Commit Graph

1378 Commits

Author SHA1 Message Date
Spoorthi Ravishankar Koppad ad4a6795e0 Bluetooth: Add support for utilizing Fast Advertising Interval
Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.

A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).

         - Non-Discoverable Mode
         - Non-Connectable Mode
         - Limited Discoverable Mode
         - General Discoverable Mode

Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-09-05 17:27:21 +02:00
Marcel Holtmann 58a96fc353 Bluetooth: Add debug setting for changing minimum encryption key size
For testing and qualification purposes it is useful to allow changing
the minimum encryption key size value that the host stack is going to
enforce. This adds a new debugfs setting min_encrypt_key_size to achieve
this functionality.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2019-08-17 13:54:40 +03:00
Spoorthi Ravishankar Koppad 302975cba1 Bluetooth: Add support for LE ping feature
Changes made to add HCI Write Authenticated Payload timeout
command for LE Ping feature.

As per the Core Specification 5.0 Volume 2 Part E Section 7.3.94,
the following code changes implements
HCI Write Authenticated Payload timeout command for LE Ping feature.

Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06 15:29:12 +02:00
João Paulo Rechi Vita f80c5dad7b Bluetooth: Ignore CC events not matching the last HCI command
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.

The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.

This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.

Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64)                                  0.352340
= Note: Bluetooth subsystem version 2.22                               0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0)               [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84                                 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm)                      [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14             {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14                  {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14                {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1       {0x0003} [hci0] 27.302310
        Address type: 0x06
          LE Public
          LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6   #1 [hci0] 27.302496
        Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4                 #2 [hci0] 27.419117
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7  #3 [hci0] 27.419244
        Type: Active (0x01)
        Interval: 11.250 msec (0x0012)
        Window: 11.250 msec (0x0012)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #4 [hci0] 27.420131
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2      #5 [hci0] 27.420259
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                 #6 [hci0] 27.420969
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4                 #7 [hci0] 27.421983
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4        {0x0003} [hci0] 27.422059
      Start Discovery (0x0023) plen 1
        Status: Success (0x00)
        Address type: 0x06
          LE Public
          LE Random
@ MGMT Event: Discovering (0x0013) plen 2             {0x0003} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0002} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2             {0x0001} [hci0] 27.422067
        Address type: 0x06
          LE Public
          LE Random
        Discovery: Enabled (0x01)

Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-05-05 19:29:04 +02:00
Marcel Holtmann d5bb334a8e Bluetooth: Align minimum encryption key size for LE and BR/EDR connections
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
2019-04-25 06:18:07 -07:00
Matthias Kaehlcke 7a0e5b15ca Bluetooth: Add quirk for reading BD_ADDR from fwnode property
Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve
the public Bluetooth address from the firmware node property
'local-bd-address'. If quirk is set and the property does not exist
or is invalid the controller is marked as unconfigured.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26 10:08:26 +01:00
Rajat Jain e2bef3847e Bluetooth: Allow driver specific cmd timeout handling
Add a hook to allow the BT driver to do device or command specific
handling in case of timeouts. This is to be used by Intel driver to
reset the device after certain number of timeouts.

Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-01-25 08:46:32 +01:00
Matthias Kaehlcke c4f5627f7e Bluetooth: Fix locking in bt_accept_enqueue() for BH context
With commit e163376220 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):

[<ffffff80080d81ec>] __might_sleep+0x4c/0x80
[<ffffff800876c7b0>] lock_sock_nested+0x24/0x58
[<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth]
[<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm]

Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.

Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:

- l2cap_sock_new_connection_cb()
  - uses lock_sock() to lock the parent socket => process context

- rfcomm_connect_ind()
  - acquires the parent socket lock with bh_lock_sock() => BH
    context

- __sco_chan_add()
  - called from sco_chan_add(), which is called from sco_connect().
    parent is NULL, hence bt_accept_enqueue() isn't called in this
    code path and we can ignore it
  - also called from sco_conn_ready(). uses bh_lock_sock() to acquire
    the parent lock => BH context

Fixes: e163376220 ("Bluetooth: Handle bt_accept_enqueue() socket atomically")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2019-01-22 09:51:20 +01:00
Mallikarjun Phulari dd1a8f8a88 Bluetooth: Errata Service Release 8, Erratum 3253
L2CAP: New result values
	0x0006 - Connection refused – Invalid Source CID
	0x0007 - Connection refused – Source CID already allocated

As per the ESR08_V1.0.0, 1.11.2 Erratum 3253, Page No. 54,
"Remote CID invalid Issue".
Applies to Core Specification versions: V5.0, V4.2, v4.1, v4.0, and v3.0 + HS
Vol 3, Part A, Section 4.2, 4.3, 4.14, 4.15.

