Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7720 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the sh3 external irq pin code. It buys us some
savings with reduced code redundancy, but the main feature with
this change is irq sense selection support for all sh3 processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides specific clock support for the SH7712.
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c. It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes old dead code:
- kill off sh7300 cpu support
- get rid of broken solution engine 7300 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out common bits from the existing exception handler for
use between SH-2/SH-2A and SH-3/4, and adds support for the SH-2/2A
exceptions.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the aforementioned CPU subtypes, and cleans
up some build issues encountered as a result.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some simple setup code for most of the CPU subtypes,
primarily simple platform device registration.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a relatively simplistic clock framework for sh. The initial goal
behind this is to clean up the arch/sh/kernel/time.c mess and to get the CPU
subtype-specific frequency setting and calculation code moved somewhere more
sensible.
This only deals with the core clocks at the moment, though it's trivial for
other drivers to define their own clocks as desired.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Magnus Damm
Magnus Damm
Andrew Murray
Yoshihiro Shimoda
Markus Brunner
Nobuhiro Iwamatsu
Yoshinori Sato
Paul Mundt
Linus Torvalds