The flexcan driver was merged as e955cead.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested it by booting a rootfs via NFS.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The Enhanced Periodic Interrupt Timer (EPIT) is found on newer
i.MX SoCs and can be used as an alternative system timer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The core of i.MX5 series is cortex-A8, its cache line size is 64 bytes
instead of 32 bytes. Refer to the OMAP3's selection, we choose 64
bytes for i.MX5, this can increase a little bit performance when
perform cache operations.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When we call tzic_enable_wake function, the kernel will crash because
of access to an unmapped address. This is because two register
access operations forgot to add base address.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Last change I did made a big mess in function names and CONFIG names,
this patch fixes this so that the baseboard support is really built
when selected.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a follow up to
14cb0de (arm/imx/gpio: add spinlock protection)
and fixes the following build failure:
CC arch/arm/mach-imx/pcm970-baseboard.o
In file included from arch/arm/include/asm/gpio.h:6,
from include/linux/gpio.h:8,
from arch/arm/mach-imx/pcm970-baseboard.c:20:
arch/arm/plat-mxc/include/mach/gpio.h:40: error: expected specifier-qualifier-list before 'spinlock_t'
Cc: stable@kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
Carvalho de Assis modified the original driver to get it working on more recent
kernels. I modified it further to add support for i.MX25. This driver has been
tested on i.MX25 and i.MX27 based platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The GPIO registers need protection from concurrent access for operations that
are not atomic.
Cc: stable@kernel.org
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Reported-by: rpkamiak@rockwellcollins.com
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...
MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as per suggested by Sascha
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.
These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
i.MX25's OTG has the same USBCTRL registers than i.MX35 so reuse
most of the i.MX35's defines.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the standard place for this define is include/mach/mx25.h
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the clock refcounting when reparenting is used.
Boot-tested on imx51 babbage board.
Sascha pointed out a good explanation of refcounting here:
http://www.spinics.net/lists/arm-kernel/msg85879.html
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of having a platform device defined in a devices.c and register
it in the machine file allocate it dynamically. This reduces the size
of needed memory as the new function is discarded after init and only
the existing devices are created.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
As the kernel contains a copy of the GPL anyhow just get rid of the address
specification instead of fixing it.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes:
arch/arm/plat-mxc/include/mach/mxc_nand.h:25:14: error: dubious one-bit signed bitfield
arch/arm/plat-mxc/include/mach/mxc_nand.h:26:17: error: dubious one-bit signed bitfield
While at it make width unsigned, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This should be a globally available function, see
http://thread.gmane.org/gmane.linux.kernel/998881/focus=998882
Until this hits mainline create a similar function available for imx
platforms only.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This should be used instead of hard coding the corresponding platforms.
The feature test macro is needed to support different SOCs in a single
kernel image. While at it rename dma-mx1-mx2 to dma-v1 as mx25 doesn't
use it and so the mx2 part is wrong and move the header to
arch/arm/mach-imx.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
MACH_... is reserved for machine support, so use SOC as prefix, not MACH.
This introduces new symbols SOC_IMX1, SOC_IMX21 and SOC_IMX27. They are
selected by the old symbols for now. There is no substitute for MACH_MX2
as most usages of MX2 only means MX21 + MX27 but not MX25.
Later the choice about CPU and CPU family should go away and the individual
machines should select the right SOC symbol. This is a precondition to
support more than one SOC in a single kernel image.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This function is defined once for each imx family and so is in the way
when compiling a kernel for more than one SoC.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Finally all imx code should end up there, start with mach-mx2. While
touching all files rename some files to use a hyphen instead of an
underscore.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
* introduce 3 new flags to allow a more detailed configuration
of the SSI link :
IMX_SSI_NET : enable Network Mode
IMX_SSI_SYN : enable Synchronous Mode
IMX_SSI_USE_I2S_SLAVE : enable I2S Slave Mode
* new platform can use these settings without breaking actual
platforms.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds also the pin definition helpers in iomux-mx3.h
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch de-asserts the reset line that is connected to the USB
ULPI PHY on USB Host1.
This patch should be included with the original USB host enablement
set of patches of mx51 babbage hw, but was accidentily left out.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The Eyebot robot needs the OTG port in host mode on the smartbot.
Add a new board definition so we can select the usb host/device
mode at boot with the mx31moboard_baseboard boot parameter.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This fixes a regression of
7d58289 (mx1: prefix SOC specific defines with MX1_ and deprecate old names)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds USB HW initializiation code to /plat-mxc/ehci.c.
-Sets some specific PHY settings
Renames mxc_set_usbcontrol to mxc_initialize_usb_hw.
Adds new register bit defines for the USB HW on Freescale
SoCs.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Reviewed-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch is part of enabling USB for Freescale MX51 Babbage HW. This
patch updates the iomux pins for USB, and gpio line for reset the
USB hub on the MX51 Babbage HW.
This patch applies to 2.6.34-rc6.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Commit "mxc: Change gpt timer code to be more generic by using V2
instead of MX3" forgot to replace one occurence causing a build
failure.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Amit Kucheria <amit.kucheria@canonical.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Replace mx3_ with v2_ since the register layout is the same for all SoCs using
version 2 of the timer (mx25, mx31, mx37 and now mx51)
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed selection of COMMON_CLKDEV by CONFIG_ARCH_MX5. This is handled
in 03e09cd890.
arch/arm/plat-mxc/iomux-mx1-mx2.c was moved to
arch/arm/plat-mxc/iomux-v1.c in 5e2e95f520
and got bug fixed in 5c17ef878f. The bug
in arch/arm/plat-mxc/iomux-v1.c isn't present any more since
bac3fcfad5, so
arch/arm/plat-mxc/iomux-mx1-mx2.c is simply deleted.
Conflicts:
arch/arm/plat-mxc/Kconfig
arch/arm/plat-mxc/Makefile
arch/arm/plat-mxc/iomux-mx1-mx2.c
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
ARCH_MXC_IOMUX_V3 is not specific to the i.MX25 PDK platform. Thus,
ARCH_MXC_IOMUX_V3 should be selected by ARCH_MX25.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mxc_gpio_mode checks for invalid pins and so it returns zero for
success, -EINVAL for invalid pins.
While at it, remove definitions of GPIO_PORT_MAX removed as they are
unused now.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Addionally make iomux-mx*.h headers stand-alone and similar to iomux-v3
platform files should include their platform iomux header from now on.
For now iomux.h simply includes all iomux-v1 platform headers and so
provides compatibility until all files are converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX3_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX2x_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX27_H__ as header protector analogous to
<mach/mx...h>
- use tabs for indention
- fix sorting
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
- use __MACH_IOMUX_MX25_H__ as header protector analogous to
<mach/mx...h>
- remove doxygen comments
- remove #error about mach/iomux.h which is unused on mx25
- remove #ifndef __ASSEMBLY__ which is unneeded here
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Uwe Kleine-König
Fabio Estevam
Sascha Hauer
Jason Wang
Eric Bénard
Linus Torvalds
Baruch Siach
Marc Kleine-Budde
Amit Kucheria
Dinh Nguyen
Amit Kucheria
Russell King
Alberto Panizzo
Philippe Rétornaz
Wolfram Sang
Tejun Heo
Martin Fuzzey
Takashi Iwai