Core Specification Version 5.0, Page No.1753, Table 4.6 and
Page No. 1767, Table 4.14

New result values are added to l2cap connect/create channel response as
0x0006 - Connection refused – Invalid Source CID
0x0007 - Connection refused – Source CID already allocated

Signed-off-by: Mallikarjun Phulari <mallikarjun.phulari@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-14 10:25:47 +02:00
Mallikarjun Phulari 571f739083 Bluetooth: Use separate L2CAP LE credit based connection result values
Add the result values specific to L2CAP LE credit based connections
and change the old result values wherever they were used.

Signed-off-by: Mallikarjun Phulari <mallikarjun.phulari@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-14 10:24:00 +02:00
Matias Karhumaa 30d65e0804 Bluetooth: Fix debugfs NULL pointer dereference
Fix crash caused by NULL pointer dereference when debugfs functions
le_max_key_read, le_max_key_size_write, le_min_key_size_read or
le_min_key_size_write and Bluetooth adapter was powered off.

Fix is to move max_key_size and min_key_size from smp_dev to hci_dev.
At the same time they were renamed to le_max_key_size and
le_min_key_size.

BUG: unable to handle kernel NULL pointer dereference at 00000000000002e8
PGD 0 P4D 0
Oops: 0000 [#24] SMP PTI
CPU: 2 PID: 6255 Comm: cat Tainted: G      D    OE     4.18.9-200.fc28.x86_64 #1
Hardware name: LENOVO 4286CTO/4286CTO, BIOS 8DET76WW (1.46 ) 06/21/2018
RIP: 0010:le_max_key_size_read+0x45/0xb0 [bluetooth]
Code: 00 00 00 48 83 ec 10 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 48 8b 87 c8 00 00 00 48 8d 7c 24 04 48 8b 80 48 0a 00 00 <48> 8b 80 e8 02 00 00 0f b6 48 52 e8 fb b6 b3 ed be 04 00 00 00 48
RSP: 0018:ffffab23c3ff3df0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 00007f0b4ca2e000 RCX: ffffab23c3ff3f08
RDX: ffffffffc0ddb033 RSI: 0000000000000004 RDI: ffffab23c3ff3df4
RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000
R10: ffffab23c3ff3ed8 R11: 0000000000000000 R12: ffffab23c3ff3f08
R13: 00007f0b4ca2e000 R14: 0000000000020000 R15: ffffab23c3ff3f08
FS:  00007f0b4ca0f540(0000) GS:ffff91bd5e280000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000002e8 CR3: 00000000629fa006 CR4: 00000000000606e0
Call Trace:
 full_proxy_read+0x53/0x80
 __vfs_read+0x36/0x180
 vfs_read+0x8a/0x140
 ksys_read+0x4f/0xb0
 do_syscall_64+0x5b/0x160
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-28 20:53:48 +02:00
Luiz Augusto von Dentz 96cd8eaa13 Bluetooth: L2CAP: Derive rx credits from MTU and MPS
Give enough rx credits for a full packet instead of using an arbitrary
number which may not be enough depending on the MTU and MPS which can
cause interruptions while waiting for more credits, also remove
debugfs entry for l2cap_le_max_credits.

With these changes the credits are restored after each SDU is received
instead of using fixed threshold, this way it is garanteed that there
will always be enough credits to send a packet without waiting more
credits to arrive.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 12:52:08 +02:00
Luiz Augusto von Dentz fe1493101a Bluetooth: L2CAP: Derive MPS from connection MTU
This ensures the MPS can fit in a single HCI fragment so each
segment don't have to be reassembled at HCI level, in addition to
that also remove the debugfs entry to configure the MPS.

