When modifying PG_Dirty on cached file pages, update the new
MEM_CGROUP_STAT_DIRTY counter. This is done in the same places where
global NR_FILE_DIRTY is managed. The new memcg stat is visible in the
per memcg memory.stat cgroupfs file. The most recent past attempt at
this was http://thread.gmane.org/gmane.linux.kernel.cgroups/8632
The new accounting supports future efforts to add per cgroup dirty
page throttling and writeback. It also helps an administrator break
down a container's memory usage and provides evidence to understand
memcg oom kills (the new dirty count is included in memcg oom kill
messages).
The ability to move page accounting between memcg
(memory.move_charge_at_immigrate) makes this accounting more
complicated than the global counter. The existing
mem_cgroup_{begin,end}_page_stat() lock is used to serialize move
accounting with stat updates.
Typical update operation:
memcg = mem_cgroup_begin_page_stat(page)
if (TestSetPageDirty()) {
[...]
mem_cgroup_update_page_stat(memcg)
}
mem_cgroup_end_page_stat(memcg)
Summary of mem_cgroup_end_page_stat() overhead:
- Without CONFIG_MEMCG it's a no-op
- With CONFIG_MEMCG and no inter memcg task movement, it's just
rcu_read_lock()
- With CONFIG_MEMCG and inter memcg task movement, it's
rcu_read_lock() + spin_lock_irqsave()
A memcg parameter is added to several routines because their callers
now grab mem_cgroup_begin_page_stat() which returns the memcg later
needed by for mem_cgroup_update_page_stat().
Because mem_cgroup_begin_page_stat() may disable interrupts, some
adjustments are needed:
- move __mark_inode_dirty() from __set_page_dirty() to its caller.
__mark_inode_dirty() locking does not want interrupts disabled.
- use spin_lock_irqsave(tree_lock) rather than spin_lock_irq() in
__delete_from_page_cache(), replace_page_cache_page(),
invalidate_complete_page2(), and __remove_mapping().
text data bss dec hex filename
8925147 1774832 1785856 12485835 be84cb vmlinux-!CONFIG_MEMCG-before
8925339 1774832 1785856 12486027 be858b vmlinux-!CONFIG_MEMCG-after
+192 text bytes
8965977 1784992 1785856 12536825 bf4bf9 vmlinux-CONFIG_MEMCG-before
8966750 1784992 1785856 12537598 bf4efe vmlinux-CONFIG_MEMCG-after
+773 text bytes
Performance tests run on v4.0-rc1-36-g4f671fe2f952. Lower is better for
all metrics, they're all wall clock or cycle counts. The read and write
fault benchmarks just measure fault time, they do not include I/O time.
* CONFIG_MEMCG not set:
baseline patched
kbuild 1m25.030000(+-0.088% 3 samples) 1m25.426667(+-0.120% 3 samples)
dd write 100 MiB 0.859211561 +-15.10% 0.874162885 +-15.03%
dd write 200 MiB 1.670653105 +-17.87% 1.669384764 +-11.99%
dd write 1000 MiB 8.434691190 +-14.15% 8.474733215 +-14.77%
read fault cycles 254.0(+-0.000% 10 samples) 253.0(+-0.000% 10 samples)
write fault cycles 2021.2(+-3.070% 10 samples) 1984.5(+-1.036% 10 samples)
* CONFIG_MEMCG=y root_memcg:
baseline patched
kbuild 1m25.716667(+-0.105% 3 samples) 1m25.686667(+-0.153% 3 samples)
dd write 100 MiB 0.855650830 +-14.90% 0.887557919 +-14.90%
dd write 200 MiB 1.688322953 +-12.72% 1.667682724 +-13.33%
dd write 1000 MiB 8.418601605 +-14.30% 8.673532299 +-15.00%
read fault cycles 266.0(+-0.000% 10 samples) 266.0(+-0.000% 10 samples)
write fault cycles 2051.7(+-1.349% 10 samples) 2049.6(+-1.686% 10 samples)
* CONFIG_MEMCG=y non-root_memcg:
baseline patched
kbuild 1m26.120000(+-0.273% 3 samples) 1m25.763333(+-0.127% 3 samples)
dd write 100 MiB 0.861723964 +-15.25% 0.818129350 +-14.82%
dd write 200 MiB 1.669887569 +-13.30% 1.698645885 +-13.27%
dd write 1000 MiB 8.383191730 +-14.65% 8.351742280 +-14.52%
read fault cycles 265.7(+-0.172% 10 samples) 267.0(+-0.000% 10 samples)
write fault cycles 2070.6(+-1.512% 10 samples) 2084.4(+-2.148% 10 samples)
As expected anon page faults are not affected by this patch.
tj: Updated to apply on top of the recent cancel_dirty_page() changes.
Signed-off-by: Sha Zhengju <handai.szj@gmail.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
- Build fix for SMP=n in book3s_xics.c
- Fix for Daniel's pci_controller_ops on powernv.
- Revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- Two EEH fixes from Gavin.
- Fix for CR corruption from Sam.
- Selftest build fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
Change default key details to be more obviously unspecified.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVCMNMACgkQMUfUDdst+ylQJwCgsGHQVK4YgrIOCpIkXoc+riy1
VWkAnip86mUGKRej4jrrRvTGvm3maeTj
=/oWf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully"
* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
cdc-acm: prevent infinite loop when parsing CDC headers.
Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
usb: chipidea: otg: remove mutex unlock and lock while stop and start role
uas: Set max_sectors_240 quirk for ASM1053 devices
uas: Add US_FL_MAX_SECTORS_240 flag
uas: Allow uas_use_uas_driver to return usb-storage flags
This reverts commit feba40362b.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The usb-storage driver sets max_sectors = 240 in its scsi-host template,
for uas we do not want to do that for all devices, but testing has shown
that some devices need it.
