: remove an unused variable
  hpsa: Use local workqueues instead of system workqueues
  hpsa: add in P840ar controller model name
  hpsa: add in gen9 controller model names
  hpsa: detect and report failures changing controller transport modes
  hpsa: shorten the wait for the CISS doorbell mode change ack
  hpsa: refactor duplicated scan completion code into a new routine
  hpsa: move SG descriptor set-up out of hpsa_scatter_gather()
  hpsa: do not use function pointers in fast path command submission
  hpsa: print CDBs instead of kernel virtual addresses for uncommon errors
  hpsa: do not use a void pointer for scsi_cmd field of struct CommandList
  hpsa: return failed from device reset/abort handlers
  hpsa: check for ctlr lockup after command allocation in main io path
  ...
2015-02-11 10:28:45 -08:00
Peter Griffin bbd3ce86c7 phy: miphy365x: Pass sysconfig register offsets via syscfg dt property.
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.

This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.

This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
2015-01-30 18:12:05 +05:30
Sylwester Nawrocki e4b3d38088 phy: exynos-video-mipi: Fix regression by adding support for PMU regmap
After the Exynos Power Management Unit (PMU) driver was converted
to the platform device driver in commit 14fc8b93d4
("ARM: EXYNOS: Add platform driver support for Exynos PMU") and
then PMU device nodes added to Exynos4 DTs in commit
7b9613aca4 ("ARM: dts: add PMU syscon node for exynos4")
the mipi video phy driver started failing probing, due to overlapping
memory mapped register region resources.

Now all the Exynos peripheral devices which have registers in the PMU
region are supposed to use the regmap provided by the syscon driver.
So support for regmap is added in this patch, this unfortunately
creates yet another indirection into that supposedly trivial driver.

The additional mutex is required because single register is used by
PHY pairs (they share bit in a register). An improvement here could
be to allow a PHY instance be created with a driver custom mutex,
which would then be common for each PHY pair. This would eliminate
one of 3 mutexes which need to be taken in the phy_power_on/
phy_power_off code path. However, I tried to keep this bug fix patch
possibly simple.

This change is needed to make MIPI DSI displays and MIPI CSI-2
camera sensors working again on Exynos4 boards.

Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-30 16:06:48 +05:30
Yunzhi Li 64d11406de phy: add a driver for the Rockchip SoC internal USB2.0 PHY
This patch to add a generic PHY driver for ROCKCHIP usb PHYs,
currently this driver can support RK3288. The RK3288 SoC have
three independent USB PHY IPs which are all configured through a
set of registers located in the GRF (general register files)
module.

Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-30 16:06:47 +05:30
David S. Miller 95f873f2ff Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	arch/arm/boot/dts/imx6sx-sdb.dts
	net/sched/cls_bpf.c

Two simple sets of overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-27 16:59:56 -08:00
Peter Griffin 5402d927ae phy: phy-stih407-usb: Pass sysconfig register offsets via syscfg property.
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.

This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.

This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.

This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-21 15:23:06 +05:30
Gabriel FERNANDEZ de6e0f84be phy: miphy28lp: Pass sysconfig register offsets via syscfg dt property.
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.

This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.

I have updated the miphy28lp phy driver same way as Peter's implementation.

Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-21 15:23:06 +05:30
Wei Yongjun 147fd9d6bb phy: fix return value check in armada375_usb_phy_probe()
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-21 15:23:06 +05:30
Roger Quadros 7f33912d29 phy: ti-pipe3: Fix SATA across suspend/resume
Failed test case: Boot without SATA drive connected. Suspend/resume
the board and then connect SATA drive. It fails to enumerate.

Due to Errata i783 "SATA Lockup After SATA DPLL Unlock/Relock"
we can't allow SATA DPLL to be in the unlocked state.
The SATA refclk (sata_ref_clk) is the source of the SATA_DPLL.
This clock is being controlled only by the AHCI SATA driver and is
shut off during system suspend (if the SATA drive was not already attached)
causing the SATA DPLL to be unlocked and so causing errata i783.

To prevent sata_ref_clk from being disabled, we add the control of
this clock to the SATA PHY driver and prevent it from being disabled.

This also fixes the issue of SATA not working on OMAP5/DRA7 when
AHCI platform driver is built as a module.

NOTE: Device tree changes also required for OMAP5 & DRA7.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-21 15:23:06 +05:30
Roger Quadros 6e7384320f phy: ti-pipe3: Disable clocks on system suspend
On system suspend, the runtime_suspend() driver hook doesn't get
called for USB phy and so the clocks are not disabled in the driver.
This causes the L3INIT_960M_GFCLK and L3INIT_480M_GFCLK to remain
active on the DRA7 platform while in system suspend.

In case of pcie-phy, the runtime_suspend hook gets called after
the suspend hook so we introduce a flag phy->enabled to keep
track if our clocks are enabled or not to prevent multiple
enable/disables.

Add suspend/resume hooks to the driver.
Move enabling/disabling clock code into helper functions.

Reported-by: Nishant Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2015-01-21 15:23:06 +05:30
Yaniv Gardi ca14ab55fb phy: qcom-ufs: add support for 14nm phy
This change adds a support for a 14nm qcom-ufs phy that is
required in platforms that use ufs-qcom controller.

Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2015-01-20 19:43:26 +01:00
Yaniv Gardi 39e794bff7 phy: qcom-ufs: add support for 20nm phy
This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.

Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2015-01-20 19:43:25 +01:00
Yaniv Gardi adaafaa393 phy: qcom-ufs: add support for QUALCOMM Technologies UFS PHY drivers
This change adds a generic and common API support for ufs phy QUALCOMM
Technologies. This support provides common code and also points
to specific phy callbacks to differentiate between different behaviors
of frequent use-cases (like power on, power off, phy calibration etc).

Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2015-01-20 19:43:24 +01:00
Peter Griffin 63139885c4 phy: miphy365x: Pass sysconfig register offsets via syscfg dt property.
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.

This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.

This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-11 18:53:34 -05:00
Peter Griffin 937127fe13 phy: phy-stih407-usb: Pass sysconfig register offsets via syscfg property.
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.

This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.

This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.

This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-11 18:53:33 -05:00
Vignesh R 0bc09f9cdc phy: phy-ti-pipe3: fix inconsistent enumeration of PCIe gen2 cards
Prior to DRA74x silicon rev 1.1, pcie_pcs register bits 8-15 and bits 16-23
were used to configure RC delay count for phy1 and phy2 respectively.
phyid was used as index to distinguish the phys and to configure the delay
values appropriately.

As of DRA74x silicon rev 1.1, pcie_pcs register definition has changed.
Bits 16-23 are used to configure delay values for *both* phy1 and phy2.

Hence phyid is no longer required.

So, drop id field from ti_pipe3 structure and its subsequent references
for configuring pcie_pcs register.

Also, pcie_pcs register now needs to be configured with delay value of 0x96
at bit positions 16-23. See register description of CTRL_CORE_PCIE_PCS in
ARM572x TRM, SPRUHZ6, October 2014, section 18.5.2.2, table 18-1804.

This is needed to ensure Gen2 cards are enumerated consistently.

DRA72x silicon behaves same way as DRA74x rev 1.1 as far as this functionality
is considered.

Test results on DRA74x and DRA72x EVMs:

Before patch
------------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register

DRA72x: Gen1 cards work, Gen2 cards do not work sometimes due to incorrect
programming of register

After patch
-----------
DRA74x ES 1.0: Gen1 cards work, Gen2 cards do not work (expected result due to
silicon errata)
DRA74x ES 1.1: Gen1 cards work, Gen2 cards work consistently.

DRA72x: Gen1 and Gen2 cards enumerate consistently.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-12-23 15:44:32 +05:30
Hans de Goede 372400344a phy-sun4i-usb: Change disconnect threshold value for sun6i
The allwinner SDK uses a value of 3 for the disconnect threshold setting on
sun6i, do the same in the kernel.

