Commit Graph

9041 Commits

Author SHA1 Message Date
Stephen M. Cameron 256d0eaac8 [SCSI] hpsa: fix handling of protocol error
If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor.  CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected.  This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not.  Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug.  This bug should not normally cause a problem for direct
attached disk storage.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-18 12:29:30 +01:00
sreekanth.reddy@lsi.com 10cce6d8b5 [SCSI] mpt2sas: Fix for issue - Unable to boot from the drive connected to HBA
This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.

[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-17 13:49:47 +01:00
Eddie Wai d653220711 [SCSI] bnx2i: Fixed NULL ptr deference for 1G bnx2 Linux iSCSI offload
This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.

One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets.  When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.

This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.

This change only affects Broadcom's 5709 chipset.

Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
 [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G     ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>]  [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50  EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS:  0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack:  000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
 ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
 0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
 <IRQ>  [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
 [<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
 [<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
 [<ffffffff800125a0>] __do_softirq+0x89/0x133
 [<ffffffff8005e30c>] call_softirq+0x1c/0x28
 [<ffffffff8006d5de>] do_softirq+0x2c/0x7d
 [<ffffffff8006d46e>] do_IRQ+0xee/0xf7
 [<ffffffff8005d625>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
 [<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
 [<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
 [<ffffffff80049560>] cpu_idle+0x95/0xb8
 [<ffffffff80078b1c>] start_secondary+0x479/0x488

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-17 13:40:32 +01:00
Wang Sen 27e99ade81 [SCSI] scsi: virtio-scsi: Fix address translation failure of HighMem pages used by sg list
When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.

        # sudo mkfs.ext4 /dev/sdb  (/dev/sdb is the virtio-scsi LUN.)
        # sudo mount /dev/sdb /mnt
        # dd if=/dev/zero of=/mnt/file bs=1M count=1024

In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.

Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html

Finally, value assignment approach was adopted because:

Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list.  Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.

I have tested the patch on my workstation. QEMU would not crash any more.

Cc: <stable@vger.kernel.org> # 3.4: 4fe74b1: [SCSI] virtio-scsi: SCSI driver
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-09-14 15:47:01 +01:00
James Bottomley 14216561e1 [SCSI] Fix 'Device not ready' issue on mpt2sas
This is a particularly nasty SCSI ATA Translation Layer (SATL) problem.

SAT-2 says (section 8.12.2)

        if the device is in the stopped state as the result of
        processing a START STOP UNIT command (see 9.11), then the SATL
        shall terminate the TEST UNIT READY command with CHECK CONDITION
        status with the sense key set to NOT READY and the additional
        sense code of LOGICAL UNIT NOT READY, INITIALIZING COMMAND
        REQUIRED;

mpt2sas internal SATL seems to implement this.  The result is very confusing
standby behaviour (using hdparm -y).  If you suspend a drive and then send
another command, usually it wakes up.  However, if the next command is a TEST
UNIT READY, the SATL sees that the drive is suspended and proceeds to follow
the SATL rules for this, returning NOT READY to all subsequent commands.  This
means that the ordering of TEST UNIT READY is crucial: if you send TUR and
then a command, you get a NOT READY to both back.  If you send a command and
then a TUR, you get GOOD status because the preceeding command woke the drive.

This bit us badly because

commit 85ef06d1d2
Author: Tejun Heo <tj@kernel.org>
Date:   Fri Jul 1 16:17:47 2011 +0200

    block: flush MEDIA_CHANGE from drivers on close(2)

Changed our ordering on TEST UNIT READY commands meaning that SATA drives
connected to an mpt2sas now suspend and refuse to wake (because the mpt2sas
SATL sees the suspend *before* the drives get awoken by the next ATA command)
resulting in lots of failed commands.

The standard is completely nuts forcing this inconsistent behaviour, but we
have to work around it.

The fix for this is twofold:

   1. Set the allow_restart flag so we wake the drive when we see it has been
      suspended

   2. Return all TEST UNIT READY status directly to the mid layer without any
      further error handling which prevents us causing error handling which
      may offline the device just because of a media check TUR.

Reported-by: Matthias Prager <linux@matthiasprager.de>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-22 09:42:54 +04:00
Mike Snitzer 27c419739b [SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
The following v3.4-rc1 commit unmasked an existing bug in scsi_io_completion's
SG_IO error handling: 47ac56d [SCSI] scsi_error: classify some ILLEGAL_REQUEST
sense as a permanent TARGET_ERROR

Given that certain ILLEGAL_REQUEST are now properly categorized as
TARGET_ERROR the host_byte is being set (before host_byte wasn't ever
set for these ILLEGAL_REQUEST).