This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and
implements support for it in uas.c, while at it it also adds support
for US_FL_MAX_SECTORS_64 to uas.c.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) mlx4 doesn't check fully for supported valid RSS hash function, fix
from Amir Vadai
2) Off by one in ibmveth_change_mtu(), from David Gibson
3) Prevent altera chip from reporting false error interrupts in some
circumstances, from Chee Nouk Phoon
4) Get rid of that stupid endless loop trying to allocate a FIN packet
in TCP, and in the process kill deadlocks. From Eric Dumazet
5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
Eric Dumazet
6) Fix two bugs in async rhashtable resizing, from Thomas Graf
7) Fix topology server listener socket namespace bug in TIPC, from Ying
Xue
8) Add some missing HAS_DMA kconfig dependencies, from Geert
Uytterhoeven
9) bgmac driver intends to force re-polling but does so by returning
the wrong value from it's ->poll() handler. Fix from Rafał Miłecki
10) When the creater of an rhashtable configures a max size for it,
don't bark in the logs and drop insertions when that is exceeded.
Fix from Johannes Berg
11) Recover from out of order packets in ppp mppe properly, from Sylvain
Rochet
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
bnx2x: really disable TPA if 'disable_tpa' option is set
net:treewide: Fix typo in drivers/net
net/mlx4_en: Prevent setting invalid RSS hash function
mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
netfilter; Add some missing default cases to switch statements in nft_reject.
ppp: mppe: discard late packet in stateless mode
ppp: mppe: sanity error path rework
net/bonding: Make DRV macros private
net: rfs: fix crash in get_rps_cpus()
altera tse: add support for fixed-links.
pxa168: fix double deallocation of managed resources
net: fix crash in build_skb()
net: eth: altera: Resolve false errors from MSGDMA to TSE
ehea: Fix memory hook reference counting crashes
net/tg3: Release IRQs on permanent error
net: mdio-gpio: support access that may sleep
inet: fix possible panic in reqsk_queue_unlink()
rhashtable: don't attempt to grow when at max_size
bgmac: fix requests for extra polling calls from NAPI
tcp: avoid looping in tcp_send_fin()
...
dell-laptop: Add support for keyboard backlight.
toshiba_acpi: Adaptive keyboard, hotkey, USB sleep and charge,
and backlight updates. Update sysfs documentation.
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
apple-gmux: lock iGP IO to protect from vgaarb changes
other: Fix typos, clear gcc warnings, clarify pr_* messages,
correct return types, update MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOzXzAAoJEKbMaAwKp364yjQH/3RJQAiemygVKTv8npk6am4W
6NjoQHwFbvbHnea1DsMBI66DgvDFuXBi04/eKoFtZiSQdt3LOWyF04VY7yPdGKT/
0yIgxMonhLk/lbBiU1PmyAsloOI4mG3zylOO+zJv66LeW0q2vjlLK7xE7AJn0dVU
hRn+Wl0YCjPzEEB4uZpKY6V0+7ys0Odxd2MeYu7pcs5DQzbvzeo4JRwUL4VtNiX9
M1I4ucBRA9jjnuNDzr4d9WtttorOOymoBYy3KFE+2QzDr5chhXTbWp6mRzwnYRvy
siOEPLzeR9jTSB4U514I1CktsCmYxvGnrGcNj1IgiY8VFujoh9j6Ndh339f8064=
=O+n4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"This series includes significant updates to the toshiba_acpi driver
and the reintroduction of the dell-laptop keyboard backlight additions
I had to revert previously. Also included are various fixes for
typos, warnings, correctness, and minor bugs.
Specifics:
dell-laptop:
- add support for keyboard backlight.
toshiba_acpi:
- adaptive keyboard, hotkey, USB sleep and charge, and backlight
updates. Update sysfs documentation.
toshiba_bluetooth:
- fix enabling/disabling loop on recent devices
apple-gmux:
- lock iGP IO to protect from vgaarb changes
other:
- Fix typos, clear gcc warnings, clarify pr_* messages, correct
return types, update MAINTAINERS"
* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
MAINTAINERS: Add me on list of Dell laptop drivers
platform: x86: dell-laptop: Add support for keyboard backlight
Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
toshiba_acpi: Fix pr_* messages from USB Sleep Functions
toshiba_acpi: Update and fix USB Sleep and Charge modes
wmi: Use bool function return values of true/false not 1/0
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
toshiba_bluetooth: Clean up *_add function and disable BT device at removal
toshiba_bluetooth: Add three new functions to the driver
toshiba_acpi: Fix the enabling of the Special Functions
toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
toshiba_acpi: Add Hotkey Event Type function and definitions
x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
apple-gmux: lock iGP IO to protect from vgaarb changes
MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
toshiba_acpi: Update events in toshiba_acpi_notify
intel-oaktrail: Fix trivial typo in comment
thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
thinkpad_acpi: signedness bugs getting current_mode
...
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlU70nMACgkQ31LbvUHyf1cYgwCfSmPhyLFmr0pGM/BxsVY7K1v6
PaEAn2+7xfZV38E6hwrGMrT42ZvKyL6r
=LHQU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
Commit 567e4b7973 ("net: rfs: add hash collision detection") had one
mistake :
RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask
This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.
In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.
Fixes: 567e4b7973 ("net: rfs: add hash collision detection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Book3S HV only (debugging aids, minor performance improvements and some
cleanups). But there are also bug fixes and small cleanups for ARM,
x86 and s390.
The task_migration_notifier revert and real fix is still pending review,
but I'll send it as soon as possible after -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVOONLAAoJEL/70l94x66DbsMIAIpZPsaqgXOC1sDEiZuYay+6
rD4n4id7j8hIAzcf3AlZdyf5XgLlr6I1Zyt62s1WcoRq/CCnL7k9EljzSmw31WFX
P2y7/J0iBdkn0et+PpoNThfL2GsgTqNRCLOOQlKgEQwMP9Dlw5fnUbtC1UchOzTg
eAMeBIpYwufkWkXhdMw4PAD4lJ9WxUZ1eXHEBRzJb0o0ZxAATJ1tPZGrFJzoUOSM
WsVNTuBsNd7upT02kQdvA1TUo/OPjseTOEoksHHwfcORt6bc5qvpctL3jYfcr7sk
/L6sIhYGVNkjkuredjlKGLfT2DDJjSEdJb1k2pWrDRsY76dmottQubAE9J9cDTk=
=OAi2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Not much has been happening in PWM land lately, so this contains mostly
minor fixes that didn't seem urgent enough for a late pull-request last
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X+q2
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Not much has been happening in PWM land lately, so this contains
mostly minor fixes that didn't seem urgent enough for a late
pull-request last cycle"
* tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Remove __init initializer for pwm_add_table()
pwm: samsung: Fix output race on disabling
pwm: mxs: Fix period divider computation
pwm: atmel-hlcdc: Add errata handling for sama5d4
pwm: pca9685: Constify struct regmap_config
pwm: imx-pwm: add explicit compatible strings and required clock properties
- correction of copy-paste stupidity while doing the cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ULmO
-----END PGP SIGNATURE-----
Merge tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
"Minor cleanup only; this could've gone in for the 4.0 merge window,
but for a copy-paste stupidity from me.
