Commit Graph

74 Commits

Author SHA1 Message Date
Harvey Harrison 441b62c1ed USB: replace remaining __FUNCTION__ occurrences
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:55 -07:00
Alan Stern 58a97ffeb2 USB: HCDs use the do_remote_wakeup flag
When a USB device is suspended, whether or not it is enabled for
remote wakeup depends on the device_may_wakeup() setting.  The setting
is then saved in the do_remote_wakeup flag.

Later on, however, the device_may_wakeup() value can change because of
user activity.  So when testing whether a suspended device is or
should be enabled for remote wakeup, we should always test
do_remote_wakeup instead of device_may_wakeup().  This patch (as1076)
makes that change for root hubs in several places.

The patch also adjusts uhci-hcd so that when an autostopped controller
is suspended, the remote wakeup setting agrees with the value recorded
in the root hub's do_remote_wakeup flag.

And the patch adjusts ehci-hcd so that wakeup events on selectively
suspended ports (i.e., the bus itself isn't suspended) don't turn on
the PME# wakeup signal.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:53 -07:00
Alan Stern 70a1c9e086 USB: remove dev->power.power_state
power.power_state is scheduled for removal.  This patch (as1053)
removes all uses of that field from drivers/usb.  Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.

Part of this patch was written by Pavel Machek.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:41 -07:00
Alan Stern 3bb1af5243 USB: EHCI: carry out port handover during each root-hub resume
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset.  This is necessary because:

	When some machines go into suspend, they remove power from
	on-board USB devices while retaining suspend current for USB
	controllers.

	The user might well unplug a USB device while the system is
	suspended and then plug it back in before resuming.

A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep.  If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.

Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-24 21:16:32 -07:00
Greg Kroah-Hartman 2c044a4803 USB: fix codingstyle issues in drivers/usb/core/*.c
Fixes a number of coding style issues in the remaining .c files in
drivers/usb/core/

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:08 -08:00
Greg Kroah-Hartman 782e70c6fc USB: mark USB drivers as being GPL only
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL.  This patch moves the USB apis to enforce that decision.

There are no known closed source USB drivers in the wild, so this patch
should cause no problems.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:07 -08:00
Greg Kroah-Hartman de6f92b9ee USB: handle idVendor of 0x0000
Some crazy devices in the wild have a vendor id of 0x0000.  If we try to
add a module alias with this id, we just can't do it due to a check in
the file2alias.c file.  Change the test to verify that both the vendor
and product ids are 0x0000 to show a real "blank" module alias.

Note, the module-init-tools package also needs to be changed to properly
generate the depmod tables.

Cc: Janusz <janumix@poczta.fm>
Cc: stable <stable@kernel.org>
Cc: Jon Masters <jcm@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:34:46 -08:00
Greg Kroah-Hartman 15147ffd57 USB: use proper call to driver_create_file
Don't try to call the "raw" sysfs_create_file when we already have a
helper function to do this kind of work for us.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-01-24 20:40:33 -08:00
Alan Stern 4a9bee8256 USB: uevent environment key fix
This patch (as1010) was written by both Kay Sievers and me.  It solves
the problem of duplicated keys in USB uevent structures by refactoring
the uevent subroutines, taking advantage of the way the hotplug core
calls uevent handlers for the device's bus and for the device's type.
Keys needed for both USB-device and USB-interface events are added in
usb_uevent(), which is the bus handler.  Keys appropriate only for
USB-device or USB-interface events are added in usb_dev_uevent() or
usb_if_uevent() respectively, the type handlers.