In scsi_io_completion, initialize req->errors with cmd->result _after_
the SG_IO block that calls __scsi_error_from_host_byte (which may
modify the host_byte).

Before this fix:

    cdb to send: 12 01 01 00 00 00
ioctl(3, SG_IO, {'S', SG_DXFER_NONE, cmd[6]=[12, 01, 01, 00, 00, 00],
    mx_sb_len=32, iovec_count=0, dxfer_len=0, timeout=20000, flags=0,
    status=02, masked_status=01, sb[19]=[70, 00, 05, 00, 00, 00, 00, 0b,
    00, 00, 00, 00, 24, 00, 00, 00, 00, 00, 00], host_status=0x10,
    driver_status=0x8, resid=0, duration=0, info=0x1}) = 0
SCSI Status: Check Condition

Sense Information:
sense buffer empty

After:

    cdb to send: 12 01 01 00 00 00
ioctl(3, SG_IO, {'S', SG_DXFER_NONE, cmd[6]=[12, 01, 01, 00, 00, 00],
    mx_sb_len=32, iovec_count=0, dxfer_len=0, timeout=20000, flags=0,
    status=02, masked_status=01, sb[19]=[70, 00, 05, 00, 00, 00, 00, 0b,
    00, 00, 00, 00, 24, 00, 00, 00, 00, 00, 00], host_status=0,
    driver_status=0x8, resid=0, duration=0, info=0x1}) = 0
SCSI Status: Check Condition

Sense Information:
 Fixed format, current;  Sense key: Illegal Request
 Additional sense: Invalid field in cdb
 Raw sense data (in hex):
        70 00 05 00 00 00 00 0b  00 00 00 00 24 00 00 00
        00 00 00

Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Babu Moger <babu.moger@netapp.com>
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-22 09:42:31 +04:00
Kashyap Desai bd8d6dd43a [SCSI] megaraid_sas: Move poll_aen_lock initializer
The following patch moves the poll_aen_lock initializer from
megasas_probe_one() to megasas_init().  This prevents a crash when a user
loads the driver and tries to issue a poll() system call on the ioctl
interface with no adapters present.

Signed-off-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: Adam Radford <aradford@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-22 09:39:25 +04:00
sreekanth.reddy@lsi.com 338b131a32 [SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value
If the specified max_queue_depth setting is less than the
expected number of internal commands, then driver will calculate
the queue depth size to a negitive number. This negitive number
is actually a very large number because variable is unsigned
16bit integer. So, the driver will ask for a very large amount of
memory for message frames and resulting into oops as memory
allocation routines will not able to handle such a large request.

So, in order to limit this kind of oops, The driver need to set
the max_queue_depth to a scsi mid layer's can_queue value. Then
the overall message frames required for IO is minimum of either
(max_queue_depth plus internal commands) or the IOC global
credits.

Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-08-22 09:38:49 +04:00
Linus Torvalds 8cf1a3fce0 Merge branch 'for-3.6/core' of git://git.kernel.dk/linux-block
Pull core block IO bits from Jens Axboe:
 "The most complicated part if this is the request allocation rework by
  Tejun, which has been queued up for a long time and has been in
  for-next ditto as well.

  There are a few commits from yesterday and today, mostly trivial and
  obvious fixes.  So I'm pretty confident that it is sound.  It's also
  smaller than usual."

* 'for-3.6/core' of git://git.kernel.dk/linux-block:
  block: remove dead func declaration
  block: add partition resize function to blkpg ioctl
  block: uninitialized ioc->nr_tasks triggers WARN_ON
  block: do not artificially constrain max_sectors for stacking drivers
  blkcg: implement per-blkg request allocation
  block: prepare for multiple request_lists
  block: add q->nr_rqs[] and move q->rq.elvpriv to q->nr_rqs_elvpriv
  blkcg: inline bio_blkcg() and friends
  block: allocate io_context upfront
  block: refactor get_request[_wait]()
  block: drop custom queue draining used by scsi_transport_{iscsi|fc}
  mempool: add @gfp_mask to mempool_create_node()
  blkcg: make root blkcg allocation use %GFP_KERNEL
  blkcg: __blkg_lookup_create() doesn't need radix preload
2012-08-01 09:02:41 -07:00
Jeff Garzik 8407884dd9 Merge branch 'master' [vanilla Linus master] into libata-dev.git/upstream
Two bits were appended to the end of the bitfield
list in struct scsi_device.  Resolve that conflict
by including both bits.