It has been in the for-next since then, and no issues reported.
- cleanup of dma_buf_export()
- correction of copy-paste stupidity while doing the cleanup"
* tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
staging: android: ion: fix wrong init of dma_buf_export_info
dma-buf: cleanup dma_buf_export() to make it easily extensible
Highlights:
- "experimental" code for managing md/raid1 across a cluster using
DLM. Code is not ready for general use and triggers a WARNING if used.
However it is looking good and mostly done and having in mainline
will help co-ordinate development.
- RAID5/6 can now batch multiple (4K wide) stripe_heads so as to
handle a full (chunk wide) stripe as a single unit.
- RAID6 can now perform read-modify-write cycles which should
help performance on larger arrays: 6 or more devices.
- RAID5/6 stripe cache now grows and shrinks dynamically. The value
set is used as a minimum.
- Resync is now allowed to go a little faster than the 'mininum' when
there is competing IO. How much faster depends on the speed of the
devices, so the effective minimum should scale with device speed to
some extent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=OHG6
-----END PGP SIGNATURE-----
Merge tag 'md/4.1' of git://neil.brown.name/md
Pull md updates from Neil Brown:
"More updates that usual this time. A few have performance impacts
which hould mostly be positive, but RAID5 (in particular) can be very
work-load ensitive... We'll have to wait and see.
Highlights:
- "experimental" code for managing md/raid1 across a cluster using
DLM. Code is not ready for general use and triggers a WARNING if
used. However it is looking good and mostly done and having in
mainline will help co-ordinate development.
- RAID5/6 can now batch multiple (4K wide) stripe_heads so as to
handle a full (chunk wide) stripe as a single unit.
- RAID6 can now perform read-modify-write cycles which should help
performance on larger arrays: 6 or more devices.
- RAID5/6 stripe cache now grows and shrinks dynamically. The value
set is used as a minimum.
- Resync is now allowed to go a little faster than the 'mininum' when
there is competing IO. How much faster depends on the speed of the
devices, so the effective minimum should scale with device speed to
some extent"
* tag 'md/4.1' of git://neil.brown.name/md: (58 commits)
md/raid5: don't do chunk aligned read on degraded array.
md/raid5: allow the stripe_cache to grow and shrink.
md/raid5: change ->inactive_blocked to a bit-flag.
md/raid5: move max_nr_stripes management into grow_one_stripe and drop_one_stripe
md/raid5: pass gfp_t arg to grow_one_stripe()
md/raid5: introduce configuration option rmw_level
md/raid5: activate raid6 rmw feature
md/raid6 algorithms: xor_syndrome() for SSE2
md/raid6 algorithms: xor_syndrome() for generic int
md/raid6 algorithms: improve test program
md/raid6 algorithms: delta syndrome functions
raid5: handle expansion/resync case with stripe batching
raid5: handle io error of batch list
RAID5: batch adjacent full stripe write
raid5: track overwrite disk count
raid5: add a new flag to track if a stripe can be batched
raid5: use flex_array for scribble data
md raid0: access mddev->queue (request queue member) conditionally because it is not set when accessed from dm-raid
md: allow resync to go faster when there is competing IO.
md: remove 'go_faster' option from ->sync_request()
...
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
This update contains:
o RENAME_WHITEOUT support
o conversion of per-cpu superblock accounting to use generic counters
o new inode mmap lock so that we can lock page faults out of truncate, hole
punch and other direct extent manipulation functions to avoid racing mmap
writes from causing data corruption
o rework of direct IO submission and completion to solve data corruption issue
when running concurrent extending DIO writes. Also solves problem of running
IO completion transactions in interrupt context during size extending AIO
writes.
o FALLOC_FL_INSERT_RANGE support for inserting holes into a file via direct
extent manipulation to avoid needing to copy data within the file
o attribute block header field overflow fix for 64k block size filesystems
o Lots of changes to log messaging to be more informative and concise when
errors occur. Also prevent a lot of unnecessary log spamming due to cascading
failures in error conditions.
o lots of cleanups and bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WE6f
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs update from Dave Chinner:
"This update contains:
- RENAME_WHITEOUT support
- conversion of per-cpu superblock accounting to use generic counters
- new inode mmap lock so that we can lock page faults out of
truncate, hole punch and other direct extent manipulation functions
to avoid racing mmap writes from causing data corruption
- rework of direct IO submission and completion to solve data
corruption issue when running concurrent extending DIO writes.
Also solves problem of running IO completion transactions in
interrupt context during size extending AIO writes.
- FALLOC_FL_INSERT_RANGE support for inserting holes into a file via
direct extent manipulation to avoid needing to copy data within the
file
- attribute block header field overflow fix for 64k block size
filesystems
- Lots of changes to log messaging to be more informative and concise
when errors occur. Also prevent a lot of unnecessary log spamming
due to cascading failures in error conditions.
- lots of cleanups and bug fixes
One thing of note is the direct IO fixes that we merged last week
after the window opened. Even though a little late, they fix a user
reported data corruption and have been pretty well tested. I figured
there was not much point waiting another 2 weeks for -rc1 to be
released just so I could send them to you..."
* tag 'xfs-for-linus-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (49 commits)
xfs: using generic_file_direct_write() is unnecessary
xfs: direct IO EOF zeroing needs to drain AIO
xfs: DIO write completion size updates race
xfs: DIO writes within EOF don't need an ioend
xfs: handle DIO overwrite EOF update completion correctly
xfs: DIO needs an ioend for writes
xfs: move DIO mapping size calculation
xfs: factor DIO write mapping from get_blocks
xfs: unlock i_mutex in xfs_break_layouts
xfs: kill unnecessary firstused overflow check on attr3 leaf removal
xfs: use larger in-core attr firstused field and detect overflow
xfs: pass attr geometry to attr leaf header conversion functions
xfs: disallow ro->rw remount on norecovery mount
xfs: xfs_shift_file_space can be static
xfs: Add support FALLOC_FL_INSERT_RANGE for fallocate
fs: Add support FALLOC_FL_INSERT_RANGE for fallocate
xfs: Fix incorrect positive ENOMEM return
xfs: xfs_mru_cache_insert() should use GFP_NOFS
xfs: %pF is only for function pointers
xfs: fix shadow warning in xfs_da3_root_split()
...