In addition, unnecessary tests for NULL pointers are removed as are
duplicated debugging log statements.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-11-28 13:58:35 -08:00
Linus Torvalds efefc6eb38 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
  PM: merge device power-management source files
  sysfs: add copyrights
  kobject: update the copyrights
  kset: add some kerneldoc to help describe what these strange things are
  Driver core: rename ktype_edd and ktype_efivar
  Driver core: rename ktype_driver
  Driver core: rename ktype_device
  Driver core: rename ktype_class
  driver core: remove subsystem_init()
  sysfs: move sysfs file poll implementation to sysfs_open_dirent
  sysfs: implement sysfs_open_dirent
  sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
  sysfs: make sysfs_root a regular directory dirent
  sysfs: open code sysfs_attach_dentry()
  sysfs: make s_elem an anonymous union
  sysfs: make bin attr open get active reference of parent too
  sysfs: kill unnecessary NULL pointer check in sysfs_release()
  sysfs: kill unnecessary sysfs_get() in open paths
  sysfs: reposition sysfs_dirent->s_mode.
  sysfs: kill sysfs_update_file()
  ...
2007-10-12 15:49:37 -07:00
Alan Stern d1aa3e6aa8 USB: fix race in autosuspend reschedule
This patch (as1002) fixes a small race which can occur when a driver
expects usbcore to reschedule an autosuspend request.  If the request
arrives too late, it won't be rescheduled.  The patch adds an extra
argument to autosuspend_check(), indicating that a reschedule is
needed no matter how much time has elapsed.

It also tries to avoid letting asynchronous changes to the value of
jiffies cause a delay to become negative, by caching a local copy of
the current time.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:35 -07:00
Alan Stern 271f9e68f3 USB: skip autosuspended devices during system resume
System suspends and hibernation are supposed to be as transparent as
possible.  By this reasoning, if a USB device is already autosuspended
before the system sleep begins then it should remain autosuspended
after the system wakes up.

This patch (as1001) adds a skip_sys_resume flag to the usb_device
structure and uses it to avoid waking up devices which were suspended
when a system sleep began.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:34 -07:00
Alan Stern 7108f28465 USB: don't propagate FREEZE or PRETHAW suspends
This patch (as992) fixes a recently-added bug.  During a FREEZE or
PRETHAW suspend notification, non-root devices don't actually get
suspended.  So we shouldn't tell their parent hubs that they did.

(This code path used to be skipped over, until the FREEZE/PRETHAW test
got moved out of usb_suspend_both() into generic_suspend().)

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:28 -07:00
Alan Stern 6840d2555a USB: flush outstanding URBs when suspending
This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended.  This will be true even when
CONFIG_USB_SUSPEND is not enabled.

In addition, an extra can_submit flag is added to the usb_device
structure.  That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.

It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag.  This also permits us to remove
some questionable references to the deprecated power.power_state field.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:26 -07:00
Alan Stern 5ad4f71e2f USB: move decision to ignore FREEZE events
This patch (as987) changes the way FREEZE and PRETHAW suspend events
are handled in usbcore.  The decision about whether or not to ignore
them for non-root devices is pushed down into the USB-device driver,
instead of being made in the core code.

This is appropriate, since devices exported to a virtualized guest or
over a network may indeed need to handle these types of suspend, even
though normal devices don't.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:26 -07:00
Inaky Perez-Gonzalez 72230abb21 usb: usb_probe_interface() obeys authorization
If called and the device is not authorized to be used, it won't
configure the interface and print a message saying so.

Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:07 -07:00
Kay Sievers 7eff2e7a8b Driver core: change add_uevent_var to use a struct
This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.

Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.

Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:51:01 -07:00
Nathael Pajani e5dd01154c USB: fix linked list insertion bugfix for usb core
This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.

Signed-off-by: Nathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-09-11 07:48:15 -07:00
Alan Stern 013d27f265 USB: update last_busy field correctly
This patch (as966) fixes a bug in the autosuspend code.  The last_busy
field should be updated whenever any event occurs, not just events
that cause an autosuspend or an autoresume.

This partially fixes Bugzilla #8892.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-08-22 14:27:59 -07:00
David Brownell aebdc3b450 dev_vdbg(), available with -DVERBOSE_DEBUG
This defines a dev_vdbg() call, which is enabled with -DVERBOSE_DEBUG.
When enabled, dev_vdbg() acts just like dev_dbg().  When disabled, it is a
NOP ...  just like dev_dbg() without -DDEBUG.  The specific code was moved
out of a USB patch, but lots of drivers have similar support.