Conflicts:
	include/scsi/scsi_device.h
2012-07-25 15:58:48 -04:00
Linus Torvalds bdc0077af5 SCSI misc on 20120724
The most important feature of this patch set is the new async infrastructure
 that makes sure async_synchronize_full() synchronizes all domains and allows
 us to remove all the hacks (like having scsi_complete_async_scans() in the
 device base code) and means that the async infrastructure will "just work" in
 future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
 megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
 sas and FC.
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
 0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
 /uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
 VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
 NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
 G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
 =y2sh
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull first round of SCSI updates from James Bottomley:
 "The most important feature of this patch set is the new async
  infrastructure that makes sure async_synchronize_full() synchronizes
  all domains and allows us to remove all the hacks (like having
  scsi_complete_async_scans() in the device base code) and means that
  the async infrastructure will "just work" in future.

  The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
  megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
  work in sas and FC.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
  [SCSI] Revert "[SCSI] fix async probe regression"
  [SCSI] cleanup usages of scsi_complete_async_scans
  [SCSI] queue async scan work to an async_schedule domain
  [SCSI] async: make async_synchronize_full() flush all work regardless of domain
  [SCSI] async: introduce 'async_domain' type
  [SCSI] bfa: Fix to set correct return error codes and misc cleanup.
  [SCSI] aacraid: Series 7 Async. (performance) mode support
  [SCSI] aha152x: Allow use on 64bit systems
  [SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
  [SCSI] bfa: squelch lockdep complaint with a spin_lock_init
  [SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
  [SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
  [SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
  [SCSI] ufs: reverse the ufshcd_is_device_present logic
  [SCSI] ufs: use module_pci_driver
  [SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
  [SCSI] usb-storage: add support for write cache quirk
  [SCSI] set to WCE if usb cache quirk is present.
  [SCSI] virtio-scsi: hotplug support for virtio-scsi
  [SCSI] virtio-scsi: split scatterlist per target
  ...
2012-07-24 18:11:22 -07:00
Linus Torvalds d14b7a419a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
 "Trivial updates all over the place as usual."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
  Fix typo in include/linux/clk.h .
  pci: hotplug: Fix typo in pci
  iommu: Fix typo in iommu
  video: Fix typo in drivers/video
  Documentation: Add newline at end-of-file to files lacking one
  arm,unicore32: Remove obsolete "select MISC_DEVICES"
  module.c: spelling s/postition/position/g
  cpufreq: Fix typo in cpufreq driver
  trivial: typo in comment in mksysmap
  mach-omap2: Fix typo in debug message and comment
  scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
  Change email address for Steve Glendinning
  Btrfs: fix typo in convert_extent_bit
  via: Remove bogus if check
  netprio_cgroup.c: fix comment typo
  backlight: fix memory leak on obscure error path
  Documentation: asus-laptop.txt references an obsolete Kconfig item
  Documentation: ManagementStyle: fixed typo
  mm/vmscan: cleanup comment error in balance_pgdat
  mm: cleanup on the comments of zone_reclaim_stat
  ...
2012-07-24 13:34:56 -07:00
Linus Torvalds 3c4cfadef6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking changes from David S Miller:

 1) Remove the ipv4 routing cache.  Now lookups go directly into the FIB
    trie and use prebuilt routes cached there.

    No more garbage collection, no more rDOS attacks on the routing
    cache.  Instead we now get predictable and consistent performance,
    no matter what the pattern of traffic we service.

    This has been almost 2 years in the making.  Special thanks to
    Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
    have helped along the way.

    I'm sure that with a change of this magnitude there will be some
    kind of fallout, but such things ought the be simple to fix at this
    point.  Luckily I'm not European so I'll be around all of August to
    fix things :-)

    The major stages of this work here are each fronted by a forced
    merge commit whose commit message contains a top-level description
    of the motivations and implementation issues.

 2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
    input.

 3) TCP SYN/ACK performance tweaks from Eric Dumazet.

 4) Add namespace support for netfilter L4 conntrack helpers, from Gao
    Feng.

 5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
    Yuval Mintz.

 6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.

