Commit Graph

294 Commits

Author SHA1 Message Date
Yi Zou 3b64b18811 [SCSI] libfc: fix lun reset failure bugs in fc_fcp_resp handling of FCP_RSP_INFO
In LUN RESET testing involving NetApp targets, it is observed that LUN
RESET is failing. The fc_fcp_resp() is not completing the completion
for the LUN RESET task since fc_fcp_resp assumes that the FCP_RSP_INFO
is 8 bytes with the 4 byte reserved field, where in case of NetApp targets
the FCP_RSP to LUN RESET only has 4 bytes of FCP_RSP_INFO. This leads
fc_fcp_resp to error out w/o completing the task completion, eventually
causing LUN RESET to be escalated to host reset, which is not very nice.

Per FCP-3 r04, clause 9.5.15 and Table 23, the FCP_RSP_INFO field can be either
4 bytes or 8 bytes, with the last 4 bytes as "Reserved (if any)". Therefore it
is valid to have 4 bytes FCP_RSP_INFO like some of the NetApp targets behave.
Fixing this by validating the FCP_RSP_INFO against both the two spec allowed
length.

Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-10-07 11:52:55 +01:00
Yi Zou a752359f2b [SCSI] libfc: fix sending REC after FCP_RESP is received
This is exposed in the case the FCP_DATA frames somehow got lost and fc_fcp got
the FCP_RSP, in fc_fcp_recv_resp(), since xfer_len is less than the expected_len
it resets the the timer to wait to 2 more jiffies in case the data frames are
already queued locally. However, for target does not support REC, it would just
send RJT w/ ELS_RJT_UNSUP. The rec response handler thus only clears the rport
flag for not doing REC later, but does not do fcp_io_complete() on the
associated fsp.

The fix is just check status of FCP_RSP being received already, i.e. using the
FC_SRB_RCV_STATUS flag, in fc_fcp_timeout before start sending REC. We should
have waited long enough if there is truely data frames queued locally.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Vasu Dev ac166d2fbd [SCSI] libfc: fix retries with FDMI lport states
The FC-GS-3 sepc requires to wait for least 3 times R_A_TOV per
sec 4.6.1 "If the Requesting_CT does not receive a Response
CT_IU from the Responding_CT within three times R_A_TOV,
it shall consider this to be a protocol error."

This means added four new states with management server
could add significant delay with multiple retries
on default 12 second timeout(3 * R_A_TOV), so instead
just skip these states on very first timeout on any of
these states to not stuck with states for such longer
period.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Yi Zou db95fc004e [SCSI] libfc: don't exch_done() on invalid sequence ptr
The lport_recv(), i.e., fc_lport_recv_req() may get called w/o the sequence ptr
being set in fr_seq(), particularly in the case of vn2vn mode, this may happen
if the passive fcp provider, e.g., tcm_fc, has not been registered yet.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:56 +01:00
Vasu Dev b29a4f309f [SCSI] libfc: add exch timer debug info
Add exch timeout info to have debug log with exch timeout
value to match with retries, also add debug info
on exch timer cancel.

Added common fc_exch_timer_cancel() func and grouped this
along with fc_exch_timer_set() function, so that
added debug code is not repeated.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:58:55 +01:00
Vasu Dev 4e5fae7adb [SCSI] libfc: update fcp and exch stats
Updates newly added stats from fc_get_host_stats,
added new function fc_exch_update_stats to
update exches related stats from fc_exch.c
by going thru internal ema_list elements.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:31:48 +01:00
Vasu Dev 0f02a66528 [SCSI] libfc: adds FCP failures stats
Adds stats to track FCP pkt and frame alloc
failure.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:31:48 +01:00
Vasu Dev 1bd49b4820 [SCSI] libfc, fcoe, bnx2fc: cleanup fcoe_dev_stats
The libfc is used by fcoe but fcoe agnostic,
and therefore should not have any fcoe references.

So renaming fcoe_dev_stats from libfc as its for fc_stats.
After that libfc is fcoe string free except some strings for
Open-FCoE.org.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by : Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 08:31:47 +01:00
James Bottomley e346933365 isci update for 3.5
1/ Rework remote-node-context (RNC) handling for proper management of
    the silicon state machine in error handling and hot-plug conditions.
    Further details below, suffice to say if the RNC is mismanaged the
    silicon state machines may lock up.
 
 2/ Refactor the initialization code to be reused for suspend/resume support
 
 3/ Miscellaneous bug fixes to address discovery issues and hardware
    compatibility.
 
 RNC rework details from Jeff Skirvin:
 
 In the controller, devices as they appear on a SAS domain (or
 direct-attached SATA devices) are represented by memory structures known
 as "Remote Node Contexts" (RNCs).  These structures are transferred from
 main memory to the controller using a set of register commands; these
 commands include setting up the context ("posting"), removing the
 context ("invalidating"), and commands to control the scheduling of
 commands and connections to that remote device ("suspensions" and
 "resumptions").  There is a similar path to control RNC scheduling from
 the protocol engine, which interprets the results of command and data
 transmission and reception.
 