In my previous experience with sun5i problems getting the threshold right
is important to avoid usb2 devices being unplugged sometimes going unnoticed.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-12-23 15:44:31 +05:30
Dan Carpenter 4e038e8919 phy: miphy28lp: unlock on error in miphy28lp_init()
We need to unlock before returning the -EINVAL here.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-12-23 15:44:31 +05:30
Linus Torvalds c0f486fde3 More ACPI and power management updates for 3.19-rc1
- Fix a regression in leds-gpio introduced by a recent commit that
    inadvertently changed the name of one of the properties used by
    the driver (Fabio Estevam).
 
  - Fix a regression in the ACPI backlight driver introduced by a
    recent fix that missed one special case that had to be taken
    into account (Aaron Lu).
 
  - Drop the level of some new kernel messages from the ACPI core
    introduced by a recent commit to KERN_DEBUG which they should
    have used from the start and drop some other unuseful KERN_ERR
    messages printed by ACPI (Rafael J Wysocki).
 
  - Revert an incorrect commit modifying the cpupower tool
    (Prarit Bhargava).
 
  - Fix two regressions introduced by recent commits in the OPP
    library and clean up some existing minor issues in that code
    (Viresh Kumar).
 
  - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
    the tree (or drop it where that can be done) in order to make
    it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
    Ulf Hansson, Ludovic Desroches).  There will be one more
    "CONFIG_PM_RUNTIME removal" batch after this one, because some
    new uses of it have been introduced during the current merge
    window, but that should be sufficient to finally get rid of it.
 
  - Make the ACPI EC driver more robust against race conditions
    related to GPE handler installation failures (Lv Zheng).
 
  - Prevent the ACPI device PM core code from attempting to
    disable GPEs that it has not enabled which confuses ACPICA
    and makes it report errors unnecessarily (Rafael J Wysocki).
 
  - Add a "force" command line switch to the intel_pstate driver
    to make it possible to override the blacklisting of some
    systems in that driver if needed (Ethan Zhao).
 
  - Improve intel_pstate code documentation and add a MAINTAINERS
    entry for it (Kristen Carlson Accardi).
 
  - Make the ACPI fan driver create cooling device interfaces
    witn names that reflect the IDs of the ACPI device objects
    they are associated with, except for "generic" ACPI fans
    (PNP ID "PNP0C0B").  That's necessary for user space thermal
    management tools to be able to connect the fans with the
    parts of the system they are supposed to be cooling properly.
    From Srinivas Pandruvada.
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJUk0IDAAoJEILEb/54YlRx7fgP/3+yF/0TnEW93j2ALDAQFiLF
 tSv2A2vQC8vtMJjjWx0z/HqPh86gfaReEFZmUJD/Q/e2LXEnxNZJ+QMjcekPVkDM
 mTvcIMc2MR8vOA/oMkgxeaKregrrx7RkCfojd+NWZhVukkjl+mvBHgAnYjXRL+NZ
 unDWGlbHG97vq/3kGjPYhDS00nxHblw8NHFBu5HL5RxwABdWoeZJITwqxXWyuPLw
 nlqNWlOxmwvtSbw2VMKz0uof1nFHyQLykYsMG0ZsyayCRdWUZYkEqmE7GGpCLkLu
 D6yfmlpen6ccIOsEAae0eXBt50IFY9Tihk5lovx1mZmci2SNRg29BqMI105wIn0u
 8b8Ej7MNHp7yMxRpB5WfU90p/y7ioJns9guFZxY0CKaRnrI2+BLt3RscMi3MPI06
 Cu2/WkSSa09fhDPA+pk+VDYsmWgyVawigesNmMP5/cvYO/yYywVRjOuO1k77qQGp
 4dSpFYEHfpxinejZnVZOk2V9MkvSLoSMux6wPV0xM0IE1iD0ulVpHjTJrwp80ph4
 +bfUFVr/vrD1y7EKbf1PD363ZKvJhWhvQWDgETsM1vgLf21PfWO7C2kflIAsWsdQ
 1ukD5nCBRlP4K73hG7bdM6kRztXhUdR0SHg85/t0KB/ExiVqtcXIzB60D0G1lENd
 QlKbq3O4lim1WGuhazQY
 =5fo2
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more ACPI and power management updates from Rafael Wysocki:
 "These are regression fixes (leds-gpio, ACPI backlight driver,
  operating performance points library, ACPI device enumeration
  messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
  PM), some cleanups in the operating performance points (OPP)
  framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
  minor intel_pstate driver changes, a new MAINTAINERS entry for it and
  an ACPI fan driver change needed for better support of thermal
  management in user space.

  Specifics:

   - Fix a regression in leds-gpio introduced by a recent commit that
     inadvertently changed the name of one of the properties used by the
     driver (Fabio Estevam).

   - Fix a regression in the ACPI backlight driver introduced by a
     recent fix that missed one special case that had to be taken into
     account (Aaron Lu).

   - Drop the level of some new kernel messages from the ACPI core
     introduced by a recent commit to KERN_DEBUG which they should have
     used from the start and drop some other unuseful KERN_ERR messages
     printed by ACPI (Rafael J Wysocki).

   - Revert an incorrect commit modifying the cpupower tool (Prarit
     Bhargava).

   - Fix two regressions introduced by recent commits in the OPP library
     and clean up some existing minor issues in that code (Viresh
     Kumar).

   - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
     tree (or drop it where that can be done) in order to make it
     possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
     Hansson, Ludovic Desroches).

     There will be one more "CONFIG_PM_RUNTIME removal" batch after this
     one, because some new uses of it have been introduced during the
     current merge window, but that should be sufficient to finally get
     rid of it.

   - Make the ACPI EC driver more robust against race conditions related
     to GPE handler installation failures (Lv Zheng).

   - Prevent the ACPI device PM core code from attempting to disable
     GPEs that it has not enabled which confuses ACPICA and makes it
     report errors unnecessarily (Rafael J Wysocki).

   - Add a "force" command line switch to the intel_pstate driver to
     make it possible to override the blacklisting of some systems in
     that driver if needed (Ethan Zhao).

   - Improve intel_pstate code documentation and add a MAINTAINERS entry
     for it (Kristen Carlson Accardi).

   - Make the ACPI fan driver create cooling device interfaces witn
     names that reflect the IDs of the ACPI device objects they are
     associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").

     That's necessary for user space thermal management tools to be able
     to connect the fans with the parts of the system they are supposed
     to be cooling properly.  From Srinivas Pandruvada"

* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
  MAINTAINERS: add entry for intel_pstate
  ACPI / video: update the skip case for acpi_video_device_in_dod()
  power / PM: Eliminate CONFIG_PM_RUNTIME
  NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  ACPI / EC: Fix unexpected ec_remove_handlers() invocations
  Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
  tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
  PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
  mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
  PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
  ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  ACPI / PM: Do not disable wakeup GPEs that have not been enabled
  ACPI / utils: Drop error messages from acpi_evaluate_reference()
  ...
2014-12-18 20:28:33 -08:00
Rafael J. Wysocki 7ba37053eb phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/phy/.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-12-13 00:42:12 +01:00
Greg Kroah-Hartman 842f57baab Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
 miscellaneous fixes and cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJUdsDPAAoJEA5ceFyATYLZvxMP/2xNqB8P51jzoPDH3ZhubINg
 0A0nuzjPhYRDMYsPMEydno7h2X5qeJtY6NanjE5Z9N3jLzSvhN60SkYXqTBX5MYB
 WweSug/grQOTBlo3vtFgih2bPax8qAV24BPDCGgQ71zTctU2Ni/DsJoejQbxDDuJ
 BaC3cRhje8tljygS+wqqEWNyh1SezhqPKmI3tkEpCaZ3gcK1wvvTnLc5kkZW/855
 27HiqAcWZKbczv5qGUqVoYWd/psgjF2o/8nqPz0A+uMrh3RaaMMgTjh6LQW9nVrd
 IiWCbyLwwDsdVQL7PIziD+NBn8ISPMKyf9j1Exxt41wkluBYfJVlE6KGALKRatv6
 /ZxiwW3iU1pMFZaTnfasH0ChJTP13IQafX/Dne8BNoUhVr/PjGwXN3mJfBTpyTjN
 E10+cPpVKWCKyDtvqRUPeQp//+th2oXxNSJ++ealrr/xARamjWpUVxjTZwhmAS2C
 7tTOierElhVyk3XNhrdGPhn7B9I5zquIVv0AALU3D7GWWLsIBbEKihYCDSClkKgl
 iLykw7W7Uj0PDzkeSGYmwd3vVLrDvcnDyzJby4hojyrCZ0N/873iz2APJGrWdSMg
 j+JBRAXI9LMXDMfhD3oRaq1uDxGhg7BIm903V3r38L2MmG7902pKK2iBaYwpRc7o
 dE8iljdnygp7Rat/4vTo
 =oo3u
 -----END PGP SIGNATURE-----

