Commit Graph

16 Commits

Author SHA1 Message Date
Arnd Bergmann b115bebc07 gpio: xgene: mark PM functions as __maybe_unused
When CONFIG_PM_SLEEP is disabled, we get a warning about unused functions:

drivers/gpio/gpio-xgene.c:155:12: warning: 'xgene_gpio_resume' defined but not used [-Wunused-function]
 static int xgene_gpio_resume(struct device *dev)
            ^~~~~~~~~~~~~~~~~
drivers/gpio/gpio-xgene.c:142:12: warning: 'xgene_gpio_suspend' defined but not used [-Wunused-function]
 static int xgene_gpio_suspend(struct device *dev)

The warnings are harmless and can be avoided by simplifying the code and marking
the functions as __maybe_unused.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-06 14:35:22 +01:00
Linus Torvalds 1eccc6e152 This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
 
 - Support for natively single-ended GPIO driver stages. This
   means that if the hardware has registers to configure open
   drain or open source configuration, we use that rather than
   (as we did before) try to emulate it by switching the line
   to an input to get high impedance. This is also documented
   throughly in Documentation/gpio/driver.txt for those of you
   who did not understand one word of what I just wrote.
 
 - Start to do away with the unnecessarily complex and
   unitelligible ARCH_REQUIRE_GPIOLIB and
   ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
   the time when the GPIO subsystem was unmaintained. Archs can
   now just select GPIOLIB and be done with it, cleanups to
   arches will trickle in for the next kernel. Some minor archs
   ACKed the changes immediately so these are included in this
   pull request.
 
 - Advancing the use of the data pointer inside the GPIO device
   for storing driver data by switching the PowerPC, Super-H
   Unicore and a few other subarches or subsystem drivers in
   ALSA SoC, Input, serial, SSB, staging etc to use it.
 
 - The initialization now reads the input/output state of the
   GPIO lines, so that each GPIO descriptor knows - if this
   callback is implemented - whether the line is input or
   output. This also reflects nicely in userspace "lsgpio".
 
 - It is now possible to name GPIO producer names, line names,
   from the device tree. (Platform data has been supported for
   a while.) I bet we will get a similar mechanism for ACPI
   one of those days. This makes is possible to get sensible
   producer names for e.g. GPIO rails in "lsgpio" in userspace.
 
 New drivers:
 
 - New driver for the Loongson1.
 
 - The XLP driver now supports Broadcom Vulcan ARM64.
 
 - The IT87 driver now supports IT8620 and IT8628.
 
 - The PCA953X driver now supports Galileo Gen2.
 
 Driver improvements:
 
 - MCP23S08 was switched to use the gpiolib irqchip helpers and
   now also suppors level-triggered interrupts.
 
 - 74x164 and RCAR now supports the .set_multiple() callback
 
 - AMDPT was converted to use generic GPIO.
 
 - TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
   support the new single ended callback for open drain
   and in some cases open source.
 
 - Implement the .get_direction() callback for a few more drivers
   like PL061, Xgene.
 
 Cleanups:
 
 - Paul Gortmaker combed through the drivers and de-modularized
   those who are not really modules.
 
 - Move the GPIO poweroff DT bindings to the power subdir where
   they belong.
 
 - Rename gpio-generic.c to gpio-mmio.c, which is much more to the
   point. That's what it is handling, nothing more, nothing less.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJXOuJ5AAoJEEEQszewGV1zNXsQAII5wtkP69WRJ3goYBKg1dZN
 DkuLqZyVI4hCgRhptzUW10gDLHKKOCVubfetTJHSpyG/dWDJXPCyH6FHF+pW6lMX
 y+em8kAvWctKpaosy4EM7O55/IohW0/fNCTOfzfrUNivjydFuA2XwPUiPqC7111O
 DeKlC/t+W1JEvZTiKMi83pKq+9wqhiHmD0qxRHhV57S+MT8e7mdlSKOp7uUkKPkg
 LPlerXosnmeFjL2emuSnKl/tq8pOyruU6uaIGG/uwpbo2W86Dok9GY2GWkQ4pANT
 pDtprc4aJ/Clf6Q0CoKwQbmAozqTDeJo+Und9tRs2KuZRly2bWOcyVE0lyK+Y4s0
 544LcKw2q6cB9ARZ6JExEVRJejPISGKMqo9TaHkyNSIJoiiatKYvNS4WVeFtTgbI
 W+1WfM1svPymNRqVPO1PMLV+3m9dalDH2WjtaFF21uCAQ/G0AuPEHjEDbbx0HIpb
 qrvWmYzZ97Rm/LdYROFRO53nEdCp2jh6c3n4/2kGYM8H0suvGxXZsB1g4i+Dm+B+
 qKVTS282azlDuH9ohXeXizeb6atK6s8TC3Rmew97SmXDO00cUQzEQO/ZquRLHY9r
 n83afQ4OL2Z9yruAxAk7pCshVSyheOsHuFPuZ7bwPW31VMdoWNRkhnaTUXMjGfYg
 3y39IHrCKWNMCCVM1iNl
 =z4d6
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for kernel cycle v4.7:

  Core infrastructural changes:

   - Support for natively single-ended GPIO driver stages.

     This means that if the hardware has registers to configure open
     drain or open source configuration, we use that rather than (as we
     did before) try to emulate it by switching the line to an input to
     get high impedance.