 In general, the controller chooses among non-suspended RNCs to find one
 that has work requiring scheduling the transmission of command and data
 frames to a target.  Likewise, when a target tries to return data back
 to the initiator, the state of the RNC is used by the controller to
 determine how to treat the incoming request. As an example, if the RNC
 is in the state "TX/RX Suspended", incoming SSP connection requests from
 the target will be rejected by the controller hardware.  When an RNC is
 "TX Suspended", it will not be selected by the controller hardware to
 start outgoing command or data operations (with certain priority-based
 exceptions).
 
 As mentioned above, there are two sources for management of the RNC
 states: commands from driver software, and the result of transmission
 and reception conditions of commands and data signaled by the controller
 hardware.  As an example of the latter, if an outgoing SSP command ends
 with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
 transition to the "TX Suspended" state, and this is signaled by the
 controller hardware in the status to the completion of the pending
 command as well as signaled in a controller hardware event.  Examples of
 the former are included in the patch changelogs.
 
 Driver software is required to suspend the RNC in a "TX/RX Suspended"
 condition before any outstanding commands can be terminated.  Failure to
 guarantee this can lead to a complete hardware hang condition.  Earlier
 versions of the driver software did not guarantee that an RNC was
 correctly managed before I/O termination, and so operated in an unsafe
 way.
 
 Further, the driver performed unnecessary contortions to preserve the
 remote device command state and so was more complicated than it needed
 to be.  A simplifying driver assumption is that once an I/O has entered
 the error handler path without having completed in the target, the
 requirement on the driver is that all use of the sas_task must end.
 Beyond that, recovery of operation is dependent on libsas and other
 components to reset, rediscover and reconfigure the device before normal
 operation can restart.  In the driver, this simplifying assumption meant
 that the RNC management could be reduced to entry into the suspended
 state, terminating the targeted I/O request, and resuming the RNC as
 needed for device-specific management such as an SSP Abort Task or LUN
 Reset Management request.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJPtYFXAAoJEB7SkWpmfYgCJkcP/1VvsuuitNy/YM9P1tb/RvQ7
 ytJzjGtWiAABHVWwjgB+Ng7hUTaP2r6l8KeNfwxpwXyNdBAUNysYEUBHAfPsKzKz
 espTmw3wVCnREajgKXZwFp9aTj8DcYFB6vKcC/ddACt3uRNjjA9En36+6797r8Vg
 YdebyjFX2FxwoUj0icTUiV/OXgb8w723imnCl8bfOhhFRi4eFZ4EJ23AdMkUya1i
 uYePAPJPSQJuU/87gNIx4JcR0qHJ1ziGPEY+XC47CzEeXbBTSPgWOwanQ6KPoXRJ
 XVxamfcKAjRdtwQ4m1vYBSE32RTdrjhujVbkGiPi6QaEbCLjhLSCIYyuS3XMckV+
 TCZ16o5kd/I6ZtZOeP4zZRGnNBkOPzY44qiJeKffjWDhTrFacx4XWJB/ftWPgEA5
 N2zFH3RM4sY0FUJ3I/Qe5CERNdCXMtcj+UAf3nHpAIVcv46Lp+qoSkdEx05uuuiN
 +D/dSlubktuvuzmB5WisL3qrjNEkkLTAGQpZs1j0ojLEBm0XAgV5EzqmHiZ0GOPD
 OQNFxeei9SlqgtKIIP0bymRispPrG2HVCOvExYMxzKR6fjxofZLAs/aWOsdhxgMq
 TlAyZJ6OmGI+KX68HHzoMpT9iquvmP64WGkfHzCx296BfSKiruLh/Jzt5gGwv+Z1
 5tlpnUr9dUTxx7qkQXvj
 =HYvO
 -----END PGP SIGNATURE-----

Merge tag 'isci-for-3.5' into misc

isci update for 3.5

1/ Rework remote-node-context (RNC) handling for proper management of
   the silicon state machine in error handling and hot-plug conditions.
   Further details below, suffice to say if the RNC is mismanaged the
   silicon state machines may lock up.

2/ Refactor the initialization code to be reused for suspend/resume support

3/ Miscellaneous bug fixes to address discovery issues and hardware
   compatibility.

RNC rework details from Jeff Skirvin:

In the controller, devices as they appear on a SAS domain (or
direct-attached SATA devices) are represented by memory structures known
as "Remote Node Contexts" (RNCs).  These structures are transferred from
main memory to the controller using a set of register commands; these
commands include setting up the context ("posting"), removing the
context ("invalidating"), and commands to control the scheduling of
commands and connections to that remote device ("suspensions" and
"resumptions").  There is a similar path to control RNC scheduling from
the protocol engine, which interprets the results of command and data
transmission and reception.

In general, the controller chooses among non-suspended RNCs to find one
that has work requiring scheduling the transmission of command and data
frames to a target.  Likewise, when a target tries to return data back
to the initiator, the state of the RNC is used by the controller to
determine how to treat the incoming request. As an example, if the RNC
is in the state "TX/RX Suspended", incoming SSP connection requests from
the target will be rejected by the controller hardware.  When an RNC is
"TX Suspended", it will not be selected by the controller hardware to
start outgoing command or data operations (with certain priority-based
exceptions).

As mentioned above, there are two sources for management of the RNC
states: commands from driver software, and the result of transmission
and reception conditions of commands and data signaled by the controller
hardware.  As an example of the latter, if an outgoing SSP command ends
with a OPEN_REJECT(BAD_DESTINATION) status, the RNC state will
transition to the "TX Suspended" state, and this is signaled by the
controller hardware in the status to the completion of the pending
command as well as signaled in a controller hardware event.  Examples of
the former are included in the patch changelogs.