 7) Support for connection tracker helpers in userspace, from Pablo
    Neira Ayuso.

 8) Allow userspace driven TX load balancing functions in TEAM driver,
    from Jiri Pirko.

 9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
    embedded gotos.

10) TCP Small Queues, essentially minimize the amount of TCP data queued
    up in the packet scheduler layer.  Whereas the existing BQL (Byte
    Queue Limits) limits the pkt_sched --> netdevice queuing levels,
    this controls the TCP --> pkt_sched queueing levels.

    From Eric Dumazet.

11) Reduce the number of get_page/put_page ops done on SKB fragments,
    from Alexander Duyck.

12) Implement protection against blind resets in TCP (RFC 5961), from
    Eric Dumazet.

13) Support the client side of TCP Fast Open, basically the ability to
    send data in the SYN exchange, from Yuchung Cheng.

    Basically, the sender queues up data with a sendmsg() call using
    MSG_FASTOPEN, then they do the connect() which emits the queued up
    fastopen data.

14) Avoid all the problems we get into in TCP when timers or PMTU events
    hit a locked socket.  The TCP Small Queues changes added a
    tcp_release_cb() that allows us to queue work up to the
    release_sock() caller, and that's what we use here too.  From Eric
    Dumazet.

15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
  genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
  r8169: revert "add byte queue limit support".
  ipv4: Change rt->rt_iif encoding.
  net: Make skb->skb_iif always track skb->dev
  ipv4: Prepare for change of rt->rt_iif encoding.
  ipv4: Remove all RTCF_DIRECTSRC handliing.
  ipv4: Really ignore ICMP address requests/replies.
  decnet: Don't set RTCF_DIRECTSRC.
  net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
  ipv4: Remove redundant assignment
  rds: set correct msg_namelen
  openvswitch: potential NULL deref in sample()
  tcp: dont drop MTU reduction indications
  bnx2x: Add new 57840 device IDs
  tcp: avoid oops in tcp_metrics and reset tcpm_stamp
  niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
  niu: Fix to check for dma mapping errors.
  net: Fix references to out-of-scope variables in put_cmsg_compat()
  net: ethernet: davinci_emac: add pm_runtime support
  net: ethernet: davinci_emac: Remove unnecessary #include
  ...
2012-07-24 10:01:50 -07:00
Linus Torvalds cb47c1831f Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull target updates from Nicholas Bellinger:
 "There have been lots of work in a number of areas this past round.
  The highlights include:

   - Break out target_core_cdb.c emulation into SPC/SBC ops (hch)
   - Add a parse_cdb method to target backend drivers (hch)
   - Move sync_cache + write_same + unmap into spc_ops (hch)
   - Use target_execute_cmd for WRITEs in iscsi_target + srpt (hch)
   - Offload WRITE I/O backend submission in tcm_qla2xxx + tcm_fc (hch +
     nab)
   - Refactor core_update_device_list_for_node() into enable/disable
     funcs (agrover)
   - Replace the TCM processing thread with a TMR work queue (hch)
   - Fix regression in transport_add_device_to_core_hba from TMR
     conversion (DanC)
   - Remove racy, now-redundant check of sess_tearing_down with qla2xxx
     (roland)
   - Add range checking, fix reading of data len + possible underflow in
     UNMAP (roland)
   - Allow for target_submit_cmd() returning errors + convert fabrics
     (roland + nab)
   - Drop bogus struct file usage for iSCSI/SCTP (viro)"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (54 commits)
  iscsi-target: Drop bogus struct file usage for iSCSI/SCTP
  target: NULL dereference on error path
  target: Allow for target_submit_cmd() returning errors
  target: Check number of unmap descriptors against our limit
  target: Fix possible integer underflow in UNMAP emulation
  target: Fix reading of data length fields for UNMAP commands
  target: Add range checking to UNMAP emulation
  target: Add generation of LOGICAL BLOCK ADDRESS OUT OF RANGE
  target: Make unnecessarily global se_dev_align_max_sectors() static
  target: Remove se_session.sess_wait_list
  qla2xxx: Remove racy, now-redundant check of sess_tearing_down
  target: Check sess_tearing_down in target_get_sess_cmd()
  sbp-target: Consolidate duplicated error path code in sbp_handle_command()
  target: Un-export target_get_sess_cmd()
  qla2xxx: Get rid of redundant qla_tgt_sess.tearing_down
  target: Make core_disable_device_list_for_node use pre-refactoring lock ordering
  target: refactor core_update_device_list_for_node()
  target: Eliminate else using boolean logic
  target: Misc retval cleanups
  target: Remove hba param from core_dev_add_lun
  ...
2012-07-22 13:31:57 -07:00
Dan Williams e96eb23d82 [SCSI] Revert "[SCSI] fix async probe regression"
This reverts commit 43a8d39d01.