That is, code can now be written to use an additional level of debug
output, selected at compile time.  Many driver authors have found this
idiom to be very useful.  A typical usage model is for "normal" debug
messages to focus on fault paths and not be very "chatty", so that those
messages can be left on during normal operation without much of a
performance or syslog load.  On the other hand "verbose" messages would be
noisy enough that they wouldn't normally be enabled; they might even affect
timings enough to change system or driver behavior.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-18 15:49:50 -07:00
Venki Pallipadi 8d6d5fd050 USB: Make usb-autosuspend timer 1 sec jiffy aligned
Make usb autosuspend timers 1sec jiffy aligned.

This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:40 -07:00
Alan Stern e7e6da9eb1 USB: Remove usages of dev->power.power_state
This patch (as922) removes all but one of the remaining vestiges of
dev->power.power_state from usbcore.  The only usage left must remain
until the deprecated "power/state" sysfs attribute is gone.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:39 -07:00
Alan Stern f07600cf9e USB: add reset_resume method
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method.  As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume.  This separation of functions makes the code clearer.

In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code.  The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.

The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements.  For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added.  The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.

A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:30 -07:00
Alan Stern 20dfdad74a USB: rework C++-style comments
This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro.  It makes the
code look cleaner, and it's easier to turn the debugging on or off.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:49 -07:00
Alan Stern 6bc6cff52e USB: add RESET_RESUME device quirk
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly.  By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them.  To get things kicked off, a quirk entry is
added for the Philips PSC805.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:47 -07:00
Alan Stern 0458d5b4c9 USB: add USB-Persist facility
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.

The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now.  But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:47 -07:00
Alan Stern b6f6436da0 USB: move bus_suspend and bus_resume method calls
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.

Their old locations were not fully correct.  For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:

	echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind

to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub.  Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.

The patch also makes a very slight change in the way devices with no
driver are handled during suspend.  Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called.  In practice this should never affect anyone.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:46 -07:00
Alan Stern 4d461095ef USB: Implement PM FREEZE and PRETHAW
This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events.  Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state.  The patch checks and avoids
doing the suspend call when possible.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:46 -07:00
Alan Stern 784a6e1cc4 USB: interface PM state
This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea.  In the end
this doesn't really matter, but it's better to be consistent.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:46 -07:00
Alan Stern ef7f6c7084 USB: more autosuspend timer stuff
This patch (as879) ties up some loose ends from an earlier patch.
These are things I didn't think to include at the time but which
clearly belonged there.

	If an autosuspend fails because driver activity races with
	the autosuspend call, restart the autosuspend timer.

	When a device is resumed by an external request, it counts
	as device activity and should update the last_busy time so
	that the next autoresume won't occur immediately.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-05-22 23:45:49 -07:00
Alan Stern 8c9862e512 USB: fix signed jiffies issue in autosuspend logic
This patch (as897) changes the autosuspend timer code to use the
standard types and macros in dealing with jiffies values.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:39 -07:00
Alan Stern 1941044aa9 USB: add "last_busy" field for use in autosuspend
This patch (as877) adds a "last_busy" field to struct usb_device, for
use by the autosuspend framework.  Now if an autosuspend call comes at
a time when the device isn't busy but hasn't yet been idle for long
enough, the timer can be set to exactly the desired value.  And we
will be ready to handle things like HID drivers, which can't maintain
a useful usage count and must rely on the time-of-last-use to decide
when to autosuspend.

The patch also makes some related minor improvements:

	Move the calls to the autosuspend condition-checking routine
	into usb_suspend_both(), which is the only place where it
	really matters.

	If the autosuspend timer is already running, don't stop
	and restart it.

	Replace immediate returns with gotos so that the optional
	debugging ouput won't be bypassed.

	If autoresume is disabled but the device is already awake,
	don't return an error for an autoresume call.

	Don't try to autoresume a device if it isn't suspended.
	(Yes, this undercuts the previous change -- so sue me.)

	Don't duplicate existing code in the autosuspend work routine.