Merge tag 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing

Kishon writes:

Improvements in phy-core specifically on PHY core finds the PHY in the case
of non-dt boot. Adds three new PHY drivers using the PHY framework and some
miscellaneous fixes and cleanups.
2014-11-27 08:25:20 -08:00
Gregory CLEMENT eee47538ec phy: add support for USB cluster on the Armada 375 SoC
The Armada 375 SoC comes with an USB2 host and device controller and
an USB3 controller. The USB cluster control register allows to manage
common features of both USB controllers.

This commit adds a driver integrated in the generic PHY framework to
control this USB cluster feature.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
[ kishon@ti.com : Made it to use the updated devm_phy_create API and
		  soem cosmentic changes in Kconfig file.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
2014-11-26 11:07:14 +05:30
Gregory CLEMENT c1fc005010 phy: Use PTR_ERR_OR_ZERO to fix warning raised by coccinelle
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: coccinelle/api/ptr_ret.cocci

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-26 11:07:13 +05:30
Greg Kroah-Hartman 2d4d9f35ba usb: patches for v3.19 merge window
This time, a very pull request with 216 non-merge
 commits. Most of the commits contained here are
 sparse or coccinelle fixes ranging from missing
 'static' to returning 0 in case of errors.
 
 More importantly, we have the removal the now
 unnecessary 'driver' argument to ->udc_stop().
 
 DWC2 learned about Dual-Role builds. Users of
 this IP can now have a single driver built for
 host and device roles.
 
 DWC3 got support for two new HW platforms: Exynos7
 and AMD.
 
 The Broadcom USB 3.0 Device Controller IP is now
 supported and so is PLX USB338x, which means DWC3
 has lost is badge as the only USB 3.0 peripheral
 IP supported on Linux.
 
 Thanks for Tony Lindgren's work, we can now have
 a distro-like kernel where all MUSB glue layers
 can be built into the same kernel (statically
 or dynamically linked) and it'll work in PIO (DMA
 will come probably on v3.20).
 
 Other than these, the usual set of cleanups and
 non-critical fixes.
 
 Signed-off-by: Felipe Balbi <balbi@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJUdJoNAAoJEIaOsuA1yqREqDoP/iwVojhk1qb2PQAJvLkl8To4
 R34RM8zt8IRhE+yWIW8hm8xvsLiwvujBMgsphUmyu2k0X/NtPl1ElrDvObWwO0N8
 ouyLISRw/wLUs8hJwsNVhIX0VjPxDQ6648C3OZYjySTtNtsh0rBw84ALX+IWkDye
 Thb823xEunGYVwjhq8WrfT94q6LjyPp00XHlA4mf3XgSpXC2tKBFGmIcfmwObzYI
 LkON7kJTp14XEeIYGYJO+7MBpo8s7YFmnpsDOV2QYlz/i0pRdjLwaKMN5T7D7DO5
 YdvcQFQUM53dvq+tiw2k2iW4gmn9ktHHlckn8W5hhQZCs4ujSzYy/vP4GcbNEaTf
 CuDocJGTr7ieU2IqYiTM+wRYavBoHLq9V5AHZmgsZ/pVF8lvG0hcX0fmd7XXScjv
 GaKJqyQMaKZ9tRF9RZdMZeOrICp1X1X+KcqdG7yXoOtsVdn0O3zHdxYcZcVa29X/
 cXuttoTywQgfrlI/uWWwpkYlqiHeawK1EooZ/6fYQDviLm4lrLPp94vF/5MqGM1j
 f2tNpG63iOzLUUYJa+YgPqs6RrZLM3soZcf3bFAEt9sA99gc3ExwCYXurBEnTONr
 XUowTfNKxPaVjNPZ1evGwF5F+WLEK4s88weB9lArd2S3NFP3DQV1cRpWj8rLYE72
 lX6aWEWUDqnUHmwJUgIb
 =WYyZ
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v3.19 merge window

This time, a very pull request with 216 non-merge
commits. Most of the commits contained here are
sparse or coccinelle fixes ranging from missing
'static' to returning 0 in case of errors.

More importantly, we have the removal the now
unnecessary 'driver' argument to ->udc_stop().

DWC2 learned about Dual-Role builds. Users of
this IP can now have a single driver built for
host and device roles.

DWC3 got support for two new HW platforms: Exynos7
and AMD.

The Broadcom USB 3.0 Device Controller IP is now
supported and so is PLX USB338x, which means DWC3
has lost is badge as the only USB 3.0 peripheral
IP supported on Linux.

Thanks for Tony Lindgren's work, we can now have
a distro-like kernel where all MUSB glue layers
can be built into the same kernel (statically
or dynamically linked) and it'll work in PIO (DMA
will come probably on v3.20).

Other than these, the usual set of cleanups and
non-critical fixes.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-25 09:31:14 -08:00
Vivek Gautam 556186a02c phy: exynos7-usbdrd: Update dependency for ARCH_EXYNOS
This PHY controller is also present on Exynos7 platform
in arch-exynos family.
So PHY_EXYNOS5_USBDRD should now depend on ARCH_EXYNOS.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-22 14:08:09 +05:30
Vivek Gautam a6867836db phy: exynos5-usbdrd: Add facility for VBUS-BOOST-5V supply
Some Exynos boards have a separate regulator controlling a
Boost 5V supply which goes as input for VBUS regulator.
So adding a control for the same in driver, to enable
vbus supply on the port.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-22 14:08:09 +05:30
Vivek Gautam 9bde18c1b5 phy: exynos5-usbdrd: Add pipe-clk, utmi-clk and itp-clk support
Exynos7 SoC has now separate gate control for 125MHz pipe3 phy
clock, as well as 60MHz utmi phy clock.
Additionally, separate gate control is available for the clock
used for ITP (Isochronous Transfer Packet) generation.

So get the same and control in the phy-exynos5-usbdrd driver.

Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-22 14:08:09 +05:30
Heikki Krogerus dbc98635e0 phy: remove the old lookup method
The users of the old method are now converted to the new one.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ kishon@ti.com : made phy-berlin-usb.c and phy-miphy28lp.c to use the updated
		  devm_phy_create API.]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-22 13:58:39 +05:30
Heikki Krogerus 61211b1bda phy: twl4030: use the new lookup method
Creates the lookup separately. Hard coding the consumer as
it can't be anything else except musb.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-22 13:58:31 +05:30
Heikki Krogerus b7bc15b98e phy: improved lookup method
Separates registration of the phy and the lookup. The method
is copied from clkdev.c,

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-21 19:48:50 +05:30
Antoine Tenart 13ebb68cb5 phy: add the Berlin USB PHY driver
Add the driver driving the Marvell Berlin USB PHY. This allows to
initialize the PHY and to use it from the USB driver later.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-21 19:48:50 +05:30
Sebastian Hesselbarth 8203f8b461 phy: berlin-sata: Add support for BG2 SATA PHY
Berlin BG2 also has a SATA PHY compatible with the current driver
except different PHY_BASE. Add a new compatible to the driver
reflecting the different PHY_BASE.

Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-13 11:49:43 +05:30
Sebastian Hesselbarth a98d41d6a1 phy: berlin-sata: Move PHY_BASE into private data struct
Currently, Berlin SATA PHY driver assumes PHY_BASE address being
constant. While this PHY_BASE is correct for BG2Q, older BG2 PHY_BASE
is different. Prepare the driver for BG2 support by moving the phy_base
into private driver data.

Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-13 11:49:43 +05:30
Roman Byshko 6827a46f59 phy: sun4i: add support for USB phy0
The driver for sun4i USB phys currently supports
only phy1 and phy2 which are used for USB host
controllers. This patch adds support for USB phy0,
which is used by the musb hdrc USB controller.

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-13 11:49:23 +05:30
Kishon Vijay Abraham I 491e049064 phy: phy-core: use the np present in of_phandle_args to get the PHY
Instead of using the node pointer of the PHY provider and then scanning its
child nodes to get a reference to the PHY, directly use the node pointer
present in of_phandle_args to get a reference to the PHY.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-12 18:40:13 +05:30
Gabriel FERNANDEZ 28ba384dc5 phy: miphy28lp: Tune tx impedance across Soc cuts
This patch to compensate tx impedance (Sata, PCIe)
depending on Soc cuts the kernel is built for.

Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-12 18:40:13 +05:30
Gabriel FERNANDEZ a2108dee3c phy: miphy28lp: Add SSC support for PCIE
SSC is the technique of modulating the operating frequency of a signal
slightly to spread its radiated emissions over a range of frequencies.
This reduction in the maximum emission for a given frequency helps meet
radiated emission requirements.
These settings are applicable for PCIE with Internal clock.

Signed-off-by: Harsh Gupta <harsh.gupta@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-12 18:40:12 +05:30
Gabriel FERNANDEZ 2b041b27a8 phy: miphy28lp: Add SSC support for SATA
This patch to tune on/off the ssc on miphy sata setup.
User can now enable ssc via dt blob, it is useful to reduce
effects of EMI.

Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-12 18:40:12 +05:30
Gabriel FERNANDEZ 2c14e9be0c phy: miphy28lp: Provide support for the MiPHY28lp Generic PHY
The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.

Signed-off-by: alexandre torgue <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-11-12 18:40:12 +05:30
Felipe Balbi 8b9ca2767b phy: twl4030: Fix build breakage
commit e47d925 (usb: move the OTG state
from the USB PHY to the OTG structure) moved
the OTG state field from struct usb_phy to
struct usb_otg but, even though I fixed many
other build breakages, I still missed one
on phy-twl4030-usb.c.

Fix the build breakage now.

While at that, also a build warning introduced
by the same commit.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-10 17:19:34 -06:00
Oussama Ghorbel f20531a9aa phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly
The USB OTG port does not work since v3.16 on omap platform.
This is a regression introduced by the commit
eb82a3d846 (phy: omap-usb2: Balance pm_runtime_enable() on probe failure
 and remove).
This because the call to pm_runtime_enable() function is moved after the
call to devm_phy_create() function, which has side effect since later in
the subsequent calls of devm_phy_create() there is a check with
pm_runtime_enabled() to configure few things.

Fixes: eb82a3d846
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-11-05 14:34:06 -08:00
Antoine Tenart 19c1eac268 usb: rename phy to usb_phy in OTG
This patch prepares the introduction of the generic PHY support in the
USB OTG common functions. The USB PHY member of the OTG structure is
renamed to 'usb_phy' and modifications are done in all drivers accessing
it. Renaming this pointer will allow to keep the compatibility for USB
PHY drivers.

Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:01:25 -06:00
Antoine Tenart e47d92545c usb: move the OTG state from the USB PHY to the OTG structure
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.

[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
		phy-isp1301-omap, and chipidea's debug.c ]

Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-11-03 10:01:25 -06:00
Peter Griffin 4f0eb5d7ef phy: remove .owner field for drivers using module_platform_driver
This patch removes the superflous .owner field for drivers which
use the module_platform_driver or platform_driver_register api,
as this is overriden in __platform_driver_register.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:34 +05:30
Vivek Gautam a5ec598650 phy: exynos-dp-video: Use syscon support to control pmu register
Currently the DP_PHY_ENABLE register is mapped in the driver,
and accessed to control power to the PHY.
With mfd-syscon and regmap interface available at our disposal,
it's wise to use that instead of using a 'reg' property for the
controller and allocating a memory resource for that.

To facilitate this, we have added another compatible string
for Exynso5420 SoC to acquire driver data which contains
different DP-PHY-CONTROL register offset.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:34 +05:30
Peter Griffin 3f8da2e36c phy: phy-stih41x-usb: Add usb phy support for STiH41x SoCs.
This driver adds support for USB (1.1 and 2.0) phy for STiH415 and
STiH416 System-On-Chips from STMicroelectronics.

Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:33 +05:30
Peter Griffin 89ae1f5d4c phy: phy-stih407-usb: Add usb picoPHY driver found on stih407 SoC family
This is the generic phy driver for the picoPHY ports used by the
USB2 and USB3 Host controllers when controlling usb2/1.1 devices. It
is found on STiH407 SoC family from STMicroelectronics.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:33 +05:30
Tony Lindgren dcc35b2160 usb: phy: twl4030-usb: Use mutex instead of spinlock for protecting the data
We're using threaded irq on a I2C bus and we're sleeping in
twl4030_usb_irq() as it calls twl4030_usb_linkstat() which
calls the i2c functions. If we ever need to lock for longer
I2C transaction sequences a mutex will allow us to do that
easily.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:33 +05:30
Tony Lindgren 48f48e172c usb: phy: twl4030-usb: Remove asleep and rely on runtime PM
There's no longer need for tracking the phy state in the driver
with asleep, we can now rely on runtime PM.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:33 +05:30
Tony Lindgren bad8e33582 usb: phy: twl4030-usb: Move code from twl4030_phy_power to the runtime PM calls
We don't need twl4030_phy_power() any longer now that we have
the runtime PM calls. Let's get rid of it as it's confusing.
No functional changes, just move the code and use res instead
of ret as we are not returning that value.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Tony Lindgren 62dc5769bb usb: phy: twl4030-usb: Simplify phy init to use runtime PM
We can now let the interrupt and delayed work do all that's
needed with runtime PM.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Tony Lindgren bb419402cc usb: phy: twl4030-usb: Remove unused irq_enabled
It's not being used any longer.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 25451e5cb9 phy: phy-spear1340-miphy: Use module_platform_driver to register driver.
Using the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.

Also remove .owner field as this gets overridden in __platform_driver_register.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 7e65e9c94a phy: phy-spear1310-miphy: Use module_platform_driver to register driver.
Use the module_platform_driver macro to register the driver as this gets
rid of a lot of the boilerplate code.

Also remove .owner field as this gets overridden in __platform_driver_register.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 556bdebb3b phy: phy-spear1340-miphy: Remove unncessary site specific OOM messages
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().

Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 0e71e23563 phy: phy-spear1310-miphy: Remove unncessary site specific OOM messages
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().

Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 3a4cfcbbaf phy: phy-ti-pipe3: Remove unncessary site specific OOM messages
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().

Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 0b68253d9f phy: phy-omap-usb2: Remove unncessary site specific OOM messages
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().

Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:32 +05:30
Peter Griffin 1f8de849cf phy: phy-mvebu-sata: Add missing error check for devm_kzalloc
Currently this driver is missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.

This patch adds the aformentioned missing check.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:31 +05:30
Peter Griffin 437a6bc478 phy: phy-omap-control: Remove unncessary site specific OOM messages
The site specific OOM messages are unncessary, because they duplicate
messages from the memory subsystem which include dump_stack().