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 12:52:08 +02:00
Ankit Navik b950aa8863 Bluetooth: Add definitions and track LE resolve list modification
Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 12:38:52 +02:00
Ankit Navik aa12af77aa Bluetooth: Add definitions for LE set address resolution
Add the definitions for LE address resolution enable HCI commands.
When the LE address resolution enable gets changed via HCI commands
make sure that flag gets updated.

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-10 16:57:57 +02:00
Marcel Holtmann e4cc5a1873 Bluetooth: btqca: Introduce HCI_EV_VENDOR and use it
Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2018-08-06 21:25:05 +03:00
Sean Wang 740011cfe9 Bluetooth: Add new quirk for non-persistent setup settings
Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that
runs setup() after every open() and not just after the first open().

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 14:00:15 +02:00
Jaganath Kanakkassery 85a721a8b0 Bluetooth: Implement secondary advertising on different PHYs
This patch adds support for advertising in primary and secondary
channel on different PHYs. User can add the phy preference in
the flag based on which phy type will be added in extended
advertising parameter would be set.

@ MGMT Command: Add Advertising (0x003e) plen 11
        Instance: 1
        Flags: 0x00000200
          Advertise in CODED on Secondary channel
        Duration: 0
        Timeout: 0
        Advertising data length: 0
        Scan response length: 0
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0000
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE Coded (0x03)
        Secondary max skip: 0x00
        Secondary PHY: LE Coded (0x03)
        SID: 0x00
        Scan request notifications: Disabled (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery acf0aeae43 Bluetooth: Handle ADv set terminated event
This event comes after connection complete event for incoming
connections. Since we now have different random address for
each instance, conn resp address is assigned from this event.

As of now only connection part is handled as we are not
enabling duration or max num of events while starting ext adv.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery a73c046a28 Bluetooth: Implement Set ADV set random address
This basically sets the random address for the adv instance
Random address can be set only if the instance is created which
is done in Set ext adv param.

Random address and rpa expire timer and flags have been added
to adv instance which will be used when the respective
instance is scheduled.

This introduces a hci_get_random_address() which returns the
own address type and random address (rpa or nrpa) based
on the instance flags and hdev flags. New function is required
since own address type should be known before setting adv params
but address can be set only after setting params.

< HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7
        Advertising handle: 0x00
        Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery 45b7749f16 Bluetooth: Implement disable and removal of adv instance
If ext adv is enabled then use ext adv to disable as well.
Also remove the adv set during LE disable.

< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2
        Extended advertising: Disabled (0x00)
        Number of sets: Disable all sets (0x00)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:53 +02:00
Jaganath Kanakkassery a0fb3726ba Bluetooth: Use Set ext adv/scan rsp data if controller supports
This patch implements Set Ext Adv data and Set Ext Scan rsp data
if controller support extended advertising.

Currently the operation is set as Complete data and fragment
preference is set as no fragment

< HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35
        Handle: 0x00
        Operation: Complete extended advertising data (0x03)
        Fragment preference: Minimize fragmentation (0x01)
        Data length: 0x15
        16-bit Service UUIDs (complete): 2 entries
          Heart Rate (0x180d)
          Battery Service (0x180f)
        Name (complete): Test LE
        Company: Google (224)
          Data: 0102
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Data (0x08|0x0037) ncmd 1
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery de181e887a Bluetooth: Impmlement extended adv enable
This patch basically replaces legacy adv with extended adv
based on the controller support. Currently there is no
design change. ie only one adv set will be enabled at a time.

This also adds tx_power in instance and store whatever returns
from Set_ext_parameter, use the same in adv data as well.
For instance 0 tx_power is stored in hdev only.

< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25
        Handle: 0x00
        Properties: 0x0010
          Use legacy advertising PDUs: ADV_NONCONN_IND
        Min advertising interval: 1280.000 msec (0x0800)
        Max advertising interval: 1280.000 msec (0x0800)
        Channel map: 37, 38, 39 (0x07)
        Own address type: Random (0x01)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
        TX power: 127 dbm (0x7f)
        Primary PHY: LE 1M (0x01)
        Secondary max skip: 0x00
        Secondary PHY: LE 1M (0x01)
        SID: 0x00
        Scan request notifications: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 5
      LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1
        Status: Success (0x00)
        TX power (selected): 7 dbm (0x07)
< HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6
        Extended advertising: Enabled (0x01)
        Number of sets: 1 (0x01)
        Entry 0
          Handle: 0x00
          Duration: 0 ms (0x00)
          Max ext adv events: 0
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 6b49bcb4bc Bluetooth: Read no of adv sets during init
This patch reads the number of advertising sets in the controller
during init and save it in hdev.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery b2cc9761f1 Bluetooth: Handle extended ADV PDU types
This patch defines the extended ADV types and handle it in ADV report.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 45bdd86eaf Bluetooth: Set Scan PHYs based on selected PHYs by user
Use the PHYs selected in Set Phy Configuration management command
while scanning.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x05
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
        Entry 1: LE Coded
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery b7c23df85b Bluetooth: Implement PHY changed event
This defines and implement phy changed event and send it to user
whenever selected PHYs changes using SET_PHY_CONFIGURATION.

This will be also trigerred when BREDR pkt_type is changed using
the legacy ioctl HCISETPTYPE.

@ MGMT Command: Set PHY Configuration (0x0045) plen 4
		Selected PHYs: 0x7fff
		  BR 1M 1SLOT
		  BR 1M 3SLOT
		  BR 1M 5SLOT
		  EDR 2M 1SLOT
		  EDR 2M 3SLOT
		  EDR 2M 5SLOT
		  EDR 3M 1SLOT
		  EDR 3M 3SLOT
		  EDR 3M 5SLOT
		  LE 1M TX
		  LE 1M RX
		  LE 2M TX
		  LE 2M RX
		  LE CODED TX
		  LE CODED RX
< HCI Command: LE Set Default PHY (0x08|0x0031) plen 3
		All PHYs preference: 0x00
		TX PHYs preference: 0x07
		  LE 1M
		  LE 2M
		  LE Coded
		RX PHYs preference: 0x07
		  LE 1M
		  LE 2M
		  LE Coded
> HCI Event: Command Complete (0x0e) plen 4
	  LE Set Default PHY (0x08|0x0031) ncmd 1
		Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 3
	  Set PHY Configuration (0x0045) plen 0
		Status: Success (0x00)
@ MGMT Event: PHY Configuration Changed (0x0026) plen 4
		Selected PHYs: 0x7fff
		  BR 1M 1SLOT
		  BR 1M 3SLOT
		  BR 1M 5SLOT
		  EDR 2M 1SLOT
		  EDR 2M 3SLOT
		  EDR 2M 5SLOT
		  EDR 3M 1SLOT
		  EDR 3M 3SLOT
		  EDR 3M 5SLOT
		  LE 1M TX
		  LE 1M RX
		  LE 2M TX
		  LE 2M RX
		  LE CODED TX
		  LE CODED RX

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 0314f2867f Bluetooth: Implement Set PHY Confguration command
This enables user to set phys which will be used in all subsequent
connections. Also host will use the same in LE scanning as well.

@ MGMT Command: Set PHY Configuration (0x0045) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
< HCI Command: LE Set Default PHY (0x08|0x0031) plen 3
        All PHYs preference: 0x00
        TX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
        RX PHYs preference: 0x07
          LE 1M
          LE 2M
          LE Coded
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Default PHY (0x08|0x0031) ncmd 1
        Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 3
      Set PHY Configuration (0x0045) plen 0
        Status: Success (0x00)
@ MGMT Event: PHY Configuration Changed (0x0026) plen 4
        Selected PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 6244691fec Bluetooth: Implement Get PHY Configuration mgmt command
This commands basically retrieve the supported packet types of
BREDR and supported PHYs of the controller.

BR_1M_1SLOT, LE_1M_TX and LE_1M_RX would be supported by default.
Other PHYs are supported based on the local features.

Also this sets PHY_CONFIGURATION bit in supported settings.