     This is also documented throughly in Documentation/gpio/driver.txt
     for those of you who did not understand one word of what I just
     wrote.

   - Start to do away with the unnecessarily complex and unitelligible
     ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
     evolutional artifact from the time when the GPIO subsystem was
     unmaintained.

     Archs can now just select GPIOLIB and be done with it, cleanups to
     arches will trickle in for the next kernel.  Some minor archs ACKed
     the changes immediately so these are included in this pull request.

   - Advancing the use of the data pointer inside the GPIO device for
     storing driver data by switching the PowerPC, Super-H Unicore and
     a few other subarches or subsystem drivers in ALSA SoC, Input,
     serial, SSB, staging etc to use it.

   - The initialization now reads the input/output state of the GPIO
     lines, so that each GPIO descriptor knows - if this callback is
     implemented - whether the line is input or output.  This also
     reflects nicely in userspace "lsgpio".

   - It is now possible to name GPIO producer names, line names, from
     the device tree.  (Platform data has been supported for a while).
     I bet we will get a similar mechanism for ACPI one of those days.
     This makes is possible to get sensible producer names for e.g.
     GPIO rails in "lsgpio" in userspace.

  New drivers:

   - New driver for the Loongson1.

   - The XLP driver now supports Broadcom Vulcan ARM64.

   - The IT87 driver now supports IT8620 and IT8628.

   - The PCA953X driver now supports Galileo Gen2.

  Driver improvements:

   - MCP23S08 was switched to use the gpiolib irqchip helpers and now
     also suppors level-triggered interrupts.

   - 74x164 and RCAR now supports the .set_multiple() callback

   - AMDPT was converted to use generic GPIO.

   - TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
     support the new single ended callback for open drain and in some
     cases open source.

   - Implement the .get_direction() callback for a few more drivers like
     PL061, Xgene.

  Cleanups:

   - Paul Gortmaker combed through the drivers and de-modularized those
     who are not really modules.

   - Move the GPIO poweroff DT bindings to the power subdir where they
     belong.

   - Rename gpio-generic.c to gpio-mmio.c, which is much more to the
     point.  That's what it is handling, nothing more, nothing less"

* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
  MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
  gpio: zevio: make it explicitly non-modular
  gpio: timberdale: make it explicitly non-modular
  gpio: stmpe: make it explicitly non-modular
  gpio: sodaville: make it explicitly non-modular
  pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
  gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
  gpio: dt-bindings: add wd,mbl-gpio bindings
  gpio: of: make it possible to name GPIO lines
  gpio: make gpiod_to_irq() return negative for NO_IRQ
  gpio: xgene: implement .get_direction()
  gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
  gpio: tegra: Implement gpio_get_direction callback
  gpio: set up initial state from .get_direction()
  gpio: rename gpio-generic.c into gpio-mmio.c
  gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
  gpio: dwapb: add gpio-signaled acpi event support
  gpio: dwapb: convert device node to fwnode
  gpio: dwapb: remove name from dwapb_port_property
  gpio/qoriq: select IRQ_DOMAIN
  ...
2016-05-17 17:39:42 -07:00
Linus Walleij 3b711e0781 gpio: xgene: implement .get_direction()
This implements the .get_direction() callback for the xgene GPIO
controller.

Cc: Duc Dang <dhdang@apm.com>
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-01 10:31:30 +02:00
Duc Dang 0c60de3f73 gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
This patch enables ACPI support for X-Gene GFC GPIO driver.

Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-01 10:23:12 +02:00
Paul Gortmaker b33d12d3d7 gpio: xgene: make explicitly non-modular
The Kconfig currently controlling compilation of this code is:

drivers/gpio/Kconfig:config GPIO_XGENE
drivers/gpio/Kconfig:   bool "APM X-Gene GPIO controller support"

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.

Cc: Feng Kan <fkan@apm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-31 15:09:16 +02:00
Axel Lin 8d8ee18cc7 gpio: xgene: Prevent NULL pointer dereference
platform_get_resource() can return NULL, thus add NULL test to prevent NULL
pointer dereference.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-03-30 10:39:39 +02:00
Laxman Dewangan 9d113c696f gpio: xgene: Use devm_gpiochip_add_data() for gpio registration
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
2016-02-23 20:35:54 +05:30
Linus Walleij ac9dc85eea gpio: xgene: use gpiochip data pointer
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().

Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-01-05 11:21:19 +01:00
Linus Walleij 58383c7842 gpio: change member .dev to .parent
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-19 09:24:35 +01:00
Wolfram Sang 4a3a950ee9 gpio: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:20:31 +02:00
Axel Lin 513d3c0f40 gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
This driver depends on OF_GPIO, so it won't be built if !CONFIG_OF.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-24 11:03:01 +02:00
Axel Lin 02ed185af0 gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-24 11:01:44 +02:00
Axel Lin 1a19864e3b gpio: xgene: Fix missing spin_lock_init()
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-24 11:00:54 +02:00
Wei Yongjun 4f51b91335 gpio: Fix return value check in xgene_gpio_probe()
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-24 10:04:28 +02:00
Linus Walleij da26d5d803 gpio: remove remaining users of gpiochip_remove() retval
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.

Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-09-23 17:51:17 +02:00
Feng Kan 29cbf4589f gpio: Add APM X-Gene SoC GPIO controller support
Add APM X-Gene SoC gpio controller driver.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-08-28 14:19:47 +02:00