Driver software is required to suspend the RNC in a "TX/RX Suspended"
condition before any outstanding commands can be terminated.  Failure to
guarantee this can lead to a complete hardware hang condition.  Earlier
versions of the driver software did not guarantee that an RNC was
correctly managed before I/O termination, and so operated in an unsafe
way.

Further, the driver performed unnecessary contortions to preserve the
remote device command state and so was more complicated than it needed
to be.  A simplifying driver assumption is that once an I/O has entered
the error handler path without having completed in the target, the
requirement on the driver is that all use of the sas_task must end.
Beyond that, recovery of operation is dependent on libsas and other
components to reset, rediscover and reconfigure the device before normal
operation can restart.  In the driver, this simplifying assumption meant
that the RNC management could be reduced to entry into the suspended
state, terminating the targeted I/O request, and resuming the RNC as
needed for device-specific management such as an SSP Abort Task or LUN
Reset Management request.
2012-05-21 12:17:30 +01:00
Vasu Dev 061446a159 [SCSI] libfc: flush lport worker after its disabled
The lport could get timeout armed while its getting disabled,
so flush lport worker after its disabled and ignore lport
retry in that case instead of WARN_ON.

 [13192.936858] WARNING: at drivers/scsi/libfc/fc_lport.c:1573 fc_lport_timeout+0x53/0xa9 [libfc]()
 [13192.938026] Hardware name: Bochs
 [13192.938620] Modules linked in: fcoe libfcoe libfc scsi_transport_fc scsi_tgt fuse 8021q garp stp llc sunrpc ipv6 uinput microcode joydev pcspkr ixgbe e1000 i2c_piix4 i2c_core virtio_balloon dca mdio virtio_blk virtio_pci virtio_ring virtio floppy [last unloaded: speedstep_lib]
 [13192.942589] Pid: 23605, comm: kworker/0:6 Tainted: G        W    3.2.0+ #71
 [13192.943587] Call Trace:
 [13192.944052]  [<ffffffff810403f4>] warn_slowpath_common+0x85/0x9d
 [13192.944940]  [<ffffffff81040426>] warn_slowpath_null+0x1a/0x1c
 [13192.945734]  [<ffffffffa02746eb>] fc_lport_timeout+0x53/0xa9 [libfc]
 [13192.946665]  [<ffffffff81058d88>] process_one_work+0x20c/0x3ad
 [13192.947541]  [<ffffffff81058cbe>] ? process_one_work+0x142/0x3ad
 [13192.948423]  [<ffffffffa0274698>] ? fc_lport_enter_ns+0x178/0x178 [libfc]
 [13192.949363]  [<ffffffff8105a313>] worker_thread+0xfd/0x181
 [13192.950191]  [<ffffffff8105a216>] ? manage_workers.clone.15+0x173/0x173
 [13192.951100]  [<ffffffff8105e19b>] kthread+0xa4/0xac
 [13192.951755]  [<ffffffff814edbb4>] kernel_thread_helper+0x4/0x10
 [13192.952520]  [<ffffffff814e5cb4>] ? retint_restore_args+0x13/0x13
 [13192.953398]  [<ffffffff8105e0f7>] ? __init_kthread_worker+0x5b/0x5b
 [13192.954278]  [<ffffffff814edbb0>] ? gs_change+0x13/0x13
 [13192.954911] ---[ end trace 9763213b95bbd803 ]---

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-05-10 08:59:25 +01:00
Vasu Dev 93f90e5186 [SCSI] libfc: update mfs boundry checking
A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.

This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-04-25 08:46:29 +01:00
Linus Torvalds a75ee6ecd4 SCSI updates on 20120331
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPdrIWAAoJEDeqqVYsXL0Mny4IAMTzXGOXCykpWhdIe2R8w0Ys
 eIoTJhBKoQWnLTV8cOODtwmtZcoQLeXkZmizZiAJvX6O1tOgueg+W4AFa9grxXGI
 O0d1bSb2ardzU7VZrZSY60Hd4bylMwn4Xv/0dRrQMwTJO0LEeGWsJPV2+2BuXwMB
 lGCNB67oUBXgMOI1jUZQRwx/mBzQ3e/gINjnpZTNKHia7YkX/yVTFISq7htgfDN7
 1wRGxymbHtVap3NbtUO96BUUndAiF5vom+4WNvaQUyPrCc6aoGWjv+J9DQXY/zgv
 AYjujAluK396D6YncGFAWBzYOg9WFbq54v0PRUanjcTTAu5ILs2BxqWdhmnvl14=
 =IH8T
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

Pull SCSI updates from James Bottomley:
 "This is primarily another round of driver updates (lpfc, bfa, fcoe,
  ipr) plus a new ufshcd driver.  There shouldn't be anything
  controversial in here (The final deletion of scsi proc_ops which
  caused some build breakage has been held over until the next merge
  window to give us more time to stabilise it).