@ MGMT Command: Get PHY Configuration (0x0044) plen 0
@ MGMT Event: Command Complete (0x0001) plen 15
      Get PHY Configuration (0x0044) plen 12
        Status: Success (0x00)
        Supported PHYs: 0x7fff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
        Configurable PHYs: 0x79fe
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 2M TX
          LE 2M RX
          LE CODED TX
          LE CODED RX
        Selected PHYs: 0x07ff
          BR 1M 1SLOT
          BR 1M 3SLOT
          BR 1M 5SLOT
          EDR 2M 1SLOT
          EDR 2M 3SLOT
          EDR 2M 5SLOT
          EDR 3M 1SLOT
          EDR 3M 3SLOT
          EDR 3M 5SLOT
          LE 1M TX
          LE 1M RX

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 5075b972f2 Bluetooth: Add defines for BREDR pkt_type and LE PHYs
This also add macros for checking LMP support for different
pkt_types

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 6decb5b45e Bluetooth: Define PHY flags in hdev and set 1M as default
1M is mandatory to be supported by LE controllers and the same
would be set in power on. This patch defines hdev flags for
LE PHYs and set 1M to default.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30 13:44:52 +02:00
Jaganath Kanakkassery 4d94f95d30 Bluetooth: Use extended LE Connection if supported
This implements extended LE craete connection and enhanced
LE conn complete event if the controller supports.

For now it is as good as legacy LE connection and event as
no new features in the extended connection is handled.

< HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26
        Filter policy: White list is not used (0x00)
        Own address type: Public (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Initiating PHYs: 0x01
        Entry 0: LE 1M
          Scan interval: 60.000 msec (0x0060)
          Scan window: 60.000 msec (0x0060)
          Min connection interval: 50.00 msec (0x0028)
          Max connection interval: 70.00 msec (0x0038)
          Connection latency: 0 (0x0000)
          Supervision timeout: 420 msec (0x002a)
          Min connection length: 0.000 msec (0x0000)
          Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4
      LE Extended Create Connection (0x08|0x0043) ncmd 2
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 31
      LE Enhanced Connection Complete (0x0a)
        Status: Success (0x00)
        Handle: 3585
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: DB:7E:2E:1D:85:E8 (Static)
        Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable)
        Connection interval: 67.50 msec (0x0036)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x00
@ MGMT Event: Device Connected (0x000b) plen 40
        LE Address: DB:7E:2E:1D:85:E8 (Static)
        Flags: 0x00000000
        Data length: 27
        Name (complete): Designer Mouse
        Appearance: Mouse (0x03c2)
        Flags: 0x05
          LE Limited Discoverable Mode
          BR/EDR Not Supported
        16-bit Service UUIDs (complete): 1 entry
          Human Interface Device (0x1812)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:54:03 +02:00
Jaganath Kanakkassery c215e9397b Bluetooth: Process extended ADV report event
This patch enables Extended ADV report event if extended scanning
is supported in the controller and process the same.

The new features are not handled and for now its as good as
legacy ADV report.

> HCI Event: LE Meta Event (0x3e) plen 53
      LE Extended Advertising Report (0x0d)
        Num reports: 1
        Entry 0
          Event type: 0x0013
            Props: 0x0013
              Connectable
              Scannable
              Use legacy advertising PDUs
            Data status: Complete
          Legacy PDU Type: ADV_IND (0x0013)
          Address type: Random (0x01)
          Address: DB:7E:2E:1A:85:E8 (Static)
          Primary PHY: LE 1M
          Secondary PHY: LE 1M
          SID: 0x00
          TX power: 0 dBm
          RSSI: -90 dBm (0xa6)
          Periodic advertising invteral: 0.00 msec (0x0000)
          Direct address type: Public (0x00)
          Direct address: 00:00:00:00:00:00 (OUI 00-00-00)
          Data length: 0x1b
        0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65  ..Designer Mouse
        03 19 c2 03 02 01 05 03 03 12 18                 ...........

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:43:34 +02:00
Jaganath Kanakkassery a2344b9e3a Bluetooth: Use extended scanning if controller supports
This implements Set extended scan param and set extended scan enable
commands and use it for start LE scan based on controller support.

The new features added in these commands are setting of new PHY for
scanning and setting of scan duration. Both features are disabled
for now, meaning only 1M PHY is set and scan duration is set to 0
which means that scanning will be done untill scan disable is called.

< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement (0x00)
        PHYs: 0x01
        Entry 0: LE 1M
          Type: Active (0x01)
          Interval: 11.250 msec (0x0012)
          Window: 11.250 msec (0x0012)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
        Extended scan: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
        Duration: 0 msec (0x0000)
        Period: 0.00 sec (0x0000)
> HCI Event: Command Complete (0x0e) plen 4
      LE Set Extended Scan Enable (0x08|0x0042) ncmd 2
        Status: Success (0x00)

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 22:41:17 +02:00
Ankit Navik 545f2596b9 Bluetooth: Add HCI command for clear Resolv list
Check for Resolv list supported by controller. So check the supported
commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 28.919131
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 28.920016
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 28.920164
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 28.920873
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 28.921109
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 28.922016
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0  #61 [hci0] 28.922166
> HCI Event: Command Complete (0x0e) plen 4                #62 [hci0] 28.922872
      LE Clear Resolving List (0x08|0x0029) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #63 [hci0] 28.923117
> HCI Event: Command Complete (0x0e) plen 12               #64 [hci0] 28.924030
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 12:40:08 +02:00
Ankit Navik cfdb0c2d09 Bluetooth: Store Resolv list size
When the controller supports the Read LE Resolv List size feature, the
maximum list size are read and now stored.

Before patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 17.979791
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 17.980629
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 17.980786
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 17.981627
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #59 [hci0] 17.981786
> HCI Event: Command Complete (0x0e) plen 12               #60 [hci0] 17.982636
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

After patch:
< HCI Command: LE Read White List... (0x08|0x000f) plen 0  #55 [hci0] 13.338168
> HCI Event: Command Complete (0x0e) plen 5                #56 [hci0] 13.338842
      LE Read White List Size (0x08|0x000f) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Clear White List (0x08|0x0010) plen 0    #57 [hci0] 13.339029
> HCI Event: Command Complete (0x0e) plen 4                #58 [hci0] 13.339939
      LE Clear White List (0x08|0x0010) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0  #59 [hci0] 13.340152
> HCI Event: Command Complete (0x0e) plen 5                #60 [hci0] 13.340952
      LE Read Resolving List Size (0x08|0x002a) ncmd 1
        Status: Success (0x00)
        Size: 25
< HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0  #61 [hci0] 13.341180
> HCI Event: Command Complete (0x0e) plen 12               #62 [hci0] 13.341898
      LE Read Maximum Data Length (0x08|0x002f) ncmd 1
        Status: Success (0x00)
        Max TX octets: 251
        Max TX time: 17040
        Max RX octets: 251
        Max RX time: 17040

Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06 12:40:08 +02:00
Linus Torvalds a11e1d432b Revert changes to convert to ->poll_mask() and aio IOCB_CMD_POLL
The poll() changes were not well thought out, and completely
unexplained.  They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.

Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead.  That gets rid of one of the new indirections.

But that doesn't fix the new complexity that is completely unwarranted
for the regular case.  The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.

[ This revert is a revert of about 30 different commits, not reverted
  individually because that would just be unnecessarily messy  - Linus ]

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-28 10:40:47 -07:00
Linus Torvalds 1c8c5a9d38 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Add Maglev hashing scheduler to IPVS, from Inju Song.

 2) Lots of new TC subsystem tests from Roman Mashak.

 3) Add TCP zero copy receive and fix delayed acks and autotuning with
    SO_RCVLOWAT, from Eric Dumazet.

 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
    Brouer.

 5) Add ttl inherit support to vxlan, from Hangbin Liu.

 6) Properly separate ipv6 routes into their logically independant
    components. fib6_info for the routing table, and fib6_nh for sets of
    nexthops, which thus can be shared. From David Ahern.

 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
    messages from XDP programs. From Nikita V. Shirokov.

 8) Lots of long overdue cleanups to the r8169 driver, from Heiner
    Kallweit.

 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.

10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.

11) Plumb extack down into fib_rules, from Roopa Prabhu.

12) Add Flower classifier offload support to igb, from Vinicius Costa
    Gomes.

13) Add UDP GSO support, from Willem de Bruijn.

