I have a laptop HP Compaq 8710W, I compiled into my kernel the LIS3LV02DL
and HP_ACCEL module drivers. While loading it cannot recognize the laptop
model, so i am sending the necessary information to update the database of
axis orientations.
>When the laptop is horizontal the position reported is about 0 for X and Y
>and a positive value for Z
Yes, it is about 0,0,1000, the actual reading says: (-17,-26,1018);
> If the left side is elevated, X increases (becomes positive)
Yes, X goes toward to positive 1000.
>If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
No, Y goes toward to positive 1000.
>If the laptop is put upside-down, Z becomes negative
Yes, the laptop on a table Z gives 1000, and if upsidedown the Z reads
-1000.
So in few words the Y axis is inverted.
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two more laptops to whitelist.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Linux support for the Linear Technology LTC4215 Hot Swap controller
I2C monitoring interface.
I have tested the driver with my board, and it appears to work fine. With
the power supplies disabled, it reads 11.93V input, 1.93V output, no
current and no power. With the supplies enabled, it reads 11.93V input,
11.98V output, no current, no power. I'm not drawing any current at the
moment, so this is reasonable. The value in the sense register never
reads anything except 0, so I expect to get zero from the current and
power calculations.
I didn't attempt to support changing any of the chip's settings or
enabling the FET. I'm not sure even how to do that and still fit within
the hwmon framework. :)
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An hwmon driver for the National Semiconductor LM95241 triple temperature
sensors chip
Signed-off-by: Davide Rizzo <elpa-rizzo@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As Andrew noted, adev is pretty poor name for symbol being exported.
Rename it to lis3.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Vladimir Botka <vbotka@suse.cz>
Cc: <Quoc.Pham@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many thanks to Fujitsu Siemens Computers for providing docs and a
machine to test the driver on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
At the moment, dmi_walk() lacks flexibility, users can't pass data to
the callback function. Add a pointer for private data to make this
function more flexible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Roland Dreier <rolandd@cisco.com>
Directory drivers/i2c/chips is going away, so drivers there must find
new homes. For the pcf8591 driver, the best choice seems to be the
hwmon subsystem. While the Philips PCF8591 device isn't a typical
hardware monitoring chip, its DAC interface is compatible with the
hwmon one, so it fits somewhat.
If a better subsystem is ever created for ADC/DAC chips, the driver
could be moved there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
The pin for in6 and temp3 is shared on the W83667HG, so only one of
these features can be supported on any given system. Let the driver
select which one depending on the temp3 disabled bit.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add initial support for the Nuvoton W83667HG chip to the w83627ehf
driver. It has been tested on ASUS P5QL PRO by Gong Jun.
At the moment there is still a usability issue which is that only in6
or temp3 can be present on the W83667HG, so the driver shouldn't
expose both. This will be addressed later.
Signed-off-by: Gong Jun <JGong@nuvoton.com>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use positive logic for fan pin variables (variable is set if pin is
used for fan), instead of negative logic which is error prone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Gong Jun <JGong@nuvoton.com>
Fix for kernel.org bug #7154: hdaps inversion of actual Thinkpad
X41's Y-axis.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix for kernel.org bug #7154: hdaps inversion of each axis. This
version is based on the work from Michael Ruoss <miruoss@student.ethz.ch>.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Register access over SMBus isn't cheap, so avoid register access where
possible:
* Only write back the configuration register if it changed.
* Don't refresh the register cache when we don't have to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Fix a few oddities in how the ds1621 driver accesses the registers:
* We don't need a wrapper to access the configuration register.
* Check for error before calling swab16. Error checking isn't
complete yet, but that's a start.
* Device-specific read functions should never be called during
detection, as by definition we don't know what device we are talking
to at that point.
* Likewise, don't assume that register reads succeed during detection.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reorder the ds1621 driver code so that we can get rid of forward
function declarations.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.
The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The verstep check in the lm85 driver fails because the upper nibble of
the version register is 0x7, not 0x6, on the adt7468 chip. Probing of
all adt7468s was broken by 69fc1feba2
("hwmon: (lm85) Rework the device detection"), and this patch fixes
that. Also add in a missing i2c_device_id that accidentally got dropped
from the original patch.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for HP Pavilion dv5.
Since Intel-based models have an inverted x axis, while AMD-based models
have an inverted y axis, we introduce a new macro that special-cases axis
orientation based on two DMI entries: HP dv5 axis configuration is then
based on both the PRODUCT and BOARD name.