	Fix the kerneldoc in usb_autopm_put_interface(): If an
	autoresume call fails, the usage counter is left unchanged.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:39 -07:00
Kay Sievers 9f8b17e643 USB: make usbdevices export their device nodes instead of using a separate class
o The "real" usb-devices export now a device node which can
  populate /dev/bus/usb.

o The usb_device class is optional now and can be disabled in the
  kernel config. Major/minor of the "real" devices and class devices
  are the same.

o The environment of the usb-device event contains DEVNUM and BUSNUM to
  help udev and get rid of the ugly udev rule we need for the class
  devices.

o The usb-devices and usb-interfaces share the same bus, so I used
  the new "struct device_type" to let these devices identify
  themselves. This also removes the current logic of using a magic
  platform-pointer.
  The name of the device_type is also added to the environment
  which makes it easier to distinguish the different kinds of devices
  on the same subsystem.

  It looks like this:
    add@/devices/pci0000:00/0000:00:1d.1/usb2/2-1
    ACTION=add
    DEVPATH=/devices/pci0000:00/0000:00:1d.1/usb2/2-1
    SUBSYSTEM=usb
    SEQNUM=1533
    MAJOR=189
    MINOR=131
    DEVTYPE=usb_device
    PRODUCT=46d/c03e/2000
    TYPE=0/0/0
    BUSNUM=002
    DEVNUM=004

This udev rule works as a replacement for usb_device class devices:
  SUBSYSTEM=="usb", ACTION=="add", ENV{DEVTYPE}=="usb_device", \
    NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0644"

Updated patch, which needs the device_type patches in Greg's tree.

I also got a bugzilla assigned for this. :)
  https://bugzilla.novell.com/show_bug.cgi?id=250659


Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:37 -07:00
Alan Stern 2add5229d7 USB: add power/level sysfs attribute
This patch (as874) adds another piece to the user-visible part of the
USB autosuspend interface.  The new power/level sysfs attribute allows
users to force the device on (with autosuspend off), force the device
to sleep (with autoresume off), or return to normal automatic operation.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:37 -07:00
Alan Stern eaafbc3a8a USB: Allow autosuspend delay to equal 0
This patch (as867) adds an entry for the new power/autosuspend
attribute in Documentation/ABI/testing, and it changes the behavior of
the delay value.  Now a delay of 0 means to autosuspend as soon as
possible, and negative values will prevent autosuspend.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:35 -07:00
Alan Stern 6b157c9bf3 USB: separate autosuspend from external suspend
This patch (as866) adds new entry points for external USB device
suspend and resume requests, as opposed to internally-generated
autosuspend or autoresume.  It also changes the existing
remote-wakeup code paths to use the new routines, since remote wakeup
is not the same as autoresume.

As part of the change, it turns out to be necessary to do remote
wakeup of root hubs from a workqueue.  We had been using khubd, but it
does autoresume rather than an external resume.  Using the
ksuspend_usb_wq workqueue for this purpose seemed a logical choice.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:35 -07:00
Alan Stern 718efa64e3 usbcore: move usb_autosuspend_work
This patch (as864) moves the work routine for USB autosuspend from one
source file to another.  This permits the removal of one whole global
symbol (!) and should smooth the way for more changes in the future.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 13:28:34 -07:00
Greg Kroah-Hartman 341487a837 USB: remove use of the bus rwsem, as it doesn't really protect anything.
The driver core stopped using the rwsem a long time ago, yet the USB
core still grabbed the lock, thinking it protected something.  This
patch removes that useless use.

Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: linux-usb-devel <linux-usb-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-04-27 10:57:30 -07:00
Alan Stern 19c262391c USB: export autosuspend delay in sysfs
This patch (as861) adds sysfs attributes to expose the autosuspend
delay value for each USB device.  If the user changes the delay from 0
(no autosuspend) to a positive value, an autosuspend is attempted.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-23 15:03:47 -08:00
Alan Stern b5e795f8df USB: make autosuspend delay a module parameter
This patch (as859) makes the default USB autosuspend delay a module
parameter of usbcore.  By setting the delay value at boot time, users
will be able to prevent the system from autosuspending devices which
for some reason can't handle it.