14) Add documentation for eBPF helpers, from Quentin Monnet.

15) Add TLS tx offload to mlx5, from Ilya Lesokhin.

16) Allow applications to be given the number of bytes available to read
    on a socket via a control message returned from recvmsg(), from
    Soheil Hassas Yeganeh.

17) Add x86_32 eBPF JIT compiler, from Wang YanQing.

18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
    From Björn Töpel.

19) Remove indirect load support from all of the BPF JITs and handle
    these operations in the verifier by translating them into native BPF
    instead. From Daniel Borkmann.

20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.

21) Allow XDP programs to do lookups in the main kernel routing tables
    for forwarding. From David Ahern.

22) Allow drivers to store hardware state into an ELF section of kernel
    dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.

23) Various RACK and loss detection improvements in TCP, from Yuchung
    Cheng.

24) Add TCP SACK compression, from Eric Dumazet.

25) Add User Mode Helper support and basic bpfilter infrastructure, from
    Alexei Starovoitov.

26) Support ports and protocol values in RTM_GETROUTE, from Roopa
    Prabhu.

27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
    Brouer.

28) Add lots of forwarding selftests, from Petr Machata.

29) Add generic network device failover driver, from Sridhar Samudrala.

* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
  strparser: Add __strp_unpause and use it in ktls.
  rxrpc: Fix terminal retransmission connection ID to include the channel
  net: hns3: Optimize PF CMDQ interrupt switching process
  net: hns3: Fix for VF mailbox receiving unknown message
  net: hns3: Fix for VF mailbox cannot receiving PF response
  bnx2x: use the right constant
  Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
  net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
  enic: fix UDP rss bits
  netdev-FAQ: clarify DaveM's position for stable backports
  rtnetlink: validate attributes in do_setlink()
  mlxsw: Add extack messages for port_{un, }split failures
  netdevsim: Add extack error message for devlink reload
  devlink: Add extack to reload and port_{un, }split operations
  net: metrics: add proper netlink validation
  ipmr: fix error path when ipmr_new_table fails
  ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
  net: hns3: remove unused hclgevf_cfg_func_mta_filter
  netfilter: provide udp*_lib_lookup for nf_tproxy
  qed*: Utilize FW 8.37.2.0
  ...
2018-06-06 18:39:49 -07:00
Christoph Hellwig 17112d8081 net/bluetooth: convert to ->poll_mask
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-26 09:16:44 +02:00
Loic Poulain d6ee6ad774 Bluetooth: Add __hci_cmd_send function
This function allows to send a HCI command without expecting any
controller event/response in return. This is allowed for vendor-
specific commands only.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18 06:37:52 +02:00
David S. Miller 4c7c12e0c9 Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:

====================
pull request: bluetooth 2018-04-08

Here's one important Bluetooth fix for the 4.17-rc series that's needed
to pass several Bluetooth qualification test cases.

Let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-08 17:19:15 -04:00
Szymon Janc 082f2300cf Bluetooth: Fix connection if directed advertising and privacy is used
Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.

This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C

Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6          #11350 [hci0] 84680.231216
        Address: 56:BC:E8:24:11:68 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4                        #11351 [hci0] 84680.246022
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7         #11352 [hci0] 84680.246417
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                        #11353 [hci0] 84680.248854
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11354 [hci0] 84680.249466
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                        #11355 [hci0] 84680.253222
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                          #11356 [hci0] 84680.458387
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
          Identity type: Random (0x01)
          Identity: F2:F1:06:3D:9C:42 (Static)
        RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2             #11357 [hci0] 84680.458737
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                        #11358 [hci0] 84680.469982
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25          #11359 [hci0] 84680.470444
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 53:38:DA:46:8C:45 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                          #11360 [hci0] 84680.474971
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0    #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4                        #11362 [hci0] 84682.551014
      LE Create Connection Cancel (0x08|0x000e) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                          #11363 [hci0] 84682.551074
      LE Connection Complete (0x01)
        Status: Unknown Connection Identifier (0x02)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Public (0x00)
        Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
        Connection interval: 0.00 msec (0x0000)
        Connection latency: 0 (0x0000)
        Supervision timeout: 0 msec (0x0000)
        Master clock accuracy: 0x00