* Add Kconfig option for keeping both the 'master' and 'partition' MTDs
registered as devices. This would really make a better default if we could
do it over, as it allows a lot more flexibility in (1) determining the flash
topology of the system from user-space and (2) adding temporary partitions
at runtime (ioctl(BLKPG)). Unfortunately, this would possibly cause
user-space breakage, as it will cause renumbering of the /dev/mtdX devices.
We'll see if we can change this in the future, as there have already been a
few people looking for this feature, and I know others have just been
working around our current limitations instead of fixing them this way.
* Along with the previous change, add some additional information to sysfs, so
user-space can read the offset of each partition within its master device
SPI NOR:
* add new device tree compatible binding to represent the mostly-compatible
class of SPI NOR flash which can be detected by their extended JEDEC ID
bytes, cutting down the duplication of our ID tables
* misc. new IDs
Various other miscellaneous fixes and changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aIsV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150422' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Common MTD:
- Add Kconfig option for keeping both the 'master' and 'partition'
MTDs registered as devices. This would really make a better
default if we could do it over, as it allows a lot more flexibility
in (1) determining the flash topology of the system from user-space
and (2) adding temporary partitions at runtime (ioctl(BLKPG)).
Unfortunately, this would possibly cause user-space breakage, as it
will cause renumbering of the /dev/mtdX devices. We'll see if we
can change this in the future, as there have already been a few
people looking for this feature, and I know others have just been
working around our current limitations instead of fixing them this
way.
- Along with the previous change, add some additional information to
sysfs, so user-space can read the offset of each partition within
its master device
SPI NOR:
- add new device tree compatible binding to represent the
mostly-compatible class of SPI NOR flash which can be detected by
their extended JEDEC ID bytes, cutting down the duplication of our
ID tables
- misc. new IDs
Various other miscellaneous fixes and changes"
* tag 'for-linus-20150422' of git://git.infradead.org/linux-mtd: (53 commits)
mtd: spi-nor: Add support for Macronix mx25u6435f serial flash
mtd: spi-nor: Add support for Winbond w25q64dw serial flash
mtd: spi-nor: add support for the Winbond W25X05 flash
mtd: spi-nor: support en25s64 device
mtd: m25p80: bind to "nor-jedec" ID, for auto-detection
Documentation: devicetree: m25p80: add "nor-jedec" binding
mtd: Make MTD tests cancelable
mtd: mtd_oobtest: Fix bitflip_limit usage in test case 3
mtd: docg3: remove invalid __exit annotations
mtd: fsl_ifc_nand: use msecs_to_jiffies for time conversion
mtd: atmel_nand: don't map the ROM table if no pmecc table offset in DT
mtd: atmel_nand: add a definition for the oob reserved bytes
mtd: part: Remove partition overlap checks
mtd: part: Add sysfs variable for offset of partition
mtd: part: Create the master device node when partitioned
mtd: ts5500_flash: Fix typo in MODULE_DESCRIPTION in ts5500_flash.c
mtd: denali: Disable sub-page writes in Denali NAND driver
mtd: pxa3xx_nand: cleanup wait_for_completion handling
mtd: nand: gpmi: Check for scan_bbt() error
mtd: nand: gpmi: fixup return type of wait_for_completion_timeout
...
An MPLS network is a single trust domain where the edges must be in
control of what labels make their way into the core. The simplest way
of ensuring this is for the edge device to always impose the labels,
and not allow forward labeled traffic from untrusted neighbours. This
is achieved by allowing a per-device configuration of whether MPLS
traffic input from that interface should be processed or not.
To be secure by default, the default state is changed to MPLS being
disabled on all interfaces unless explicitly enabled and no global
option is provided to change the default. Whilst this differs from
other protocols (e.g. IPv6), network operators are used to explicitly
enabling MPLS forwarding on interfaces, and with the number of links
to the MPLS core typically fairly low this doesn't present too much of
a burden on operators.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were expecting to sit on this branch through most of the merge window since
the contents was merged into our tree late, but we ended up sitting on all of
our contents so it can go in with the rest.
The contents here is:
- A large branch of cleanups of the CM/PRM blocks on OMAP.
- A couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- A branch with DT updates for Freescale i.MX. including some shuffling from
.dts to .dtsi (include) files that causes a little churn.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ssbK
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Olof Johansson:
"We were expecting to sit on this branch through most of the merge
window since the contents was merged into our tree late, but we ended
up sitting on all of our contents so it can go in with the rest.
The contents here is:
- a large branch of cleanups of the CM/PRM blocks on OMAP.
- a couple of patches plumbing up CM/PRM on OMAP5 and DRA7.
- a branch with DT updates for Freescale i.MX. including some
shuffling from .dts to .dtsi (include) files that causes a little
churn"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (78 commits)
ARM: OMAP2+: Fix booting with configs that don't have MFD_SYSCON
ARM: OMAP4+: control: add support for initializing control module via DT
ARM: dts: dra7: add minimal l4 bus layout with control module support
ARM: dts: omap5: add minimal l4 bus layout with control module support
ARM: OMAP4+: control: remove support for legacy pad read/write
ARM: OMAP4: display: convert display to use syscon for dsi muxing
ARM: dts: omap4: add minimal l4 bus layout with control module support
ARM: dts: am4372: add minimal l4 bus layout with control module support
ARM: dts: am43xx-epos-evm: fix pinmux node layout
ARM: dts: am33xx: add minimal l4 bus layout with control module support
ARM: dts: omap3: add minimal l4 bus layout with control module support
ARM: dts: omap24xx: add minimal l4 bus layout with control module support
ARM: OMAP2+: control: add syscon support for register accesses
ARM: OMAP2+: id: cache omap_type value
ARM: OMAP2+: control: remove API for getting control module base address
ARM: OMAP2+: clock: add low-level support for regmap
ARM: OMAP4+: PRM: get rid of cpu_is_omap44xx calls from interrupt init
ARM: OMAP4+: PRM: setup prm_features from the PRM init time flags
ARM: OMAP2+: CM: move SoC specific init calls within a generic API
ARM: OMAP4+: PRM: determine prm_device_inst based on DT compatibility
...