  I'm afraid, with me moving continents at exactly the wrong time,
  anything submitted after the merge window opened has been held over to
  the next merge window."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (63 commits)
  [SCSI] ipr: Driver version 2.5.3
  [SCSI] ipr: Increase alignment boundary of command blocks
  [SCSI] ipr: Increase max concurrent oustanding commands
  [SCSI] ipr: Remove unnecessary memory barriers
  [SCSI] ipr: Remove unnecessary interrupt clearing on new adapters
  [SCSI] ipr: Fix target id allocation re-use problem
  [SCSI] atp870u, mpt2sas, qla4xxx use pci_dev->revision
  [SCSI] fcoe: Drop the rtnl_mutex before calling fcoe_ctlr_link_up
  [SCSI] bfa: Update the driver version to 3.0.23.0
  [SCSI] bfa: BSG and User interface fixes.
  [SCSI] bfa: Fix to avoid vport delete hang on request queue full scenario.
  [SCSI] bfa: Move service parameter programming logic into firmware.
  [SCSI] bfa: Revised Fabric Assigned Address(FAA) feature implementation.
  [SCSI] bfa: Flash controller IOC pll init fixes.
  [SCSI] bfa: Serialize the IOC hw semaphore unlock logic.
  [SCSI] bfa: Modify ISR to process pending completions
  [SCSI] bfa: Add fc host issue lip support
  [SCSI] mpt2sas: remove extraneous sas_log_info messages
  [SCSI] libfc: fcoe_transport_create fails in single-CPU environment
  [SCSI] fcoe: reduce contention for fcoe_rx_list lock [v2]
  ...
2012-03-31 13:31:23 -07:00
Steven Clark 011a9008b1 [SCSI] libfc: fcoe_transport_create fails in single-CPU environment
Starting fcoe fails at fcoe_transport_create when attempting to allocate a
pool of 4K exchanges on a 64-bit single-CPU environment because the call to
__alloc_percpu() is greater than the max of 32K.  This patch reduces the
number of exchanges to fit within the maximum allowed space.

[ Whitespace problems fixed by Robert Love to satisfy chechpatch.pl ]

Signed-off-by: Steven Clark <sclark@crossbeam.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-28 09:33:04 +01:00
Vasu Dev 73d67aa40b [SCSI] libfc: update fc_host mfs along with updating lport->mfs
Currently fc_host mfs is not getting updated in
case its changed during FLOGI and that leaves fc_host
to show its initial old value in sysfs, so instead
have fc_host mfs updated along with updating lport mfs
during FLOGI.

Also in case of bad mfs during flogi, error out
instead of continuing with flogi.

[ Changes made by Robert Love: condition to '>=' and
  added printing of lport->mfs in DBG statement. FLOGI
  resp processing failed without being able to compare
  FCoE MFS 2112 against an incoming MFS of 2112 ]

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-03-28 09:04:51 +01:00
Linus Torvalds 424a6f6ef9 SCSI updates on 20120319
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
 CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
 2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
 tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
 +AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
 uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
 =1TxB
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6

SCSI updates from James Bottomley:
 "The update includes the usual assortment of driver updates (lpfc,
  qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
  amount of infrastructure work in the SAS library and transport class
  as well as an iSCSI update.  There's also a new SCSI based virtio
  driver."

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
  [SCSI] qla4xxx: Update driver version to 5.02.00-k15
  [SCSI] qla4xxx: trivial cleanup
  [SCSI] qla4xxx: Fix sparse warning
  [SCSI] qla4xxx: Add support for multiple session per host.
  [SCSI] qla4xxx: Export CHAP index as sysfs attribute
  [SCSI] scsi_transport: Export CHAP index as sysfs attribute
  [SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
  [SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
  [SCSI] pm8001: fix endian issue with code optimization.
  [SCSI] pm8001: Fix possible racing condition.
  [SCSI] pm8001: Fix bogus interrupt state flag issue.
  [SCSI] ipr: update PCI ID definitions for new adapters
  [SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
  [SCSI] isci: improvements in driver unloading routine
  [SCSI] isci: improve phy event warnings
  [SCSI] isci: debug, provide state-enum-to-string conversions
  [SCSI] scsi_transport_sas: 'enable' phys on reset
  [SCSI] libsas: don't recover end devices attached to disabled phys
  [SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
  [SCSI] libsas: set attached device type and target protocols for local phys
  ...
2012-03-22 12:55:29 -07:00
Linus Torvalds 1ab142d499 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
 "This contains the usual set of updates and bugfixes to target-core +
  existing fabric module code, along with a handful of the patches
  destined for v3.3 stable.

  It also contains the necessary target-core infrastructure pieces
  required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
  Channel fabric module currently queued in target-pending/for-next-merge,
  and coming for round 2.

  The highlights for this series include:

   - Add target_submit_tmr() helper function for fabric task management
     (andy)
   - Convert tcm_fc to use target_submit_tmr() (andy)
   - Replace target core various cmd flags with a transport state (hch)
   - Convert loopback to use workqueue submission (hch)
   - Convert target core to use array_zalloc for tpg_lun_list (joern)
   - Convert target core to use array_zalloc for device_list (joern)
   - Add target core support for TMR_ABORT_TASK (nab)
   - Add target core se_sess->sess_kref + get/put helpers (nab)
   - Add target core se_node_acl->acl_kref for ->acl_free_comp usage
     (nab)
   - Convert iscsi-target to use target_put_session + sess_kref (nab)
   - Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
   - Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
     exception (nab)
   - Fix target core up handling of short INQUIRY buffers (roland)
   - Untangle target-core front-end and back-end meanings of max_sectors
     attribute (roland)
   - Set loopback residual field for SCSI commands (roland)
   - Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
     emulation (roland)

  Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
  contributed this round!"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
  ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
  loopback: Fix transport_generic_allocate_tasks error handling
  iscsi-target: remove improper externs
  iscsi-target: Remove unused variables in iscsi_target_parameters.c
  target: remove obvious warnings
  target: Use array_zalloc for device_list
  target: Use array_zalloc for tpg_lun_list
  target: Fix sense code for unsupported SERVICE ACTION IN
  target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
  target: Bump core version to v4.1.0-rc2-ml + fabric versions
  tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
  target: Drop unused legacy target_core_fabric_ops API callers
  iscsi-target: Convert to use target_put_session + sess_kref
  target: Convert se_node_acl->acl_group removal to use ->acl_kref
  target: Add se_node_acl->acl_kref for ->acl_free_comp usage
  target: Add se_node_acl->acl_free_comp for NodeACL release path
  target: Add se_sess->sess_kref + get/put helpers
  target: Convert session_lock to irqsave
  target: Fix typo in drivers/target
  iscsi-target: Fix dynamic -> explict NodeACL pointer reference
  ...
2012-03-22 12:38:04 -07:00
Cong Wang 77dfce076c scsi: remove the second argument of k[un]map_atomic()
Signed-off-by: Cong Wang <amwang@redhat.com>
2012-03-20 21:48:19 +08:00
Andy Grover e35fa8c2d0 scsi: Use struct scsi_lun in fc/fcp.h
This allows us to use scsilun_to_int without an ugly cast.

Fix up places that use scsilun_to_int on fcp->fc_lun accordingly.

In fc target, this leaves ft_cmd.lun unused, so remove it.

Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kiran Patil <kiran.patil@intel.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
2012-02-25 14:37:46 -08:00
Bhanu Prakash Gollapudi 0083208473 [SCSI] libfc: Handle discovery failure during ctlr link down
While we wait for GPN_FT response, if the ctlr link goes down, the stack
generates a completion for GPN_FT with error FC_EXCH_CLOSED, and reports a
discovery error. Discovery is not retried in this case, and rightly so.
However, the 'pending' flag stays set, which does not allow subsequent
discovery to succeed as GPN_FT will never be issued. Fix it by clearing the
pending flag when the discovery fails due to GPN_FT failure.

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:27:26 -06:00
Bhanu Prakash Gollapudi d4042e9c84 [SCSI] libfc: Fix panic in fc_exch_recv
Adding and removing the host into the zone causes this panic.

BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
IP: [<ffffffffa0491707>] fc_exch_recv+0xc57/0xe70 [libfc]
Call Trace:
[<ffffffffa050e04b>] bnx2fc_l2_rcv_thread+0x37b/0x430 [bnx2fc]
[<ffffffffa050dcd0>] ? bnx2fc_l2_rcv_thread+0x0/0x430 [bnx2fc]
[<ffffffff81090886>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff810907f0>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20

During fc_exch_reset, the active exchanges are aborted and the exch is deleted.
As part of processing ABTS response, due to 'ep' being NULL, any access to ep in
fc_exch_recv_bls() causes this panic. Fixed to access 'ep' only if non-NULL.

Reviewed-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 09:26:07 -06:00
Neerav Parikh d78c317f6c [SCSI] libfc: Add support for FDMI
This patch adds support for Fabric Device Management
Interface as per FC-GS-4 spec. in libfc. Any driver
making use of libfc can enable fdmi state machine
for a given lport.

If lport has enabled FDMI support the lport state
machine will transition into FDMI after completing
the DNS states and before entering the SCR state.
The FDMI state transition is such that if there is an
error, it won't stop the lport state machine from
transitioning and the it will behave as if there was
no FDMI support.

The FDMI HBA attributes are registed with the Management
server via Register HBA (RHBA) command and the port
attributes are reigstered using the Register Port(RPA)
command.

Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:08:58 -06:00
Neerav Parikh 1ea2c1daf4 [SCSI] libfc: Make the libfc Common Transport(CT) code generic
Currently the libfc Common Transport(CT) calls assume that
the CT requests are Name Server specific only. This patch
makes it more flexible to allow more FC-GS services to make
use of these routines.

Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-02-19 08:08:58 -06:00
Yi Zou 76ffe8a3f7 [SCSI] libfc: remove redundant timer init for fcp
The fcp timer is already initialized when it gets allocated.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:47:18 +04:00
Bart Van Assche c6b21c93c1 [SCSI] libfc: Declare local functions static
Avoid that sparse complains about missing declarations for local
functions by declaring these static or by adding an #include directive.
Add the __percpu annotation where it is missing.

Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-01-16 12:45:48 +04:00
Linus Torvalds 32aaeffbd4 Merge branch 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
  Revert "tracing: Include module.h in define_trace.h"
  irq: don't put module.h into irq.h for tracking irqgen modules.
  bluetooth: macroize two small inlines to avoid module.h
  ip_vs.h: fix implicit use of module_get/module_put from module.h
  nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
  include: replace linux/module.h with "struct module" wherever possible
  include: convert various register fcns to macros to avoid include chaining
  crypto.h: remove unused crypto_tfm_alg_modname() inline
  uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
  pm_runtime.h: explicitly requires notifier.h
  linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
  miscdevice.h: fix up implicit use of lists and types
  stop_machine.h: fix implicit use of smp.h for smp_processor_id
  of: fix implicit use of errno.h in include/linux/of.h
  of_platform.h: delete needless include <linux/module.h>
  acpi: remove module.h include from platform/aclinux.h
  miscdevice.h: delete unnecessary inclusion of module.h
  device_cgroup.h: delete needless include <linux/module.h>
  net: sch_generic remove redundant use of <linux/module.h>
  net: inet_timewait_sock doesnt need <linux/module.h>
  ...