Removing these superflous messages makes the kernel smaller. A discussion
here http://patchwork.ozlabs.org/patch/324158/ found that all error paths
from kzalloc will print a error message, and that any error path which maybe
found which doesn't would be considered a bug in kzalloc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:31 +05:30
Sergei Shtylyov 1233f59f74 phy: Renesas R-Car Gen2 PHY driver
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.

This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing  of USB channels to the controller be dynamic, depending on what
USB drivers  are loaded,  rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c  seems to fit that purpose
ideally. The new driver only  supports device tree probing  for now.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-24 15:18:31 +05:30
Bartlomiej Zolnierkiewicz 7652d35f98 phy: spear1340-miphy: fix driver dependencies
ST SPEAR1340-MIPHY support should be available only on
ST SPEAr1340 machine.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-12 11:35:31 +05:30
Bartlomiej Zolnierkiewicz 6100a7c1e9 phy: spear1310-miphy: fix driver dependencies
ST SPEAR1310-MIPHY support should be available only on
ST SPEAr1310 machine.

Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-12 11:35:31 +05:30
Lee Jones a6cc1b9478 phy: miphy365x: Fix off-by-one error
We index the RX/TX speed select values in the following way:

  rx_tx_spd[miphy_phy->sata_gen];

However rx_tx_spd[] starts at index zero and the SATA_GENx's start
at one.  In this patch we pad out the first element in rx_tx_spd[]
in an attempt to realign the values.

Cc: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-09-12 11:35:31 +05:30
Lee Jones fbb1a77003 phy: miphy365x: Select GENERIC_PHY instead of depending on it
Enabling GENERIC_PHY in the shared (by most ARM sub-architectures)
defconfig multi_v7_defconfig is prohibited.  Instead, we'll enable
it from the Kconfig whenever PHY_MIPHY365X is enabled.

Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-08-28 11:17:43 +05:30
Sjoerd Simons 4cdcd14dc9 phy: exynos5-usbdrd: Add MODULE_DEVICE_TABLE entry
Add a MODULE_DEVICE_TABLE call for OF match tables. This allows the
module to be autoloaded based on devicetree information.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-08-28 11:17:43 +05:30
Tony Lindgren 85601b8d81 usb: phy: twl4030-usb: Fix lost interrupts after ID pin goes down
Commit 249751f223 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c9e ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.

The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.

The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().

But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.

Fixes: f1ddc24c9e ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops")
Cc: stable@vger.kernel.org # v3.13+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-08-24 17:47:54 +05:30
Tony Lindgren 96be39ab34 usb: phy: twl4030-usb: Fix regressions to runtime PM on omaps
Commit 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12be2 ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.

These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.

As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.

Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.

Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().

Fixes: 30a70b026b ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
Fixes: 3063a12be2 ("usb: musb: fix PHY power on/off")
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-08-24 17:47:53 +05:30
Linus Torvalds 10c8e05620 ARM: SoC driver changes for 3.17
A handful of driver-related changes. We've had a bunch of them going in through
 other branches as well, so it's only a part of what we really have this release.
 
 Larger pieces are:
 
 * Removal of a now unused PWM driver for atmel
   - This includes AVR32 changes that have been appropriately acked.
 * Performance counter support for the arm CCN interconnect
 * OMAP mailbox driver cleanups and consolidation
 * PCI and SATA PHY drivers for SPEAr 13xx platforms
 * Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
   better model regulators/power.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJT5DrJAAoJEIwa5zzehBx3wkkP/iwEfEK5mMon9KEe4DcKTKNq
 Z6xyWuMQNHKdfBFpABs6AsHQCKDc7KK6gN3+2zLLHEJ4XGDPZ2g2NaX3oRPJlaay
 BDK7rQfIZyi4tmbOnlEv1BDTYgirYBPMwk9RyNo/04Ug3W+Y67aSVo44zkNFBWaJ
 GbcX/zYsrsfvdawuQMW6V/A835s3Kq5Zhv1ikPr8gDDjswZRBAT6i7FYpBSHQ8K8
 bH6C1891Xit6rxXSLXJyrtM8CAet7PtLTqNr/IKdUaJnGD+fJm5EonxW+g8gvhN8
 gOEkm3nM60++kdDlzZCQVNr0m1+ih6NNCr6bDLO6rIRpAJM2O+YrN1rWuZaJOu1A
 pIvifk+wWHT+o52pXk8g9fK4n/ZJydK3IBzDePHMrIROOEiW5tLE3WA+u3NSfMfH
 WegMt9E2dcB+5gXPeejZ9gFbAHnh2S1oVTZfCYXtuOHrYiEU9U0FA3eRYvJEE2po
 k8sdiOn7Vc65O1QZ+xZNbLABpAHaye7X2evOJyhSutzHE/AtUvT4vuCAZ0tggXyD
 E1qVKngVW/NvcoFbwYeidq4bOVgiAEn3idZgF5gEq1mq7LzetXUQAcZAOQfLWHLQ
 RrXufS7Ez8pSCG74y0AFReVfQH2PgWHPqGUGj99NXgQauexc/vR1Hc5Iqb8liGNJ
 n6i8RqvvQ4KYcmHEXDIT
 =fsP6
 -----END PGP SIGNATURE-----

Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver changes from Olof Johansson:
 "A handful of driver-related changes.  We've had a bunch of them going
  in through other branches as well, so it's only a part of what we
  really have this release.

  Larger pieces are:

   - Removal of a now unused PWM driver for atmel
     [ This includes AVR32 changes that have been appropriately acked ]
   - Performance counter support for the arm CCN interconnect
   - OMAP mailbox driver cleanups and consolidation
   - PCI and SATA PHY drivers for SPEAr 13xx platforms
   - Redefinition (with backwards compatibility!) of PCI DT bindings for
     Tegra to better model regulators/power"

Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.

Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.

* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
  bus: arm-ccn: Fix error handling at event allocation
  mailbox/omap: add a parent structure for every IP instance
  mailbox/omap: remove the private mailbox structure
  mailbox/omap: consolidate OMAP mailbox driver
  mailbox/omap: simplify the fifo assignment by using macros
  mailbox/omap: remove omap_mbox_type_t from mailbox ops
  mailbox/omap: remove OMAP1 mailbox driver
  mailbox/omap: use devm_* interfaces
  bus: ARM CCN: add PERF_EVENTS dependency
  bus: ARM CCN PMU driver
  PCI: spear: Remove spear13xx_pcie_remove()
  PCI: spear: Fix Section mismatch compilation warning for probe()
  ARM: tegra: Remove legacy PCIe power supply properties
  PCI: tegra: Remove deprecated power supply properties
  PCI: tegra: Implement accurate power supply scheme
  ARM: SPEAr13xx: Update defconfigs
  ARM: SPEAr13xx: Add pcie and miphy DT nodes
  ARM: SPEAr13xx: Add bindings and dt node for misc block
  ARM: SPEAr13xx: Fix static mapping table
  phy: Add drivers for PCIe and SATA phy on SPEAr13xx
  ...
2014-08-08 11:34:32 -07:00
Linus Torvalds b3345d7c57 ARM: SoC platform changes for 3.17
This is the bulk of new SoC enablement and other platform changes for 3.17:
 
 * Samsung S5PV210 has been converted to DT and multiplatform
 * Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
 * Kirkwood, one of the popular Marvell platforms, is folded into the
   mvebu platform code, removing mach-kirkwood.
 * Hwmod data for TI AM43xx and DRA7 platforms.
 * More additions of Renesas shmobile platform support
 * Removal of plat-samsung contents that can be removed with S5PV210 being
   multiplatform/DT-enabled and the other two old platforms being removed.
 