Commit 43a8d39d fixed the fact that wait_for_device_probe() was unable
to flush sd probe work.  Now that sd probe work is once again flushable
via wait_for_device_probe() this workaround is no longer needed.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:25:56 +01:00
Dan Williams 492d542273 [SCSI] cleanup usages of scsi_complete_async_scans
Now that scsi registers its async scan work with the async subsystem,
wait_for_device_probe() is sufficient for ensuring all scanning is
complete.

[jejb: fix merge problems with eea03c20ae Make wait_for_device_probe() also do scsi_complete_async_scans()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:25:22 +01:00
Krzysztof Wilczynski b631cf1f89 scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
This is to change use of "0x%08x" in favour of "%p" as per ../Documentation/printk-formats.txt,
which also takes care about the following warning during compilation time:

  drivers/scsi/aha152x.c: In function ‘get_command’:
  drivers/scsi/aha152x.c:2987: warning: cast from pointer to integer of different size

Signed-off-by: Krzysztof Wilczynski <krzysztof.wilczynski@linux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2012-07-20 10:19:25 +02:00
Dan Williams 6cdd55205d [SCSI] queue async scan work to an async_schedule domain
This is preparation to enable async_synchronize_full() to be used as a
replacement for scsi_complete_async_scans(), i.e. to stop leaking scsi
internal details where they are not needed.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:09:27 +01:00
Dan Williams a4683487f9 [SCSI] async: make async_synchronize_full() flush all work regardless of domain
In response to an async related regression James noted:

  "My theory is that this is an init problem: The assumption in a lot of
   our code is that async_synchronize_full() waits for everything ... even
   the domain specific async schedules, which isn't true."

...so make this assumption true.

Each domain, including the default one, registers itself on a global domain
list when work is scheduled.  Once all entries complete it exits that
list.  Waiting for the list to be empty syncs all in-flight work across
all domains.

Domains can opt-out of global syncing if they are declared as exclusive
ASYNC_DOMAIN_EXCLUSIVE().  All stack-based domains have been declared
exclusive since the domain may go out of scope as soon as the last work
item completes.

Statically declared domains are mostly ok, but async_unregister_domain()
is there to close any theoretical races with pending
async_synchronize_full waiters at module removal time.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Eldad Zack <eldadzack@gmail.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:07:37 +01:00
Dan Williams 2955b47d2c [SCSI] async: introduce 'async_domain' type
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain.  This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.

The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.

[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:05:54 +01:00
Krishna Gudipati 529f9a7655 [SCSI] bfa: Fix to set correct return error codes and misc cleanup.
- Remove unnecessary if NULL check in function bfa_fcs_vport_free().
- Set correct return error codes in case of memory allocation failure
  in the BSG ELS/CT passthru command handler.

Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:05 +01:00
Mahesh Rajashekhara 85d22bbf67 [SCSI] aacraid: Series 7 Async. (performance) mode support
- Series 7 Async. (performance) mode support added
- New scatter/gather list format for Series 7
- Driver converts s/g list to a firmware suitable list for best performance on
  Series 7, this can be disabled with driver parameter "aac_convert_sgl" for
  testing purposes
- New container read/write command structure for Series 7
- Fast response support for the SCSI pass-through path added
- Async. status response buffer changes

Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:04 +01:00
Alan Cox fa7250d694 [SCSI] aha152x: Allow use on 64bit systems
This is reported to work, known to work on PCMCIA and a code check shows no
problems on the other bits of the code.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:04 +01:00
Nicholas Bellinger 59057fbc37 [SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
This patch changes virtio-scsi to use a new virtio_driver->scan() callback
so that scsi_scan_host() can be properly invoked once virtio_dev_probe() has
set add_status(dev, VIRTIO_CONFIG_S_DRIVER_OK) to signal active virtio-ring
operation, instead of from within virtscsi_probe().

