In order to allow prefixed routes, we have to adjust how rt_gateway
is set and interpreted.
The new interpretation is:
1) rt_gateway == 0, destination is on-link, nexthop is iph->daddr
2) rt_gateway != 0, destination requires a nexthop gateway
Abstract the fetching of the proper nexthop value using a new
inline helper, rt_nexthop(), as suggested by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com>
They are always used in contexts where they can be reconstituted,
or where the finally resolved rt->rt_{src,dst} is semantically
equivalent.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "noref" argument to ip_route_input_common() is now always ignored
because we do not cache routes, and in that case we must always grab
a reference to the resulting 'dst'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer needed, as the protocol handlers now all properly
propagate the redirect back into the routing code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the SKB rather than just the IP addresses, so that policy
and other aspects can reside in ip_rt_redirect() rather then
icmp_redirect().
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer needed. TCP writes metrics, but now in it's own special
cache that does not dirty the route metrics. Therefore there is no
longer any reason to pre-cow metrics in this way.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c074da2810.
This change has several unwanted side effects:
1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
thus never create a real cached route.
2) All TCP traffic will use DST_NOCACHE and never use the routing
cache at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
DDOS synflood attacks hit badly IP route cache.
On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.
rt_garbage_collect() triggers and tries to cleanup things.
Eventually route cache is disabled but machine is under fire and might
OOM and crash.
This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.
This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)
SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
If no peer actually gets attached (either because create is zero or
the peer allocation fails) we'll trigger a BUG because we
unconditionally do an rt{,6}_peer_ptr() afterwards.
Fix this by guarding it with the proper check.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
We encode the pointer(s) into an unsigned long with one state bit.
The state bit is used so we can store the inetpeer tree root to use
when resolving the peer later.
Later the peer roots will be per-FIB table, and this change works to
facilitate that.
Signed-off-by: David S. Miller <davem@davemloft.net>
If I build with W=1, for every file that includes <net/route.h>, I get the warning
include/net/route.h: In function 'ip_route_output':
include/net/route.h:135:3: warning: initialized field overwritten [-Woverride-init]
include/net/route.h:135:3: warning: (near initialization for 'fl4') [-Woverride-init]
(This is with "gcc (Debian 4.6.3-1) 4.6.3")
A fix seems pretty trivial: move the initialization of .flowi4_tos
earlier. As far as I can tell, this has no effect on code generation.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet found that commit 813b3b5db8
(ipv4: Use caller's on-stack flowi as-is in output
route lookups.) that comes in 3.0 added a regression.
The problem appears to be that resulting flowi4_oif is
used incorrectly as input parameter to some routing lookups.
The result is that when connecting to local port without
listener if the IP address that is used is not on a loopback
interface we incorrectly assign RTN_UNICAST to the output
route because no route is matched by oif=lo. The RST packet
can not be sent immediately by tcp_v4_send_reset because
it expects RTN_LOCAL.
So, change ip_route_connect and ip_route_newports to
update the flowi4 fields that are input parameters because
we do not want unnecessary binding to oif.
To make it clear what are the input parameters that
can be modified during lookup and to show which fields of
floiw4 are reused add a new function to update the flowi4
structure: flowi4_update_output.
Thanks to Yurij M. Plotnikov for providing a bug report including a
program to reproduce the problem.
Thanks to Eric Dumazet for tracking the problem down to
tcp_v4_send_reset and providing initial fix.
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the sk_buff so that we can fetch the necessary keys from
the packet header when working with input routes.
Signed-off-by: David S. Miller <davem@davemloft.net>
First, make callers pass on-stack flowi4 to ip_route_output_gre()
so they can get at the fully resolved flow key.
Next, use that in ipgre_tunnel_xmit() to avoid the need to use
rt->rt_{dst,src}.
Signed-off-by: David S. Miller <davem@davemloft.net>
To more accurately reflect that it is purely a routing
cache lookup key and is used in no other context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
source address et al. selections, the fl4->{saddr,daddr}
assignments here are no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not used by anything in the kernel, and defined in net/route.h so
never exported to userspace.
Therefore we can safely remove it.
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are used together as a unit for route resolution
during connect(). They address the chicken-and-egg problem that
exists when ports need to be allocated during connect() processing,
yet such port allocations require addressing information from the
routing code.
It's currently more heavy handed than it needs to be, and in
particular we allocate and initialize a flow object twice.
Let the callers provide the on-stack flow object. That way we only
need to initialize it once in the ip_route_connect() call.
Later, if ip_route_newports() needs to do anything, it re-uses that
flow object as-is except for the ports which it updates before the
route re-lookup.
Also, describe why this set of facilities are needed and how it works
in a big comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
These header files are never installed to user consumption, so any
__KERNEL__ cpp checks are superfluous.
Projects should also not copy these files into their userland utility
sources and try to use them there. If they insist on doing so, the
onus is on them to sanitize the headers as needed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1018b5c016 ("Set rt->rt_iif more
sanely on output routes.") breaks rt_is_{output,input}_route.
This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".
To fix it, this does:
1) Add "int rt_route_iif;" to struct rtable
2) For input routes, always set rt_route_iif to same value as rt_iif
3) For output routes, always set rt_route_iif to zero. Set rt_iif
as it is done currently.
4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we set up the flow informations in ip_route_newports(), we take
the address informations from the the rt_key_src and rt_key_dst fields
of the rtable. They appear to be empty. So take the address
informations from rt_src and rt_dst instead. This issue was introduced
by commit 5e2b61f784 ("ipv4: Remove
flowi from struct rtable.")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Sidorenko reported for problems with local
routes left after IP addresses are deleted. It happens
when same IPs are used in more than one subnet for the
device.
Fix fib_del_ifaddr to restrict the checks for duplicate
local and broadcast addresses only to the IFAs that use
our primary IFA or another primary IFA with same address.
And we expect the prefsrc to be matched when the routes
are deleted because it is possible they to differ only by
prefsrc. This patch prevents local and broadcast routes
to be leaked until their primary IP is deleted finally
from the box.
As the secondary address promotion needs to delete
the routes for all secondaries that used the old primary IFA,
add option to ignore these secondaries from the checks and
to assume they are already deleted, so that we can safely
delete the route while these IFAs are still on the device list.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create two sets of port member accessors, one set prefixed by fl4_*
and the other prefixed by fl6_*
This will let us to create AF optimal flow instances.
It will work because every context in which we access the ports,
we have to be fully aware of which AF the flowi is anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller
Eric Dumazet
Roland Dreier
Eric Dumazet
Julian Anastasov
Steffen Klassert
OGAWA Hirofumi