Make sure definitions are consistent with usage.
Detected with Sparse.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When module size > DMA buffer size, driver copies first chunk and waits
for the BDL complete interrupt. BDL complete interrupt never occurs and
wait time expires as module load IPC is not send to start the DMA from
DSP.
To fix the above issue need to follow the below steps:
1. After copying the first chunk, send the module load IPC to start the
DMA.
2. Wait for the BDL interrupt. Once interrupt is received, copy the
next chunk.
3. Continue step 2 till all bytes are copied.
4. When all the bytes are copied (bytes_left = 0), wait for module load
IPC response
5. Handled module load IPC response messages, check the load module IPC
response and wake up the thread to complete module load.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trival fix, some dev_* messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds clean up routine to clear the stream registers and
calls this routine before setting up stream registers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds polling of CLDMA stream run bit when set
to confirm the HW reports the same value.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake driver uses snd_dma_buffer for data and buffer, these are variables
and not pointer so do not test field addresses.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When downloading the firmware/module, if the ring buffer boundary
is reached, we need to wrap to the zeroth position. On next copy
we need to copy till end of buffer and the remaining buffer needs
to be copied from zeroth position.
In this case copy was not handled correctly when wrap condition
is reached which caused invalid data to be copied resulting in
invalid hash failure.
This patch fixes the issue by handling copy at the boundary
condition correctly.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During firmware download, dma buffers are allocated in prepare
and never freed on clean up. This patch frees the allocated dma
buffer in cldma controller clean up.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the last piece of code loader DMA APIs by adding the code
loader DMA APIs for the driver to use
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pierre-Louis Bossart
Jeeja KP
Takashi Iwai
Colin Ian King
Vinod Koul