 New platforms (most with only basic support right now):
 
 * Hisilicon X5HD2 settop box chipset is introduced
 * Mediatek MT6589 (mobile chipset) is introduced
 * Broadcom BCM7xxx settop box chipset is introduced
 
 + as usual a lot other pieces all over the platform code.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.14 (GNU/Linux)
 
 iQIcBAABAgAGBQJT5Dp+AAoJEIwa5zzehBx3w1sP/0vjT/LQOmC8Lv8RW2Ley2ua
 hNu3HcNPnT/N40JEdU9YNv3q0fdxGgcfKj011CNN+49zPSUf1xduk2wfCAk9yV50
 8Sbt1PfDGm1YyUugGN420CzI431pPoM1OGXHZHkAmg+2J286RtUi3NckB//QDbCY
 QhEjhpYc9SXhAOCGwmB4ab7thOljOFSPzKTLMTu3+PNI5zRPRgkDkt6w9XlsAYmB
 nuR271BnzsROkMzAjycwaJ3kdim7wqrMRfk8g96o0jHSF5qf4zsT5uWYYAjTxdUQ
 8Ajz6zjeHe4+95TwTDcq+lCX6rDLZgwkvCAc6hFbeg0uR7Dyek0h6XMEYtwdjaiU
 KNPwOENrYdENNDAGRpkFp1x4h/rY9Plfru0bBo5o6t7aPBvmNeCDzRtlTtLiUNDV
 dG8sfDMtrS/wFHVjylDSQ60Mb+wuW0XneC8D7chY/iRhIllUYi6YXXvt+/tH5C20
 oYDOWqqcDFSb0sJhE5pn4KBV82ZaHx9jMBWGLl+erg2sDX/SK8SxOkLqKYZKtKB5
 0leOGE3Y+C70xt3G9HftLz2sAvvt+C8UPsApPT+dHNE401TWJOYx6LphPkQKjeeK
 P1iwKi+It3l+FaBypgJy/LeMQRy7EyvDBK2I5WoVL/R2qq14EmP1ui3Tthjj0bhq
 tBBof6P9c8OnRVj1Lz3R
 =5TJ6
 -----END PGP SIGNATURE-----

Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Olof Johansson:
 "This is the bulk of new SoC enablement and other platform changes for
  3.17:

   - Samsung S5PV210 has been converted to DT and multiplatform
   - Clock drivers and bindings for some of the lower-end i.MX 1/2
     platforms
   - Kirkwood, one of the popular Marvell platforms, is folded into the
     mvebu platform code, removing mach-kirkwood
   - Hwmod data for TI AM43xx and DRA7 platforms
   - More additions of Renesas shmobile platform support
   - Removal of plat-samsung contents that can be removed with S5PV210
     being multiplatform/DT-enabled and the other two old platforms
     being removed

  New platforms (most with only basic support right now):

   - Hisilicon X5HD2 settop box chipset is introduced
   - Mediatek MT6589 (mobile chipset) is introduced
   - Broadcom BCM7xxx settop box chipset is introduced

  + as usual a lot other pieces all over the platform code"

* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
  ARM: hisi: remove smp from machine descriptor
  power: reset: move hisilicon reboot code
  ARM: dts: Add hix5hd2-dkb dts file.
  ARM: debug: Rename Hi3716 to HIX5HD2
  ARM: hisi: enable hix5hd2 SoC
  ARM: hisi: add ARCH_HISI
  MAINTAINERS: add entry for Broadcom ARM STB architecture
  ARM: brcmstb: select GISB arbiter and interrupt drivers
  ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
  ARM: configs: enable SMP in bcm_defconfig
  ARM: add SMP support for Broadcom mobile SoCs
  Documentation: arm: misc updates to Marvell EBU SoC status
  Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
  ARM: mvebu: fix build without platforms selected
  ARM: mvebu: add cpuidle support for Armada 38x
  ARM: mvebu: add cpuidle support for Armada 370
  cpuidle: mvebu: add Armada 38x support
  cpuidle: mvebu: add Armada 370 support
  cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
  ARM: mvebu: export the SCU address
  ...
2014-08-08 11:14:29 -07:00
Lee Jones 7ebdb52e19 phy: miphy365x: Represent each PHY channel as a DT subnode
This has the added advantages of being able to enable/disable each
of the channels as simply as enabling/disabling the DT node.

Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:43 +05:30
Lee Jones 6e877fedb1 phy: miphy365x: Provide support for the MiPHY356x Generic PHY
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.

Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:37 +05:30
Kumar Gala 4f6160d408 phy: qcom: Add driver for QCOM IPQ806x SATA PHY
Add a PHY driver for uses with AHCI based SATA controller driver on the
IPQ806x family of SoCs.

Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:12 +05:30
Srinivas Kandagatla 175f02ebdf phy: qcom-apq8064: fix possible timeout without check
This patch fixes a possible timeout in poll loop without actually
checking the register before return. In theory the there is a possibility
of loop being scheduled after a long lock/delay, which would then force
the loop to exit without actually checking the register.

Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:12 +05:30
Kishon Vijay Abraham I f0ed817638 phy: core: Let node ptr of PHY point to PHY and not of PHY provider
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
2014-07-22 12:46:11 +05:30
Kishon Vijay Abraham I 2a4c37016c phy: core: Fix of_phy_provider_lookup to return PHY provider for sub node
Fixed of_phy_provider_lookup to return 'phy_provider' if _of_phy_get
passes the node pointer of the sub-node of phy provider node. This is
needed when phy provider implements multiple PHYs and each PHY is
modelled as the sub-node of PHY provider device node.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
2014-07-22 12:46:11 +05:30
Antoine Ténart 942a31b521 phy: add a driver for the Berlin SATA PHY
The Berlin SoC has a two SATA ports. Add a PHY driver to handle them.

The mode selection can let us think this PHY can be configured to fit
other purposes. But there are reasons to think the SATA mode will be
the only one usable: the PHY registers are only accessible indirectly
through two registers in the SATA range, the PHY seems to be integrated
and no information tells us the contrary. For these reasons, make the
driver a SATA PHY driver.

Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:11 +05:30
Andrew Lunn 74d64b59b4 phy: Remove ARCH_KIRKWOOD dependency
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when these SoCs are built
as part of mach-mvebv.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:11 +05:30
Srinivas Kandagatla 1de990d8a1 phy: qcom: Add driver for QCOM APQ8064 SATA PHY
Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.

This patch is a forward port from Qualcomm's v3.4 andriod kernel.

Tested on IFC6410 board.

CC: Sujit Reddy Thumma <sthumma@codeaurora.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:11 +05:30
Sachin Kamat c233f52948 phy: Kconfig: Update config for Exynos USB DRD
USB DWC3 driver on Exynos platform does not work without its
corresponding phy driver. Hence make the PHY driver depend on
Exynos DWC3 driver and default it to yes to make things easier
for the end user.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:11 +05:30
Sachin Kamat d6125af9af phy: Kconfig: Re-organize Exynos USB 2.0 PHY configs
Since the USB 2.0 PHYs are required with EHCI/OHCI USB drivers and
USB gadget controller supported by the DWC2 gadget driver, make it
depend on them and default to ARCH_EXYNOS as they are meant for
Exynos platforms. Also, make the sub-drivers silent options enabling
them based on the SoC platforms that they are meant to work with. This
will make life easier for end users who do not have any way knowing the
dependencies.

Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:11 +05:30
Roger Quadros 3be88125d8 phy: core: Support regulator supply for PHY power
Some PHYs can be powered by an external power regulator.
e.g. USB_HS PHY on DRA7 SoC. Make the PHY core support a
power regulator.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:10 +05:30
Marek Szyprowski 016e0d3cb7 drivers: phy: exynos-usb2: add support for Exynos 3250
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:10 +05:30
Jiancheng Xue e379413a34 phy: add hix5hd2-sata-phy driver
Add hix5hd2-sata-phy driver on Hisilicon hix5hd2 soc.

Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:10 +05:30
Kishon Vijay Abraham I f0e2cf7b91 phy: pipe3: insert delay to enumerate in GEN2 mode
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
2014-07-22 12:46:10 +05:30
Kishon Vijay Abraham I 99bbd48c20 phy: phy-omap-pipe3: Add support for PCIe PHY
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
2014-07-22 12:46:10 +05:30
Kamil Debski 57416c23e3 phy: phy-samsung-usb2: Change phy power on/power off sequence
The Exynos4412 USB 2.0 PHY hardware differs from the description provided
in the documentation. Some register bits have different function. This
patch fixes the defines of register bits and changes the way how phys are
powered on and off.

Signed-off-by: Kamil Debski <k.debski@samsung.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:10 +05:30
Jingoo Han ad6202b4d9 phy: exynos5-usbdrd: Make local functions static
Make local functions static, because these are used only in this
file.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:09 +05:30
Sachin Kamat 2d84aff9c3 phy: sun4i-usb: Use PTR_ERR_OR_ZERO
PTR_ERR_OR_ZERO simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:09 +05:30
Sachin Kamat 22fda307ca phy: exynos-mipi-video: Use PTR_ERR_OR_ZERO
PTR_ERR_OR_ZERO simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:09 +05:30
Sachin Kamat bbe21b2a9b phy: exynos-dp-video: Use PTR_ERR_OR_ZERO
PTR_ERR_OR_ZERO simplifies the code.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-07-22 12:46:09 +05:30
Mateusz Krawczuk 949ccc3a93 phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.

Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
2014-07-19 04:25:09 +09:00
Pratyush Anand 64562e9947 phy: Add drivers for PCIe and SATA phy on SPEAr13xx
ARM based ST Microelectronics's SPEAr1310/40 platforms uses ST's phy (known as
'miphy') for PCIe and SATA. This patch adds drivers for these miphys.

This also adds proper bindings for miphys.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2014-07-14 11:04:41 +05:30
Linus Torvalds 6b458ac195 USB fixes for 3.16-rc5
Here are some small USB fixes, PHY driver fixes (they ended up in this
 tree for lack of somewhere else to put them), and some new USB device
 ids.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlPBnZAACgkQMUfUDdst+ynTkACgwma2Ccj7DJl3g1zFEtM0h8ki
 8RYAnirwiO0p1B7gIKlDIgGs25JIwN61
 =tNZ2
 -----END PGP SIGNATURE-----

Merge tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
 "Here are some small USB fixes, PHY driver fixes (they ended up in this
  tree for lack of somewhere else to put them), and some new USB device
  ids"

* tag 'usb-3.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
  phy: core: Fix error path in phy_create()
  drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
  phy: omap-usb2: fix devm_ioremap_resource error detection code
  phy: sun4i: depend on RESET_CONTROLLER
  USB: serial: ftdi_sio: Add Infineon Triboard
  USB: ftdi_sio: Add extra PID.
  usb: option: Add ID for Telewell TW-LTE 4G v2
  USB: cp210x: add support for Corsair usb dongle
2014-07-12 14:13:10 -07:00
Roger Quadros eb82a3d846 phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove
If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.

This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.

Balance out the pm_runtime_enable() call in .remove() as well.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11 18:23:50 -07:00
Roger Quadros e73b49f1c4 phy: core: Fix error path in phy_create()
Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.

Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11 18:23:49 -07:00
Sjoerd Simons bf5baf954a drivers: phy: phy-samsung-usb2.c: Add missing MODULE_DEVICE_TABLE
Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11 18:23:49 -07:00
Himangi Saraogi 3df9fcd59f phy: omap-usb2: fix devm_ioremap_resource error detection code
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.

A simplified version of the semantic match that finds this problem is as
follows:

// <smpl>
@@
expression e,e1;
statement S;
@@

*e = devm_ioremap_resource(...);
if (!e1) S

// </smpl>

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11 18:23:49 -07:00
Maxime Ripard 9820ccba4b phy: sun4i: depend on RESET_CONTROLLER
The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-07-11 18:23:49 -07:00
Chen Gang 4732aee97b HID: sensor-hub: introduce Kconfig dependency on IOMEM
When NO_IOMEM is enabled (e.g. score architecture), some drivers which
need HAS_IOMEM need notice about it, or it will report related warning:

  warning: (GPIO_SCH && GPIO_ICH && GPIO_VX855 && GPIO_RDC321X && IE6XX_WDT && RADIO_WL1273 && HID_SENSOR_HUB && MFD_NVEC) selects MFD_CORE which has unmet direct dependencies (HAS_IOMEM)

Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2014-06-11 10:52:35 +02:00
Maxime Ripard eadd431239 phy: usb: sunxi: Introduce Allwinner A31 USB PHY support
The USB phy controller in the A31 differs mostly from the older controllers
because it has a clock dedicated for each phy, while the older ones were having
a single clock for all the phys.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-14 19:41:13 +05:30
Maxime Ripard 2a7f9982d6 phy: sunxi: Rework phy initialization
Move the phy initialization and variables declaration to the loop itself, since
it is where it really belongs. Also remove all the temporary variables, we can
use the structure members directly.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-14 19:41:13 +05:30
Vivek Gautam 4fc8a4e65f phy: exynos5-usbdrd: Add facility for VBUS supply
Adding support to enable/disable VBUS controlled by a
regulator, to enable vbus supply on the port.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-13 18:07:08 +05:30
Vivek Gautam 59025887fb phy: Add new Exynos5 USB 3.0 PHY driver
Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
The new driver uses the generic PHY framework and will interact
with DWC3 controller present on Exynos5 series of SoCs.

Also, created a new header file in linux/mfd/syscon/ for
Exynos5 SoCs and put the required PMU offset definitions
for the basic available PHYs.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-13 18:07:08 +05:30
Arnd Bergmann 3fc03f3d72 phy: kona2: use 'select GENERIC_PHY' in Kconfig
All other phy drivers use 'select', while this one is
the only one to use 'depends on'. This is not a bug, just
slightly inconsistent, so let's change it to do things the
same way as everyone else.

We may also want to turn GENERIC_PHY into a silent option
that only ever gets turned on if another driver needs it.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Matt Porter <mporter@linaro.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-12 19:02:02 +05:30
Antoine Ténart 98c3b32229 phy: exynos-mipi-video: fix check on array index
The phys array is of size EXYNOS_MIPI_PHYS_NUM. Trying to access the
index EXYNOS_MIPI_PHYS_NUM should return an error.

Fixes: 069d2e26e9 "phy: Add driver for Exynos MIPI CSIS/DSIM DPHYs"

Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-12 19:02:02 +05:30
Arnd Bergmann fe04e4297e PHY: Exynos: fix SATA phy license typo
If the license string doesn't match exactly, the module refuses to load.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-08 19:24:35 +05:30
Roger Quadros 9f1d8ed227 phy: omap-usb2: Use generic clock names "wkupclk" and "refclk"
As clocks might be named differently on multiple platforms, use a generic
name in the driver and allow device tree node to specify the platform
specific clock name.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-05-08 19:22:16 +05:30
Sergei Shtylyov 743bb387a1 phy: fix kernel oops in phy_lookup()
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:53:38 -07:00
Jean Delvare 907aa3aa8d phy: restore OMAP_CONTROL_PHY dependencies
When OMAP_CONTROL_USB was renamed to OMAP_CONTROL_PHY (commit
14da699b), its dependencies were lost in the process. Nothing in the
commit message indicates that this removal was intentional, so I think
it was by accident and the dependencies should be restored.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:53:38 -07:00
Arnd Bergmann d1481832f1 phy: exynos: fix building as a module
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2014-04-24 12:53:38 -07:00
Linus Torvalds cbda94e039 ARM: SoC: driver changes
These changes are mostly for ARM specific device drivers that either
 don't have an upstream maintainer, or that had the maintainer ask
 us to pick up the changes to avoid conflicts. A large chunk of this
 are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
 that, reset controllers for STi as well as a large rework of the
 Marvell Orion/EBU watchdog driver are notable.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIVAwUAUz/1+GCrR//JCVInAQJmfg/9GyqHatDjjUPUBjUQRIEtKgGdmQwdbDqF
 x+OrS/q5B5zYbpIWkbkt1IUYJfU+89Z5ev9jxI4rV824Nu9Y92mHPDnv+N/ptkIh
 q2OVP3bQDpWs3aEVV2B1HBNcWrNUuwco9BJu05eegEePii/cto0/wKwWIgUmrmjy
 xOLthsnp2YmeplGs7ctC6Dz8XbmELebpawejTGylARXei/SwmzB/YYDgJbYjRL2I
 WSCVa8Vo+MZaGC/yxdKVTtvsKVQenxGoMO3ojikJeRdvuVRJds48Cw+UBdzWYNeJ
 3Ssvbdx6Xltf9jy/7H0btOUgxPetZuUV+2XpbWfGu0Zr9FcGDv3q9hrxA+UYKnkY
 GIGU0otSsmpHnX5Ms3E2xnHiV/fihxA3qohqts5kYRBDr5uc+IpW6SbDymQliCGG
 OO4XmIVM3pmsqAqP3Zuseemt9CeSW2yC0XlfXkzjO74yY39c+WLBbtGI40Z5W6i0
 mM1C8RD3QSNijYCEC8eqz06BQfRImsPs+jllsnJTZaHfbOsib718uvandjfG26lN
 616YMcqq0Sp51HIQ4qW7f2dQr7vOyNqbukdkrwF5JgkY/nVki5kdciRg/yeipRy6
 Ey80a+OTq0GQljM0F2dcH/A1eHH9KsuI1L6NdSMJsl0h6guIBORPTwTw3qJ13OkR
 wpJyM+Gm+Fk=
 =u/FI
 -----END PGP SIGNATURE-----

Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver changes from Arnd Bergmann:
 "These changes are mostly for ARM specific device drivers that either
  don't have an upstream maintainer, or that had the maintainer ask us
  to pick up the changes to avoid conflicts.

  A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
  shmobile), aside from that, reset controllers for STi as well as a
  large rework of the Marvell Orion/EBU watchdog driver are notable"

* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
  Revert "net: stmmac: Add SOCFPGA glue driver"
  ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
  ARM: STi: Add reset controller support to mach-sti Kconfig
  drivers: reset: stih416: add softreset controller
  drivers: reset: stih415: add softreset controller
  drivers: reset: Reset controller driver for STiH416
  drivers: reset: Reset controller driver for STiH415
  drivers: reset: STi SoC system configuration reset controller support
  dts: socfpga: Add sysmgr node so the gmac can use to reference
  dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
  reset: Add optional resets and stubs
  ARM: shmobile: r7s72100: fix bus clock calculation
  Power: Reset: Generalize qnap-poweroff to work on Synology devices.
  dts: socfpga: Update clock entry to support multiple parents
  ARM: socfpga: Update socfpga_defconfig
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  net: stmmac: Add SOCFPGA glue driver
  watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
  drivers: cci: Export CCI PMU revision
  ...
2014-04-05 15:37:40 -07:00
Arnd Bergmann cda88c8be5 mvebu driver changes for v3.15 (incremental pull #2)
- reset
     - re-use qnap-poweroff driver for Synology NASs
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABAgAGBQJTGe0/AAoJEP45WPkGe8Znj34QALuuN/yvOykT1/qNg7fdk+C4
 Qrqcyi164KtIR1GnjaxYsDDBovreFRMLDBLhrUJnGwsS3u5TnrnGvan955GZxQ8e
 86YWlyxzJodbwrD+yK6bPNra1qArwpIQ4q5xUF/fksxMU/dLMiG2wPYQasQb9pMW
 yqm3MySNsTinave6QdiTxRzoYBwCcf1ey+mCFSkR9aLXWCFxMuK36/jHQpq7trlP
 21jB4cz8qF4eYsVNuyjadR0o4g2p2zM7RxGgZrHFHXESD2jiTrHmMv8cwlEjVMre
 0Pqv+BKI5obcMrWzCpVA2v/OUzvhMFrk0LShQVio7NQ5WUNEKPspQ3dogjnlkZKj
 6Xcc9OEYRjnAZ8i2q5g0xWoxsTLlAbDzTfmzQ03YRYtRTOxBXr20CTT2omGdJJ17
 RzCYvfc7JhGPyOjglsTibJt2plNKhQd5AzkzJFwOmF/tQkAM3LpVgjnqe/Q2Ts5L
 5BU7xQlpB2qHJgK48rRuVcpw9aIZJXtcA89oa2ebuWT6D7dJjp9W3J4WhaFzwWGy
 dxLU3WrYyiXaLoJURSHW1FaukRecubYZL9GW3Va9iN6rUn46FCVyn7RrCfHVMIXA
 Eiw4DAH2sOP7Z6Iw8NfVaU3b8ntT4vCCD3FjV3ZmWtUTsqgxBy5GdjKG9WtglAr6
 YhQ8SPTt8vSzVlzfZ4Ug
 =j/ZI
 -----END PGP SIGNATURE-----

Merge tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu into next/drivers

Merge "mvebu drivers for v3.15" from Jason Cooper:

pull request #1:

 - mvebu mbus
    - use of_find_matching_node_and_match

 - rtc
    - use PTR_ERR_OR_ZERO in isl12057
    - work around issue in mv where date returned is 2038

 - kirkwood -> mach-mvebu
    - various Kconfig oneliners to allow building kirkwood in -mvebu/

pull request #2:

 - reset
    - re-use qnap-poweroff driver for Synology NASs

* tag 'mvebu-drivers-3.15-2' of git://git.infradead.org/linux-mvebu:
  Power: Reset: Generalize qnap-poweroff to work on Synology devices.
  drivers: Enable building of Kirkwood drivers for mach-mvebu
  rtc: mv: reset date if after year 2038
  rtc: isl12057: use PTR_ERR_OR_ZERO to fix coccinelle warnings
  bus: mvebu-mbus: make use of of_find_matching_node_and_match

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2014-03-17 11:14:34 +01:00
Loc Ho 88e670fe9d PHY: add APM X-Gene SoC 15Gbps Multi-purpose PHY driver
This patch adds support for the APM X-Gene SoC 15Gbps Multi-purpose PHY.
This is the physical layer interface for the corresponding host
controller. Currently, only external clock and Gen3 SATA mode
are supported.

Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:13 +05:30
Roger Quadros 02133b9e54 phy: omap: Depend on OMAP_OCP2SCP bus driver
The OMAP_USB2 and OMAP_PIPE3 PHY devices will not be
detected if the OMAP_OCP2SCP bus driver is not present.
Make them depend on it.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:12 +05:30
Roger Quadros 56042e4e97 phy: ti-pipe3: Fix suspend/resume and module reload
Due to Errata i783, SATA breaks if its DPLL is idled. The recommeded
workaround to issue a softreset to the SATA controller doesn't seem to
work. Here we just prevent SATA DPLL from Idling and hence avoid
the issue altogether.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:11 +05:30
Roger Quadros 629138dbae phy: ti-pipe3: streamline PHY operations
Limit .power_on() and .power_off() to just control the
PHY power and not the DPLL. The DPLL will be enabled
in .init() and idled in .exit().

Don't reprogram the DPLL if it has been already locked
by the bootloader. This fixes a problem with SATA, where
it fails if SATA was used by the bootloader.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:11 +05:30
Roger Quadros 9c7f044360 phy: ti-pipe3: Don't get 'wkupclk' and 'refclk' for SATA PHY
SATA PHY doesn't need 'wkupclk; and 'refclk' so don't
try to get them for SATA PHY.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:10 +05:30
Roger Quadros 61f5467477 phy: ti-pipe3: Add SATA DPLL support
USB and SATA DPLLs need different settings. Provide
the SATA DPLL settings and use the proper DPLL settings
based on device tree node's compatible_id.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2014-03-09 12:45:10 +05:30