After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7    #210 [hci0] 667.152459
        Type: Passive (0x00)
        Interval: 60.000 msec (0x0060)
        Window: 30.000 msec (0x0030)
        Own address type: Random (0x01)
        Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4                   #211 [hci0] 667.153613
      LE Set Scan Parameters (0x08|0x000b) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2        #212 [hci0] 667.153704
        Scanning: Enabled (0x01)
        Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4                   #213 [hci0] 667.154584
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18                     #214 [hci0] 667.182619
      LE Direct Advertising Report (0x0b)
        Num reports: 1
        Event type: Connectable directed - ADV_DIRECT_IND (0x01)
        Address type: Random (0x01)
        Address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Direct address type: Random (0x01)
        Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
        RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2       #215 [hci0] 667.182704
        Scanning: Disabled (0x00)
        Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4                  #216 [hci0] 667.183599
      LE Set Scan Enable (0x08|0x000c) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6    #217 [hci0] 667.183645
        Address: 7C:C1:57:A5:B7:A8 (Resolvable)
          Identity type: Random (0x01)
          Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4                  #218 [hci0] 667.184590
      LE Set Random Address (0x08|0x0005) ncmd 1
        Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25    #219 [hci0] 667.184613
        Scan interval: 60.000 msec (0x0060)
        Scan window: 60.000 msec (0x0060)
        Filter policy: White list is not used (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Own address type: Random (0x01)
        Min connection interval: 30.00 msec (0x0018)
        Max connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Min connection length: 0.000 msec (0x0000)
        Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4                    #220 [hci0] 667.186558
      LE Create Connection (0x08|0x000d) ncmd 1
        Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19                    #221 [hci0] 667.485824
      LE Connection Complete (0x01)
        Status: Success (0x00)
        Handle: 0
        Role: Master (0x00)
        Peer address type: Random (0x01)
        Peer address: 50:52:D9:A6:48:A0 (Resolvable)
          Identity type: Public (0x00)
          Identity: 11:22:33:44:55:66 (OUI 11-22-33)
        Connection interval: 50.00 msec (0x0028)
        Connection latency: 0 (0x0000)
        Supervision timeout: 420 msec (0x002a)
        Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13          {0x0002} [hci0] 667.485996
        LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
        Flags: 0x00000000
        Data length: 0

Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
2018-04-03 16:12:56 +02:00
Jaganath Kanakkassery 8c59c264e5 Bluetooth: Fix data type of appearence
It should be __le16 instead of __u16 since its part of
mgmt API.

Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-01 14:25:30 +02:00
Al Viro ade994f4f6 net: annotate ->poll() instances
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-11-27 16:20:04 -05:00
Marcel Holtmann 2064ee332e Bluetooth: Use bt_dev_err and bt_dev_info when possible
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-30 12:25:45 +02:00
Konrad Zapałowicz 1f01d8be0e Bluetooth: increase timeout for le auto connections
This patch increases the connection timeout for LE connections that are
triggered by the advertising report to 4 seconds.

It has been observed that devices equipped with wifi+bt combo SoC fail
to create a connection with BLE devices due to their coexistence issues.
Increasing this timeout gives them enough time to complete the
connection with success.

Signed-off-by: Konrad Zapałowicz <konrad.zapalowicz@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-29 14:10:35 +01:00
Loic Poulain 65bce46298 Bluetooth: make baswap src const
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-09-01 22:49:47 +02:00
Marcel Holtmann de2ba3039c Bluetooth: Set LE Default PHY preferences
If the LE Set Default PHY command is supported, the indicate to the
controller that the host has no preferences for transmitter PHY or
receiver PHY selection.

Issuing this command gives the controller a clear indication that other
PHY can be selected if available.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-05-18 13:52:49 +02:00
Marcel Holtmann 9756d33b85 Bluetooth: Enable LE Channel Selection Algorithm event
If the Channel Selection Algorithm #2 feature is supported, then enable
the new LE Channel Selection Algorithm event.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-05-18 13:52:49 +02:00
Marcin Kraglak d8edd9ed15 Bluetooth: L2CAP: Fix L2CAP_CR_SCID_IN_USE value
Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C.

Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-04-12 22:02:37 +02:00