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Cc: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Tested-by: Palatis Tseng <palatis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sensors responding with 0x3B to WHO_AM_I only have one data register per
direction, thus returning a signed byte from the position which is
occupied by the MSB in sensors responding with 0x3A.
Since multiple sensors share the reply to WHO_AM_I, we rename the defines
to better indicate what they identify (family of single and double
precision sensors).
We support both kind of sensors by checking for the sensor type on init
and defining appropriate data-access routines and sensor limits (for the
joystick) depending on what we find.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Giuseppe Bilotta <giuseppe.bilotta@gmail.com>
Acked-by: Eric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds freefall handling to hp_accel driver. According to HP, it
should just work, without us having to set the chip up by hand.
hpfall.c is example .c program that parks the disk when accelerometer
detects free fall. It should work; for now, it uses fixed 20seconds
protection period.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a number of cases where things were not properly
cleaned up when acpi_check_resource_conflict() returned an error,
causing oopses such as the one reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=483208
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If the F71882FG chip is at address 0x4e, then the probe at 0x2e will
fail with the following message in the logs:
f71882fg: Not a Fintek device
This is misleading because there is a Fintek device, just at a
different address. So I propose to degrade this message to a debug
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the HP laptops of model 6710x for having correctly setup
axes.
Signed-off-by: Martin Kebert <gkmarty@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6730x for having correctly setup
axes.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the HP laptops of model 6530x for having correctly setup
axes.
Reported-by: Jerome Poulin <jeromepoulin@gmail.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to dmesg my laptop model HP 6510b is not being recognized by this
driver. After I have modified "lis3lv02d.c" axes in Neverball are OK.
Signed-off-by: Jiri Tersel <tersel@mail.muni.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed. This patch add supports for the newer
temperature sensors in the MacPro3.
Signed-off-by: Bharath Ramesh <bramesh@vt.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) Fix CONFIG_DMI=n fallback to probe
hwmon: (abituguru3) Enable DMI probing feature on IN9 32X MAX
hwmon: (abituguru3) Match partial DMI board name strings
hwmon: Add a driver for the ADT7475 hardware monitoring chip
hwmon: (k8temp) Fix temperature reporting for (most) K8 RevG CPUs
hwmon: (k8temp) Fix wrong sensor selection for AMD K8 RevF/RevG CPUs
hwmon: (k8temp) Warn about fam F rev F errata
The LED on HP notebooks is connected through ACPI. That unfortunately
means that it needs to be delayed by using schedule_work() to avoid
calling the ACPI interpreter from an invalid context.
[akpm@linux-foundation.org: use flush_work() rather than sort-of reimplementing it]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the second part of the HP laptop disk protection functionality (a red
led) to the same driver. From a purely Linux developer's point of view,
the led and the accelerometer have nothing related. However, they
correspond to the same ACPI functionality, and so will always be used
together, moreover as they share the same ACPI PNP alias, there is no
other simple to allow to have same loaded at the same time if they are not
in the same module. Also make it requires the led class to compile and
update the Kconfig text.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The light sensors ALV0 and ALV1 on newer MacBooks (early 2008 and later)
changed to report 10 bytes instead the earlier 6, and the sensor encoding
subsequently changed. As a result, the reported light sensors readings
are much too low.
Via experiments leading up to this patch, it seems only the ALV0 is
reporting data, and the most useful value therein is a 10-bit big-endian
value at offset 6. This suggests that a new protocol was added as a
backward-compatible replacement on top of the old one.
This patch makes applesmc report the improved light sensor reading for the
new machines, on a scale in conformance with earlier ones.
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_DMI is not enabled, dmi detection should flag that no board
could be detected (err=1) rather than another error condition (err<0).
This fixes the fallback to manual probing for all motherboards, even
those without DMI strings, when CONFIG_DMI=n.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Switch the IN9 32X MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Paul Hartman <paul.hartman+gentoo@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The switch-over to using DMI board strings to identify abituguru3 compatible
mainboards works most of the time, but sometimes the vendor has substantially
modified the board string between BIOS revisions.
We have found that the vendor chipset identification string (provided in
brackets) changes frequently and is of no use to us. The rest of the board
string sometimes changes in subtle ways, e.g. whitespace or variations in
capitalization.
The new comparison code checks only a part of the supplied DMI board string,
trimming the bracketed content, whitespace, and ignoring case as necessary.