Fix up trivial conflicts (other header files, and  removal of the ab3550 mfd driver) in
 - drivers/media/dvb/frontends/dibx000_common.c
 - drivers/media/video/{mt9m111.c,ov6650.c}
 - drivers/mfd/ab3550-core.c
 - include/linux/dmaengine.h
2011-11-06 19:44:47 -08:00
Paul Gortmaker acf3368ffb scsi: Fix up files implicitly depending on module.h inclusion
The module.h header was implicitly present everywhere, so files
with no explicit include of the module infrastructure would build
anyway.  We are now removing the implicit include, and so we need
to call out the module.h file that we need explicitly.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:24 -04:00
Paul Gortmaker 09703660ed scsi: Add export.h for EXPORT_SYMBOL/THIS_MODULE as required
For the basic SCSI infrastructure files that are exporting symbols
but not modules themselves, add in the basic export.h header file
to allow the exports.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-31 19:31:23 -04:00
Vasu Dev 907c07d451 [SCSI] libfc: improve flogi retries to avoid lport stuck
Adds more cases to do flogi retry, now also retry
on getting bad response due to either no ELS response
or flogi response payload length not large enough.
In those cases flogi was not retried and that
was leaving lport offline.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:27:43 +04:00
Vasu Dev b6e3c84034 [SCSI] libfc: avoid exchanges collision during lport reset
Currently timer delay is large and is using msleep to avoid
avoid exchanges collision across lport reset, so instead
do this by initializing exches pool indexes during
reset also.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:27:19 +04:00
Vasu Dev 14fc315fa3 [SCSI] libfc: fix checking FC_TYPE_BLS
Its checked after skb freed, so instead have fh_type
cached and then check FC_TYPE_BLS against cached
fh_type value.

This wrong check was causing double exch locking as
reported by Bhanu at
https://lists.open-fcoe.org/pipermail/devel/2011-October/011793.html

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-31 13:26:44 +04:00
Linus Torvalds ec7ae51753 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (204 commits)
  [SCSI] qla4xxx: export address/port of connection (fix udev disk names)
  [SCSI] ipr: Fix BUG on adapter dump timeout
  [SCSI] megaraid_sas: Fix instance access in megasas_reset_timer
  [SCSI] hpsa: change confusing message to be more clear
  [SCSI] iscsi class: fix vlan configuration
  [SCSI] qla4xxx: fix data alignment and use nl helpers
  [SCSI] iscsi class: fix link local mispelling
  [SCSI] iscsi class: Replace iscsi_get_next_target_id with IDA
  [SCSI] aacraid: use lower snprintf() limit
  [SCSI] lpfc 8.3.27: Change driver version to 8.3.27
  [SCSI] lpfc 8.3.27: T10 additions for SLI4
  [SCSI] lpfc 8.3.27: Fix queue allocation failure recovery
  [SCSI] lpfc 8.3.27: Change algorithm for getting physical port name
  [SCSI] lpfc 8.3.27: Changed worst case mailbox timeout
  [SCSI] lpfc 8.3.27: Miscellanous logic and interface fixes
  [SCSI] megaraid_sas: Changelog and version update
  [SCSI] megaraid_sas: Add driver workaround for PERC5/1068 kdump kernel panic
  [SCSI] megaraid_sas: Add multiple MSI-X vector/multiple reply queue support
  [SCSI] megaraid_sas: Add support for MegaRAID 9360/9380 12GB/s controllers
  [SCSI] megaraid_sas: Clear FUSION_IN_RESET before enabling interrupts
  ...
2011-10-28 16:44:18 -07:00
Vasu Dev e17b4af7c7 [SCSI] libfc: cache align fc_exch_pool
fix holes and better cache aligned fields.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 12:56:50 -05:00
Vasu Dev ed26cfece6 [SCSI] libfc: cache align struct fc_fcp_pkt fields
Re-arrange its fields to avoid padding and have better
cacheline alignments.

Removed not used start_time, end_time and last_pkt_time
fields.

This all reduced this struct size to 448 from 480 and
that also reduced one cacheline on x86_64 beside
eliminating 8 pads. However kept logical fields together.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-10-02 12:55:07 -05:00
Yi Zou 3ee17f59c5 [SCSI] libfc: fix referencing to fc_fcp_pkt from the frame pointer via fr_fsp()
In commit 6a716a8, while releasing the DDP context in case frame_send() failed,
the frame may already be freed, so we should store the pointer to fc_fcp_pkt and
release the DDP context using the locally stored fsp instead of getting fsp from
the fr_fsp(fp) on a frame.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-28 19:40:30 -07:00
Vasu Dev 21cc0bd3a9 [SCSI] libfc: block SCSI eh thread for blocked rports
Call fc_block_scsi_eh() in all fcoe eh to blocks
the scsi_eh thread for blocked rports.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-28 19:40:12 -07:00
Vasu Dev 77a2b73a78 [SCSI] libfc: fix fc_eh_host_reset
Current fc_eh_host_reset leaves lport offline
permanently  due to FLOGI response getting
handled by LOGO response from last reset as both
had same exchange id.