The patch also stores the autosuspend delay as a per-device value.  A
later patch will allow the user to change the value, tailoring the
delay for each individual device.  A delay value of 0 will prevent
autosuspend.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-23 15:03:46 -08:00
Greg Kroah-Hartman bb417020ba USB: refactor usb device matching and create usb_device_match
This is needed for the quirk match code.

Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-23 15:03:46 -08:00
Randy Dunlap 892705a1e1 USB: kernel-doc fixes
Fix kernel-doc warnings and in USB core.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-16 15:32:21 -08:00
Linus Torvalds c96e2c9207 Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (70 commits)
  USB: remove duplicate device id from zc0301
  USB: remove duplicate device id from usb_storage
  USB: remove duplicate device id from keyspan
  USB: remove duplicate device id from ftdi_sio
  USB: remove duplicate device id from visor
  USB: a bit more coding style cleanup
  usbcore: trivial whitespace fixes
  usb-storage: use first bulk endpoints, not last
  EHCI: fix interrupt-driven remote wakeup
  USB: switch ehci-hcd to new polling scheme
  USB: autosuspend for usb printer driver
  USB Input: Added kernel module to support all GTCO CalComp USB InterWrite School products
  USB: Sierra Wireless auto set D0
  USB: usb ethernet gadget recognizes HUSB2DEV
  USB: list atmel husb2_udc gadget controller
  USB: gadgetfs AIO tweaks
  USB: gadgetfs behaves better on userspace init bug
  USB: gadgetfs race fix
  USB: gadgetfs simplifications
  USB: gadgetfs cleanups
  ...
2007-02-07 19:23:21 -08:00
Greg Kroah-Hartman 93bacefc4c USB serial: add dynamic id support to usb-serial core
Thanks to Johannes Hölzl <johannes.hoelzl@gmx.de> for fixing a few
things and getting it all working properly.

This adds support for dynamic usb ids to the usb serial core.  The file
"new_id" will show up under the usb serial driver, not the usb driver
associated with the usb-serial driver (yeah, it can be a bit confusing
at first glance...)

This patch also modifies the USB core to allow the usb-serial core to
reuse much of the dynamic id logic.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
2007-02-07 15:44:33 -08:00
Greg Kroah-Hartman 80f745fb1b USB: add the sysfs driver name to all modules
This adds the module name to all USB drivers, if they are built into the
kernel or not.  It will show up in /sys/modules/MODULE_NAME/drivers/

Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-02-07 10:37:12 -08:00
Alan Stern 94fcda1f8a usbcore: remove unused argument in autosuspend
Thanks to several earlier patches, usb_autosuspend_device() and
usb_autoresume_device() are never called with a second argument other
than 1.  This patch (as819) removes the now-redundant argument.

It also consolidates some common code between those two routines,
putting it into a new subroutine called usb_autopm_do_device().  And
it includes a sizable kerneldoc update for the affected functions.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:53 -08:00
Alan Stern ee49fb5dc8 USB: keep count of unsuspended children
This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub.  This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.

The basic idea is simple.  There already is a usage counter in the
usb_device structure for preventing autosuspends.  The patch just
increments that counter for every unsuspended child.  There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:25:52 -08:00
Adrian Bunk 8bb22d2bda USB: make drivers/usb/core/driver.c:usb_device_match() static
usb_device_match() can now become static.

Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:37 -08:00
Stephen Hemminger d5ec1686ba USB: resume_device symbol conflict
Several functions in USB core overlap with global functions.
The linker appears to do the right thing, but it is bad practice and makes
debugging harder.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00
Alan Stern 692a186c9d USB: expand autosuspend/autoresume API
This patch (as814) adds usb_autopm_set_interface() to the autosuspend
API.  It also provides convenient wrapper routines,
usb_autopm_enable() and usb_autopm_disable(), for drivers that want
to specify directly whether autosuspend should be allowed.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-01 14:23:30 -08:00