This fixes a bug where an IP35 Pro running an early BIOS would not be
detected without the force=1 module parameter, and also speculatively
fixes other similiar issues.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Nick Pasich <NewsLetters@nickandbarb.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Hwmon driver for the ADT7475 chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Current Temperature for K8 RevG desktop CPUs is a "normalized value"
which can be below ambient temperature.
As a consequence lots of RevG systems report temperatures like:
$ sensors
k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp: +17 C
Core0 Temp: +3 C
Core1 Temp: +21 C
Core1 Temp: +5 C
being quite below ambient temperature.
There are even reports of negative temperature values.
This patch corrects the temperature reporting of k8temp for
RevG desktop CPUs.
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Meaning of ThermSenseCoreSel bit was inverted beginning with K8 RevF.
That means with current driver temp1/temp2 belong to core 1 and
temp3/temp4 belong to core 0 on a K8 RevF/RevG CPU.
This patch ensures that temp1/temp2 always belong to core 0 and
temp3/temp4 to core 1 for all K8 revisions.
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add warning about wrong CPU temperature readouts on all fam F rev F.
The allowed combinations of processors ensure that all processors
in a multisocket system have similar characteristics, e.g.
(1) provide temperature sensor interface (>=RevC && <RevF)
(2) are affected by erratum #141 (>=RevF)
Thus it is sufficient to check the revision of the boot CPU.
For "mixed silicon support" refer to
"Revision Guide for AMD Athlon 64 and AMD Opteron Processors" (RevA-E) and
"Revision Guide for AMD NPT Family 0Fh Processors" (RefF-G).
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The sensor can be accessed via various buses. In particular, SPI, I²C
and, on HP laptops, via a specific ACPI API (the only one currently
supported). Separate this latest platform from the core of the sensor
driver to allow support for the other bus type. The second, and more
direct goal is actually to be able to merge this part with the
hp-disk-leds driver, which has the same ACPI PNP number.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (29 commits)
hwmon: Fix various typos
hwmon: Check for ACPI resource conflicts
hwmon: (lm70) Add TI TMP121 support
hwmon: (lm70) Code streamlining and cleanup
hwmon: Deprecate the fscher and fscpos drivers
hwmon: (fschmd) Add watchdog support
hwmon: (fschmd) Cleanups for watchdog support
hwmon: (i5k_amb) Load automatically on all 5000/5400 chipsets
hwmon: (it87) Add support for the ITE IT8720F
hwmon: Don't overuse I2C_CLIENT_MODULE_PARM
hwmon: Add LTC4245 driver
hwmon: (f71882fg) Fix fan_to/from_reg prototypes
hwmon: (f71882fg) Printout fan modes
hwmon: (f71882fg) Add documentation
hwmon: (f71882fg) Fix auto_channels_temp temp numbering with f8000
hwmon: (f71882fg) Add missing pwm3 attr for f71862fg
hwmon: (f71882fg) Add F8000 support
hwmon: (f71882fg) Remove the fan_mode module option
hwmon: (f71882fg) Separate max and crit alarm and beep
hwmon: (f71882fg) Check for hwmon powerdown state
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
The Texas Instruments TMP121 is a SPI temperature sensor very similar
to the LM70, with slightly higher resolution. This patch extends the
LM70 driver to support the TMP121. The TMP123 differs in pin assign-
ment.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Now that the new merged fschmd driver has gained support for the watchdog
integrated into these IC's, there is no more reason to keep the old fscher
and fscpos drivers around, so mark them as deprecated.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the watchdog part found in _all_ supported FSC
sensor chips.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups in preparation of adding watchdog support,
mostly removing _MASK postfix from defines which are not masks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It turns out that we cannot create a pci_driver in this driver because PCI will
not call this module's probe function if the i5000-edac driver is already
loaded. That said, we only want one value (AMBASE) from the PCI config space.
Neither driver alters this value, so it's safe to read it. However, we still
want the module aliases, so provide that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I2C_CLIENT_MODULE_PARM is overkill for force_subclients. We really
only use 4 out of the 48 slots, so we're better defining a custom
variable instead. This change saves 92 bytes of data for each of the
five drivers affected.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Add Linux support for the Linear Technology LTC4245 Multiple Supply Hot
Swap controller I2C monitoring interface.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The RPM after conversion from / before conversion to a register value can be
much more than 65535 (up to 1500000), so putting this into an u16 can cause
overflows. This changes the functions to use an int to store / get RPM instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Print the mode (duty-cycle or RPM) of each fan on driver load.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add some documentation about the f71882fg driver, and update the Kconfig
documentation to report the new supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adjust auto_channels_temp show and store functions for different numbering of
temps between f8000 and other supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For some reason the fan_attr array for the f71862fg was missing the attr for
the 3th pwm output. This patch fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
And (finally) the patch actually adding f8000 support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the fan_mode module option it was a monstrosity to begin with, and
when adding support for the F8000 it becomes a real pain!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While studying the datasheets for adding F8000 support, I noticed that the
F718x2 has separate alarms (and beep control) for its max and crit limits.