This fixes a bug where SCSI LUN scanning for both virtio-scsi-raw and
virtio-scsi/tcm_vhost setups was happening before VIRTIO_CONFIG_S_DRIVER_OK
had been set, causing VIRTIO_SCSI_S_BAD_TARGET to occur.  This fixes a bug
with virtio-scsi/tcm_vhost where LUN scan was not detecting LUNs.

Tested with virtio-scsi-raw + virtio-scsi/tcm_vhost w/ IBLOCK on 3.5-rc2 code.

Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:03 +01:00
Kyle McMartin 0b1017aab1 [SCSI] bfa: squelch lockdep complaint with a spin_lock_init
Spotted this while looking at another issue...

INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 298, comm: udevd Not tainted 3.3.0 #1
Call Trace:
  [<ffffffff810cee63>] __lock_acquire+0x1363/0x1bb0
  [<ffffffff816593d2>] ? __slab_alloc+0x4a0/0x4fd
  [<ffffffff81020063>] ? native_sched_clock+0x13/0x80
  [<ffffffff810200d9>] ? sched_clock+0x9/0x10
  [<ffffffff810cfd81>] lock_acquire+0xa1/0x1e0
  [<ffffffffa0321b83>] ? bfa_fcs_lport_aen_post+0x43/0x160 [bfa]
  [<ffffffff816630e5>] _raw_spin_lock_irqsave+0x65/0xb0
  [<ffffffffa0321b83>] ? bfa_fcs_lport_aen_post+0x43/0x160 [bfa]
  [<ffffffffa0321b83>] bfa_fcs_lport_aen_post+0x43/0x160 [bfa]
  [<ffffffffa032fa57>] bfa_fcs_lport_init+0x97/0x120 [bfa]
  [<ffffffffa031d4ff>] bfa_fcs_fabric_sm_uninit+0x1cf/0x250 [bfa]
  [<ffffffffa031c1da>] bfa_fcs_fabric_modinit+0x2a/0xb0 [bfa]
  [<ffffffffa031bef2>] ? bfa_fcs_fabric_attach+0xf2/0x170 [bfa]
  [<ffffffffa031e75a>] bfa_fcs_init+0x2a/0x40 [bfa]
  [<ffffffffa02facf7>] bfad_drv_init+0x107/0x1f0 [bfa]
  [<ffffffffa02fb057>] bfad_pci_probe+0x277/0x450 [bfa]
  [<ffffffff81354d4c>] local_pci_probe+0x5c/0xd0
  [<ffffffff81354ed1>] pci_device_probe+0x111/0x120
  [<ffffffff8141c0e6>] driver_probe_device+0x96/0x2f0
  [<ffffffff8141c3eb>] __driver_attach+0xab/0xb0
  [<ffffffff8141c340>] ? driver_probe_device+0x2f0/0x2f0
  [<ffffffff8141a2e5>] bus_for_each_dev+0x55/0x90
  [<ffffffffa037b000>] ? 0xffffffffa037afff
  [<ffffffff8141bbce>] driver_attach+0x1e/0x20
  [<ffffffff8141b8d8>] bus_add_driver+0x1b8/0x2b0
  [<ffffffffa037b000>] ? 0xffffffffa037afff
  [<ffffffff8141cbc7>] driver_register+0x77/0x160
  [<ffffffffa037b000>] ? 0xffffffffa037afff
  [<ffffffff81353b23>] __pci_register_driver+0x73/0xf0
  [<ffffffffa037b000>] ? 0xffffffffa037afff
  [<ffffffffa037b083>] bfad_init+0x83/0x1000 [bfa]
  [<ffffffff8100212a>] do_one_initcall+0x12a/0x180
  [<ffffffff810df0d0>] sys_init_module+0xc0/0x220
  [<ffffffff8166bbe9>] system_call_fastpath+0x16/0x1b

Signed-off-by: Kyle McMartin <kmcmarti@redhat.com>
Acked-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:03 +01:00
Jon Mason e67f13212a [SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:02 +01:00
Jon Mason 983bfb5b40 [SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.

Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:02 +01:00
Namjae Jeon 94c122ab01 [SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
Currently the UFS host driver has returned incorrect values for SUCCESS
and FAILED.  Fix it to return the correct value to the upper layer.

Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:02 +01:00
Venkatraman S 73ec513a3b [SCSI] ufs: reverse the ufshcd_is_device_present logic
Otherwise it counter intuitively returns 0 if device is present.

Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:01 +01:00
Venkatraman S 17ccafc4ef [SCSI] ufs: use module_pci_driver
Use macro module_pci_driver and get rid of boilerplate code.  No
functional changes.

Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:01 +01:00
Namjae Jeon b81478d82e [SCSI] set to WCE if usb cache quirk is present.
Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.

Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:59:00 +01:00
Cong Meng 365a715009 [SCSI] virtio-scsi: hotplug support for virtio-scsi
This patch implements the hotplug support for virtio-scsi.
When there is a device attached/detached, the virtio-scsi driver will be
signaled via event virtual queue and it will add/remove the scsi device
in question automatically.

Signed-off-by: Sen Wang <senwang@linux.vnet.ibm.com>
Signed-off-by: Cong Meng <mc@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:58 +01:00
Paolo Bonzini 2bd37f0fde [SCSI] virtio-scsi: split scatterlist per target
To improve performance for I/O to different targets, add a separate
scatterlist for each of them.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:58 +01:00
Paolo Bonzini bce750b163 [SCSI] virtio-scsi: release sg_lock after add_buf
We do not need the sglist after calling virtqueue_add_buf.  Hence we
can "pipeline" the locked operations and start preparing the sglist
for the next request while we kick the virtqueue.

Together with the previous two patches, this improves performance as
follows.  For a simple "if=/dev/sda of=/dev/null bs=128M iflag=direct"
(the source being a 10G disk, residing entirely in the host buffer cache),
the additional locking does not cause any penalty with only one dd
process, but 2 simultaneous I/O operations improve their times by 3%:

               number of simultaneous dd
                   1               2
 ----------------------------------------
 current        5.9958s        10.2640s
 patched        5.9531s         9.8663s

(Times are best of 10).

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:57 +01:00
Paolo Bonzini 139fe45abc [SCSI] virtio-scsi: split locking per vq
Keep a separate lock for each virtqueue.  While not particularly
important now, it prepares the code for when we will add support
for multiple request queues.  It is also more tidy as soon as
we introduce a separate lock for the sglist.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:57 +01:00
Paolo Bonzini b5ee8f2802 [SCSI] virtio-scsi: unlock during kick
Separate virtqueue_kick_prepare from virtqueue_notify, so that the
expensive vmexit is done without holding the lock.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:57 +01:00
Yi Zou a752359f2b [SCSI] libfc: fix sending REC after FCP_RESP is received
This is exposed in the case the FCP_DATA frames somehow got lost and fc_fcp got
the FCP_RSP, in fc_fcp_recv_resp(), since xfer_len is less than the expected_len
it resets the the timer to wait to 2 more jiffies in case the data frames are
already queued locally. However, for target does not support REC, it would just
send RJT w/ ELS_RJT_UNSUP. The rec response handler thus only clears the rport
flag for not doing REC later, but does not do fcp_io_complete() on the
associated fsp.

The fix is just check status of FCP_RSP being received already, i.e. using the
FC_SRB_RCV_STATUS flag, in fc_fcp_timeout before start sending REC. We should
have waited long enough if there is truely data frames queued locally.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Vasu Dev ac166d2fbd [SCSI] libfc: fix retries with FDMI lport states
The FC-GS-3 sepc requires to wait for least 3 times R_A_TOV per
sec 4.6.1 "If the Requesting_CT does not receive a Response
CT_IU from the Responding_CT within three times R_A_TOV,
it shall consider this to be a protocol error."

This means added four new states with management server
could add significant delay with multiple retries
on default 12 second timeout(3 * R_A_TOV), so instead
just skip these states on very first timeout on any of
these states to not stuck with states for such longer
period.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Yi Zou db95fc004e [SCSI] libfc: don't exch_done() on invalid sequence ptr
The lport_recv(), i.e., fc_lport_recv_req() may get called w/o the sequence ptr
being set in fr_seq(), particularly in the case of vn2vn mode, this may happen
if the passive fcp provider, e.g., tcm_fc, has not been registered yet.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Neil Horman 95fdd5e980 [SCSI] fcoe: Cleanup locking on fcoe_percpu_receive_thread
Noticed that we can shuffle the code around in fcoe_percpu_receive_thread a bit
and avoid taking the fcoe_rx_list lock twice per iteration.  This should improve
throughput somewhat.  With this change we take the lock, and check for new
frames in a single critical section.  Only if the list is empty do we drop the
lock and re-acquire it after being signaled to wake up.