The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This includes some
cleanups and removal of code, and the final flip of config dependencies
- Shmobile has several platforms that are going multiplatform, but this
branch also contains a bunch of cleanups that they weren't able to keep
separate in a good way. THere's also a removal of one of their SoCs and the
corresponding boards (sh7372 and mackerel).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vq4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code changes from Olof Johansson:
"The changes here belong to two main platforms:
- Atmel At91 is flipping the bit and going multiplatform. This
includes some cleanups and removal of code, and the final flip of
config dependencies
- Shmobile has several platforms that are going multiplatform, but
this branch also contains a bunch of cleanups that they weren't
able to keep separate in a good way. THere's also a removal of one
of their SoCs and the corresponding boards (sh7372 and mackerel)"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: at91/pm: move AT91_MEMCTRL_* to pm.h
ARM: at91/pm: move the standby functions to pm.c
ARM: at91: fix pm_suspend.S compilation when ARMv6 is selected
ARM: at91: add a Kconfig dependency on multi-platform
ARM: at91: drop AT91_TIMER_HZ
ARM: at91: remove hardware.h
ARM: at91: remove SoC headers
ARM: at91: remove useless mach/cpu.h
ARM: at91: remove unused headers
ARM: at91: switch at91_dt_defconfig to multiplatform
ARM: at91: switch to multiplatform
ARM: shmobile: r8a7778: enable multiplatform target
ARM: shmobile: bockw: add sound to DT
ARM: shmobile: r8a7778: add sound to DT
ARM: shmobile: bockw: add devices hooked up to i2c0 to DT
DT: i2c: add trivial binding for OKI ML86V7667 video decoder
ARM: shmobile: r8a7778: common clock framework CPG driver
ARM: shmobile: bockw dts: set extal clock frequency
ARM: shmobile: bockw dts: Move Ethernet node to BSC
ARM: shmobile: r8a73a4: Remove legacy code
...
Driver updates for v4.1. Some of these are for drivers/soc, where we find more
and more SoC-specific drivers these days. Some are for other driver subsystems
where we have received acks from the appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level interface
for talking to the system PMIC over a dedicated I2C interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used for CPU
up/down and needs to be in a shared location for arm/arm64 common code.
- Cleanup of ARM-CCI PMU code.
- Anoter set of cleanusp to the OMAP GPMC code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzKYAAoJEIwa5zzehBx3UJ8P/37OA1Qc5vR/Kyc8WlhPlNFV
MRE7ajM+FMd/Islt4nVNKATK2o3peCTPrqcniDfdPmN2dM1l4LvdeIvkIhKpB09h
ovmYTZLI/AIbbkttWybGO4lVpFeATxX5N91XXBHvbqkMh6N6ppiYWZUYeJs9EhAw
2YKykfDCTjKykS+m4YThXw9SCF/6mkCvaBL2VAuKnoV0ygjQD109Fce/irKaAoyw
L2w4PXOimUk8RshTx3afKCgTotMS0e9JWjKjvDO5M2KAD8DHm7PDRMmRVzA2sSFG
E2BCfh2DTjzJjdfRYsTd1bYnWzvakX1CzLjiFv+Sb0ctanoZdiDtJIDpX+vSXZ+D
W7i0yhEWIrr2qaZOyXR8znw8BhzdVZhmT+O76N47HvzMb5JUkaZBhEUBfUyeDbk+
YhEwz1G+YxT+fg7bBrxa3vLzOJ2pUwVJPITNuPKr6eZJmaBqgx2M7xXs3KyIJX1Y
AV9eUs2uNCyonawO6xXRhlUKREKL1TftqNXfLj7MYg6AaoVqK0qNRfuCdhMFhMdN
88QCl/qpPtIDL6ZnxlOejs30+DCH1QPx6+GhxkUlVlF1j/2ZM0cK2cj3tggDbNvN
uSy/g5pYDp62Az8UCoNXmKdnb4UONigb7k49naZbW/9CGRp1rrmUdzPUAm0tHMBT
HsH7ms+nHAZHrAlNvvtP
=/sWo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for v4.1. Some of these are for drivers/soc, where we
find more and more SoC-specific drivers these days. Some are for
other driver subsystems where we have received acks from the
appropriate maintainers.
The larger parts of this branch are:
- MediaTek support for their PMIC wrapper interface, a high-level
interface for talking to the system PMIC over a dedicated I2C
interface.
- Qualcomm SCM driver has been moved to drivers/firmware. It's used
for CPU up/down and needs to be in a shared location for arm/arm64
common code.
- cleanup of ARM-CCI PMU code.
- another set of cleanusp to the OMAP GPMC code"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (43 commits)
soc/mediatek: Remove unused variables
clocksource: atmel-st: select MFD_SYSCON
soc: mediatek: Add PMIC wrapper for MT8135 and MT8173 SoCs
arm-cci: Fix CCI PMU event validation
arm-cci: Split the code for PMU vs driver support
arm-cci: Get rid of secure transactions for PMU driver
arm-cci: Abstract the CCI400 PMU specific definitions
arm-cci: Rearrange code for splitting PMU vs driver code
drivers: cci: reject groups spanning multiple HW PMUs
ARM: at91: remove useless include
clocksource: atmel-st: remove mach/hardware dependency
clocksource: atmel-st: use syscon/regmap
ARM: at91: time: move the system timer driver to drivers/clocksource
ARM: at91: properly initialize timer
ARM: at91: at91rm9200: remove deprecated arm_pm_restart
watchdog: at91rm9200: implement restart handler
watchdog: at91rm9200: use the system timer syscon
mfd: syscon: Add atmel system timer registers definition
ARM: at91/dt: declare atmel,at91rm9200-st as a syscon
soc: qcom: gsbi: Add support for ADM CRCI muxing
...