We keep the temp#_alarm attributes as they are, even though it would be more
logical to rename them to temp#_max_alarm. Because lm_sensors v2 depends
on them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More F8000 prep work. Take over the checking if the hwmon part is not
powered down from the standalone f8000 driver.
This check is valid for all supported models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Simplify fan and temp hyst. handling by treating the registers as an array of
nibbles instead of using switch cases. Also unify the way hysts are handled
between temp and fans, the temp code was storing the actual per temp hyst
values in 4 u8's, where as the fan code was storing actual register values.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on adding F8000 support I noticed that various of the
store sysfs functions (and a few of the show also) had issues.
This patch fixes the following issues in these functions:
* store: storing the result of strto[u]l in an int, resulting in a possible
overflow before boundary checking
* store: use of f71882fg_update_device(), we don't want to read the whole
device in store functions, just the registers we need
* store: use of cached register values instead of reading the needed regs
in the store function, including cases where f71882fg_update_device() was
not used, this could cause real isues
* show: shown value is a calculation of 2 or more cached register reads,
without locking the data struct.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch is a preparation patch for adding F8000 support to the f71882fg
driver. If you look at the register addresses and esp, the bits used for
the temperature channels, then you will notice that it appears that they
start at 1 in a system meant to start at 0. As the F8000 actually uses the 0
addresses and bits, this patch changes the f71882fg driver to take 4
temperatures numbered 0-3 in to account, using 1-3 in this new scheme for
the temperatures actually present in the F718x2FG.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The f71882fg driver did some io to ioports it hadn't reserved yet in its
find (detect) function, this patches moves this io to the probe function
where these ports are reserved and this io belongs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for the Fintek f71862fg superio monitoring
functions to the f71882fg driver.
This support has been tested without problems on a Jetway J9F2 by
Tony McConnell.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Various small cleanups as preparation for adding f71862fg support to the
f71882fg driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM (fan speed control) support to the f71882fg driver. Both
manual control and automatic (temperature-based) modes are supported.
Additionally, each mode has a PWM-based and an RPM-based variant. By
default we use the mode set by the BIOS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
A few cleanups that were originally part of a larger patch but are
better submitted separately.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert f71882fg driver from SENSOR_ATTR to SENSOR_ATTR2 use, this is a
preparation patch for adding pwm support, which is broken out to make what
changes really in the pwm support patch clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Mark van Doesburg <mark.vandoesburg@hetnet.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add temperature sensor support for MacBook Air 2.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that the adt7470's automatic fan control algorithm only works
when the temperature sensors get updated. This in turn happens only when
someone tells the chip to read its temperature sensors. Regrettably, this
means that we have to drive the chip periodically.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7470 driver currently assumes that 1s is the proper time to wait to
read all temperature sensors. However, the correct time is 200ms *
number_of_sensors. This patch sets the default time to provide for 10
sensors and then lowers it based on the number of sensor inputs that have
nozero values.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the small window that it takes to read the temperature sensors, the pwm
outputs momentarily drop to 0. This causes a noticeable hiccup in fan
speed, which is slightly annoying. The solution is to manually program
the pwm output with whatever the automatic value is and then shift the
fans to manual control while reading temperatures. Once that is done, put
the fans back to whatever mode of control was there before.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify some hwmon drivers to use DIV_ROUND_CLOSEST instead of bloating
source with (naughty) macros.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make use of the new dmi device loading support to automatically load the
applesmc driver based on the dmi_match table.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to analyze the SMC of the newer MacPros, applesmc needs to
recognize the machine. This patch adds the missing generic dmi_match
entry for MacPro models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 6.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Caleb Hyde <caleb.hyde@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file(s) below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/hwmon/lis3lv02d.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New driver to play with. As Jean mentioned a couple of years ago, this
chip is a beast with odd combinations of 8 fans, 4 temperatures, and 13
voltage sensors. This driver has been tested on an IntelliStation Z30.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver to the accelerometer sensor found in several HP
laptops (under the commercial names of "HP Mobile Data Protection System
3D" and "HP 3D driveguard"). It tries to have more or less the same
interfaces as the hdaps and other accelerometer drivers: in sysfs and as
a joystick.