Change Notes:
v2) did some further cleanup on the patch by replacing the 2nd call of
spin_lock/splice_init with a goto to the top of the outer loop.  This allows me
to change the inner while loop to an if conditional and remove the sencond check
of kthread_should_stop.  Based on suggestion from Vasu Dev.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:55 +01:00
Robert Love 902a45af5c [SCSI] fcoe: Remove redundant 'less than zero' check
strtoul returns an 'unsigned long' so there is no
reason to check if the value is less than zero.

strtoul already checks for the '-' character deep
in its bowels. It will return an error if the user
has provided a negative value and fcoe_str_to_dev_loss
will return that error to its caller.

This patch fixes the following Coverity reported warning:

CID 703581 -  NO_EFFECT Unsigned compared against 0 - This
less-than-zero comparison of an unsigned value is never true. "*val < 0UL".
drivers/scsi/fcoe/fcoe_sysfs.c:105

Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:55 +01:00
Vasu Dev b29a4f309f [SCSI] libfc: add exch timer debug info
Add exch timeout info to have debug log with exch timeout
value to match with retries, also add debug info
on exch timer cancel.

Added common fc_exch_timer_cancel() func and grouped this
along with fc_exch_timer_set() function, so that
added debug code is not repeated.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:55 +01:00
Lin Ming 33a2285d96 [SCSI] scsi_pm: set device runtime state before parent suspended
There is a race in scsi_bus_resume_common when set device's runtime
state to active after pm_runtime_put_sync(dev->parent).

Parent device may have been suspended so pm_runtime_set_active(dev) will
fail with -EBUSY.

Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:55 +01:00
James Bottomley 4bdd03e61b [SCSI] lpfc: fix problems with -Werror
Commit d38bd3aef ("Add -Werror compilation flag") is causing build breakage
with random gcc incarnations.  These look like gcc problems, but we shouldn't
break the build because of a bad gcc.  Fix this by adding a make flag

WARNINGS_BECOME_ERRORS=1

which is the same as aic7xxx uses so ordinarily the build doesn't use -Werror

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Alex Iannicelli <alex.iannicelli@emulex.com>
Cc: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:54 +01:00
Dan Carpenter cca85013ef [SCSI] mvsas: remove unused variable in mvs_task_exec()
We don't use "dev" any more after 07ec747a5f ("libsas: remove
ata_port.lock management duties from lldds") and it causes a compile
warning.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:54 +01:00
Dan Williams f0bf750c2d [SCSI] libsas: trim sas_task of slow path infrastructure
The timer and the completion are only used for slow path tasks (smp, and
lldd tmfs), yet we incur the allocation space and cpu setup time for
every fast path task.

Cc: Xiangliang Yu <yuxiangl@marvell.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:54 +01:00
Dan Williams a494fd5bd9 [SCSI] libsas: drop sata port multiplier infrastructure
On the way to add a new sata_device field, noticed that libsas is
carrying port multiplier infrastructure that is explicitly disabled by
sas_discover_sata().  The aic94xx touches the unused port_no, so leave
that field in case there was some use for it.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:53 +01:00
Dan Williams b17caa174a [SCSI] libsas: fix sas_discover_devices return code handling
commit 198439e4 [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
commit 19252de6 [SCSI] libsas: fix wide port hotplug issues

The above commits seem to have confused the return value of
sas_ex_discover_dev which is non-zero on failure and
sas_ex_join_wide_port which just indicates short circuiting discovery on
already established ports.  The result is random discovery failures
depending on configuration.

Calls to sas_ex_join_wide_port are the source of the trouble as its
return value is errantly assigned to 'res'.  Convert it to bool and stop
returning its result up the stack.

Cc: <stable@vger.kernel.org>
Tested-by: Dan Melnic <dan.melnic@amd.com>
Reported-by: Dan Melnic <dan.melnic@amd.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:53 +01:00
Dan Williams 26f2f199ff [SCSI] libsas: continue revalidation
Continue running revalidation until no more broadcast devices are
discovered.  Fixes cases where re-discovery completes too early in a
domain with multiple expanders with pending re-discovery events.
Servicing BCNs can get backed up behind error recovery.

Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:52 +01:00
Jeff Skirvin b2311a2875 [SCSI] libsas: sas_rediscover_dev did not look at the SMP exec status.
The discovery function "sas_rediscover_dev" had two bugs: 1) it did
not pay attention to the return status from the SMP task execution;
2) the stack variable used for the returned SAS address was compared
against 0 without being initialized.

Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:52 +01:00