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
Our SoC branch usually contains expanded support for new SoCs and other core
platform code. In this case, that includes:
- Support for the new Annapurna Labs "Alpine" platform
- A rework greatly simplifying adding new platform support to the MCPM
subsystem (Multi-cluster power management)
- Cpuidle and PM improvements for Exynos3250
- Misc updates for Renesas, OMAP, Meson, i.MX. Some of these could have
gone in other branches but ended up here for various reasons.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tcGs
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Our SoC branch usually contains expanded support for new SoCs and
other core platform code. In this case, that includes:
- support for the new Annapurna Labs "Alpine" platform
- a rework greatly simplifying adding new platform support to the
MCPM subsystem (Multi-cluster power management)
- cpuidle and PM improvements for Exynos3250
- misc updates for Renesas, OMAP, Meson, i.MX. Some of these could
have gone in other branches but ended up here for various reasons"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
ARM: alpine: add support for generic pci
ARM: Exynos: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: migrate DCSCB to the new MCPM backend abstraction
ARM: vexpress: DCSCB: tighten CPU validity assertion
ARM: vexpress: migrate TC2 to the new MCPM backend abstraction
ARM: MCPM: move the algorithmic complexity to the core code
ARM: EXYNOS: allow cpuidle driver usage on Exynos3250 SoC
ARM: EXYNOS: add AFTR mode support for Exynos3250
ARM: EXYNOS: add code for setting/clearing boot flag
ARM: EXYNOS: fix CPU1 hotplug on Exynos3250
ARM: S3C64XX: Use fixed IRQ bases to avoid conflicts on Cragganmore
ARM: cygnus: fix const declaration bcm_cygnus_dt_compat
ARM: DRA7: hwmod: Fix the hwmod class for GPTimer4
ARM: DRA7: hwmod: Add data for GPTimers 13 through 16
ARM: EXYNOS: Remove left over 'extra_save'
ARM: EXYNOS: Constify exynos_pm_data array
ARM: EXYNOS: use static in suspend.c
ARM: EXYNOS: Use platform device name as power domain name
ARM: EXYNOS: add support for async-bridge clocks for pm_domains
ARM: omap-device: add missed callback for suspend-to-disk
...
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for -stable as
well.
Contents here is as usual not all that controversial:
- A handful of randconfig fixes from Arnd, in particular for older Samsung
platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- Misc minor fixes for OMAP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o/4N
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's the usual "low-priority fixes that didn't make it into the last
few -rcs, with a twist: We had a fixes pull request that I didn't send
in time to get into 4.0, so we'll send some of them to Greg for
-stable as well.
Contents here is as usual not all that controversial:
- a handful of randconfig fixes from Arnd, in particular for older
Samsung platforms
- Exynos fixes, !SMP building, DTS updates for MMC and lid switch
- Kbuild fix to create output subdirectory for DTB files
- misc minor fixes for OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
ARM: DRA7: Enable Cortex A15 errata 798181
ARM: dts: am57xx-beagle-x15: Add thermal map to include fan and tmp102
ARM: dts: DRA7: Add bandgap and related thermal nodes
bus: ocp2scp: SYNC2 value should be changed to 0x6
ARM: dts: am4372: Add "ti,am437x-ocp2scp" as compatible string for OCP2SCP
ARM: OMAP2+: remove superfluous NULL pointer check
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP4: remove dead kconfig option OMAP4_ERRATA_I688
MAINTAINERS: add OMAP defconfigs under OMAP SUPPORT
ARM: OMAP1: PM: fix some build warnings on 1510-only Kconfigs
ARM: cns3xxx: don't export static symbol
ARM: S3C24XX: avoid a Kconfig warning
ARM: S3C24XX: fix header file inclusions
ARM: S3C24XX: fix building without PM_SLEEP
ARM: S3C24XX: use SAMSUNG_WAKEMASK for s3c2416
...
The watchdog has been reworked to use the same DT node as the timer.
This change is updating the device tree doc accordingly.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HpGw
-----END PGP SIGNATURE-----
Merge tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a new frontend driver for new ATSC devices: lgdt3306a
- a new sensor driver: ov2659
- a new platform driver: xilinx
- the m88ts2022 tuner driver was merged at ts2020 driver
- the media controller gained experimental support for DVB and hybrid
devices
- lots of random cleanups, fixes and improvements on media drivers
* tag 'media/v4.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (404 commits)
[media] uvcvideo: add support for VIDIOC_QUERY_EXT_CTRL
[media] uvcvideo: fix cropcap v4l2-compliance failure
[media] media: omap3isp: remove unused clkdev
[media] coda: Add tracing support
[media] coda: drop dma_sync_single_for_device in coda_bitstream_queue
[media] coda: fix fill bitstream errors in nonstreaming case
[media] coda: call SEQ_END when the first queue is stopped
[media] coda: fail to start streaming if userspace set invalid formats
[media] coda: remove duplicate error messages for buffer allocations
[media] coda: move parameter buffer in together with context buffer allocation
[media] coda: allocate bitstream buffer from REQBUFS, size depends on the format
[media] coda: allocate per-context buffers from REQBUFS
[media] coda: use strlcpy instead of snprintf
[media] coda: bitstream payload is unsigned
[media] coda: fix double call to debugfs_remove
[media] coda: check kasprintf return value in coda_open
[media] coda: bitrate can only be set in kbps steps
[media] v4l2-mem2mem: no need to initialize b in v4l2_m2m_next_buf and v4l2_m2m_buf_remove
[media] s5p-mfc: set allow_zero_bytesused flag for vb2_queue_init
[media] coda: set allow_zero_bytesused flag for vb2_queue_init
...
Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog below.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IMEACgkQMUfUDdst+yloDQCfbyIRL23WVAn9ckQse/y8gbjB
OT4AoKTJbwndDP9Kb/lrj2tjd9QjNVrC
=xhen
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patchset for 4.1-rc1.
Lots of different driver subsystem updates here, nothing major, full
details are in the shortlog.
