The current code writes a set of registers that are reserved on the
tlc320aic3104. The change skips those registers for that IC.
Signed-off-by: Rick Mann <rmann@latencyzero.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this patch the set_tdm_slots() callback did not store the value
of slot width anywhere. The tdm support only worked if selected slot
width was equal to the sample width. With this patch all sample widths
that fit into the slot width are supported. There unused bits are
filled unnecessarily in the capture direction, but the other end of
the i2s bus should be able to ignore them.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and replace all
other manual access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The intercon_extra_3104 is obviously for tlv320aic3104.
Reported-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disables GPIO support and LINE2 input and renames Mic3 input to Mic2,
if tlv320aic3104 mode is seleced. Devicetree binding document is
updated accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue introduced by:
3684940933 ASoC: tlv320aic3x: Add TDM support
The CTRLC register were not receiving the correct delay configuration,
which will corrupt DSP_A audio mode.
Fixes: 3684940933 (ASoC: tlv320aic3x: Add TDM support)
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Output driver has two parameters that can be configured to reduce
pop noise: power-on delay and ramp-up step time. Two new kcontrols
have been added to set these parameters.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is easier to find the relevant enums in the code. Use the
SOC_ENUM_*_DECL macro for the individual items.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM support is achieved using DSP transfer mode and setting a
programmable offset which specifies where data begins with
respect to the frame sync.
It requires 256-clock mode if CODEC is master (not currently
supported in the driver). No additional dependency if CODEC
is slave.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current caching implementation during regcache_sync() call bypasses
all register writes of values that are already known as default
(regmap reg_defaults). Same time in TLV320AIC3x codecs register 5
(AIC3X_PLL_PROGC_REG) write should be immediately followed by register
6 write (AIC3X_PLL_PROGD_REG) even if it was not changed. Otherwise
both registers will not be written.
This brings to issue that appears particulary in case of 44.1kHz
playback with 19.2MHz master clock. In this case AIC3X_PLL_PROGC_REG
is 0x6e while AIC3X_PLL_PROGD_REG is 0x0 (same as register
default). Thus AIC3X_PLL_PROGC_REG also remains not written and we get
wrong playback speed.
In this patch snd_soc_read() is used to get cached pll values and
snd_soc_write() (unlike regcache_sync() this function doesn't bypasses
hardware default values) to write them to registers.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The ASoC core will only call the suspend/resume callbacks when the device's
DAPM context is idle. Since this driver sets idle_bias_off to true this
means that the device is already in SND_SOC_BIAS_OFF when the suspend
callback is called, so there is no need to manually set this state again.
There is also no need to go to SND_SOC_BIAS_STANDBY in the resume callback
since the core will go right back to SND_SOC_BIAS_OFF.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec need to be configured to 24bit mode in case of S24_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Correct the hw_params callback to configure the codec correctly in case of
S24_3LE format since in case of S24_3LE the codec has been configured to
16bit format mode.
S24_LE is not defined as supported format for the codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some unknown reason the parameters for snd_soc_test_bits() were in wrong
order:
It was:
snd_soc_test_bits(codec, val, mask, reg); /* WRONG!!! */
while it should be:
snd_soc_test_bits(codec, reg, mask, val);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Currently the second tlv320aic3x instance fails to
be probed from DT if the reset pin is shared with
the first one.
This patch fixes it by moving the list add of the
reset pin into the i2c_probe method.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
if codec driver is used for AIC3X_MODEL_3007 the mono iout controls overwrite
registers for class-d amplifier.
classd amplifier controls are only used for AIC3X_MODEL_3007.
Removing all mono snd_kcontrol_new, snd_soc_dapm_widget, snd_soc_dapm_route
and aic3x_init stuff from common code and call only for not AIC3X_MODEL_3007
codecs.
Testet only with AIC3X_MODEL_3007
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The two paths were not connected in the DAPM route causing the associated
routes to be non working and the following warnings printed in the logs:
tlv320aic3x-codec 0-001b: ASoC: mux Right Line1L Mux has no paths
tlv320aic3x-codec 0-001b: ASoC: mux Left Line1R Mux has no paths
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is slightly more complex than a standard regmap conversion due to
the moderately detailed cache control and the open coding of a register
patch for the class D speaker on the TLV320AIC3007.
Although the device supports paging this is not currently implemented as
the additional pages are only used during the application of the patch
for the TLV320AIC3007.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than referencing the cache directly read back the values we are
going to restore, supporting refactoring to use regmap.
Signed-off-by: Mark Brown <broonie@linaro.org>
Every statement in this comment is incorrect either through bitrot or
(mostly) through never having corresponded to reality in the first place.
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same 3 lines to get the CODEC for a kcontrol in a quite a few places.
This patch puts them into a common helper function. Having this encapsulated in
a helper function will also make it more easier to eventually change the data
layout of the kcontrol's private data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_soc_dapm_mixer_update_power() instead of reimplementing its
functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver supports a range of devices but currently doesn't allow those
device names to be used for enumeration on DT. Add the currently listed
I2C IDs as compatible strings.
Signed-off-by: Mark Brown <broonie@linaro.org>
When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex
already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By
moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is
prevented. This problem was introduced in Linux 3.5
Signed-off-by: Andreas Irestål <Andreas.Irestal@axis.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert MicBias widgets to supply widget.
On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage. So, when power on mic bias, we need
reclaim it to voltage value.
Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg" platform data.
Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.
Since micbias is converted to supply widget, updated machine drivers as
well.
This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Takashi Iwai
Rick Mann
Jyri Sarha
Mark Brown
Nariman Poushin
Krzysztof Kozlowski
Lars-Peter Clausen
Peter Ujfalusi
Misael Lopez Cruz
Dmitry Lavnikevich
Mark Brown
Sachin Kamat
Sebastian Reichel
Xiubo Li
Jan Weitzel
Sachin Kamat
Andreas Irestål
Mark Brown
Hebbar Gururaja