So fix this by having end to end exches clean-up
using exchange abort along exches reset
done from fc_eh_host_reset. This would avoid
exchanges collision between the sessions across
the reset. In this case implicit login should have
done that but no aborting support for FIP
frames, so just wait till lport->r_a_tov before
restarting next flogi to ensure all exchanges
are good to use again for next session.

Below is the trace of LOGO from older session
coming ahead of FLOGI response with same exche id
0x203:-

617  86.435165     4e.00.0b -> ff.ff.fc     FC ELS LOGO 0x203
618  86.435195     4e.00.0b -> b6.02.00     FC ELS LOGO 0x213
619  86.435220     4e.00.0b -> 18.03.00     FC ELS LOGO 0x223
620  86.435244     4e.00.0b -> 18.02.00     FC ELS LOGO 0x233
621  86.435267     4e.00.0b -> 18.01.00     FC ELS LOGO 0x243
622  86.435349     00.00.00 -> ff.ff.fe     FC ELS FLOGI 0x203
623  86.435549     ff.ff.fc -> 4e.00.0b     FC ELS ACC (LOGO) 0x203
624  86.438721     ff.ff.fe -> 4e.00.0b     FC ELS ACC (FLOGI) 0x203
625  86.442059     18.03.00 -> 4e.00.0b     FC ELS ACC (LOGO) 0x223
626  86.443683     b6.02.00 -> 4e.00.0b     FC ELS ACC (LOGO) 0x213
627  86.447693     18.01.00 -> 4e.00.0b     FC ELS ACC (LOGO) 0x243
628  86.453499     18.02.00 -> 4e.00.0b     FC ELS ACC (LOGO) 0x233

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-08-28 19:39:37 -07:00
Vasu Dev 320036e083 [SCSI] libfc: fix warn on in lport retry
The lport retry timer hits warn on in case
it has become ready in response from fip
login from fcoe_ctlr_flogi_send(), this is
possible but safe code path, therefore
removing this warn on.

Jun 22 03:16:30 10.0.16.6 [488198.316517] host3: Assigned Port ID 180f02
Jun 22 03:16:32 10.0.16.6 [488200.091561] ------------[ cut here ]------------
Jun 22 03:16:32 10.0.16.6 [488200.091586] WARNING: at
drivers/scsi/libfc/fc_lport.c:1355 fc_lport_timeout+0xd9/0xe0 [libfc]()

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:13:36 +04:00
Neerav Parikh c9d24a7618 [SCSI] libfc: Remove the reference to FCP packet from scsi_cmnd in case of error
fc_queuecommand() allocates an FCP packet for each SCSI command and sends
it out on the wire. In the process it stores the reference to the FCP packet
in the scsi_cmnd structure.
Now, in case under stress testing the libfc exchange layer runs out of
exchanges the fc_queuecommand() may not be able to send out commands out on
the wire. In such a scenario if there is an error in sending the FCP packet
out the wire; fc_queuecommand() deletes the FCP packet from internal queue,
releases the FCP packet and returns a SCSI_MLQUEUE_HOST_BUSY status to the
scsi-ml. But, the reference to the FCP packet set in the scsi_cmnd is not
removed from the scsi_cmnd in this code path.

This might lead to a crash under stress testing where the scsi_cmnd failed by
fc_queuecommand() comes up to fc_eh_abort() via scsi eh thread. fc_eh_abort()
will get reference to the FCP packet to be aborted from the scsi_cmnd for
further FCP abort related processing and then try to release the FCP packet
that has already been released.

This patch removes the FCP packet reference from the scsi_cmnd before returning
back from fc_queuecommand() in case of an error in sending out the FCP packet.

Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:13:15 +04:00
Hillf Danton 8598212727 [SCSI] libfc: cleanup sending SRR request
The variable on stack, namely cdb_op, is not used but removed.

[ Patch reworked by Robert Love due to invalid patch format ]

Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:12:27 +04:00
Hillf Danton 547fb12b7a [SCSI] libfc: two minor changes in comments
One change is to cleanup typo in comment for fc_fcp_recv(), another corrects
the misleading comment for fc_fcp_abts_resp().

[ Patch reworked by Robert Love due to invalid patch format ]

Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:12:06 +04:00
Vasu Dev 324f667833 [SCSI] libfc, fcoe: ignore rx frame with wrong xid info
Drop the rx frame having xid with wrong cpu info
or received with xid  not matching to our xid.

Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:10:35 +04:00
Hillf Danton 6f06e3a7b2 [SCSI] libfc: release exchg cache
If fail to create workqueue, the newly created cache for exchg has to be
released.

Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:10:13 +04:00
Hillf Danton 688fd36427 [SCSI] libfc: use FC_MAX_ERROR_CNT
Though defined, FC_MAX_ERROR_CNT is not used. It is used now for CRC error in
the path of receiving FCP frame.

Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-07-28 12:09:36 +04:00
Linus Torvalds d4e06701b8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
  [SCSI] fix crash in scsi_dispatch_cmd()
  [SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
  [SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
  [SCSI] bfa: Update the driver version to 3.0.2.1
  [SCSI] bfa: Driver and BSG enhancements.
  [SCSI] bfa: Added support to query PHY.
  [SCSI] bfa: Added HBA diagnostics support.
  [SCSI] bfa: Added support for flash configuration
  [SCSI] bfa: Added support to obtain SFP info.
  [SCSI] bfa: Added support for CEE info and stats query.
  [SCSI] bfa: Extend BSG interface.
  [SCSI] bfa: FCS bug fixes.
  [SCSI] bfa: DMA memory allocation enhancement.
  [SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
  [SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
  [SCSI] bfa: Added Fabric Assigned Address(FAA) support
  [SCSI] bfa: IOC bug fixes.
  [SCSI] bfa: Enable ASIC block configuration and query.
  [SCSI] bnx2i: Updated copyright and bump version
  [SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
  ...

Fix up some trivial conflicts in:
 - drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
	Crazy broadcom version number conflicts
 - drivers/target/tcm_fc/tfc_cmd.c
	Just trivial cleanups done on adjacent lines
2011-07-23 11:13:11 -07:00
Lai Jiangshan 8497a24a43 scsi,rcu: Convert call_rcu(fc_rport_free_rcu) to kfree_rcu()
The rcu callback fc_rport_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(fc_rport_free_rcu).

Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
2011-07-20 14:10:12 -07:00
Vasu Dev 9b7d1613a9 [SCSI] libfc: post reset event on lport reset
Post an FCH_EVT_LIPRESET event on lport reset as
as lport reset occurs on FIP cleat virtual link,
this could be due to change in fcoe vlan and this
event will allow user app fcoemon to switch to
new fcoe vlan.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 16:33:22 -05:00
Kiran Patil e3e65c69c3 [SCSI] libfc:Fix for exchange/seq loopup failure when FCoE stack is used as target and connected to windows initaitor
Problem: Linux based SW target (TCM) connected to windows initiator
was unable to satisfy write request of size > 2K.

Fix: Existing linux implememtation of FCoE stack is expecting sequence
number to match w.r.t incoming framme. When DDP is used on target in
response to write request from initiator, SW stack is notified only
when last data frame arrives and only the pakcket header of last data
frame is posted to NetRx queue of storage. When that last packet was
processed in libfc:Exchange layer, implementation was expecting
sequence number to match, but in this case sequence number which is
embedded in FC Header is assigned by windows initaitor, hence due to
sequence number mismatch post-processing which shall result into
sending RSP is not done. Enhanced the code to utilize the sequence
number of incoming last frame and process the packet so that, it will
eventually complete the write request by sending write response (RSP)
GOOD.

Notes/Dependencies: This patch is validated using windows and linux
initiator to make sure, it doesn't break anything.

Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 16:30:17 -05:00
Kiran Patil 480584818a [SCSI] libfc: Enhancement to RPORT state machine applicable only for VN2VN mode
Problem: Existing RPORT state machine continues witg FLOGI/PLOGI
process only after it receices beacon from other end. Once claiming
stage is over (either clain notify or clain repose), beacon is sent
and state machine enters into operational mode where it initiates the
rlogin process (FLOGI/PLOGI) to the peer but before this rlogin is
initiated, exitsing implementation checks if it received beacon from
other end, it beacon is not received yet, rlogin process is not
initiated. Other end initiates FLOGI but peer end keeps on rejecting
FLOGI, hence after 3 retries other end deletes associated rport, then
sends a beacon. Once the beacon is received, peer end now initiates
rlogin to the peer end but since associated rport is deleted FLOGI is
neither accepted nor the reject response send out because rport is
deleted. Hence unable to proceed withg FLOGI/PLOGI process and fails
to establish VN2VN connection.

Fix: VN2VN spec is not standard yet but based on exitsing collateral
on T11, it appears that, both end shall send beacon and enter into
'operational mode' without explictly waiting for beacon from other
end. Fix is to allow the RPORT login process as long as respective
RPORT is created (as part of claim notification / claim response) even
though state of RPORT is INIT. Means don't wait for beacon from peer
end, if peer end initiates FLOGI (means peer end exist and
responding).

Notes: This patch is preparing the FCoE stack for target wrt
offload. This is generic patch and harmless even if applied on storage
initiator because 'else if' condition of function 'fcoe_oem_found'
shall evaluate to TRUE only for targets.

Dependencies: None

Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2011-06-29 16:28:33 -05:00
Yi Zou 8467b96c03 [SCSI] libfc: do not immediately retry the cmd when seq_send fails in fc_fcp_send_data
Currently, when seq_send() fails in fc_fcp_send_data(),
fc_fcp_retry_cmd() would complete this failed I/O directly and let
scsi-ml retry. However, target side is not notified which may hang the
target. Instead, we should just bail out from from fc_fcp_send_data
and let scsi-ml times it out and aborts this I/O instead.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:37:25 -04:00
Vasu Dev 0a219edb26 [SCSI] libfc: fix race in SRR response
In this case fsp was freed before error handler was invoked,
this is fixed by having SRR fsp reference freed by exch
destructor so that fsp will be always held until it exch
is freed.

Also don't reset fsp->recov_seq since this is needed by
SRR error handler to do exch done.

Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
2011-05-24 12:37:15 -04:00