All of this has been in linux-next for a while"
* tag 'char-misc-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (133 commits)
mei: trace: remove unused TRACE_SYSTEM_STRING
DTS: ARM: OMAP3-N900: Add lis3lv02d support
Documentation: DT: lis302: update wakeup binding
lis3lv02d: DT: add wakeup unit 2 and wakeup threshold
lis3lv02d: DT: use s32 to support negative values
Drivers: hv: hv_balloon: correctly handle num_pages>INT_MAX case
Drivers: hv: hv_balloon: correctly handle val.freeram<num_pages case
mei: replace check for connection instead of transitioning
mei: use mei_cl_is_connected consistently
mei: fix mei_poll operation
hv_vmbus: Add gradually increased delay for retries in vmbus_post_msg()
Drivers: hv: hv_balloon: survive ballooning request with num_pages=0
Drivers: hv: hv_balloon: eliminate jumps in piecewiese linear floor function
Drivers: hv: hv_balloon: do not online pages in offline blocks
hv: remove the per-channel workqueue
hv: don't schedule new works in vmbus_onoffer()/vmbus_onoffer_rescind()
hv: run non-blocking message handlers in the dispatch tasklet
coresight: moving to new "hwtracing" directory
coresight-tmc: Adding a status interface to sysfs
coresight: remove the unnecessary configuration coresight-default-sink
...
Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some odd
reason, but Peter is working on fixing that. If not, I'll send a revert
for the offending patch, but I have faith that Peter can address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices in
the future.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlU2IcUACgkQMUfUDdst+ylFqACcC8LPhFEZg9aHn0hNUoqGK3rE
5dUAnR4b8r/NYqjVoE9FJZgZfB/TqVi1
=lyN/
-----END PGP SIGNATURE-----
Merge tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here's the big tty/serial driver update for 4.1-rc1.
It was delayed for a bit due to some questions surrounding some of the
console command line parsing changes that are in here. There's still
one tiny regression for people who were previously putting multiple
console command lines and expecting them all to be ignored for some
odd reason, but Peter is working on fixing that. If not, I'll send a
revert for the offending patch, but I have faith that Peter can
address it.
Other than the console work here, there's the usual serial driver
updates and changes, and a buch of 8250 reworks to try to make that
driver easier to maintain over time, and have it support more devices
in the future.
All of these have been in linux-next for a while"
* tag 'tty-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
n_gsm: Drop unneeded cast on netdev_priv
sc16is7xx: expose RTS inversion in RS-485 mode
serial: 8250_pci: port failed after wakeup from S3
earlycon: 8250: Document kernel command line options
earlycon: 8250: Fix command line regression
earlycon: Fix __earlycon_table stride
tty: clean up the tty time logic a bit
serial: 8250_dw: only get the clock rate in one place
serial: 8250_dw: remove useless ACPI ID check
dmaengine: hsu: move memory allocation to GFP_NOWAIT
dmaengine: hsu: remove redundant pieces of code
serial: 8250_pci: add Intel Tangier support
dmaengine: hsu: add Intel Tangier PCI ID
serial: 8250_pci: replace switch-case by formula for Intel MID
serial: 8250_pci: replace switch-case by formula
tty: cpm_uart: replace CONFIG_8xx by CONFIG_CPM1
serial: jsm: some off by one bugs
serial: xuartps: Fix check in console_setup().
serial: xuartps: Get rid of register access macros.
serial: xuartps: Fix iobase use.
...
drivers and updates to existing ones for feature enhancements and bug
fixes. There is more churn than usual in the framework core due to the
change to introduce per-user unique struct clk pointers in 4.0. This
caused several regressions to surface, some of which were sent as fixes
to 4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers. Additionally the common clk-divider code recieved
several fixes to the way it rounds rates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNcIIAAoJEKI6nJvDJaTU3a8QAM+fjhDMY5xpI6VIbxZaA2aR
VUofw9/rdAtP1UdwtlSKBvCqpwwqt/U7zlMWU9v+UvTjYdHIf9SIDQoJnd+uEtwL
roz/kNeB7WOVyxwbTJ2B5fjvPSN+mq8Rm8ANDcL8ZOGxxtt2Mip1IWMAlx2XUnwG
tYZhB7EfKzLHZRblOdn2Q4U/4T+KXOFTSO+Gb9o2J0I2sJLI0NRXhcl9Fcoo8KVz
G0ACWa0F1WKsbqzBATnhtYiKkuC3BeiS2eMuTVTlkP+Gd6YQ2f1zWLeBfXEiPGZb
q0p/qTrUFLHbRoJMMuWaUfaBxb8PeUfM6yllxrzvRxPJU25pbj8OW/O5ZAe9xP8G
S17sQ2nhEoWZW9hqbuA39IcLGa6RjT+TD+z3kmXQ9ZvCVDN2Oqqb/4ZNViwAvQq7
t67EfV7hGXty3Q58tS4XE9hHfwY+9YqMDLNIS/ED+hP8rcxTmiLlAIyk+qbT3b0l
Q+375Ar7iCgihPPHYxeM5Qe1+Vsfh4NjR9thdAbT245MB3f90ULb+GNP/izUDOgA
c/Ot6pStVFEUxTol6RlcLb85PugzrkoBOF/8ZLySdMLhALjPwaFcQZ1sFdcKUKlE
tt7sZKQgbbCfqYGS9K264uUfWbdmZh05zhtkH0xUjyQpyIcnrYQsSIIEEnlbYnPp
0D55nooSGROKeud+gyrx
=2LMr
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.0 are mostly new clock
drivers and updates to existing ones for feature enhancements and bug
fixes.
There is more churn than usual in the framework core due to the change
to introduce per-user unique struct clk pointers in 4.0. This caused
several regressions to surface, some of which were sent as fixes to
4.0. New generic clock drivers were added for GPIO- and PWM-based
clock controllers.
Additionally the common clk-divider code recieved several fixes to the
way it rounds rates"
* tag 'clk-for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (91 commits)
clk: check ->determine/round_rate() return value in clk_calc_new_rates
clk: at91: usb: propagate rate modification to the parent clk
clk: samsung: exynos4: Disable ARMCLK down feature on Exynos4210 SoC
clk: don't use __initconst for non-const arrays
clk: at91: change to using endian agnositc IO
clk: clk-gpio-gate: Fix active low
clk: Add PWM clock driver
clk: Add clock driver for mb86s7x
clk: pxa: pxa3xx: add missing os timer clock
clk: tegra: Use the proper parent for plld_dsi
clk: tegra: Use generic tegra_osc_clk_init() on Tegra114
clk: tegra: Model oscillator as clock
clk: tegra: Add peripheral registers for bank Y
clk: tegra: Register the proper number of resets
clk: tegra: Remove needless initializations
clk: tegra: Use consistent indentation
clk: tegra: Various whitespace cleanups
clk: tegra: Enable HDA to HDMI clocks on Tegra124
clk: tegra: Fix a bunch of sparse warnings
clk: tegra: Fix typo tabel -> table
...