This driver was first written by Yan Burman. Eric Piel has updated it
and slimed it up (including the removal of an interface to access to the
free-fall feature of the sensor because it is not reliable enough for
now). Pavel Machek removed few more features and switched locking from
semaphore to mutex.
Several people have contributed to the database of the axes.
[eric.piel@tremplin-utc.net: LIS3LV02D: Conform to the new ACPI API]
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Yan Burman <burman.yan@gmail.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The adt7468 is a follow-on to the adt7463, so plumb in adt7468 support
along the same code paths.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement correct range checking for adt7470 to prevent userland from
writing impossible values into the chip, and cap out-of-range values per
standard hwmon conventions.
Implement correct rounding of input values per standard hwmon conventions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.
This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash. Make this assumption hold true for these
three drivers.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer and temperature sensor support for Macbook 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 8.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Klaus Doblmann <klaus.doblmann@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook Pro 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accelerometer, backlight and temperature sensor support for the new
unibody Macbook 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: David M. Lary <dmlary@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for iMac 5.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Ricky Campbell <johnrcampbell@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The read fail ratio is sensitive to the delay between the first byte
written and the first byte read; apparently the sensors cannot be rushed.
Increasing the minimum wait time, without changing the total wait time,
improves the fail ratio from a 8% chance that any of the sensors fails in
one read, down to 0.4%, on a Macbook Air. On a Macbook Pro 3,1, the
effect is even more apparent. By reducing the number of status polls, the
ratio is further improved to below 0.1%. Finally, increasing the total
wait time brings the fail ratio down to virtually zero.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Bob McElrath <bob@mcelrath.org>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add temperature sensor support for Macbook Pro 3.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temperature sensor support for the Macbook Pro 4.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dmi_system_id.driver_data is already void*.
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerometer, backlight and temperature sensor support
for the Macbook Air.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some recent Macbooks, the package length for the light sensors ALV0 and
ALV1 has changed from 6 to 10. This patch allows for a variable package
length encompassing both variants.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time to wait for a status change while reading or writing to the SMC
ports is a balance between read reliability and system performance. The
current setting yields rougly three errors in a thousand when
simultaneously reading three different temperature values on a Macbook
Air. This patch increases the setting to a value yielding roughly one
error in ten thousand, with no noticable system performance degradation.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On many Macbooks since mid 2007, the Pro, C2D and Air models, applesmc
fails to read some or all SMC ports. This problem has various effects,
such as flooded logfiles, malfunctioning temperature sensors,
accelerometers failing to initialize, and difficulties getting backlight
functionality to work properly.
The root of the problem seems to be the command protocol. The current
code sends out a command byte, then repeatedly polls for an ack before
continuing to send or recieve data. From experiments leading to this
patch, it seems the command protocol never quite worked or changed so that
one now sends a command byte, waits a little bit, polls for an ack, and if
it fails, repeats the whole thing by sending the command byte again.
This patch implements a send_command function according to the new
interpretation of the protocol, and should work also for earlier models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At one single place in the code, the specified number of bytes to read and
the actual number of bytes read differ by one. This one-liner patch fixes
that inconsistency.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds therm-min/max/crit-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the therm_group (of sysfs files)
The thermistors use voltage channels to measure; so they don't have a
fault-alarm, but unlike the other voltages, they do have an overtemp,
which we call crit (by convention).
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
temp and vin status register values may be set by chip specifications, set
again by bios, or by this previously loaded driver. Debug output nicely
displays modprobe init=\d actions.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver handles 3 logical devices in fixed length array. Give this a
define-d constant.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the temp_group (of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations,
and refs to those new decls in the macro used to initialize the vin_group
(of sysfs files)
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring hwmon/pc87360 into agreement with
Documentation/hwmon/sysfs-interface.
Patchset adds separate limit alarms for voltages and temps, it also adds
temp[123]_fault files. On my Soekris, temps 1,2 are unused/unconnected,
so temp[123]_fault = 1,1,0 respectively. This agrees with
/usr/bin/sensors, which has always shown them as OPEN. Temps 4,5,6 are
thermistor based, and dont have a fault bit in their status register.
This patch:
2 different kinds of constants added:
- CHAN_ALM_* constants for (later) vin, temp alarm callbacks.
- CHAN_* conversion constants, used in _init_device, partly for RW1C bits
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.
Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.
[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.
So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.
Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.
This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