Some PowerNV systems include a hardware random-number generator.
This HWRNG is present on POWER7+ and POWER8 chips and is capable of
generating one 64-bit random number every microsecond. The random
numbers are produced by sampling a set of 64 unstable high-frequency
oscillators and are almost completely entropic.
PAPR defines an H_RANDOM hypercall which guests can use to obtain one
64-bit random sample from the HWRNG. This adds a real-mode
implementation of the H_RANDOM hypercall. This hypercall was
implemented in real mode because the latency of reading the HWRNG is
generally small compared to the latency of a guest exit and entry for
all the threads in the same virtual core.
Userspace can detect the presence of the HWRNG and the H_RANDOM
implementation by querying the KVM_CAP_PPC_HWRNG capability. The
H_RANDOM hypercall implementation will only be invoked when the guest
does an H_RANDOM hypercall if userspace first enables the in-kernel
H_RANDOM implementation using the KVM_CAP_PPC_ENABLE_HCALL capability.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
At present, dma_buf_export() takes a series of parameters, which
makes it difficult to add any new parameters for exporters, if required.
Make it simpler by moving all these parameters into a struct, and pass
the struct * as parameter to dma_buf_export().
While at it, unite dma_buf_export_named() with dma_buf_export(), and
change all callers accordingly.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Pull drm updates from Dave Airlie:
"Highlights:
Core:
- Virtual GEM layer merged, this has been around for a long time, and
it provides a software backed device that allows userspace to use
it as a GEM shared memory handler. This makes it a lot easier to
do certain things when you have no GPU but still have to deal with
DRI expectations.
- atomic helper updates.
- framebuffer modifier interface added.
- i2c over auxch displayport fixes.
- fb width/height confusion fixes.
- new driver for ps8622/ps8625 bridge chips
- lots of new panels
i915:
- more plane atomic conversion
- vGPU guest support for XenGT
- Skylake workarounds and fixes
- Y-tiling support
- work on dynamic pagetable allocation
- EU count report param for gen9+
- CHV fixes (no longer prelim)
- remove ilk rc6
- frontbuffer tracking for fbc
- Displayport link rate refactoring
- sprite colorkey refactor
radeon:
- Displayport MST support (not enabled by default)
- non-ATOM native hw auxch support (DCE5+)
- output csc support
- new queries for userspace debug support
- new VCE packet
nouveau:
- gk20a iommu support
- gm107 graphics support
- more gm20x bringup (waiting on signed nvidia fw).
amdkfd:
- multiple kgd instance support
- use 64-bit time accessors
msm:
- stolen memory support
- DSI and dual-DSI support
- snapdragon 410 support
exynos:
- cleanups for atomic and pageflip
imx-drm:
- more media-bus formats
- TV output prep
- drm panel support
tegra:
- hw vblank counter using host1x syncpoints
omap:
- universal plane support
- prep work for atomic modesetting
rcar-du:
- ported to atomic modesetting
atmel-hlcdc:
- ported to atomic modesetting
- added suspend/resume support
sti:
- ported to atomic modesetting
dwhdmi:
- more compliant audio support
- update rockchip phy support
tda998x:
- DT probing for attached crtcs
- simplified EDID reading
rockchip:
- fixes
adv7511:
- fixes"
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (689 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
drm/i915: Dont enable CS_PARSER_ERROR interrupts at all
drm/i915: Move drm_framebuffer_unreference out of struct_mutex for takeover
drm: fix trivial typo mistake
drm: Make integer overflow checking cover universal cursor updates (v2)
drm/nouveau/bios: fix fetching from acpi on certain systems
drm/nouveau/gr/gm206: initial init+ctx code
drm/nouveau/ce/gm206: enable support via gm204 code
drm/nouveau/fifo/gm206: enable support via gm204 code
drm/nouveau/gr/gm204: initial init+ctx code
drm/nouveau: support for buffer moves via MaxwellDmaCopyA
drm/nouveau/ce/gm204: initial support
drm/nouveau: add support for gm20x fifo channels
drm/nouveau/fifo/gm204: initial support
drm/nouveau/gr/gk104-: prevent reading non-existent regs in intr handler
drm/nouveau/gr/gm107: very slightly demagic part of attrib cb setup
drm/nouveau/gr/gk104-: correct crop/zrop num_active_fbps setting
drm/nouveau/gr/gf100-: add symbolic names for classes
drm/nouveau/gr/gm107: support tpc "strand" ctxsw in gpccs ucode
drm/nouveau/gr/gf100-: support mmio access with gpc offset from gpccs ucode
...
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
Merge a set of fixes that we missed sending in before v4.0 release. These
will also be sent to -stable.
* fixes: (659 commits)
ARM: at91/dt: sama5d3 xplained: add phy address for macb1
kbuild: Create directory for target DTB
ARM: mvebu: Disable CPU Idle on Armada 38x
arm64: juno: Fix misleading name of UART reference clock
ARM: dts: sunxi: Remove overclocked/overvoltaged OPP
ARM: dts: sun4i: a10-lime: Override and remove 1008MHz OPP setting
ARM: socfpga: dts: fix spi1 interrupt
ARM: dts: Fix gpio interrupts for dm816x
ARM: dts: dra7: remove ti,hwmod property from pcie phy
ARM: EXYNOS: Fix build breakage cpuidle on !SMP
ARM: OMAP: dmtimer: disable pm runtime on remove
ARM: OMAP: dmtimer: check for pm_runtime_get_sync() failure
ARM: dts: fix lid and power pin-functions for exynos5250-spring
ARM: dts: fix mmc node updates for exynos5250-spring
ARM: OMAP2+: Fix socbus family info for AM33xx devices
ARM: dts: omap3: Add missing dmas for crypto
+ Linux 4.0-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
The doc refers to Documentation/devicetree/bindings/video/video-ports.txt
which does not exist. The documentation seems to be outdated and wants to
refer to Documentation/devicetree/bindings/graph.txt instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>